四种阴离子的毛细管电泳电导检测(英文)

 采用柠檬酸 柠檬酸钠作为缓冲体系 ,使用负高压 ,对Cl-,NO3 -,HCO3 -和H2 PO4 -等 4种常见阴离子进行了分离检测 ,研究了缓冲剂的种类、浓度、pH值及操作电压对分离的影响。在选定的条件下 ,4种离子的定量线性范围 :Cl-5 0× 10 -5mol/L～ 2 5× 10 -3 mol/L ,NO3 -6 0× 10 -5mol/L～ 2 0× 10 -3 mol/L ,HCO3 -5 0× 10 -6mol/L～ 2 0× 10 -4 mol/L ,H2 PO4 -6 0× 10 -5mol/L～ 1 0× 10 -3 mol/L ;检出限 :Cl-1 5× 10 -5mol/L ,NO3 -3 0×10 -5mol/L ,HCO3 -1 0× 10 -6mol/L ,H2 PO4 -2 0× 10 -5mol/L ;峰面积的RSD (n =6 ) :Cl-3 1% ,     

化学发光法测定药物中的洛美沙星

利用洛美沙星对碱性luminol H2 O2 Cr3 + 化学发光体系有较强的抑制作用 ,建立了一种测定洛美沙星药物的新方法。线性范围为 5 .16× 10 -10 ～ 9.0 3× 10 -6mol/L ;平均回收率为 95 %～ 10 5 % ;检出限 (3δ)为 1.84× 10 -10 mol/L ;相对标准偏差为 0 .92 % (n =6 ,Cs =5 .16× 10 -10 mol/L)。用于胶囊、片剂和针剂中洛美沙星的测定 ,结果令人满意。     

锌电解液中痕量铜、镉、镍和钴的快速同时测定

研究了丁二酮肟 氨 氯化铵 柠檬酸钠 明胶 抗坏血酸体系中Cu(Ⅱ )、Cd(Ⅱ )、Ni(Ⅱ )和Co(Ⅱ )的络合物吸附波 ,建立了同时、快速测定锌电解溶液中这些痕量元素的新方法。Cu(Ⅱ )、Cd(Ⅱ )、Ni(Ⅱ )和Co(Ⅱ )分别在 - 0 44V、- 0 76V、- 1 0 7V和 - 1 2 4V左右产生灵敏的络合物吸附波。信噪比为 3时 ,其检测限分别为 1 0× 1 0 - 8mol/L、1 3× 1 0 - 8mol/L、2 9× 1 0 - 1 0 mol/L和 3 6×1 0 - 1 1 mol/L。铜、镉、镍和钴的浓度分别为 2 0× 1 0 - 8mol/L～ 2 0× 1 0 - 5 mol/L、3 0× 1 0 - 8mol/L～ 3 0× 1 0 - 5mol/L、5 4× 1 0 - 1 0 mol/L～ 5 4× 1 0 - 7mol/L和 6 8× 1 0 - 1 1 mol/L～ 6 8× 1 0 - 8mol/L时 ,与相应峰电流之间有良好的线性关系。方法已用于锌电解液中铜、镉、镍和钴的快速同时测定 ,相对标准偏差分别小于或等于 4 7%、5 1 %、4 9%和 5 3 %。     

配位吸附波同时测定PbA和InA

在 0 .0 5mol/L氯乙酸 氯乙酸钠 (pH 3.0 )介质中 ,Pb2 + 、In3 + 与二溴邻苯二胺双草酰胺酸酯 (DBAC)生成络合物 ,并吸附于电极表面 ,分别于 - 0 .5 0V、- 0 .6 3V(vs .SCE)得到络合物吸附还原波。其二阶导数峰电流与Pb2 + 、In3 + 浓度分别在 2 .5× 10 -8～ 6 .0× 10 -6mol/L、7.5× 10 -8～ 3.4× 10 -6mol/L内呈良好的线性关系 ;检出限分别为 1.5× 10 -8mol/LPb2 + 和 4 .5× 10 -8mol/LIn3 + 。应用于陶瓷颜料、矿石中微量Pb、In的测定 ,结果满意。     

ZrC-桑色素络合物在碳糊电极上的二次导数吸附伏安法测定Zr的研究

研究了Zr 桑色素络合物在碳糊电极正电位区的吸附伏安行为 ,并利用其在 0 .74V处的二次导数吸附氧化峰电流与Zr(Ⅳ )浓度为 6 .0× 10 -9～ 2 .0× 10 -6mol/L呈线性而测定Zr;检出限为 3.0× 10 -9mol/L(S/N =3)。最佳测定条件为 :2 .0mol/LHCl、1.0× 10 -5mol/L桑色素 ;富集电位为 0V(vs .SCE) ;扫描速度为2 5 0mV/s。该法不需萃取分离 ,可直接用于岩石样品中Zr的测定 ,结果满意     

