四苯基卟啉锌/TiO2纳米复合材料的原位合成及可见光光催化

利用溶胶-凝胶法,经400℃(4 h)烧结后,原位合成不同摩尔比的5,10,15,20-四苯基卟啉锌(ZnTPP)/TiO2纳米复合材料,通过XRD,FTIR,UV-Vis,荧光光谱等表征分析,确认复合材料中TiO2为锐钛矿相,且ZnTPP在该过程中原位生成.经150 min可见光辐照,摩尔比为1:100的ZnTPP/TiO2复合材料能使罗丹明B溶液降解率达到92%.其光催化敏化的机理为,通过ZnTPP与TiO2之间的Zn-O键,使光生载流子形成有效的分离,提高了光催化性能.     

镍锰共掺杂TiO2的制备及其光催化性能研究

采用溶胶-凝胶的方法,镍、锰离子在钛酸丁酯[Ti(OBu)4]水解的条件下掺杂到TiO2中,合成了不同摩尔比的镍、锰离子共掺杂的TiO2光催化剂.通过光催化降解甲基橙实验,对所制备光催化剂的光催化活性进行了考察.结果表明掺杂后的TiO2光催化剂在可见光下对甲基橙能有效地降解,表现出了较好的光催化活性,当镍、锰离子掺杂量...     

Meso-四(对磺酸基苯基)卟啉锌在二维ZnO表面原位中心取代合成及可见光选择性光催化

提高光催化剂降解污染物的效率和选择性,近年来引起了诸多研究者的关注。通过原位中心取代合成方法,合成了Meso-四(对磺酸基苯基)卟啉锌/氧化锌(ZnTPPS_4/ZnO NAs)复合材料。通过X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见吸收光谱(UV-Vis)和红外光谱(FTIR)等方法,对其晶体结构、形貌、组成和官能团进行表征,证明了在二维ZnO表面上的Zn原子,原位取代Meso-四(对磺酸基苯基)卟啉(TPPS_4)中心的氢原子,并与之形成中心配位。同时,对二维ZnO进行表面改性,增强其亲水性。分别将ZnTPPS_4/ZnO NAs和ZnO,对亲水性染料罗丹明B(RhB)和疏水性的苯酚(PL),进行可见光光催化实验,结果表明,亲水性ZnTPPS_4/ZnONAs对罗丹明B降解效率高,呈现出显著的光催化选择性。     

纳米TiO2薄膜的结构及光催化特性

利用磁控溅射方法在单晶硅和石英衬底表面沉积TiO2薄膜. 通过调节实验参量,制备出不同结构的TiO2薄膜. 通过X射线衍射、扫描电镜、拉曼光谱、吸收光谱等对样品进行表征,同时对不同结构的TiO2薄膜的光催化特性进行分析,发现具有网络状结构锐钛矿相的TiO2薄膜具有更高的光催化能力. 本文对不同薄膜的表面形貌和生长机理进行分析,并讨论TiO2结构和表面形貌对其光催化特性的影响.     

纳米复合材料TiO2-ZrO2光催化降解可溶性染料的研究

采用溶胶-凝胶方法将光催化剂TiO2和ZrO2复合,再经700℃灼烧5h后获得了纳米复合光催化材料TiO2-ZrO2.该材料经XRD检测具有光催化活性良好的晶型结构.TEM测定结果显示产物的平均粒径约为20nm.通过对可溶性染料刚果红等的光催化降解实验证明,该复合材料具有较高的光催化活性.     

PbSe/TiO2同轴异质结纳米管的制备及光催化性能

通过溶液法合成了PbSe/TiO2复合纳米管,并对其进行了微观形貌、晶体结构等的表征。结果表明,制得的样品是由PbSe和TiO2两种材料构成的复合材料,致密、均匀的TiO2薄膜包覆在PbSe纳米管表面。以氙灯为模拟光源,通过对甲基橙的降解研究了PbSe/TiO2复合纳米管的光催化性能。结果显示,PbSe与TiO2之间形成的异质结使PbSe/TiO2复合纳米管具有较高的光催化性能,比纯PbSe纳米管的催化降解率提高了约4.5倍。另外,对PbSe/TiO2复合纳米管光催化稳定性也进行了研究。     

DBU液相催化法原位合成四苯氧基酞菁锌/ZnO复合材料的制备及光催化选择性研究

在负载于氧化铟锡(ITO)导电玻璃上、哑铃状纳米ZnO表面配位未饱和锌离子作为“模板”,以苯氧基邻苯二腈作为“分子碎片”,利用DBU液相催化法,在亲水性纳米ZnO表面,原位合成疏水性四苯氧基酞菁锌(ZnTPPc)。通过多种表征手段,分析证实了所合成的ZnTPPc分子结构、ZnTPPc/ZnO界面及光生电荷转移特性。在可见光下,分别以亲水性亚甲基蓝(MB)、疏水性苯酚(PL)及其混合液为待降解反应物,定量分析疏水性ZnTPPc/ZnO复合材料对降解疏水性PL的光催化选择性。结果表明： 原位合成ZnTPPc在ZnO表面呈现单分子层,具有较好的疏水性能,ZnTPPc可优先选择性降解疏水性PL,且在可见光光催化中对PL的相对降解效率是对MB分子的1.21倍。     

TiO_2/白云母纳米复合材料的色度学研究

利用化学液相沉积法制备了系列TiO2白云母纳米复合材料.在利用扫描电子显微镜、X射线衍射对其进行表面形貌、TiO2纳米镀层物相组成研究的基础上,仔细研究了TiO2白云母纳米复合材料在可见光下的反射光谱特征,并利用Munsell新坐标(HVC)色度学系统对其可见光下的干涉色颜色进行了定量表征. 关键词： TiO_2/白云母纳米复合材料 反射光谱 色度学 Munsell新坐标     

铁氮共掺杂纳米TiO_2复合膜的制备、光谱分析及光催化活性研究

用溶胶-凝胶法制备铁、氮共掺杂纳米TiO2凝胶,浸渍-提拉法将其镀膜于载玻片表面,经干燥、煅烧,制得Fe-TiO2-xNr复合膜;用XRD,SEM,XPS及UV-Vis对镀膜样品进行了表征.XRD分析表明,Fe-TiO2-xNr膜为锐钛矿结构,少数氮原子替代了TiO2晶格中的氧;SEM照片说明,构成膜的粒子分散均匀,形貌一致,粒径约19 nm:UV-Vis漫反射光谱显示,Fe3+掺杂可使复合膜对可见光的响应红移至740nm处;XPS图谱证明,铁、氮的掺入降低了Ti(2p3/2)电子结合能,从而拓宽了TiO2在可见光区的吸收范围.以光催化降解苏丹红I为模型反应,比较了不同掺杂样品的光催化活性,结果表明,当掺杂的Fe3+相对于Ti4-1的原子比达到0.4%时,复合膜表现出最佳催化性能,4 h后对苏丹红I的降解率达到97%.方法制备的氮和适量铁共掺杂Fe-TiO2-xNr复合膜能协同提高TiO2对可见光的响应能力及光催化活性,在污水处理领域具有潜在的应用价值.     

SO2-4/CeO2-TiO2光催化材料的制备与光谱表征

采用溶胶-凝胶法结合硫酸浸渍法制备了SO2-4/CeO2-TiO2复合氧化物.利用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、吡啶吸附红外光谱(Py-FTIR)、紫外-可见光漫反射光谱(UV-Vis)、X射线光电子能谱价带谱(VB-XPS)及荧光光谱(PL)技术对样品的结构、性质进行了表征,以光催化分解水制氢为模型反应,评价了样品的光催化性能.XRD,FTIR结合PL结果表明CeO2与TiO2的复合形成了异质结构,有利于提高光生电子与光生空穴的分离效率,对催化剂活性的提高有促进作用;Py-FTIR谱图证明SO2-4/CeO2-TiO2复合氧化物在表面具有Lewis酸性,Lewis酸性位的产生是由于SO2-4在样品表面的配位吸附所致,S O— 的诱导效应增强了表面金属得电子能力,从而进一步提升光生载流子的分离效率;UV-Vis及XPS价带谱分析说明,半导体氧化物复合能够缩减带隙,拓宽光响应范围,Lewis酸性影响复合氧化物的能带结构,使其导带底位置向负向移动,利于光催化还原能力的提高,进而促进其光催化制氢活性.光催化分解水制氢实验结果表明,SO2-4/CeO2-TiO2复合氧化物具有优于纯氧化物CeO2,TiO2及未经硫酸浸渍的CeO2-TiO2复合氧化物的催化活性,5 h的产氢速率为1934.1μmol·g-1·h-1.光谱分析结果结合光催化制氢活性评价结果表明,SO2-4/CeO2-TiO2复合氧化物的异质结构与酸浸渍是影响样品光催化性能的主要因素.     

