Global aerodynamic instability of twin cylinders in cross flow

This paper comprises an in-depth physical discussion of the flow-induced vibration of two circular cylinders in view of the time-mean lift force on stationary cylinders and interaction mechanisms. The gap-spacing ratio T/D is varied from 0.1 to 5 and the attack angle α from 0° to 180° where T is the gap width between the cylinders and D is the diameter of a cylinder. Mechanisms of interaction between two cylinders are discussed based on time-mean lift, fluctuating lift, flow structures and flow-induced responses. The whole regime is classified into seven interaction regimes, i.e., no interaction regime; boundary layer and cylinder interaction regime; shear-layer/wake and cylinder interaction regime; shear-layer and shear-layer interaction regime; vortex and cylinder interaction regime; vortex and shear-layer interaction regime; and vortex and vortex interaction regime. Though a single non-interfering circular cylinder does not correspond to a galloping following quasi-steady galloping theory, two circular cylinders experience violent galloping vibration due to shear-layer/wake and cylinder interaction as well as boundary layer and cylinder interaction. A larger magnitude of fluctuating lift communicates to a larger amplitude vortex excitation.     

Flow regimes and frequency selection of a cylinder oscillating in an upstream cylinder wake

This paper describes flow around a pair of cylinders in tandem arrangement with a downstream cylinder being fixed or forced to oscillate transversely. A sinusoidal parietal velocity is applied to simulate cylinder oscillation. Time-dependent Navier-Stokes equations are solved using finite element method. It is shown that there exist two distinct flow regimes: ‘vortex suppression regime’ and ‘vortex formation regime’. Averaged vortex lengths between the two cylinders, pressure variations at back and front stagnant points as well as circumferential pressure profiles of the downstream cylinder are found completely different in the two regimes and, thus, can be used to identify the flow regimes. It is shown that frequency selection in the wake of the oscillating cylinder is a result of non-linear interaction among vortex wakes upstream and downstream of the second cylinder and its forced oscillation. Increasing cylinder spacing results in a stronger oscillatory incident flow upstream of the second cylinder and, thus, a smaller synchronization zone.     

Numerical Study of the Flow Behind a Rotary Oscillating Circular Cylinder

A numerical study is performed of flow behind a rotationally oscillating circular cylinder in a uniform flow by solving the two-dimensional incompressible Navier-Stokes equations. The flow behavior in lock-on regime and the timing of vortex formation from the oscillating cylinder are studied. When the frequency of excitation of the cylinder is in the vicinity of the natural vortex formation frequency, a lock-on vortex formation regime appears. As the excitation frequency being increased relative to the natural frequency the initially formed vorticity concentration switches to the opposite side of the cylinder. The effects of oscillating frequency and amplitude on the vortex structures formed in the near wake of the cylinder are also investigated. Based on the present calculated results, some complicated vortex patterns are identified and are consistent with the previous experimental visualizations.     

Vibrations of a cylinder in a uniform flow in the presence of a no-slip side-wall

A circular cylinder placed in a uniform flow, and that spans the entire length between two side walls, may experience either parallel or oblique vortex shedding depending on the end conditions. It was shown by Mittal and Sidharth (2014) that the spatio-temporal periodicity of the oblique vortex shedding results in constant-in-time force experienced by the cylinder. On the contrary, parallel vortex shedding leads to fluid force that fluctuates with time. The free vibrations of a circular cylinder, in the presence of a wall, are investigated. For comparison, computations with end walls, where a slip condition on velocity is specified, are also carried out. The Reynolds number, based on the diameter of the cylinder and free-stream speed of the flow, is Re=100. The initial condition for the free vibrations is the fully developed unsteady flow past a stationary cylinder with oblique shedding. It is found that as the amplitude of vibration of the cylinder builds up, the vortices shed from the cylinder align with its axis leading to parallel shedding. The response of the cylinder is associated with two branches: initial and lower. On the lower branch, the response of the cylinder is virtually identical from two- and three-dimensional computations. The flow as well as the response is different on the initial branch and outside the synchronization regime. Forced vibrations confirm the phenomena.     

Wall proximity effects on the effectiveness of upstream control rod

Two dimensional flow over a circular cylinder with an upstream control rod of same diameter is simulated in unbound condition and in wall bounded conditions. The cylinders are placed at various heights from the wall and the inter-distance between cylinders is also varied. The control rod is subjected to different rotation rates. It is found that, in unbound condition, rotating the control rod decreases the critical pitch length (S/D_cr) and increases the drag and Strouhal number of the main cylinder. In presence of plane wall, the shielding provided by the separated shear layers from the control rod in cavity regime is deteriorated due to deflection of shear layers which results in higher drag and large fluctuation of lift coefficient. However, in wake impingement regime, the binary vortices from the control rod are weakened due to diffusion of vorticity and hence, the main cylinder experiences a lower drag and small lift fluctuations than that of unbound condition. The critical height of vortex suppression (H/D_cr) is higher in cavity regime than that of wake impingement regime due to the single extended-bluff body like configuration. The rotation of control rod energizes the wall boundary layer and increases the critical height of vortex suppression. Increasing the rotational rate of control rod decreases the drag force and reduces the amplitude of lift fluctuation. Analysis of the wall shear stress distribution reveals that it suffers a sudden drop at moderate height where the normal Karman vortex shedding changes to irregular shedding consisting of single row of negative vortices. Modal structures obtained from dynamic mode decomposition (DMD) reveal that the flow structures behind the main cylinder are suppressed due to wall and the flow is dominated by the wake of control rod.     

Critical Reynolds number and galloping instabilities: experiments on circular cylinders

The current paper considers large galloping-like vibrations of circular cylinders, generically inclined and yawed to the flow. The case of a round section prone to galloping is seemingly a paradox since rotational symmetry (or close to it) and classical galloping are apparently contradictory. Still there seems to be a range of wind speeds far from those for typical Kármán vortex shedding resonance where such a phenomenon does occur. Experimental results from both static and dynamic large-scale rigid cable models, presented here, show that this range coincides with the critical Reynolds number regime, where notable symmetry-breaking characteristics such as nonzero mean lift emerge. It is shown that a fundamental difference between the inclined and non-inclined cylinder aerodynamics may exist accommodating different pressure distributions and different resulting dynamic behaviours. Unsteady pressure measurements showing avalanche-like “jumps” and vortex dislocations building between cell structures in the cylinder spanwise direction are conjectured to be a key element in the unstable behaviour experienced.     

Resonance in flow past oscillating cylinder under subcritical conditions

Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes and hydrodynamics forces on the cylinder surface are systematically investigated. Special attention is paid to the phenomenon of resonance induced by the cylinder oscillation. The results demonstrate that vortex shedding can be excited extensively under subcritical conditions, and the response region of vibration frequency broadens with increasing Reynolds number and oscillation amplitude. Two distinct types of vortex shedding regimes are observed. The first type of vortex shedding regime(VSR I) is excited at low frequencies close to the intrinsic frequency of flow, and the second type of vortex shedding regime(VSR II)occurs at high frequencies with the Reynolds number close to the critical value. In the VSR I, a pair of alternately rotating vortices are shed in the wake per oscillation cycle,and lock-in/synchronization occurs, while in the VSR II, two alternately rotating vortices are shed for several oscillation cycles, and the vortex shedding frequency is close to that of a stationary cylinder under the critical condition. The excitation mechanisms of the two types of vortex shedding modes are analyzed separately.     

An experimental investigation into the effect of vortex generators on the near-wake flow of a circular cylinder

The effect of the streamwise vortex generators on the near-wake flow structure of a circular cylinder was experimentally investigated. Digital particle image velocimetry (DPIV) measurements were performed in a large circulating water tunnel facility at a Reynolds number of 41,300 where the flow around a bare cylinder was expected to be at the sub-critical flow state. In order to capture various flow properties and to provide a detailed wake flow topology, the DPIV images were analysed with three different but complementary flow field decomposition techniques which are Reynolds averaging, phase averaging and proper orthogonal decomposition (POD). The effect of the vortex generators was clearly demonstrated both in qualitative and in quantitative manner. Various topological features such as vorticity and stress distribution of the flow fields as well as many other key flow characteristics including the length scales and the Strouhal number were discussed in the study. To the best of the authors’ knowledge, the study presents the first DPIV visualization of the near-wake flow of a circular cylinder fitted with the vortex generators in the open literature.     

圆柱绕流流场结构的大涡模拟研究

为进一步揭示绕流现象的形成机理,本文分别对处于层流稳态区、尾流过渡区、剪切层转换区Re分别为26、200、1.4×105的三种典型流态下的单圆柱绕流进行了二维数值模拟研究。Re为26时应用层流模型直接求解N-S方程,而Re分别为200、1.4×105时使用大涡模拟的方法进行计算。数值模拟很好地再现了稳定的涡旋结构、周期性交替脱落的卡门涡街结构、不规则的涡旋结构,在此基础上分析了尾流结构的基本特征及其压强分布规律、平均的流场特性、积分参数(如升力系数、阻力系数、斯特劳哈尔等),并与有关研究成果进行了对比。研究发现,采用不同流动介质时流场特性有所差异,空气为介质时的计算结果更符合实验的成果,而水为介质时计算结果偏差较大,这主要是由尾流涡旋产生的不合理负压造成的。     

A numerical investigation of the flow over a pair of identical square cylinders in a tandem arrangement

This paper describes a numerical study of the two‐dimensional and three‐dimensional unsteady flow over two square cylinders arranged in an in‐line configuration for Reynolds numbers from 40 to 1000 and a gap spacing of 4D, where D is the cross‐sectional dimension of the cylinders. The effect of the cylinder spacing, in the range G = 0.3D to 12D, was also studied for selected Reynolds numbers, that is, Re = 130, 150 and 500. An incompressible finite volume code with a collocated grid arrangement was employed to carry out the flow simulations. Instantaneous and time‐averaged and spanwise‐averaged vorticity, pressure, and streamlines are computed and compared for different Reynolds numbers and gap spacings. The time averaged global quantities such as the Strouhal number, the mean and the RMS values of the drag force, the base suction pressure, the lift force and the pressure coefficient are also calculated and compared with the results of a single cylinder. Three major regimes are distinguished according to the normalized gap spacing between cylinders, that is, the single slender‐body regime (G < 0.5), the reattach regime (G < 4) and co‐shedding or binary vortex regime (G ≥4). Hysteresis with different vortex patterns is observed in a certain range of the gap spacings and also for the onset of the vortex shedding. Copyright © 2011 John Wiley & Sons, Ltd.     

Vortex shedding from a square cylinder in presence of a moving wall

A numerical study on the flow past a square cylinder placed parallel to a wall, which is moving at the speed of the far field has been made. