硫敏化中心中的银原子簇的增感作用

采用一定电位范围内的氧化还原缓冲液处理单分散立方溴化银乳剂颗粒表面上的硫敏化中心和由曝光生成的潜影中心,考察银原子簇的漂白和再生后的曝光响应曲线.实验结果再一次确认硫敏化中心中存在的银原子簇对硫敏化起重要作用,而且敏化效果也与银原子簇的含量有关.为此,提出硫敏化中心是由硫化银簇与银簇组成,它们在潜影形成的过程中各起不同的作用,但都有利于提高潜影的生成效率,因而共同产生敏化效应.     

感光乳剂敏化中心的平衡电极电势在化学成熟过程中的变化

本文用改进的Reinders方法研究了硫、金和还原敏化的感光乳剂在化学成熟过程中敏化中心平衡电极电势的变化,并对这些感光乳剂层内敏化中心的抗氧化性进行了比较研究。 实验结果表明:在化学成熟过程中,敏化中心的平衡电极电势的变化与感光层光敏度的变化趋势极为相似。金敏化乳剂中,在化学成熟最佳时生成的敏化中心比成熟初期生成的敏化中心不易氧化。还原敏化产生的敏化中心较稳定。文中根据Чибисов的化学敏化理论对实验结果进行了讨论。     

碱性介质中葡萄糖在铂电极上的阳极氧化

为了进一步探明葡萄糖在铂电极上的氧化机理,用循环伏安法(CV)在-0.9～0.4 V(相对于饱和甘汞参比电极)内研究了葡萄糖在铂电极上催化氧化行为,首次详细报道了葡萄糖在电化学氧化过程中的电位振荡现象,并用电流扫描法表征了葡萄糖的电位振荡情况.电流扫描结果表明,在较慢的电流扫描速度下,电极过程出现了明显的电位振荡.说明电极上产生了毒化中间物,电位振荡是由于毒化中间物在电极上的吸附和在高电位下氧化除去引起的.     

聚四氨基钴酞菁膜修饰电极对甲巯咪唑的电催化氧化

用循环伏安法(CV)研究了聚四氨基钴酞菁(CoTAPc)膜修饰电极(p-CoTAPc CME)对甲巯咪唑的电催化氧化行为.在pH=2的缓冲溶液中,与未修饰玻碳电极(GC)相比,甲巯咪唑在p-CoTAPc CME(GC基体)上的氧化峰电位(Vpa)负移220 mV左右,峰电流(Ipa)变为原来的3倍多;还原峰电位(Vpc)正移大约223 mV,峰电流(Ipc)几乎变为裸电极时的6倍.同时,p-CoTAPc CME对甲巯咪唑的电催化氧化活性有很高的稳定性.     

聚L-赖氨酸修饰电极循环伏安法测定药剂中的多巴胺

用循环伏安法制备了聚L-赖氨酸修饰玻碳电极,研究多巴胺在聚L-赖氨酸修饰电极上的电化学行为,建立了循环伏安法测定多巴胺的新方法。实验结果表明,在pH7.0的磷酸盐缓冲溶液中,扫描速率为150mV/s,循环扫描电位在-0.3~0.6V时,多巴胺在聚L-赖氨酸修饰玻碳电极上出现一对灵敏的氧化还原峰,峰电位分别为Epa=0.175V,Epc=0.146V(相对饱和甘汞电极);测定多巴胺的线性范围为1.0×10-3~1.0×10-5mol/L和1.0×10-5~8.0×10-9mol/L,方法检出限1.0×10-9mol/L。用于药剂中多巴胺的测定。     

硫堇衍生化自组装膜修饰金电极的电化学性质及其对抗坏血酸的电催化氧化

将硫堇共价键合到自组装在金电极表面的半胱胺单分子层上,制成了衍生化自组装单分子膜修饰电极,并用电化学方法研究了它的电化学性质.循环伏安图显示其在pH＝7.7的磷酸盐缓冲液中,于－0.45～＋0.50V(vs.SCE)范围内有2对氧化还原峰.峰电位分别为E_pa¹＝214mV。E_pc¹＝82mV,E_pa2＝－75mV,E_pc2＝－160mV(vs.SCE).pH在5.0～9.0范围内,峰1有2个质子参与反应,峰2有1个质子参与反应.它的表面电子转移速率常数k_s＝0.02S^－1.此膜对抗坏血酸的氧化有催化作用,其氧化过电位较在裸金电极上降低了约250mV.催化电流与抗坏血酸的浓度在1.0×10^-6～4.0×10^-3mol/L范围内呈良好的线性关系.抗坏血酸催化氧化的异相速率常数为2.68×10^-3cm/s.     

