AN ADAPTIVE FINITE ELEMENT METHOD FOR A TWO-EQUATION TURBULENCE MODEL IN WALL-BOUNDED FLOWS

This paper presents an adaptive finite element method for solving incompressible turbulent flows using a k–ϵ model of turbulence. Solutions are obtained in primitive variables using a highly accurate quadratic finite element on unstructured grids. A projection error estimator is presented that takes into account the relative importance of the errors in velocity, pressure and turbulence variables. The efficiency and convergence rate of the methodology are evaluated by solving problems with known analytical solutions. The method is then applied to turbulent flow over a backward-facing step and predictions are compared with experimental measurements. © 1997 John Wiley & Sons, Ltd.     

Two-equation (k, ϵ) turbulence computations by the use of a finite element model

A finite element technique is presented and applied to some one- and two-dimensional turbulent flow problems. The basic equations are the Reynolds averaged momentum equations in conjunction with a two-equation (k, ?) turbulence model. The equations are written in time-dependent form and stationary problems are solved by a time iteration procedure. The advection parts of the equations are treated by the use of a method of characteristics, while the continuity requirement is satisfied by a penalty function approach. The general numerical formulation is based on Galerkin's method. Computational results are presented for one-dimensional steady-state and oscillatory channel flow problems and for steady-state flow over a two-dimensional backward-facing step.     

Derivation of a second-order model for Reynolds stress using renormalization group analysis and the two-scale expansion technique

With the two-scale expansion technique proposed by Yoshizawa,the turbulent fluctuating field is expanded around the isotropic field.At a low-order two-scale expansion,applying the mode coupling approximation in the Yakhot-Orszag renormalization group method to analyze the fluctuating field,the Reynolds-average terms in the Reynolds stress transport equation,such as the convective term,the pressure-gradient-velocity correlation term and the dissipation term,are modeled.Two numerical examples:turbulent flow past a backward-facing step and the fully developed flow in a rotating channel,are presented for testing the efficiency of the proposed second-order model.For these two numerical examples,the proposed model performs as well as the Gibson-Launder (GL) model,giving better prediction than the standard k-ε model,especially in the abilities to calculate the secondary flow in the backward-facing step flow and to capture the asymmetric turbulent structure caused by frame rotation.     

Introduction of turbulent model in a mixed finite volume/finite element method

The aim of this work is to present a new numerical method to compute turbulent flows in complex configurations. With this in view, a k-? model with wall functions has been introduced in a mixed finite volume/finite element method. The numerical method has been developed to deal with compressible flows but is also able to compute nearly incompressible flows. The physical model and the numerical method are first described, then validation results for an incompressible flow over a backward-facing step and for a supersonic flow over a compression ramp are presented. Comparisons are performed with experimental data and with other numerical results. These simulations show the ability of the present method to predict turbulent flows, and this method will be applied to simulate complex industrial flows (flow inside the combustion chamber of gas turbine engines). The main goal of this paper is not to test turbulence models, but to show that this numerical method is a solid base to introduce more sophisticated turbulence model.     

Finite element solutions for laminar and turbulent compressible flow

The time-split finite element method is extended to compute laminar and turbulent flows with and without separation. The examples considered are the flows past trailing edges of a flat plate and a backward-facing step. Eddy viscosity models are used to represent effects of turbulence. It is found that the time-split method produces results in agreement with previous experimental and computational results. The eddy viscosity models employed are found to give accurate predictions in all regions of flow except downstream of reattachment.     

Numerical modeling of the self-oscillation onset near a three-dimensional backward-facing step in a transonic flow

The results of a numerical investigation of the nature of self-oscillation processes occurring in transonic flow past a backward-facing step and a cavity with a flow of the open type are presented. The turbulent flow past the above-mentioned bodies is modeled using the NOISEtte software package intended for solving problems of aerodynamics and aeroacoustics on unstructured grids. The modeling is performed using the eddy-resolving IDDES method that belongs to the class of hybrid RANS-LES approaches. The adequacy of the calculations is confirmed by means of comparing the results obtained with the available experimental data. The structure and the salient features of the self-oscillatory, hydrodynamic-in-nature process, which arises in flow past a cavity and a backward-facing step, are established.     

