Carrier Transport Behaviour of Molecular Doped Poly（N—Vinylcabozole）in Polymer Light—Emitting Diodes

Single-layer polymer light-emitting diodes are prepared from blends of poly(N-vinylcarbozole)(PVK) doped with tris(8-hydroxy-quinoline)aluminium(Alq3) of 2wt%(sample a)and 0.2wt%(sample b).The onset of PVK transient electroluminescence(EL) is delayed with respect to that of Alq3 in sample a under pulsed excitation,while the EL onsets of Alq3 and PVK in sample b are simultaneous.The total carrier mobility of the Alq3-rich regions in sample a is larger than that of the PVK-rich regions.However,the total carrier mobility is homogeneous in sample b.the phase image of atomic force microscopy and photoluminescence spectra of samples a and b indicate that the separated phase of samples a and b exists in the PVK-rich and Alq3-rich regions.The variance of the doping concentration and separated phase in blends results in the different carrier transport mobility of Alq3-rich and PVK-rich regions.     

Electric Field-Induced Quenching of Photoluminescence from Ir（PPY）3-Doped PVK

We study the photoluminescence (PL) and the PL dynamics of Ir(PPY)3-doped poly(N-vinylcarbazol) (PVK) under the modulation of an electric field. Tile results show that the electric-field-induced quenching of PL from Ir(PPY)3-doped PVK mainly comes from the dissociation of excitons in the chains of PVK. There is no significant difference in the excited state lifetime of Ir(PPY)3 to be observed under the different applied negative biases.Our experiments demonstrate that the excitons attached to the molecules of lr(PPY)3 are very stable.     

Effect of Annealing on Microstructure and Electrical Characteristics of Doped Poly （3-Hexylthiophene） Films

The effect of annealing on the microstructure and electrical characteristics of poly （3-hexylthiophene） （P3HT） films doped with very small amounts of the electron acceptor 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane （F4-TCNQ） is studied. X-ray diffraction and UV-vis spectrum studies show that unlike the pure P3HT film, the thermal treatment on the doped fihns under an Ar atmosphere can effectively enhance the crystalline order of P3HT films, as well as successfully facilitate the orientation of the polymer chains. This improvement is attributed to the electrostatic force between P3HT and F4-TCNQ molecules. This force induces the polymer chains to crystallize and orient during the annealing process. As a result, annealing significantly improves performance, especially for the Ion/Ioff ratio of the TFTs based on the doped P3HT films.     

Improved photoluminescence behavior of Eu3＋-activated Ca5（PO4）3F red nanophosphor by adding Li＋, Au3＋, and Bi3＋ as co-dopants

A series of Ca499（PO4）3F：1%Eu^3＋, 1%X （X = Li＋, Au3＋, and Bi3＋） nanoparticles are prepared using hydrothermal method, with an average size of 33-62 nm. We study the improved photoluminescence properties of Ca4.99（PO4）3F：1%Eu3＋ by co-doping with Li＋, Au3＋, and Bi3＋ ions, respectively, and the enhancement of the emission intensities of Eu3＋ is observed in these samples. The effects of Li＋ acting as a charge compensator, Au3＋ as a plasma surface sensitizer, and Bi3＋ as an energy conversion agent are discussed. The results show Ca4.99（PO4）3F：1%Eu3＋, 1%X nanoparticles are a promising candidate as a red component for near-ultraviolet light-emitting diodes.     

Improved Blue-Green Electrophosphorescence from a Tuning Iridium Complex with Benzyl Group in Polymer Light-Emitting Devices

Electroluminescence performances from a tuning biscyclometlated iridium complex with benzyl group are demonstrated in double-layered polymer light-emitting devices （PLEDs） using a blend of poly（9,9-dioctylfluorene） and 2-tert-butylphenyl-5-biphenyl-1,3,4-oxadiazole as a host matrix. Blue-green electrophosphorescent emission with a peak at 521 nm and a shoulder at 492nm was observed. The highest luminance efficiency of 4.8cd/A at current density of 0. 56 mA/cm^2 and a maximum luminance of 1944 cd/m^2 at 217.6 mA/cm^2 were achieved in the devices at the dopant concentration of 8%. The luminous performance of the devices becomes better with increasing dopant concentrations from 1% to 8%. This implies that the concentration quenching of this iridium complex with benzyl group can be efficiently inhibited in the devices.     

