Ductile Bulk Aluminum-Based Alloy with Good Glass-Forming Ability and High Strength

Based on a new approach for designing glassy alloy compositions, bulk Al-based alloys with good glass-forming ability （GFA） are synthesized. The cast Al86Si0.5Ni4.06Co2.94 Y6Sc0.5 rod with a diameter of i mm shows almost fully amorphous structure besides about 5% fcc-Al nucleated in the center of the rod. The bulk alloy with high Al concentration exhibits an ultrahigh yield strength of 1.18 GPa and maximum strength of 1.27 GPa as well as an obvious plastic strain of about 2.4% during compressive deformation. This light Al-based alloy with good GFA and mechanical properties is promising as a new high specific strength material with good deformability.     

非晶合金条带的爆炸焊接

 报道了利用爆炸焊接技术对铁基、铁镍基非晶合金条带（厚度约25 μm）进行单层和多层爆炸焊接的结果。金相分析结果表明，条带间相互结合良好；X光衍射结果说明，焊接后的条带仍保持非晶态，即使采用表面已有部分晶化德条带进行焊接，焊接后仍转化为非晶态。这说明在焊接过程中条带表面已发生熔化，且冷却速度也可达10⁶ K/s量级。     

In-Situ High Pressure Raman Spectrum and Electrical Property of PbMoO4

In-situ high pressure Raman spectra and electrical conductivity measurements of scheelite-structure compound PbMoO4 are presented. The Raman spectrum of PbMoO4 is determined up to 26.5 GPa on a powdered sample in a diamond anvil cell （DAC） under nonhydrostatic conditions. The PbMoO4 gradully experiences the trans- formation from the crystal to amorphous between 9.2 and 12.5 GPa. The crystal to amorphous transition may be due to the mechanical deformation and the crystalographic transformation. Furthermore, the electrical conductivity of PbMoO4 is in situ measured accurately using a microcircuit fabricated on a DAC based on the van der Pauw method. The results show that the electrical conductivity of PbMoO4 increases with increases of pressure and temperature. At 26.5 GPa, the electrical conductivity value of PbMoO4 at 295K is 1.93 - 10-4 S/cm, while it raises by one order of magnitude at 430K and reached 3.33 - 10-3 S/cm. However, at 430K, compared with the electrical conductivity value of PbMoO4 at 26.5 GPa, it drops by about two order magnitude at 7.4 GPa and achieves 2.81 × 10^-5 S/cm. This indicates that the effect of pressure on the electrical conductivity of PbMoO4 is more obvious than that of temperature.     

Cr对Fe-Zr基非晶合金电阻率及压力效应的影响

 在0.000 1~2.5 GPa范围不同静水压下，用四探针法详细测量了七种非晶态Fe_90-xCr_xZr₁₀合金（x=2、4、7、10、13、16、20）的电阻率。结果表明：（1）常压室温电阻率ρ₀与FeZr基非晶合金中Cr含量成N形曲线关系；（2）当静水压增加时，七种非晶合金的约化电阻率（ρ/ρ₀）都单调下降，x越大则电阻率下降的幅度越小；（3）非晶Fe_90-xCr_xZr₁₀合金电阻率的压力系数对x的变化相当敏感；（4）为方便查值，给出了六种典型静水压下ρ/ρ₀与x的曲线关系。最后，讨论了四种物理模型的选用以及相干交换散射在高压下的行为。     

Phase Diagram of Antiferromagnetically Exchange-Coupled Bilayer

Magnetic hysteresis properties of antiferromagnetically exchange-coupled bilayer structures, in which the two magnetic layers have different magnetic parameters and thicknesses, are studied within the framework of the Stoner-Wohlfarth model. Analytical expressions for the switching fields corresponding to the linear magnetic states are obtained. By adjusting the magnetic parameters or thicknesses of layers, nine different types of easy-axis hysteresis loops may exist. The phase diagram of easy-axis hysteresis loops is mapped in the k1 and k2 plane, where k1 and k2 are the ratios of magnetic anisotropy to the interlayer exchange coupling of the two magnetic layers, respectively.     

Magnetic Behaviour of Sm2Co7/Fe/Sm2 Co7, Nanocomposite Trilayers with Cr and Ti Additions

Trilayered Sm2Co7/Fe/Sm2Co7 spring exchange magnets are fabricated by dc magnetron sputtering on MgO substrates. Very thin layers （0.3-0.7 nm） of Cr and Ti are added at the interfaces of the two magnetic phases. The thickness of StucCo7 is kept at 20nm and Fe at 6nm while the thickness of Cr and Ti are varied as 0.3, 0.5, and 0.7nm. The base pressure of sputtering chamber is kept below 10^-7 Torr and Ar pressure at 3-8m Torr. The samples are characterized by x-ray diffraction （XRD） and SQUID magnetometer. We report improvement in exchange coupling of nonacomposite magnets by addition of thin layers of Cr at interfaces.     