Finite element solution of the streamfunction-vorticity equations for incompressible two-dimensional flows

The streamfunction-vorticity equations for incompressible two-dimensional flows are uncoupled and solved in sequence by the finite element method. The vorticity at no-slip boundaries is evaluated in the framework of the streamfunction equation. The resulting scheme achieves convergence, even for very high values of the Reynolds number, without the traditional need for upwinding. The stability and accuracy of the approach are demonstrated by the solution of two well-known benchmark problems: flow in a lid-driven cavity at Re ? 10,000 and flow over a backward-facing step at Re = 800.     

Measuring turbulence energy with PIV in a backward-facing step flow

Turbulence energy is estimated in a backward-facing step flow with three-component (3C, stereo) particle image velocimetry (PIV). Estimates of turbulence energy transport equation for convection, turbulence transport, turbulence production, viscous diffusion, and viscous dissipation in addition to Reynolds stresses are computed directly from PIV data. Almost all the turbulence energy terms in the backward-facing step case can be measured with 3C PIV, except the pressure-transport term, which is obtained by difference of the other turbulence energy terms. The effect of the velocity spatial sampling resolution in derivative estimations is investigated with four two-dimensional PIV measurement sets. This sampling resolution information is used to calibrate the turbulence energies estimated by 3C PIV measurements. The focus of this study is on the separated shear layer of the backward-facing step. The measurements with 3C PIV are carried out in a turbulent water flow at Reynolds number of about 15,000, based on the step height h and the inlet streamwise maximum mean velocity U₀. The expansion ratio (ER) is 1.5. Turbulence energy budget profiles in locations x/h=4, x/h=6, and x/h=10 are compared with DNS data of a turbulent flow. The shapes of profiles agree well with each other. Different ERs between the PIV case (1.5) and the DNS case (1.2) cause higher values for the turbulence energies measured by PIV than the energies by DNS when x/h=10 is approached. PIV results also show that the turbulence energy level in these experiments is generally higher than that of the DNS data.     

Turbulent mixed convection flow over a backward-facing step––the effect of the step heights

Effect of the backward-facing step heights on turbulent mixed convection flow along a vertical flat plate is examined experimentally. The step geometry consists of an adiabatic backward-facing step, an upstream wall and a downstream wall. Both the upstream and downstream walls are heated to a uniform and constant temperature. Laser–Doppler velocimeter and cold wire anemometer were used, respectively, to measure simultaneously the time-mean velocity and temperature distributions and their turbulent fluctuations. The experiment was carried out for step heights of 0, 11, and 22 mm, at a free stream air velocity, u_∞, of 0.41 m/s, and a temperature difference, ΔT, of 30 °C between the heated walls and the free stream air. The present results reveal that the turbulence intensity of the streamwise and transverse velocity fluctuations and the intensity of temperature fluctuations downstream of the step increase as the step height increases. Also, it was found that both the reattachment length and the heat transfer rate from the downstream heated wall increase with increasing step height.     

Experimental study of the separated flow structure behind a backward-facing step and a passive disturbance

The flow in a channel with a backward-facing step and a rib mounted upstream of the step and generating flow disturbances is studied experimentally by the method of particle image velocimetry. It is demonstrated that mounting of a single rib leads to deformation of the profiles of the mean streamwise velocities and turbulent fluctuations. The effect of the position and height of a single rib on the recirculation region behind the backward-facing step is analyzed. Reduction of the recirculation region size behind the step in the case of flow reattachment upstream of the step is validated.     

The calculation of incompressible separated turbulent boundary layers

The algebraic turbulent model of Baldwin and Lomax was incorporated into the incompressible full Navier–Stokes code FIDAP. This model was extensively tested in the past in finite difference codes. We believe that the incorporation of the model also into the finite element code has resulted in a practical method to compute a variety of separated turbulent 2D flows. Firstly, we use the model to compute the attached flow about an aerofoil. Next, the application of the model to separated flows is presented by computing the flows at high angles of attack up to maximum lift. It is shown that the model is capable of predicting separation, steady stall and C_Lmax. As a difficult test of the model we compute the laminar separation bubble development directly using the full Navier–Stokes finite element code. As far as we know, this approach has not yet been reported. The importance of using an appropriate upwinding is discussed. When possible, comparison of computed results with experiments is presented and the agreement is good.     

