Methane steam reforming over rhodium promoted Ni/Al2O3 catalysts

The effect of Rh addition upon catalyst characteristics and performance in methane steam reforming was investigated using Rh-promoted Ni/Al₂O₃ catalysts. The number of reduced metal atoms exposed on the surface increased for the Rh-promoted catalysts. Rh-promoted catalysts showed an increase in CH₄ reforming activity; however, constant turnover frequencies for promoted and unpromoted catalysts suggest that the increase in the number of metal surface atoms caused the activity enhancement. Rh also facilitated reduction of Ni/Al₂O₃.     

Reducibility of Mo species in Pt/MoO3 and PtMo/Al2O3 catalysis

Recucibility of Mo species in Pt/MoO₃ and PtMo/Al₂O₃ has been investigated by temperature-programmed reduction (TPR), temperature-programmed desorption of hydrogen (H₂-TPD) and temperature programmed electronic conductivity (TPEC) techniques. In Pt/MoO₃ at H₂ atmosphere, it was found by TPEC and TPR that, a slight amount of Pt could activate the transfer of the species and H atoms between H₂ and MoO₃, and thus accelerate the reduction of MoO₃. In PtMo/Al₂O₃, TPR and H₂-TPD revealed that the reduction of surface Mo species could also be facilitated by Pt. Two kinds of hydrogen molybdenum species were proposed on the surface of the catalyst after prereduction.     

The Al2O3-Fe2O3 Mixed Oxidic System, I. Preparation and Characterization

A series of Al₂O₃-Fe₂O₃ mixed oxidic solids with composition ranging from 0 to 100% of Fe₂O₃ were prepared and examined for structural characteristics. XRD diagrams showed the presence of α-Al₂O₃ and hematite phases. The analysis of M?ssbauer spectra revealed the existence of two iron containing phases. The specific surface area of the mixture decreases by the addition of iron and depends on the crystal phases of the mixture. This revised version was published online in June 2006 with corrections to the Cover Date.     

Al2O3-ZrO2复合膜的制备与表征

以异丙醇铝和氧氯化锆为原料,用溶胶-凝胶法在Al₂O₃中空纤维上制备了Al₂O₃-ZrO₂复合膜。应用TG、DTA、XRD、SEM等测试手段对复合膜的热稳定性、结构、形貌进行了表征。结果表明复合膜的热稳定性比单一由氧化铝或氧化锆制成的膜有显著的提高,在1100℃之前,复合膜以t-ZrO₂存在,1200℃时,出现了m-ZrO₂和α-Al₂O₃相。扫描电镜分析表明,膜表面完整、无缺陷。气体渗透实验进一步表明所得膜具有一定的气体选择性,0.3MPa和0.5MPa下对氮气和氩气的分离因子α分别为1.191和1.185,和氮气与氩气的理论分离因子(α=1.194)相当,说明气体通过膜的扩散以Knudsen扩散传质为主。用等温氮气吸附实验测定了非担载膜的孔径大小和分布,最可几孔径约为4.3nm。     

Preparation, characterization and application of KNH2/Al2O3 and KF/Al2O3 as strong solid bases

This review describes the preparation, characterization and application of KNH₂ loaded on alumina and KF loaded on alumina. These strong solid bases catalyze a variety of organic reactions in a very selective manner. The reactions include isomerizations of alkenes and alkynes, dimerization of alkynes, Tishchenko reaction, and the reaction of silanes to form of Si–C, Si–N and Si–O bonds.     

纳米膜组装介孔Al2O3：合成及Pt/Al2O3的硝基苯催化加氢性能

以"乙酸乙酯(EA)-偏铝酸钠-水"体系在室温下合成了纳米膜组装介孔Al2O3。研究发现:合成反应时间、静置前搅拌时间、NaAlO2用量、EA用量及反应温度等对合成产物的形貌有影响;另外,与用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂相比,纳米膜组装介孔Al2O3制备的Pt/Al2O3催化剂含有部分易被还原的PtOx物种。在硝基苯催化加氢反应中,用合成Al2O3为载体制备的Pt/Al2O3催化剂,比用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂具有更好的催化活性。     

Au/Al2O3纳米复合薄膜的制备和表征

用溶胶-凝胶法制备了Au/Al₂O₃纳米复合薄膜。利用X-射线衍射、X-射线光电子能谱、原子力显微镜以及紫外-可见光谱对薄膜的微观结构、表面形貌及光学性能进行了表征,研究表明:Au/Al₂O₃纳米复合薄膜是由纳米微晶组成的颗粒膜, 复合薄膜均匀、致密、无裂纹,Au以纳米晶核形式镶嵌于Al₂O₃基体中,纳米Au晶核的粒径为23～26nm;复合薄膜在可见光区有较强的吸收,吸收峰位置与烧结温度有关,吸收强度随烧结温度和金添加量增大而增大。     

Influence of the activation temperature on structural and textural properties of NiMo/Al2O3 hydrodesulfurization catalysts

Investigations of a commercial NiMo/Al₂O₃ hydrodesulfurization (HDS) catalyst are directed towards optimization of the activation procedure of HDS catalyst concerning active phase formation and thermal stability. Structural and textural data obtained with XRD, IR-FTIR, XPS and LTNA reveal that the optimal temperature for the formation of active species on the catalyst surface and an appropriate pore structure is 300°C.     