Efficient Solution-Processed Blue Electrophosphorescent Devices Based on a Novel Small-Molecule Host

Efficient blue small molecular phosphorescent fight-emitting diodes with a blue phosphorescent dye bis（3,5- difluoro-2-（2-pyridyl）-phenyl-（2-carboxypride） iridium （Ⅲ） （Flrpic） doped into a novel small-molecule host 9,9- bis[4-（3,6-di-tert-butylcarbazol-9-yl）phenyl] fluorene （TBCPF） as the light-emitting layer have been fabricated by spin-coating. The host TBCPF can form homogeneous amorphous films by spin-coating and has triplet energy higher than that of the blue phosphorescent dye Flrpic. All the devices with different Flrpic concentration in the emitting layer give emission from Flrpic indicating complete energy transfer from TBCPF to Flrpic. The device shows the best performance with a peak brightness of 8050 cd/m^2 at 10.2 V and the maximum current efficiency up to 3.52 cd/A, when the Flrpic doped concentration is as high as 16%.     

Efficient White Light Emission Using a Single Copolymer with Red and Green Chromophores on a Conjugated Polyfluorene Backbone Hybridized with InGaN-Based Light-Emitting Diodes

We report an efficient white-light emission based on a single copolymer/InGaN hybrid light-emitting diode. The single copolymer consists of a conjugated polyfluorene backbone by incorporating 2,1,3-benzothiadiazole （BT） and 4,7-bis（2-thienyl）-2,1,3-benzothiadiazole （DBT） as green and red light-emitting units, respectively. For the single copolymer/InGaN hybrid device, the Commission Internationale de 1＇Eclairage （CIE） coordinates, color temperature Tc and color rendering index Ra at 20mA are （0.323,0.329）, 5960K and 86, respectively. In comparison with the performance of red eopolymer PFO-DBT15 （DOF：DBT=85：15 with DOF being 9＇9- dioctylfluorene） and green copolymer PFO-BT35 （DOF：BT=-65：35） blend/InGaN hybrid white devices, it is concluded that the chemically doped copolymer hybridized device shows a higher emission intensity and spectral stability at a high driving current than the polymer blend.     

A New Conducting Polymer Electrode for Organic Electroluminescence Devices

Conducting polymer polydimethylsiloxane （PDMS） is studied for the high performance electrode of organic electroluminescence devices. A method to prepare the electrode consisting of a SiC thin film and PDMS is investigated. By using ultra thin SiC films with different thicknesses, the organic electroluminescence devices are obtained in an ultra vacuum system with the model device PDMS/SiC/PPV/Alq3, where PPV is poly para-phenylene vinylene and Alq3 is tris（S-hydroxyquinoline） aluminium. The capacitance voltage （C - V）, capacitance-frequency （C - F）, current-voltage （I - V）, radiation intensity-voltage （R - V） and luminance eFficiency-voltage （E - V） measurements are systematically studied to investigate the conductivity, Fermi alignment and devices properties in organic semiconductors. Scanning Kelvin probe measurement shows that the work function of PDMS/SiC anode with a 2.5-nm SiC over layer can be increased by as much as 0.28eV, compared to the conventional ITO anode. The result is attributed to the charge transfer effect and ohmic contacts at the interface.     

Polymer White-Light-Emitting Diodes with High Work Function Cathode Based on a Novel Phosphorescent Chelating Copolymer

Polymer white-light-emitting diodes are fabricated based on the blend of poly[9,9-di-（2-ethylhexyl）-fluorenyl-2, 7- diyl]-end capped with polysilsesquioxane （PFO） and a chelating copolymer of poly[（9,9-bis（3′-（N,N-dimethylamino） propyl）-2, 7-fluorene-alt-2, 7-（9,9-dioctylfluorene） ）-co- [2, 7-（9,9-dioctlyfluorene）-alt-5,5-bis（2-（4-methyl-l-naphtha- lene） pyridine-C^2,N） iridium （III） acethylacetonate]] （PFN-NaIr）. The device with the sole aluminium cathode is able to produce a comparably white electroluminescence efficiency of 1.31 cd/A to that of the device using low work function cathodes （such as Ba, Ca, etc.）. The CIE coordinates of the white light emission consisting of red, green and blue three components are nearly at （0.34, 0.35）. The mechanism of the white light emission from the device with the AI cathode is investigated, which is related to the efficient injection of electrons through the interface of PFN-Nalr/AI.     