后台阶流动再附着过程的大涡模拟研究

应用自主开发的大涡模拟程序数值模拟研究了后台阶流动中再附着过程的演变。在流动几何参数不变情况下，给出了再附长度随雷诺数的变化规律，并与实验进行了比较，二者相符得比较好。在此基础上，给出了三种典型雷诺数下，后台阶流动的回流区特征。在湍流情况下，研究了突扩比对再附长度的影响，与实验结果吻合的比较好。详细讨论了湍流情况下大涡拟序结构的瞬时再附着过程。 这些研究结果对具有再附着现象的流动结构的工程应用具有指导意义。     

基于全局动态Vreman模型的复杂非定常湍流的大涡模拟

在湍流数值模拟方法中,大涡模拟方法可以提供丰富的大涡旋信息,已逐渐成为复杂湍流问题数值研究的重要方法。而大涡模拟中,最重要的一环是尽量准确地构建能反映流场物理本质特征的亚格子应力模型。基于该思想,将一种新型的大涡模拟亚格子应力模型-Vreman亚格子应力模型用于高雷诺数三维后台阶流动的求解,计算结果与实验结果进行对比分析结果较吻合,验证了该模型的可靠性。这是对该模型用于无任何均匀流动方向的高雷诺数复杂湍流非定常流动的首次检验,计算结果优于基于传统的Smagorinsky涡粘性的动态亚格子模型。     

Buffeting in transonic flow prediction using time‐dependent turbulence model

In transonic flow conditions, the shock wave/turbulent boundary layer interaction and flow separations on wing upper surface induce flow instabilities, ‘buffet’, and then the buffeting (structure vibrations). This phenomenon can greatly influence the aerodynamic performance. These flow excitations are self‐sustained and lead to a surface effort due to pressure fluctuations. They can produce enough energy to excite the structure. The objective of the present work is to predict this unsteady phenomenon correctly by using unsteady Navier–Stokes‐averaged equations with a time‐dependent turbulence model based on the suitable (k–ε) turbulent eddy viscosity model. The model used is based on the turbulent viscosity concept where the turbulent viscosity coefficient (Cμ) is related to local deformation and rotation rates. To validate this model, flow over a flat plate at Mach number of 0.6 is first computed, then the flow around a NACA0012 airfoil. The comparison with the analytical and experimental results shows a good agreement. The ONERA OAT15A transonic airfoil was chosen to describe buffeting phenomena. Numerical simulations are done by using a Navier–Stokes SUPG (streamline upwind Petrov–Galerkin) finite‐element solver. Computational results show the ability of the present model to predict physical phenomena of the flow oscillations. The unsteady shock wave/boundary layer interaction is described. Copyright © 2005 John Wiley & Sons, Ltd.     

不可压缩粘性流动的CBS有限元解法

对于二维不可压缩粘性流动,首先通过坐标变换的方式得到了的不含对流项的NS方程,并给出了CBS有限元方法求解的一般过程。结合一类同时含有压力和速度的出口边界条件,对方腔顶盖驱动流、后向台阶绕流和圆柱绕流进行了计算。所得结果与基准解符合良好,验证了CBS算法对于定常、非定常粘性不可压缩流动问题的可行性和所用出口边界条件的无反射特性。特别的,对于圆柱绕流,Re=100时非定常升、阻力系数及漩涡脱落等非定常都得到了较好地模拟,为一进步研究自激振动等更加复杂的非定常流动问题奠定了基础。     

Particle dispersion in a single-sided backward-facing step flow

The paper describes the particle dispersion in a single-sided backward-facing step flow. Particles of well-known sizes in the diameter range from 1 to 70 μm were suspended in an air flow and the particle motion over a step was measured by mean of a laser-Doppler anemometer. Thus, the local and integral flow quantities, i.e. the mean and turbulent velocity data could be measured precisely. In the experiments, monodispersed particle size distributions were used to exclude particle size related information ambiguity, known as triggering effects or size bias. The results of this study show qualitatively and quantitatively the difference in time-averaged particle dynamics for selected particle sizes in a backward-facing step flow. The experiments show, for different sizes, the changes in the particle velocity field in comparison with the velocity field of the continuous phase deduced from the 1 μm particles, and also imply the strong influences which different particle sizes have on flow data evaluation when size effects are not taken into account with particle-related optical measuring techniques.     

