浊点萃取-火焰原子吸收光谱法测定痕量铜

2-磺酸基-4-甲氧基苯基重氮氨基偶氮苯(MOSDAA)和Cu(II)反应生成疏水性络合物后,被萃取到Triton X-114非离子表面活性剂胶束相中,火焰原子吸收光谱法测定其中的铜,建立了浊点萃取预富集-火焰原子吸收光谱法测定铜的方法。反应体系的pH、MOSDAA和Triton X-114的浓度、平衡温度及时间等实验条件被优化。在选择的实验条件下,方法的检出限为1.1 ng/mL(3σ),对浓度为0.1μg/mL的Cu(II)溶液平行测定6次,相对标准偏差为1.9%。方法已用于小米和水样中痕量铜的测定。     

浊点萃取-火焰原子吸收光谱法测定食品和饮料中的痕量铜

研究了基于非离子表面活性剂TritonX-114和螯合剂二乙基氨基二硫代甲酸钠(DDTC)的浊点萃取-火焰原子吸收光谱法测定痕量铜的分析方法.考察了影响浊点萃取效率的参数,包括pH值、DDTC浓度、TritonX-114用量、平衡温度及时间等.在优化条件下,本法的检出限(3σ)为1.55μg/L,相对标准偏差RSD为3.4%(n=7,c=100μg/L),线性范围为0～250μg/L.将该法应用于茶叶标准样品(GBW07605)、奶粉和矿泉水等样品中痕量铜的测定,其回收率在96.7%～113.5%之间.     

浊点萃取-火焰原子吸收光谱法测定水样中痕量铜的研究

提出了浊点萃取火焰原子吸收光谱法测定痕量铜的新方法。详细探讨了溶液pH，试剂浓度等实验条件对浊点萃取及测定灵敏度的影响，在最佳下，富集50mL样品溶液，用火焰原子吸收光谱法测定，铜的检测限为0.35μg/L，铜的富集倍率为71倍。方法用于自来水、河水及海水中痕量铜的测定。     

浊点萃取-火焰原子吸收光谱法测定人尿液中的痕量铅

以双硫腙作为络合剂、聚乙二醇辛基苯基醚(TritonX-100)为非离子表面活性剂,建立浊点萃取-火焰原子吸收光谱测定尿液中痕量铅的方法。探讨了络合剂用量、平衡时间、pH值、TritonX-100用量、冰浴时间等因素对萃取效率的影响。结果表明:该方法对铅的最大富集倍数约为40倍,检出限为0.06μg·L-1(n=11)。回收率在96.7%~101%,线性范围为0~1.00μg·mL-1。利用该方法测定尿液中痕量铅的含量,结果令人满意。     

浊点萃取-火焰原子吸收光谱法测定矿渣中痕量金

研究了以双硫腙为络合剂,以非离子型表面活性剂Triton X-100为萃取剂的浊点萃取-火焰原子吸收光谱法(CPE-FAAS)测定痕量金(Ⅲ)的新方法。详细考察了溶液的pH值、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。该方法的线性范围为0.05~0.8μg/mL,检出限为7.9 ng/mL,相对标准偏差为4.12%(n=11),回收率在98.0%~102.0%之间,用于矿渣中金的测定,结果满意。     

浊点萃取-火焰原子吸收光谱法测定菠菜中镁、锌和铜

在pH 8.0缓冲溶液中,以8-羟基喹啉为螯合剂,镁、锌和铜均与8-羟基喹啉生成螯合物,加入Triton X-100表面活性剂用浊点萃取分离富集菠菜样品中镁、锌和铜。分取部分表面活性剂相用乙醇定容至25mL,所得溶液直接用火焰原子吸收光谱法进行测定。对影响浊点萃取的因素和共存离子的干扰等进行了试验并予以优化。镁、锌和铜的检出限(3s/k)依次为0.057,0.064,0.032mg.L-1。应用此法测定了大叶菠菜和小叶菠菜中3种元素的含量,在两种样品中用标准加入法进行方法的回收试验,测得镁的回收率在93.3%～100.5%之间;锌的回收率在91.7%～97.9%之间;铜的回收率在94.0%～107.1%之间。     