A Modified Free Volume Model for Characterizing of Rate Effect in Bulk Metallic Glasses

We investigate the plastic deformation and constitutive behaviour of bulk metallic glasses （BMGs）. A dimensionless Deborah number DeiD = tr/ti is proposed to characterize the rate effect in BMGs, where tr is the structural relaxing characteristic time of BMGs under shear load, ti is the macroscopic imposed characteristic time of applied stress or the characteristic time of macroscopic deformation. The results demonstrate that the modified free volume model can characterize the strain rate effect in BMGs effectively.     

Structural and Magnetic Properties of [Fe/Ni]N Multilayers

[Fe/Ni]N multilayered structure grows epitaxially on the single crystalline MgO substrate. Due to the different directions of magnetic easy axes of Fe and Ni and the strong strain, large anisotropy dispersion is assumed. According to the layer model, the magnetization of Fe and Ni layers cannot follow each easy axis because of exchange coupling, and then the anisotropies are averaged out. The reduction of the effective anisotropy enhances with the decrease of periodic thickness. Thus, the coercivity of [Fe/Ni]N multilayers reduces with decreasing periodic thickness.     

Vortex Pinning due to Dynamic Spin-Vortex Interaction in aSuperconductor/Ferromagnet Multilayer

We investigate the mutual interaction between superconductivity and ferromagnetism in a Nb/Ni81 Ee19 multilayer by ac susceptibility measurements. Compared with a pure superconducting Nb film, the critical current density of the multilayer is apparently enhanced in a low magnetic field region but remains nearly the same in high magnetic fields, which indicates that a continuous ferromagnetic layer with in-plane magnetization can produce strong vortex pinning in a low field region. We interpret this unusual vortex-pinning phenomenon as a consequence of dynamic spin vortex interaction which induces a spin rotation following vortex movement. In addition, we propose that this dynamic interaction could be used for spin manipulation via a superconductor.     

Compression Behaviour of Bulk Metallic Glasses and Binary Amorphous Alloy

The compression properties of Zr41Ti14Cu12.aNi10Be22.5, Zr44.4Nb7Cu13.5Ni10.8Be24.3 bulk metallic glasses and Ni77P23 binary amorphous alloy are investigated at room temperature up to 24 GPa, 39 GPa and 30.5 GPa, respectively, using in-situ high pressure energy dispersive x-ray diffraction with a synchrotron radiation source. The pressure-volume relationship of Ni77P23 amorphous alloy is consistent well with the second order BirchMurnaghan （B-M） equation within the experimental pressure range. However, under higher pressure, the experimental data of Zr-based specimens deviate from the B-M equation. Compare to the binary amorphous alloy less excess free volume existing in the bulk metallic glass and multi-component atomic configuration results in a two-stage relationship between compressibility and pressure.     

单模激光系统中信噪比对净增益的随机共振

研究了受信号调制的色泵噪声和实虚部间关联的量子噪声驱动的单模激光系统的随机共振现象,发现信噪比随激光系统净增益系数存在随机共振.当泵噪声自关联时间和调制信号频率增加时,信噪比随激光系统净增益系数的变化曲线经历了从同时出现共振和抑制到单调上升的演化过程;当调制信号振幅、泵噪声强度和量子噪声强度、量子噪声实虚部间关联系数等变化时,该曲线一直同时出现共振和抑制,但共振峰和抑制谷有很大的变化.     

Microwave Absorption and Response Modeling of Nanocomposites Embedded SiC Nanoparticles

We study the mechanism of microwave response properties of SiCv/paraffin nanocomposites and propose a mi- crowave absorption model of nanocomposites based on the conservation law of energy and the theory of electro- magnetic scattering. Using the model we calculate the reflectivity of SiCp/paraffin nanocomposites ranging from 2 GHz to 18 GHz. The calculated results are very consistent with the experimental data in the frequency range investigated.     

Effect of Zr Addition on Glass-Forming Ability and Magnetic Properties of Fe-Nd-Al-B Alloys Prepared by Suction Casting

The microstructure and magnetic behaviors of the Fe-Nd-Al-B alloys prepared by suction casting with zirconium addition are investigated. With the small amount of zirconium addition, the magnetic properties of the alloys change from hard magnetic property to soft magnetic property. The proper addition of Zr （6%） not only improves the glass forming ability, but also suppresses the crystallization. From the scanning electron microscopy of the [（Fe0.53Nd0.37 Al0.10 ）0.96B0.04]94Zr6 alloy and the local average elemental compositions determined using energy dispersive spectroscopy analysis, the amorphous phase with a composition of Fe47Nd38Al12Zra in the alloy can be observed. The bulk amorphous Fe47Nd38Al12Zr3 alloy is prepared by suction casting exhibiting good glassforming ability and soft magnetic behavior.     