Unprecedented coloration of rutile titanium dioxide nanocrystalline thin films

In this communication, TiO2 nanocrystalline thin films synthesized by a room temperature (27 degrees C) chemical dip process. To our knowledge, this is first report of the preparation of nanoscale rutile TiO2 particles from common inorganic salt at such low temperature. Interestingly, unprecedented dynamic color change accompanies with titanium dioxide grain size, which can be seen with the naked eye that generated curiosity in our mind to check UV-vis absorption, where significant changes were observed. The room temperature synthesized thin films of rutile titanium dioxide make it a potential candidate for high-compatibility material, which can be used in artificial heart valves.     

Sonophotocatalytic degradation of congo red and methyl orange in the presence of TiO2 as a catalyst

A comparative study between the photocatalytic and sonophotocatalytic oxidation process of congo red was carried out using titanium dioxide as a catalyst. The effect of a number of parameters, such as the initial concentration of dye, the presence of oxygen and ultrasound, the TiO(2) crystalline structure and the amount of TiO(2), was studied using an inexpensive reactor. In the second part of this document, the oxidation and reduction processes of methyl orange was studied using the same reactor, but by changing the chemical environment in order to drive either the oxidation or the reduction reaction. The results showed, for all the cases studied, a sinergistic effect between sonolysis and photocatalysis when an ultrasonic bath of 80W was used as a source of ultrasound. On the other hand, the electrochemical experiments showed that the current densities for the oxidation process of the azodyes were higher when a conducting glass electrode covered with a thin film of TiO(2) was used as a working electrode instead of a platinum electrode, showing that the TiO(2) electrode is not passivated by the oxidation reaction.     

Sono-synthesis of core-shell nanocrystal (CdS/TiO2) without surfactant

A core-shell nanocomposite (CdS/TiO(2)) was synthesized at relatively low temperature (70°C) with small particle sizes (~11 nm). First, CdS nanoparticles were prepared by a combination of ultrasound and new micro-emulsion (O/W) without surfactant. Then the synthesized CdS was easily combined with TiO(2) under sonication. The formation of uniform surface layer of TiO(2) with depths of 0.75-1.1 nm on the CdS led to an increase of particle size. Ultrasonic irradiation can control the hydrolysis and condensation of titanium tetra-isopropoxide (TTIP) and the formation of TiO(2) shell around the CdS core. This technique avoids some of the problems that exist in conventional microemulsion synthesis such as the presence of different additives and calcinations. It was found that nanocomposite particles extend the optical absorption spectrum into the visible region in comparison with pure TiO(2) and pure CdS. In addition, a larger depth of TiO(2) led to a red-shift of the absorption band in nanocomposite. The characterization of nanocomposites has been studied by HRTEM, TEM, XRD, EDAX, BET and, UV-vis.     

Effects of Gold and Silver Nanoparticles on Optical Bistability of Titanium Dioxide Nanocolloid

Physics of the Solid State - In this study, titanium dioxide (TiO2) nanocolloid was synthesized through sol–gel method, and nonlinear optical properties were studied using z-scan method. The...     

SnO2-TiO2复合颗粒的形态结构及其光催化活性

在气溶胶反应器中，利用ＴｉＣｌ４高温氧化反应制备超细ＴｉＯ２，采用均匀沉淀法在ＴｉＯ２表面沉积ＳｎＯ２制备ＳｎＯ２－ＴｉＯ２复合颗粒，应用ＴＥＭ、ＥＥＤＳ、ＳＲＤ、ＢＥＴ比表面积测试等手段对粒子进行表征。以活性艳红Ｘ－３Ｂ复合颗粒，应用ＴＥＭ、ＥＤＳ、ＸＲＤ、ＢＥＴ比表面积测试等手段对粒子进行表征。以活性艳红Ｘ－３Ｂ溶液为处理对象考察复合颗粒的光催化活性。结果表明ＳｎＯ２－ＴｉＯ２复合颗粒的光催化     

掺磷TiO_2优化TiO_2/MBA/Ag三明治结构的SERS性能

本文以磷酸为磷源,通过溶胶水热法制备磷掺杂TiO_2,利用Lee和Meisel的方法制备银溶胶,以4-巯基苯甲酸(MBA)为探针分子,通过构建TiO_2/MBA/Ag三明治结构,研究磷掺杂二氧化钛对该基底表面增强拉曼(SERS)性能的提升。通过TEM、XRD、XPS、DRS和拉曼光谱图表征二氧化钛的形貌结构、化学组成、光学和拉曼性能,结果表明,制备出的磷掺杂二氧化钛为锐钛矿型纳米颗粒,粒径范围6~12nm,XPS显示磷以P~(5+)替代了Ti~(4+),形成O-P-O键掺入TiO_2的晶格中,当磷的掺杂量在1.77%时,TiO_2/MBA/Ag三明治体系具有最佳的SERS信号,这是因为适量的磷掺杂降低了TiO_2的能带间隙,丰富TiO_2的表面态,这能促进TiO_2向MBA分子的电荷转移。     