Experimental study on the flow field behind a backward-facing step using a detonation-driven shock tunnel

The supersonic combustion RAM jet (SCRAM jet) engine is expected to be used in next-generation space planes and hypersonic airliners. To develop the engine, stabilized combustion in a supersonic flow field must be attained even though the residence time of flow is extremely short. A mixing process for breathed air and fuel injected into the supersonic flow field is therefore one of the most important design problems. Because the flow inside the SCRAM jet engine has high enthalpy, an experimental facility is required to produce the high-enthalpy flow field. In this study, a detonation-driven shock tunnel was built to produce a high-enthalpy flow, and a model SCRAM jet engine equipped with a backward-facing step was installed in the test section of the facility to visualize flow fields using a color schlieren technique and high-speed video camera. The fuel was injected perpendicularly to a Mach 3 flow behind the backward-facing step. The height of the step, the injection distance and injection pressure were varied to investigate the effects of the step on air/fuel mixing characteristics. The results show that the recirculation region increases as the fuel injection pressure increases. For injection behind the backward-facing step, mixing efficiency is much higher than with a flat plate. Also, the injection position has a significant influence on the size of the recirculation region generated behind the backward-facing step. The schlieren photograph and pressure histories measured on the bottom wall of the SCRAM jet engine model show that the fuel was ignited behind the step.Communicated by K. Takayama PACS 47.40.Ki     

DNS of Instantaneous Behavior in Turbulent Forced and Mixed Convection of Liquid Metal Past a Backward-Facing Step

Flow, Turbulence and Combustion - A direct numerical simulation has been performed to study instantaneous behavior in lead-bismuth eutectic flows past a vertical, backward-facing step. A turbulent...     

Numerical simulations of laminar flow over a 3D backward-facing step

A numerical investigation of laminar flow over a three-dimensional backward-facing step is presented with comparisons with detailed experimental data, available in the literature, serving to validate the numerical results. The continuity constraint method, implemented via a finite element weak statement, was employed to solve the unsteady three-dimensional Navier–Stokes equations for incompressible laminar isothermal flow. Two-dimensional numerical simulations of this step geometry underestimate the experimentally determined extent of the primary separation region for Reynolds numbers Re greater than 400. It has been postulated that this disagreement between physical and computational experiments is due to the onset of three-dimensional flow near Re ≈ 400. This paper presents a full three-dimensional simulation of the step geometry for 100⩽ Re⩽ 800 and correctly predicts the primary reattachment lengths, thus confirming the influence of three-dimensionality. Previous numerical studies have discussed possible instability modes which could induce a sudden onset of three-dimensional flow at certain critical Reynolds numbers. The current study explores the influence of the sidewall on the development of three-dimensional flow for Re greater than 400. Of particular interest is the characterization of three-dimensional vortices in the primary separation region immediately downstream of the step. The complex interaction of a wall jet, located at the step plane near the sidewall, with the mainstream flow reveals a mechanism for the increasing penetration (with increasing Reynolds number) of three-dimensional flow structures into a region of essentially two-dimensional flow near the midplane of the channel. The character and extent of the sidewall-induced flow are investigated for 100⩽Re⩽ 800. © 1997 John Wiley & Sons, Ltd.     

Finite volume computation of incompressible turbulent flows in general co-ordinates on staggered grids

A brief review of the computation of incompressible turbulent flow in complex geometries is given. A 2D finite volume method for the calculation of turbulent flow in general curvilinear co-ordinates is described. This method is based on a staggered grid arrangement and the contravariant flux componets are chosen as primitive variables. Turbulence is modelled either by the standard k–ε model or by a k–ε model based on RNG theory. Convection is approximated with central differences for the mean flow quantities and a TVD-type MUSCL scheme for the turbulence equations. The sensitivity of the method to the grid properties is investigated. An application of this method to a complex turbulent flow is presented. The results of computations are compared with experimental data and other numerical solutions and are found to be satisfactory.