浊点萃取-火焰原子吸收光谱法测定催化剂中痕量钯的研究

研究了以1-（2-吡啶偶氮）-2-萘酚（PAN）为络合剂,以非离子型表面活性刺Triton X-100为萃取剂的浊点萃取分离富集-火焰原子吸收光谱法测定痕量钯的新方法。详细考察了溶液的pH、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。该方法对钯的检出限为30．8ng／mL,相对标准偏差（RSD）为2．1％（n=10）,回收率在97．8％-106．6％之间。可用于催化剂中Pd（Ⅱ）的测定。     

浊点萃取预富集火焰原子吸收光谱法测定水样中痕量钴

本文提出了浊点萃取预富集火焰原子吸收光谱法测定痕量钴的新方法。详细研究了溶液pH值、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。在优化的实验条件下,本法对钴的富集倍数为20倍,检出限为3．28ng／mL,相对标准偏差(RSD)为4．1％(n=10)。所建立的方法用于自来水、湖水中痕量钴的测定,分析结果满意。     

浊点萃取-火焰原子吸收光谱法测定淡水鱼中痕量铅

采用以双硫腙为络合剂、Triton X-100为表面活性剂的新型浊点萃取体系富集淡水鱼中的痕量铅,并用火焰原子吸收光谱法对其进行测定。探讨了溶液pH、表面活性剂浓度、络合剂用量、平衡温度、平衡时间等对浊点萃取及测定灵敏度的影响,优化了实验条件。在最佳条件下测得铅的检出限为0.090μg/L,校准曲线相关系数为0.9999。该方法已用于淡水鱼中痕量铅的测定。     

浊点萃取-火焰原子吸收光谱法测定某些中药中的铜含量

浊点萃取(Cloud Point Extraction,CPE)是近年来出现的一种新兴的环保型的液-液萃取技术,它不使用挥发性有机溶剂,对环境的影响较小[1].它以中性表面活性剂胶束水溶液的溶解性和浊点现象为基础,通过改变试验参数如溶液pH值、温度等引发相分离,将疏水性物质与亲水性物质分离.它具有经济、安全、高效、简便等优点,已广泛应用于生命科学和环境科学研究中[2-4],特别是在痕量金属元素的分离富集方面取得了很大的成功[5-7].     

浊点萃取-原子吸收光谱法测定塑料中的痕量铜

建立了以1-(2-吡啶偶氮)-2-萘酚(PAN)为络合剂、Triton X-100为表面活性剂的浊点萃取-原子吸收光谱法测定痕量铜的分析方法。探讨了溶液的pH、络合剂和表面活性剂用量、平衡温度和平衡时间等因素对浊点萃取的影响。最佳条件下,线性方程为Y=0.1049X+0.0016,相关系数为0.9988,检出限为0.7μg/L,相对偏差为2.3%,富集倍数为15倍。用该方法对几种塑料制品中的痕量铜进行测定,回收率为97.5%～101.9%。     

Determination of copper in water samples by atomic absorption spectrometry after cloud point extraction

Cloud point extraction employing the new reagent 6-[2′-(6′-methyl-benzothiazolylazo)]-1,2-dihydroxy-3,5-benzenedisulfonic acid as complexing agent and Triton X-114 as the surfactant is proposed for copper determination. A sample volume of 10 mL was used. Dilution of the surfactant-rich phase with acidified methanol was performed after phase separation, and the copper contents were measured by flame atomic absorption spectrometry. Variables affecting the system were optimized using factorial design and Doehlert matrix. Signals were measured as peak height using an instrument software. Using the experimental conditions defined in the optimization, the method allowed copper determination with a detection limit of 1.5 μg L⁻¹. The calculated enrichment factor is 14. The effects of foreign ions are reported. The accuracy of the procedure was tested by analyzing certified reference material. The method was successfully applied to copper determination in natural and drinking water samples.     

