带有可更换半自准工作电极的集成化毛细管电泳安培检测芯片

自Woolley等首次报道集成于玻璃芯片上的微型毛细管电泳-安培检测(Chip-based capillary electrophoresis with amperometric detection,CE-AD)系统以来,CE-AD以其高效、高速、高灵敏度以及易微型化集成化等特点引起研究者的关注．在芯片上实现柱端安培检测可用直接制作在芯片上的喷(镀)膜工作电极,或采用外置的壁喷式电极。前者集成化程度高,后者的工作电极可以更换,大大提高了芯片的重复利用率。     

塑料芯片毛细管电泳电化学检测系统及其性能评价

近年来,高分子芯片毛细管电泳技术发展迅速,以聚甲基丙烯酸甲酯(PMMA)为代表的塑料电泳芯片由于其低廉的制作成本与良好的电渗性能,已经成为芯片电泳技术发展的一个重要方向,电化学检测具有灵敏度高、选择性好和易于微型化等优点,因此在塑料芯片电泳领域中具有较好的应用前景。     

In-channel modification of electrochemical detector for the detection of bio-targets on microchip

The coulometric efficiency (C_eff) of an amperometric detector integrated on PDMS/glass capillary electrophoresis microfluidic device (microchip) has been enhanced by in-channel electrochemical modification. In-channel electrochemical deposition of gold particles was performed in order to vertically increase the surface area of the Au sensing microelectrode. The roughness of the electrodes was characterized using scanning electron microscopy and profilometric analysis. The degree of electrode modification was also characterized by roughness factor determination. Separation processes including detection potential was optimized and the analytical performance of the microchip was tested using a mixture of dopamine (DA) and catechol (CA). The modified electrochemical detector provided well-resolved separation of DA and CA in less than 60 s with enhanced sensitivity; no peak broadening was observed. The limit of detection using in-channel modification of working electrode for DA and CA are 60 and 110 nM, respectively. Thus, in-channel electrochemical deposition of metallic particles should be used to enhance the C_eff of integrated amperometric detection of analytes with good redox properties in order to obtain lower LODs.     

Fabrication of a gold microelectrode for amperometric detection on a polycarbonate electrophoresis chip by photodirected electroless plating

A novel method of photoresist-free micropatterning coupled with electroless gold plating is described for the fabrication of an integrated gold electrode for electrochemical detection (ED) on a polycarbonate (PC) electrophoresis microchip. The microelectrode layout was photochemically patterned onto the surface of a PC plate by selective exposure of the surface coated without photoresist to 254 nm UV light through a chromium/quartz photomask. Thus, the PC plate was selectively sensitized by formation of reactive chemical moieties in the exposed areas. After a series of wet chemistry reactions, the UV-exposed area was activated with a layer of gold nanoparticles that served as a seed to catalyze the electroless plating. The gold microelectrode was then selectively plated onto the activated area by using an electroless gold plating bath. Nonselective gold deposition on the unwanted areas was eliminated by sonication of the activated PC plate in a KSCN solution before electroless plating, and the adhesion of the plated electrodes to the PC surface was strengthened with thermal annealing. Compared with the previously reported electroless plating technique for fabrication of microelectrodes on a microchip, the present method avoided the use of a membrane stencil with an electrode pattern to restrict the area to be wet-chemically sensitized. The CE with integrated ED (CE-ED) microchip was assembled by thermal bonding an electrode-plated PC cover plate to a microchannel-embossed PC substrate. The novel method allows one to fabricate low-cost, electrode-integrated, complete PC CE-ED chips with no need of a clean room. The fabricated CE-ED microchip was demonstrated for separation and detection of model analytes, including dopamine (DA) and catechol (CA). Detection limits of 0.65 and 1.03 microM were achieved for DA and CA, respectively, and theoretical plate number of 1.4 x 10(4) was obtained for DA. The plated gold electrode can be used for about 4 h, bearing usually more than 100 runs before complete failure.     