Ti∶Al2O3纳米粉体的共沉淀法合成及表征

本文采用共沉淀法合成了Ti∶Al2O3纳米粉体。利用热重/差热(TG/DTA)/X射线衍射(XRD)/红外光谱(FTIR)/扫描电镜(SEM)以及能谱(EDS)等分析方法对合成的Ti∶Al2O3纳米粉体进行了表征。结果分析表明:前驱体在1200℃下,保温1 h可以得到纯的α-Al2O3晶相;粉体的粒径均匀、分散性好,平均粒径在25~50 nm之间。     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

系列硅铝比纳米薄层ZSM-5分子筛的合成和表征

以自制不对称双子季铵盐表面活性剂为模板, 在水热合成体系中控制合成系列硅铝比纳米薄层ZSM-5分子筛.采用X射线衍射(XRD)、N₂吸附-脱附、X射线荧光光谱(XRF)、扫描电镜(SEM)和²⁷Al魔角旋转核磁共振(²⁷Al MAS-NMR)对合成的样品进行了表征. 详细研究了晶化温度、晶化时间、结构导向剂(SDA)用量、碱度等对合成的影响和纳米薄层ZSM-5分子筛的形成过程. 结果表明: 分子筛硅铝比越高, 结构导向剂用量越大, 所需的晶化时间越短; 晶化温度越高, 晶化时间越短; 且不同硅铝比纳米薄层ZSM-5分子筛的形貌规整度、比表面积和介孔/微孔孔容比例随着硅铝比而变化.     

水合氧化铝的热处理及纳米氧化铝的颗粒特性

利用IR、XRD、TG-DTA和TEM等测试技术研究了醇铝的水解产物——水合氧化铝的特性及水合氧化铝的热处理过程，探讨了热处理工艺对纳米氧化铝颗粒特性的影响规律。结果表明，醇铝的水解产物水合氧化铝为富含吸附水和结构水的非晶态一水铝石，300 ℃煅烧后出现部分非晶态γ-Al₂O₃；煅烧温度、保温时间和冷却方式均能影响纳米氧化铝粒子的晶型、大小和形貌，其中煅烧温度影响最大，冷却方式影响次之，保温时间影响最弱；在750 ℃ / 3 h、800 ℃ / 4 h、900 ℃ / 4 h、950 ℃ / 4 h和1 000 ℃ / 4 h随炉冷却工艺条件下，分别得到粒径为3~5 nm、3~5 nm、5~10 nm、10~15 nm和50~100 nm的纤维状或球状、α相或γ相的纳米氧化铝粒子。     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

Hydrogenation of nitrate in water over bimetallic Pd-Ag/Al2O3 catalysts

Hydrogenation of nitrate (NO₃ ⁻) in water was studied with 0.8 ×10⁻³–3.2 ×10⁻³ mol/dm³ of reactant in the temperature range of 293–313 K over palladium promoted Ag catalysts. Pd-Ag catalysts with a low ratio of Ag/Pd were characterized by high efficiency in the reduction of nitrates. The degradation of nitrates followed approximately first order decay and the estimated apparent activation energy was about 4 kJ/mol.     

不同磷含量对NiMoP/Al2O3加氢处理催化剂的影响

采用NiMoP浸渍液浸渍载体γ Al₂O₃制备了不同磷含量的NiMoP/Al₂O₃加氢处理催化剂。为了研究磷对该系列催化剂活性相结构的影响,用二苯并噻吩（DBT）和喹啉为模型化合物,考察了催化剂的加氢脱硫（HDS）和加氢脱氮（HDN）性能。结果表明,添加适当的磷能够提高催化剂的HDS和HDN活性,但是高含量的磷能显著的降低催化剂的催化性能。通过对催化剂进行XRD和HRTEM表征发现,添加磷能够增加MoS2的堆积层数以及Ⅱ型“Ni-Mo-S”相的相对含量,这是因为在制备过程中添加磷降低了活性组分与载体之间的相互作用。     

Thermal Stability of Pt/Al2O3 Catalysts Prepared by Sol-Gel

A series of Pt/Al₂O₃ catalysts were prepared using a sol-gel method. The influence of several parameters used in the synthesis including: metal content, identity of the metal precursor, and the water/alkoxide ratio on the structural properties of the fresh (dried) and calcined samples were studied. It was found that the BET surface area decreased with an increase in the platinum content. A surface area of 500 m²/g was obtained following calcination at 773 K. The structure of fresh samples as determined by FTIR corresponded to that of a pseudoboehmite structure. Samples prepared using a water/alkoxide ratio (H₂O/ATB) of 9 showed a well-defined, uniform pore size distribution following calcination at 773 K. Metal dispersions comparable to those obtained using impregnation methods were obtained. Aging studies (calcination at 873 K for 24 h) performed on these catalysts, exhibited sintering behavior which were similar to Pt/Al₂O₃ catalysts prepared by other methods. The sample prepared using a H₂O/ATB ratio of 9 had the highest surface area and was more thermally resistant towards metal sintering. A bimodal metal particle size distribution was observed: some particles exhibited sintering while others of similar size showed a greater thermal stability to sintering. The sample having the largest surface area and the highest thermal stability following thermal treatment was a consequence of a more condensed structure and a higher pore roughness obtained after drying the gel. This enabled the formation of an alumina structure which was more amorphous and limited aggregation of platinum particles due to surface diffusion within the pore structure.     

Copper-catalyzed arylation of phenylurea using KF/Al2O3

A mild and efficient method for the copper-catalyzed arylation of phenylurea is described. The coupling reaction of phenylurea with different functionalized aryl iodides in the presence of air stable CuI, N,N′-dibenzylethylenediamine as a ligand, and KF/Al₂O₃ as a base gives symmetrical and unsymmetrical diarylureas in relatively high yields.     

Mn / Ce / La / Al2O3催化剂中锰物种的精细结构研究

采用浸渍法制备了La、Ce助剂改性的γ-Al₂O₃负载锰氧化物催化剂，运用XANES、EXAFS、XRD、XPS和H₂-TPR等方法对催化剂的结构进行了表征，探讨了助剂对于催化剂中高分散Mn物种的精细结构、分散状态和存在形式的影响，并与样品的CO氧化活性相关联。XANES和EXAFS结果表明，500 ℃焙烧的样品中Mn物种主要以超细Mn₂O₃微晶形式存在，该物种由于高度分散使其配位对称性显著降低，无长程有序结构。TPR结果表明，样品中存在3种不同分散状态的表面Mn物种，即较难还原的Mn³⁺-O-Al³⁺相互作用物种，尺寸相对较大的三维分散的Mn₂O₃微晶，以及二维高度分散的Mn物种，后者是CO氧化反应的主要活性相。虽然Ce的加入使Mn物种的分散度有所降低，但Ce与Mn物种间的相互作用弱化了Mn-O键，加速了反应过程中活性氧物种的传递，提高了氧化还原循环的效率。同时，La的加入进一步促进了Ce物种在载体表面的分散，加强了Ce物种与Mn物种间的相互作用及催化协同性。     

Valence state of Mo and surface coverage of alumina by molybdenum-oxygen species in MoOx/Al2O3

CO₂ chemisorption, BET surface area and the degree of reduction of Mo(VI) (e/Mo) have been determined in MoO_x/Al₂O₃ samples, reduced with hydrogen at temperatures between 673 and 1173 K. The free alumina surface figures calculated from the surface area and e/Mo values were identical with those obtained from direct CO₂ chemisorption measurements. This identity indicates that all of the oxygen ions of the surface molybdenum-oxygen species block the alumina surface.     

Characterization and evaluation of Fe2O3/Al2O3 oxygen carrier prepared by sol–gel combustion synthesis

The sol-gel combustion synthesis (SGCS) for oxygen carrier (OC) to be used in chemical looping combustion (CLC) was first designed and experimented in this work, which is a new method of OC synthesis by combining sol-gel technique and solution combustion synthesis. Cheap hydrated metal nitrates and urea were adopted as precursors to prepare Fe₂O₃/Al₂O₃ OC at the molar ratio to unity (Fe1Al1), which was characterized through various means, including Fourier transforms infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffractor (XRD), and N₂ isothermal adsorption/desorption method. FTIR analysis on the chemical structure of the dried gel of Fe1Al1 indicated that urea was partly hydrolyzed and the hydrated basic carbonate was formed by the combination of groups such as (Fe(_1−yAl_y)_1−xO_1−3x, CO₃²⁻ and -OH-. By analyzing the staged products during SGCS, calcination was found as a necessary step to produce Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃. Through TGA-DTA, the decomposition of the dried gel was found to undergo five stages. The analysis of the evolved gases from the gel decomposition using FTIR partially confirmed the staged decomposition and assisted a better understanding of the mechanism of SGCS. XRD identification further substantiated the necessity of calcination to synthesize Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃, though it was not necessary for the synthesis of single phase α-Fe₂O₃ and α-Al₂O₃. Structural characterization performed on N₂ adsorption analyzer displayed that the pore shape of Fe1Al1 particles was heterogeneous. Finally, H₂ temperature-programmed reduction (TPR) of Fe1Al1 products in TGA indicated that the reduction reaction of Fe1Al1 OC after calcination was a single step reaction from α-Fe₂O₃ to Fe, and calcination benefited to improve the transfer rate of the lattice oxygen from the OC to fuel H₂. Furthermore, four times of reduction and oxidization (redox) reaction by alternating with H₂ and air demonstrated the synthesized OC had good reactivity and sintering-resistance, much suitable to be used in the realistic CLC. Overall, the SGCS method was found superior to other existent methods to prepare Fe₂O₃/Al₂O₃ OC for CLC application.