肉桂酸修饰电极同时测定多巴胺和抗坏血酸的研究

用电化学聚合方法制备肉桂酸(CA)修饰的玻碳电极(PCA/GC),研究多巴胺(DA)和抗坏血酸(AA)在修饰电极上的电化学行为.结果表明,在DA和AA共存体系中,DA、AA在PCA/GC电极上氧化峰电流增大且氧化峰电位相差200 mV,据此可同时检测DA和AA.在pH 7.0磷酸盐缓冲液中,DA和AA的氧化峰电流与其浓...     

碳基针孔组合微电极的性能测试与理论验证

在涂敷绝缘漆的碳电极上，用针尖刺穿绝缘膜，形成组合微盘电极.在铁氰化钾与亚铁氰化钾溶液体系测得电极的循环伏安曲线与理论计算曲线十分吻合.阶梯扫描伏安法测得的极限扩散电流，与亚铁氰化钾浓度和扫描速率平方根都成良好的线性关系.在氯化钾支持电解质溶液中，测得Cd(Ⅱ)的循环伏安曲线是不可逆的， Cd(Ⅱ)的还原波峰电位在－0.98 V（相对于饱和甘汞电极）附近； 800 mV•s－1阶梯扫描速率下，在2.55×10－5 ～1.28×10－4 mol•dm－3浓度范围内， Cd(Ⅱ)的浓度与还原波峰电流成良好的线性关系.     

两亲型多吡啶钌(II)染料的合成及其在染料敏化太阳电池中的应用

合成了两亲型多吡啶钌(II)配合物：顺式-二异硫氰根(4,4'-二叔丁基-2,2’-联吡啶)(4,4’-二羧酸-2,2’-联吡啶)合钌(II)(K005)，并用循环伏安法、核磁共振氢谱、紫外－可见吸收光谱、傅立叶变换红外光谱等对其进行了表征。该配合物在537和418 nm处有强的金属－配体电荷转移吸收带，可以在很宽带光谱范围内对纳米二氧化钛薄膜进行敏化。对K005染料的光物理和光化学性能和著名的N3染料和两亲型染料Z907进行了对比。通过循环伏安测试，观察到了一对可逆氧化还原电对，其阳极峰电位和阴极峰电位差0.08 V，半波电位为0.725 V(相对于饱和甘汞电极)，这个电对归属于RuII/III的氧化还原。这个配合物成功用作染料敏化太阳电池的敏化剂，在未对二氧化钛薄膜和电解质进行优化时，在AM 1.5，100 mW cm-2的太阳辐照下，获得了3.72%的光电转换效率。     

聚乙撑二氧噻吩修饰电极的电化学行为及对抗坏血酸的电催化作用

研究了聚乙撑二氧噻吩修饰电极在水溶液中的电化学行为及对抗坏血酸的电催化作用,实验表明抗坏血酸在聚乙撑二氧噻吩修饰电极上的氧化峰电位为+0.23V,较其在铂电极上的氧化峰电位负移220mV.在1.0×10^-1～1.0×10^-1mol/L浓度范围内,峰电流和抗坏血酸的浓度有线性关系,可用于水果等样品中抗坏血酸的测定。     

Sabatier效应机理的研究

通过对核壳乳剂以及均质乳剂潜影分布和sabatier效应的研究,提出了产生Sabatier效应的可能机理:第一次曝光产生的表面潜影吸附了显影剂负离子以后变成空穴捕获中心而在第二次曝光时被漂白造成影像反转;卤化银颗粒上必须同时有足够的表面敏化中心和足够的内部敏化中心,两者应相匹配。利用这个机理可以解释许多有关Sabatier效应的实验现象。     

Direct electrochemistry of glucose oxidase in a colloid Au-dihexadecylphosphate composite film and its application to develop a glucose biosensor