An end-channel amperometric detector for microchip capillary electrophoresis

An end-channel amperometric detector with a guide tube for working electrode was designed and integrated on a home-made glass microchip. The guide tube was directly patterned and fabricated at the end of the detection reservoir, which made the fixation and alignment of working electrode relatively easy. The fabrication was carried out in a two-step etching process. A 30 μm carbon fiber microdisk electrode and Pt cathode were also integrated onto the amperometric detector. The characteristics and primary performance of the home-made microchip capillary electrophoresis (MCCE) were investigated with neurotransmitters. The baseline separation of dopamine (DA), catechol (CA) and epinephrine (EP) was achieved within 80 s. Separation parameters such as injection time, buffer components, pH of the buffer were studied. Relative standard deviations of not more than 6.0% were obtained for both peak currents and migration times. Under the selected separation conditions, the response for DA was linear from 5 to 200 μM and from 20 to 800 μM for CA. The limits of detection of DA and CA were 0.51 and 2.9 μM, respectively (S/N=3).     

安培检测芯片毛细管电泳及其初步应用

An end-channel amperometric detector with a guide tube for working electrode was designed and integrated on a home-made glass microchip. The guide tube was directly patterned and fabricated at the end of the detection reservoir, which made the fixation and alignment of working electrode relatively easy. The fabrication was carried out in a two-step etching process. A 30 μm carbon fiber microdisk electrode and Pt cathode were also integrated onto the amperometric detector. The baseline separation of dopamine (DA), catechol (CA) and epinephrine (EP) was achieved within 80 s. Relative standard deviations of not more than 5.2% were obtained for both peak currents and migration times of DA and CA (n=5). Using standard adding method, DA in tLrine and plasma samples was detected. The recoveries were in the range of 83%—103%.     

Simple amperometric detector for microchip capillary electrophoresis, and its application to the analysis of dopamine and catechol

We report on a simple amperometric detector for use in microchip capillary electrophoresis. A disposable syringe serves as the electrode holder that is fixed at the outlet of the separation channel. A carbon paste electrode is used to detect dopamine (DA) and catechol (CA) after electrophoretic separation. The two model analytes were well separated within 60 s. The response is linear in the concentration range from 4 to 500???M, and the detection limit is 1.2???M for DA (S/N = 3:1). The relative standard deviations of the inter-run and inter-electrode peak currents, respectively, are 2.8% and 5.7% for DA, and 3.9% and 6.5% for CA. Favorable column efficiency (expressed by the theoretical plate number which is 5.3 × 104 m^-1 for DA) is achieved. The method was successfully applied to the separation and detection of 3-aminophenol (3-AP) in an injection powder containing sodium 4-aminosalicylate. The detection limit of 3-AP is as low as 1.7???M, which meets the demand of the impurity test. The facile assembly allows convenient replacement of working electrodes and improves the longevity of the microanalytical system.

Microchannel-electrode alignment and separation parameters comparison in microchip capillary electrophoresis by scanning electrochemical microscopy

The end of separation channel in a microchip was electrochemically mapped using the feedback imaging mode of scanning electrochemical microscopy (SECM). This method provides a convenient way for microchannel-electrode alignment in microchip capillary electrophoresis. Influence of electrode-to-channel positions on separation parameters in this capillary electrophoresis-electrochemical detection (CE-ED) was then investigated. For the trapezoid shaped microchannel, detection in the central area resulted in the best apparent separation efficiency and peak shape. In the electrode-to-channel distance ranging from 65 to 15mum, the limiting peak currents of dopamine increased with the decrease of the detection distance due to the limited diffusion and convection of the sample band. Results showed that radial position and axial distance of the detection electrode to microchannel was important for the improvement of separation parameters in CE amperometric detection.     

Amperometric detector designs for capillary electrophoresis microchips

Electrochemical (EC) detection is a sensitive and miniaturisable detection mode for capillary electrophoresis (CE) microchips. Detection cell design is very important in order to ensure electrical isolation from the high separation voltage. Amperometric detectors with different designs have been developed for coupling EC detection to CE-microchips. Different working electrode alignment: in-channel or end-channel has been tested in conjunction with several materials: gold, platinum or carbon. The end-channel detector was based on a platinum or gold wire manually aligned at the exit of the separation channel. Thick- (screen-printed carbon electrode) and thin-film (sputtered gold film) electrodes have also been employed with this configuration, but with a different design that allowed the rapid replacement of the electrode. The in-channel detector was based on a gold film within the separation channel. A gold-based dual electrode detector, which combined for the first time in- and end-channel detection, has been also tested. These amperometric detectors have been evaluated in combination to poly(methylmethacrylate) (PMMA) and Topas (thermoplastic olefin polymer of amorphous structure) CE-microchips. Topas is a new and promising cyclic olefin copolymer with high chemical resistance. Relevant parameters of the polymer microchip separation such as precision, efficiency or resolution and amperometric detection were studied with the different detector designs using p-aminophenol and L-ascorbic acid as model analytes in Tris-based buffer pH 9.0.     

Performance evaluation of a capillary electrophoresis electrochemical chip integrated with gold nanoelectrode ensemble working and decoupler electrodes

This paper presents a capillary electrophoresis poly(methyl methacrylate) (PMMA) based microchip for electrochemical detection applications featuring embedded gold nanoelectrode ensemble (GNEE) working and decoupler electrodes. In fabricating the microchip, the GNEE films are pressed directly onto the metallic electrode structures using a hot embossing technique, and the microfluidic channels are then sealed using a low-temperature azeotropic solvent bonding method. The detection performance of the microchip is evaluated using dopamine and catechol analytes for illustration purposes. The experimental results show that the GNEE working electrode provides a significantly higher signal response than that obtained from a bulk gold electrode when applied to the detection of dopamine analyte. Compared to a conventional bulk palladium decoupler electrode, the GNEE decoupler electrode reduces both the amplitude of the charge current (3.5 nA vs. 18.7 nA) and the baseline drift at higher separation voltages. The measured baseline current drift for the microchip equipped the proposed GNEE decoupler electrode is around three times smaller than the microchip with the palladium decoupler electrode under the applied separation electric field from 40 V/cm to 240 V/cm. Finally, when detecting a mixture of 1mM dopamine and 1mM catechol, the calculated signal response of the microchip with a GNEE decoupler electrode is approximately five times higher than that obtained from a microchip with a bulk Pd decoupler electrode, resulting in the detection limit of 1 microM for the proposed GNEE-based microchip device. Overall, the results indicate that the proposed capillary electrophoresis-electrochemical detection (CE-ED) microchip with embedded GNEE working and decoupler electrodes provides an ideal solution for sample detection in lab-on-a-chip and micro total analysis applications.     

新型安培检测毛细管电泳微系统

将电极、６ｃｍ分离毛细管、缓冲池、检测池集成于８．４×５．０ｃｍ有机玻璃片上,制作了一个毛细管电泳微系统。以碳纤维微盘电极作为工作电极,采用三电极体系柱端检测了１×１０－４ｍｏｌ／Ｌ多巴胺（ＤＡ）,具有良好的重现性,检测限３．６×１０－８ ｍｏｌ／Ｌ,线性范围５×１０－７～１×１０－４ｍｏｌ／Ｌ,并在该系统上分离了邻苯二酚（ＣＡ）和多巴胺的混合物。     