SbOx Thin Films Used for Write-Once Blue Laser Recording

SbOx thin films are deposited by reactive dc-magnetron sputtering from an antimony metal target in Ar＋O2 with the relative O2 content 7%. It is found that the as-deposited films can represent a two-component system comprising amorphous Sb and amorphous Sb2 O3. The crystallization of Sb is responsible for the changes of optical properties of the films. The results of the static test show that the SbOx thin films have good writing sensitivity for blue laser beams and the recording marks are very clear and circular. High reflectivity contrast of about 41% is obtained at a writing power 6mW and writing pulse width 300ns. In addition, the films show a good stability after reading 10000 times.     

A Charge-Trap Memory Device with a Composition-Modulated Zr-Silicate High-k Dielectric Multilayer Structure

We report a novel charge-trap memory device with a composition-modulated Zr-silicate high-k dielectric mul- tilayer structure prepared by using the pulsed laser deposition technique. The device employs amorphous （ZrO2）0.5（SiO2）0.5 as the tunneling and blocking oxide layers, and ZrO2 nanocrystals as the trapping storage layer. Zr02 nanocrystals are precipitated from the phase separation of （ZrO2）0.5（SiO2）0.2 films annealed at 800℃, and isolated from each other within the amorphous （ZrO2）0.5（SiO2）0.5 matrix. Our charge trapping device shows a memory window of 2.6 V and a stored electron density of 1×10^13/cm2.     

Temperature Dependence of Elastic Properties for Amorphous SiO2 by Molecular Dynamics Simulation

Large-scale and long-time molecular-dynamics simulations are used to investigate the temperature dependences of elastic properties for amorphous SiO2. The elastic moduli increase in a temperature range up to 1600 K and decrease thereafter. The anomalous behaviour in elasticity is explained by analysing the changes of atomic-scale structure with respect to increment of temperature. The mechanism originates predominantly from distortion of the SiO4 tetrahedra network in low-temperature ranges. At an elevated temperature range, thermal-induced Si-O bond stretching dominates the process and leads to normal temperature dependence of elastic properties.     

Influence of Rare-Earth Substitution for Iron in FeCrMoCB Bulk Metallic Glasses

The effects of rare earth addition on the glass forming ability of Fe50-xCr15Mo14C15B6Mx （x =0, 2 and M=Y, Gd） bulks and ribbons are studied. The thermal and structural properties of the samples are measured by a combination of differential scanning calorimetry （DSC）, x-ray diffraction and scanning electron microscopy. Chemical compositions are checked by energy dispersive spectroscopy analysis. The copper mold casting technique leads to a fully amorphous structure up to 2mm only for compositions containing Y or Gd. In the case of ribbons, a fully amorphous phase is observed for all the compositions. The roles of Y and Gd are discussed on the basis of melting behavior analyzed by high-temperature DSC. Such elements act as oxygen scavengers, avoiding heterogeneous nucleation.     

Dynamic Phase-Mapping of Domain Nucleation in MgO：LiNbO3 Crystal by Digital Holographic Interferometry

The quantitative phase-mapping of the domain nucleation in MgO：LiNbO3 crystals is presented by using the digital holographic interferometry. An unexpected peak phase at the beginning of the domain nucleation is observed and it is lowered as the spreading of the domain nucleus. The existence of the nucleus changes the moving speed of the domain wall by pinning it for 3 s. Such in-situ quantitative analysis of the domain nucleation process is a key to optimizing domain structure fabrication.     

Effect of dc-Joule-heating thermal processing on magnetoimpedance of Fe72Al5Ga2P11C6B4 amorphous alloy

The effect of multistep dc-Joule-heating thermal processing on magnetoimpedance (MI) of Fe₇₂Al₅Ga₂P₁₁C₆B₄ ribbons is presented. After material optimization significant increase of MI response up to value ΔZ/Z≈55% as well as sensitivity of about 6%/kA/m (for H?3–4 kA/m), were recorded in still amorphous samples at driving frequencies 2–3 MHz. On-line and post-annealing electrical resistivity together with Mössbauer spectra analysis and frequency dependence of the penetration depth were used for characterization of MI improvement.     

Room-Temperature Ferromagnetic ZnMnO Thin Films Synthesized by Plasma Enhanced Chemical Vapour Deposition Method

Room-temperature ferromagnetic Mn-doped ZnO films are grown on Si （001） substrates by plasma enhanced chemical vapour deposition （PECVD）. X-ray diffraction measurements reveal that the Znl-xMn.O films have the single-phase wurtzite structure. X-ray photoelectron spectroscopy indicates the existence of Mn^2＋ ions in Mndoped ZnO films. Furthermore, the decreasing additional Raman peak with increasing Mn-doping is considered to relate to the substitution of Mn ions for the Zn ions in ZnO lattice. Superconducting quantum interference device （SQUID） measurements demonstrate that Mn-doped ZnO films have ferromagnetic behaviour at room temperature.