Determination of trace vanadium in soil by cloud point extraction and graphite furnace atomic absorption spectroscopy

This work describes a new analytical procedure for trace vanadium by graphite furnace atomic absorption spectroscopy coupled to cloud point extraction (CPE) as the separation-preconcentration method. The CPE behavior of vanadium using methylene blue as complex agent and Triton X-100 as a surfactant was investigated systematically. Under the optimized conditions, the detection limit was 0.7 ng · mL⁻¹, and the relative standard deviation was 4.3% for vanadium (c = 50.0 ng · mL⁻¹, n = 5). The recovery of vanadium was in the range of 98.9–102.8%. The method was applied to the analysis of vanadium in certified reference materials and real samples. The results obtained were in good agreement with the certified values. Correspondence: Xiashi Zhu, Key Laboratory of Environmental Material and Environmental Engineering of Jiangsu province/College of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002, P.R. China     

Determinaton of trace amounts of titanium by flame atomic absorption spectrometry after cloud point extraction

In this work a cloud-point extraction has been used for the preconcentration of the trace amounts of titanium after complex formation with morin (2′,3,4′,5,7-pentahydroxyflavone) using Triton X-114 as surfactant. The chemical variables affecting the phase separation and the viscosity affecting the detection by flame atomic absorption spectrometry (FAAS) were optimized. At pH 4.5, preconcentration of 50 mL of sample in the presence of 0.08% Triton X-114 and 1.0 × 10^?4 M morin enabled the detection limit (c _L = 3S _b/m) of 2.9 ng/mL titanium and linear range 0.02–2.0 μg/mL to be achived. The preconcentration factor was 61, and the relative standard deviation was 3.8% for 0.1 μg/mL solution of Ti(IV) by repeated assays (n = 9). The proposed method has been applied to the determination of titanium in well water, spiked water and plant (Haloxylon).     

磁性聚电解质多层膜固相萃取-火焰原子吸收光谱法测定水样中的三价铬

将聚电解质多层膜组装于磁性硅胶表面得到新型吸附剂;将该新型吸附剂用于磁性固相萃取(MSPE),并与火焰原子吸收光谱检测联用分析水样中的Cr3+;优化了样品的pH、洗脱条件和超声时间等影响MSPE萃取效率的参数.结果表明,在优化的测试条件下,该方法的检出限(3σ)为1.7μg·L-1,相对标准偏差为2.1%,富集倍数为15.9,可用于测定合成水样中的Cr3+.     

Determination of ultra trace amounts of bismuth in biological and water samples by electrothermal atomic absorption spectrometry (ET-AAS) after cloud point extraction

A new approach for a cloud point extraction electrothermal atomic absorption spectrometric method was used for determining bismuth. The aqueous analyte was acidified with sulfuric acid (pH 3.0-3.5). Triton X-114 was added as a surfactant and dithizone was used as a complexing agent.After phase separation at 50 °C based on the cloud point separation of the mixture, the surfactant-rich phase was diluted using tetrahydrofuran (THF). Twenty microliters of the enriched solution and 10 μl of 0.1% (w/v) Pd(NO₃)₂ as chemical modifier were dispersed into the graphite tube and the analyte determined by electrothermal atomic absorption spectrometry. After optimizing extraction conditions and instrumental parameters, a preconcentration factor of 196 was obtained for a sample of only 10 ml. The detection limit was 0.02 ng ml⁻¹ and the analytical curve was linear for the concentration range of 0.04-0.60 ng ml⁻¹. Relative standard deviations were <5%.The method was successfully applied for the extraction and determination of bismuth in tap water and biological samples (urine and hair).