新型芯片电泳柱端安培检测系统的构建与评价

自行设计开发了一套便于与电泳芯片集成的一体式柱端安培检测池系统．该系统由整块透明有机玻璃精密加工而成,包括电泳芯片支架和安培检测池两部分,芯片可通过芯片插槽和不锈钢夹具固定在芯片支架上,各种检测用电极可直接通过螺母固定在安培检测池中．以100μmol／L的DA为模式分析物,分别采用直径为100、300和500μm的铂金圆盘电极与表观直径为240μm的碳纤维电极作为工作电极均在该装置上实现了良好组装和高灵敏检测．采用碳纤维工作电极对该系统的检测参数进行了优化．测试结果表明该系统在电化学清洗程序下连续六次测定100μmol／L多巴胺的峰电流相对标准偏差为3．2％,保留时间相对标准偏差为0．5％,DA的检测限为0．4μmol／L（按照S／N=3计）．该系统体积小巧,测试稳定,检测灵敏度较高,工作电极更换方便,适合作为芯片电泳柱端安培检测通用平台．     

A three-dimensionally adjustable amperometric detector for microchip electrophoretic measurement of nitroaromatic pollutants

A microchip capillary electrophoresis (CE)–amperometric detection (AD) system has been fabricated by integrating a two-dimensionally adjustable CE microchip and an amperometric detection cell containing a one-dimensionally adjustable disc detection electrode in a Plexiglas holder. It facilitates the precise three-dimensional alignment between the channel outlet and the detection electrode without a complicated three-dimensional manipulator. The performance of this unique system was demonstrated by separating four nitroaromatic pollutants (nitrobenzene, 2,4-dinitrotoluene, 2,4,6-trinitrotoluene, and p-nitrobenzene). Factors influencing their separation and detection processes were examined and optimised. The four analytes have been well-separated within 120 s in a 75 cm long separation channel at a separation voltage of +2000 V using an electrophoretic separation medium containing 15 mM borax and 15 mM sodium dodecyl sulfate (pH 9.2). Highly linear response is obtained for the four analytes over the range of 0–5 ppm with the detection limits ranging from 12 to 52 ppb. The present system demonstrated long-term stability and reproducibility with relative standard deviations of less than 5% for the peak current (n = 9). The new approach for the microchannel–electrode alignment should find a wide range of applications in other microfluidic analysis systems.     

Nanoband electrode for high-performance in-channel amperometric detection in dual-channel microchip capillary electrophoresis

A nanoband electrode detector integrated with a dual-channel polydimethylsiloxane microchip is proposed for in-channel amperometric detection in microchip capillary electrophoresis. Gold nanoband electrodes, which were fabricated on SU-8 substrates with a 100-nm-width gold layer, were introduced into the dual-channel microchip to be an electrochemical detector. Due to the nano-sized width of the detector, the noise of the amperometric detection was significantly reduced, and a high separation resolution was achieved for monitoring the analytes. The detection sensitivity of the system was improved by high signal-to-noise ratio, and a low detection limit on microchip was obtained for p-aminophenol (2.09 nM). Because of the high resolution in measuring half-peak width, the plate number that is used to evaluate the separation efficiency was 1.5-fold higher than that using 50-μm-width electrochemical detector. The effect of sample injection time and data acquisition time on separation efficiency was investigated, and an attractive separation efficiency was achieved with a plate number up to 17,500.     

Microchip capillary electrophoresis with electrochemical detector for fast measurements of aromatic amino acids

A method based on microchip capillary electrophoresis with amperometric detection was developed for the rapid separation and direct detection of oxidizable aromatic amino acids (without prior derivatization). The working electrode was a thick-film carbon strip electrode positioned opposite the outlet of the separation channel. Factors influencing the separation and detection processes were examined and optimized. The five aromatic amino acids, tyrosine, 5-hydroxytryptophan, tryptophan, p-aminobenzoic acid, and m-aminobenzoic acid, can be well separated within 5 min using a separation voltage of 2000 V and a 25 mM phosphate buffer (pH 7.0) run buffer containing 50 mM sodium dodecylsulfate. Most favorable amperometric detection was obtained at +0.95 V. Linear calibration plots are observed for micromolar concentrations of the oxidizable amino acids. The new protocol offers good stability and for reproducibility, with relative S.D. of less than 5% for both migration times and peak currents (n=8). It should be useful for the analysis of aromatic amino acids, as desired for life sciences.     

Poly(dimethylsiloxane) microchip capillary electrophoresis with electrochemical detection for rapid measurement of acetaminophen and its hydrolysate

Poly(dimethylsiloxane) microchip capillary electrophoresis with amperometric detection has been used for rapid separation and determination of acetaminophen and its hydrolysate, i.e. p-aminophenol. A Pt ultramicroelectrode with a diameter of 10 m positioned at the outlet of the separation channel was used as a working electrode for amperometric detection. Factors influencing separation and detection were investigated and optimized. Results show that acetaminophen and p-aminophenol can be well separated within 35 s with RSD<1% for migration time and <7% for detection current for both analytes. Detection limits for both analytes are estimated to be 5.0 mol L^–1 (approximately 0.1 fmol) at S/N=3. This method has been successfully applied to the detection of traces of p-aminophenol in paracetamol tablets.     

芯片毛细管电泳-安培检测系统

由于安培检测具有的高灵敏度、低成本、低能耗、易集成化便携化、与微加工技术匹配等特点,芯片毛细管电泳-安培检测系统（μCE-AD）的研究近年来得到人们广泛的关注。本文结合本课题组的研究工作,对近年来μCE-AD的研究进展进行评述;重点讨论了近年来在芯片的设计、集成化电极的制备、消除分离电压的干扰等方面的进展;同时介绍了利用分离电场拓展检测范围、阵列电极和阵列通道、化学修饰电极的应用、新型进样技术和试样预处理等方面的新成就;最后展望了未来μCE-AD的发展趋势。     

In-channel dual-electrode amperometric detection in electrophoretic chips with a palladium film decoupler

An electrophoretic microchip integrated with a Pd-film decoupler and a series-dual electrode was proven practical (200-800 V/cm) for routine amperometric detection. In fluidic systems, amperometric enhancement of parallel-opposed dual-electrode detection is due to redox cycling of analytes between the electrodes. We, however, found that the oxidation current of catecholamines was enhanced significantly (1.9-3.8 folds) by switching from the single electrode mode to dual-series mode. This novel finding was unexpected because the unidirectional flow characteristic of the microfluidic system should eliminate the possibility for analytes physically migrating back and forth between the upstream and downstream electrodes. We attribute the enhancement to turbulence generated by impinging of the flow onto the edge of the downstream electrode. The linear range, sensitivity, limit of detection (S/N = 3) and number of theoretical plates for DA and CA are, respectively, 0.5-50 microM, 47 pA/microM, 0.25 microM, 7000 m(-1) and 1.0-100 microM, 28 pA/microM, 0.49 microM, 15,000 m(-1).     

Poly(methylmethacrylate) and Topas capillary electrophoresis microchip performance with electrochemical detection

A capillary electrophoresis (CE) microchip made of a new and promising polymeric material: Topas (thermoplastic olefin polymer of amorphous structure), a cyclic olefin copolymer with high chemical resistance, has been tested for the first time with analytical purposes, employing an electrochemical detection. A simple end-channel platinum amperometric detector has been designed, checked, and optimized in a poly-(methylmethacrylate) (PMMA) CE microchip. The end-channel design is based on a platinum wire manually aligned at the exit of the separation channel. This is a simple and durable detection in which the working electrode is not pretreated. H(2)O(2) was employed as model analyte to study the performance of the PMMA microchip and the detector. Factors influencing migration and detection processes were examined and optimized. Separation of H(2)O(2) and L-ascorbic acid (AsA) was developed in order to evaluate the efficiency of microchips using different buffer systems. This detection has been checked for the first time with a microchip made of Topas, obtaining a good linear relationship for mixtures of H(2)O(2) and AsA in different buffers.     

芯片毛细管电泳电化学检测

评述了芯片毛细管电泳各种电化学检测尤其是安培检测中工作模式、工作电极、分离电流的消除、应用等方面的进展,并进行了展望。