Colloid Au (Au(nano)) with a diameter of about 10 nm was prepared and used in combination with dihexadecylphosphate (DHP) to immobilize glucose oxidase (GOD) onto the surface of a graphite electrode (GE). The direct electrochemistry of GOD confined in the composite film was investigated. The immobilized GOD displayed a pair of redox peaks with a formal potential of -0.475 mV in pH 7.0 O(2)-free phosphate buffers at scan rate of 150 mV s(-1). The GOD in the composite film retained its bioactivity and could catalyze the reduction of dissolved oxygen. Upon the addition of glucose, the reduction peak current of dissolved oxygen decreased, which could be developed for glucose determination. A calibration linear range of glucose was 0.5-9.3 mM with a detection limit of 0.1 mM and a sensitivity of 1.14 microA mM(-1). The glucose biosensor showed good reproducibility and stability. The general interferences that coexisted in human serum sample such as ascorbic acid and uric acid did not affect glucose determination.     

Redox protein-polymer films for simultaneous determination of ascorbic Acid and hydrogen peroxide

Layer by layer films of protein and redox polymer were constructed and used to simultaneously analyze ascorbic acid and hydrogen peroxide. The films were made using hemoglobin and poly[4-vinylpyridine Os(bipyridine)(2)Cl]-co-ethylamine (Pos-Ea). The film growth was monitored using cyclic voltammetry, quartz crystal microbalance (QCM) and atomic force microscopy (AFM). Reversible pairs of oxidation-reduction peaks were observed using cyclic voltammetry corresponding to the Os(II)/Os(III) from redox polymer and HbFe(III)/HbFe(II) redox couples at 0.35 and -0.25 V vs. Ag/AgCl, respectively. The two redox centers were independent of each other. This enabled the simultaneous and independent determination of ascorbic acid and hydrogen. Peak currents were linearly related to concentration for both analytes in a mixture. The linear range of ascorbic acid was 0 - 1 mM (R(2) = 0.9996, n = 5) at scan rate of 50 mV s(-1) (sensitivity 3.5 microA/mM) while hydrogen peroxide linear range was 1.0 - 10.0 microM (R(2) = 0.991, n = 6) with sensitivity of 1.85 microA/microM.     

稳盐(TAI)对立方体溴碘化银微晶中显影中心分布影响的研究

本文应用微机控制的双注仪制备了碘含量为2.5%的立方体溴碘化银乳剂微晶,应用控制显影技术和电子显微镜研究了稳盐(TAI)对乳剂微晶显影中心大小和分布的影响。结果表明:TAI对S+Au增感的立方体溴碘化银乳剂微晶有明显的增感作用,而对未经化学增感的乳剂没有明显的增感作用。TAI使S+Au增感的乳剂含一个和两个显影中心的颗粒数增加。     

Application of 2-(3,4-dihydroxyphenyl)-1,3-dithialone self-assembled monolayer on gold electrode as a nanosensor for electrocatalytic determination of dopamine and uric acid

The electrooxidation of dopamine (DA), uric acid (UA) and their mixture on a gold electrode modified by a self-assembled monolayer of 2-(3,4-dihydroxyphenyl)-1,3-dithialone has been studied by cyclic voltammetry (CV), chronoamperometry and differential pulse voltammetry (DPV). CV was used to investigate the redox properties of the modified electrode at various scan rates and the apparent charge transfer rate constant (k(s)), and transfer coefficient (α) were calculated. The mediated oxidation of DA at the modified electrode under the optimum condition (pH = 7.0) in CV occurs at a potential about 220 mV less positive than that of the unmodified gold electrode. The values of electron transfer coefficients (α), catalytic rate constant (k) and diffusion coefficient (D) were calculated for DA, using electrochemical methods. DPV exhibited a linear dynamic range over the concentration range of 0.2-250.0 μM and a detection limit (3σ) of 0.07 μM for DA. The modified electrode was used for simultaneous determination of DA and UA by DPV. The results showed that the electrode is highly efficient for the catalytic electrooxidation of DA and UA, leading to a remarkable peak resolution (~350 mV) for two compounds. The electrode was used for the determination of DA in an injection sample.     