电泳中介微分析法测定铁(Ⅱ)和铜(Ⅱ)

利用电泳中介微分析通过与邻菲罗啉的络合反应完成了对Fe2+与Cu2+的同时测定。在压差作用下,淌度较小的邻菲罗啉在金属离子区带之前首先进样,加高电压后,两区带电泳在磷酸缓冲液中 (pH=4. 5)混合、反应形成络合物并实现电泳分离。研究了缓冲液pH、试剂和样品区带长度对分离效果的影响。对于Fe2+与Cu2+两离子,方法的检出限(S/N=3)分别为 1. 6和 11μmol/L;线性范围分别为 5. 0×10-6 ~3. 0×10-4 mol/L(r=0. 9979)和 8. 0×10-5 ~3. 0×10-4 mol/L(r=0. 9996)。采用标准矿样验证了测定Fe2+的可行性。     

极谱催化波法测定马蔺子素

报道了在Na2 B4 O7 KH2 PO4 K2 S2 O8体系中马蔺子素的极谱催化波。拟定了测定马蔺子素的新方法。在 8.0× 10 - 3mol/LNa2 B4 O7 1.6× 10 - 2 mol/LKH2 PO4 (pH =7.7) 5 .0× 10 - 3mol/LK2 S2 O8底液中 ,极谱催化波峰电位Ep=-1.2 3V(vs .SCE) ;二阶导数峰峰电流i″p 与马蔺子素浓度在 2 .0× 10 - 9～ 2 .0× 10 - 6 mol/L范围内呈良好线性关系 ,检出限为 1.0× 10 - 9mol/L。催化波灵敏度比相应马蔺子素还原波高 75倍。采用该法测定了胶囊中马蔺子素的含量     

磷钼杂多酸光度法测定吲哚乙酸

研究了吲哚乙酸与磷钼杂多酸在浓度为 0 .0 3 mol/L的硫酸介质中发生氧化还原反应 ,形成的还原产物 (钼蓝 )在 NH3-NH4Cl缓冲溶液 (p H8.4)中最大吸收波长为 314 nm,表观摩尔吸光系数 ε值为 3.5 4× 10 4L· mol-1·cm-1 ,吲哚乙酸含量在 5 .0× 10 -7～ 5 .0× 10 -5 mol/L范围内符合比尔定律 ,检出限为 1.0× 10 -7mol/L,对 2 .0 0× 10 -5 mol/L吲哚乙酸测定 10次的相对标准偏差为 6 .42 % ,加标回收率为 94.2 %～ 10 0 .1%     

L-半胱氨酸自组装膜电极对米吐尔的电催化及其分析应用

研究了米吐尔在L 半胱氨酸自组装膜修饰金电极上的电化学行为。米吐尔在该修饰电极上的CV曲线仅出现一对峰 ,其峰形对称 ,ΔEp =42mV ,氧化还原峰电流之比约等于 1,为可逆反应 ;扩散系数D =2 .2 4× 10 - 6 cm2 ·s- 1 。初步探讨了电催化机理。差分脉冲伏安法测定其氧化峰电流与米吐尔浓度在 5 .0× 10 - 7～ 2 .0× 10 - 5mol/L和 5 .0× 10 - 5～ 1.0× 10 - 3 mol/L范围内分段呈线性关系 ;相关系数分别为 0 .9987和 0 .9972 ;检测限 1.0× 10 - 8mol/L     

氟苯尼考的极谱法研究

应用循环伏安法、线性扫描伏安法和控制电位电解库仑法对氟苯尼考的电化学行为进行了研究。在0 .2mol/LNaOH NaH2 PO4(pH =7.6 )缓冲液中 ,对其进行扫描 ,发现于 - 0 .886V (vs.SCE)处产生一灵敏的还原峰 ,其峰电流与氟苯尼考的浓度在 1.0× 10 -5～ 7.0× 10 -4mol/L范围内呈良好的线性关系 (r =0 .9994 ) ;检出限为 1.0× 10 -6mol/L。对 1.0× 10 -4mol/L氟苯尼考溶液进行 10次平行实验 ,RSD为 0 .3%。实验结果表明 :氟苯尼考在极谱电极上有吸附性质 ;求得了电极反应的电子转移数为 2 ;研究了电极反应机理     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.