Enhancement of Stability of Polymer Light-Emitting Diodes by Post Annealing

We investigate the effect of thermal annealing before and after cathode deposition on the stability of polymer light-emitting diodes （PLEDs） based on green fluorescent polyfluorene derivative. The annealed PLEDs exhibit improved charge transport and red-shift emission compared to the as-fabricated device. The stability of the PLEDs is largely enhanced by post-annealing before and after Ca deposition, which is attributed to the enhanced charge transport and the intimate contact between the cathode and the emissive layer.     

Efficient Top-Emitting Polymer Light-Emitting Diodes Using Chromium as Anode

We demonstrate a high eftlciency top-emitting polymer light-emitting diode （TPLED） with chromium （Cr） taking as the anode. The TPLED structure is Cr/poly-3, 4-ethylenedioxythiophene （PEDOT：PSS）/poly [2-（4-3＇,7＇- dimethyloctyloxy）-phenyl]-p-phenylenevinylene） （P-PP V） /Ba/Ag. The Cr （ 100 nm） anode is prepared by sputterdepositing in a vacuum chamber. It is found that the device emissive properties are affected dramatically by the thickness of both PEDOT：PSS and the Ag cathode. Optimized thicknesses of PEDOT：PSS and Ag layer are 60nm and 15nm, respectively. The diode exhibits excellent electroluminescence （EL） properties, such as a turn-on voltage of 3.32 V, luminous eftlciency of 4.41 cd/A and luminance of 6989cd/m^2 at driving voltage of about 9 V.     

Electroluminescence of a Multi-Layered Organic Light-Emitting Diode Utilizing Trans-4-[p-[N-methyl-N-(hydroxymethyl)amino]styryl]-N-Methylphridinium Tetraphenylborate as the Active Layer

Employing an organic dye salt of trans-4-[p-[N-methyl-N-(hydroxymethyl)amino]styryl]-N-methylphridinium tetra\-phenylborate (ASPT) as the active layer, 8-hydrocyquinoline aluminium (Alq₃) as the electron transporting layer and N,N’-diphenyl-N,N’-bis(3-methylphenyl)-[1,1’-biphenyl]-4,4’-diamine (TPD) as the hole transporting layer, respectively, we fabricate a multi-layered organic light-emitting diode and observe the colour tunable electroluminescence (EL). The dependence of the EL spectra on the applied voltage is investigated in detail, and the recombination mechanism is discussed by considering the variation of the hole-electron recombination region.     

Infrared electroluminescence from a Si MOS structure with Ge in the oxide

We report on room-temperature infrared electroluminescence (EL) from metal-oxide-semiconductor devices made from Si. We compare the luminescence from RF sputtered oxide films containing SiO₂ with and without Ge by using a composite target and luminescence from a SiO₂ layer made by rapid thermal oxidation. The sputtered films were annealed in the temperature range 600-900 °C. This densifies the films and is likely to reduce the concentration of defects. A luminescence peak located around 1150-1170 nm is observed at current densities as low as 0.1 A/cm². The corresponding photon energy is close to that of the Si band gap. In addition, we observe several broad luminescence bands in the range 1000-1750 nm. These bands get stronger with Ge in the SiO₂ film. Some of these bands have previously been suggested and are directly associated with Ge. Since we observe that the intensity is correlated with the presence of Ge while the mere presence of the bands is not, we discuss the EL bands being due to defects which concentration is influenced by Ge in the oxide.     

Enhanced luminance of organic light-emitting diodes with metal nanoparticle electron injection layer

Improvement of the performance of organic light-emitting diodes (OLEDs) was achieved by implementing Magnesium-Nickel nanoparticles at the cathode–organic interface using pulsed laser deposition technique. The small geometry of Mg-Ni nanoparticles acts to enhance the localized electric field around them, thus increasing electron injection through tunneling, from the cathode to the organic layer. Improved current and luminance characteristics were demonstrated for both small molecule and polymer-based OLEDs when the nanoparticle layer was incorporated.