Electrochemically triggered Michael addition on the self-assembly of 4-thiouracil: generation of surface-confined redox mediator and electrocatalysis

Generation of a surface-confined redox mediator (RM) by an electrochemically triggered Michael addition reaction and the electrocatalytic properties of the mediator are described. Electrogenerated o-quinone undergoes Michael addition reaction with the self-assembled monolayer (SAM) of 4-thiouracil (4-TU) on a gold (Au) electrode and yields a surface-confined RM, 1-(3,4-dihydroxyphenyl)-4-mercapto-1H-pyrimidin-2-one (DPTU). The Michael addition reaction depends on the electrolysis potential and time, solution pH, and concentration of catechol (CA) used in the reaction. The redox mediator, DPTU, exhibits reversible redox response, characterstic of a surface-confined species at approximately 0.22 V in neutral pH. The anodic peak potential of DPTU shifts by 58+/-2 mV while changing the solution pH by one unit, suggesting that protons and electrons taking part in the redox reaction are in the ratio of 1:1. The apparent rate constant (ksapp) for the heterogeneous electron-transfer reaction of the RM was determined to be 114+/-5 s-1. The surface coverage (Gamma) of DPTU on the electrode surface was 8.2+/-0.1x10(-12) mol/cm2. DPTU shows excellent electrocatalytic activity toward oxidation of reduced nicotinamide adenine dinucleotide (NADH) with activation overpotential, which is approximately 600 mV lower than that observed at the unmodified Au electrode. The dipositive cations in the supporting electrolyte solution amplify the electrocatalytic activity of DPTU. A 2.5-fold enhancement in the catalytic current was observed in the presence of Ca2+ or Ba2+ ions. The sensitivity of the electrode toward NADH in the presence and absence of Ca2+ ions was 0.094+/-0.011 and 0.04+/-0.0071 nA cm-2 nM-1, respectively. A linear increase in the catalytic current was obtained up to the concentration of 0.8 mM, and the electrode can detect amperometrically as low as 25 nM of NADH in neutral pH.     

New π-Conjugated Ferrocenyl-Substituted Heterocyclic Systems Containing Electron-Deficient Aromatic Nitrogen Heterocycles

A series of ferrocenyl-substituted methyl ketones and chalcones were synthesized and converted to unsymmetrical 4,6-disubstituted pyrimidin-2-amines and 2-(1H-pyrrol-1-yl)pyrimidines in which the ferrocene fragment is separated from the pyrimidine ring by π-deficient (pyridine) or π-excessive (thiophene) heterocycle. The forbidden band gap of the obtained compounds was determined on the basis of their UV spectra (\(E_{\text{g}}^{\text{opt}}\) = 1.75?2.36 eV), and their electrochemical properties were studied. The presence of a thiophene ring between the ferrocene and pyrimidine fragments reduces the redox potential of the ferrocene fragment (20?30 mV), whereas pyridine spacer between the ferrocene and pyrimidine fragment increases the redox potential of the ferrocene fragment by more than 100 mV.     

Redox-active star molecules incorporating the 4-benzoylpyridinium cation: implications for the charge transfer efficiency along branches vs across the perimeter in dendrimers

We report the redox properties of four star systems incorporating the 4-benzoyl-N-alkylpyridinium cation; the redox potential varies along the branches but remains constant at fixed radii. Bulk electrolysis shows that at a semi-infinite time scale all redox centers are electrochemically accessible. However, voltammetric analysis (cyclic voltammetry and differential pulse voltammetry) shows that only two of the three redox-active centers in the perimeter are electrochemically accessible during potential sweeps as slow as 20 mV s-1 and as fast as 10 V s-1. On the contrary, both redox centers along branches are accessible electrochemically within the same time frame. These results are explained in terms of slow through-space charge transfer and the globular 3-D folding of the molecules and are discussed in terms of their implications on the design of efficient redox functional dendrimers.     

Amperometric urea biosensor based on urease and electropolymerized toluidine blue dye as a pH-sensitive redox probe

The electropolymerized toluidine blue film deposited on the glassy carbon electrode show amperometrically detectable pH sensitivity. This feature of polytoluidine blue (PTOB) film was used for a construction of an amperometric urea biosensor. We have observed a linear shift of the formal redox potential with increasing pH value between 4 and 8 giving the slope of 81 mV(Delta) pH(-1). Polytoluidine blue film has had a significantly increased stability and higher electrochemical activity compared to the adsorbed monomeric dye. The polytoluidine blue urea biosensor has been operating at a working potential of -200 mV vs. SCE. The sensitivity of the biosensor was 980 nA mM(-1) cm(-2). The biosensor showed linearity in concentration range up to 0.8 mM with the detection limit of 0.02 mM (S/N=3).