Investigation on the sonocatalytic degradation of acid red B in the presence of nanometer TiO2 catalysts and comparison of catalytic activities of anatase and rutile TiO2 powders

Here, the nanometer anatase and rutile titanium dioxide (TiO(2)) powders were introduced to act as the sonocatalysts during the ultrasonic degradation of azo dye-acid red B which was chosen as model compound. The ultrasound of low power was used as an irradiation source to induce TiO(2) particles performing catalytic activity. It was found that the processes of sonocatalytic degradation were different between nanometer anatase TiO(2) and nanometer rutile TiO(2). For nanometer anatase TiO(2) catalyst, the acid red B was mainly oxidated by the holes on the surface of nanometer anatase TiO(2) particles, so that the decolorization and degradation happened at the same time. For the nanometer rutile TiO(2) catalyst, the acid red B was mainly oxidated by the *OH radicals from the ultrasonic cavitation, so that the decolorization of azo bond takes place primarily, and then the degradation of naphthyl ring does. The intermediates of acid red B in the presence of nanometer anatase and rutile TiO(2) powders have been monitored by UV-vis spectra and high performance liquid chromatography (HPLC), respectively. All experiments indicated that the degradation effect of acid red B in the presence of nanometer anatase TiO(2) powder was obviously better than that in the presence of nanometer rutile TiO(2) powder. Hence, the method of sonocatalytic degradation for organic pollutants in the presence of nanometer anatase TiO(2) powder is expected to be promising as an advisable choice for the treatment of organic wastewaters in future.     

La-Ce-TiO_2纳米光催化剂的溶胶-微波法合成、谱学表征及其活性研究

以钛酸四丁酯为原料,采用溶胶-微波法(Sol-Microwave Method)合成了镧和铈共掺型纳米TiO2粉体(La-Ce-TiO2),借助XRD、XPS和UV-Vis等测试手段对其进行了表征,并以甲基橙为模型污染物考察了掺杂量对样品光催化活性的影响规律.XRD分析表明,所得粉体均为锐钛矿相纳米TiO2,且稀土元素镧和铈掺杂后纳米TiO2特征衍射峰宽化,强度降低;XPS分析表明,镧和铈掺杂后样品表面存在大量的氧缺位;UV-Vis吸收光谱表明,所得粉体在400 nm以下均有连续宽化的吸收带,且La和Ce掺杂后样品对光的吸收显著增强,这足由于La(Ⅲ)-O荷移跃迁以及Ce(Ⅳ)f→d跃迁和Ce(Ⅳ)-O荷移跃迁所致;光催化实验表明,La和Ce共掺杂能显著提高纳米TiO2的光催化活性,其中当La(Ⅲ)和Ce(Ⅳ)掺杂量分别为2%和0.04%时,纳米TiO2光催化剂具有较高的催化活性,自然光照射下光催化氧化处理卷烟厂蒸叶车间废水,效果较好,废水COD去除率达到86.11%.     

Effect of particle addition on sonochemical reaction

Enhancement of chemical reaction with a photocatalyst of titanium dioxide (TiO(2)) by ultrasonic irradiation is studied through the absorbance measurements for liberation of iodine from a KI aqueous solution as an index of oxidation reaction. It is well known as a synergetic effect that the addition of TiO(2) fine particles under UV has an ability to enhance the yield in chemical reaction with OH-radical from hot spot at violent collapse of cavitation bubbles with intense ultrasound. In this study, the absorbance is measured after simultaneous irradiation of ultrasound and UV with the addition of TiO(2) much less than the usual concentration by two orders of content. It is shown that, even in case of quite a little TiO(2) addition where the photocatalytic effect is less, the yield is enhanced obviously in comparison with the summation in yield of independent procedure of ultrasound without TiO(2) and UV with TiO(2). The absorbance-peak deviation to the shorter wavelength implies the generation of titanium peroxide (TiO(3)). The effect of particle addition is due to the chemically activated particle surface on the TiO(2) and probably to the increase in the cavitation bubbles that results in promoting a transfer of OH-radical and other oxidants to bulk liquid region at the collapse.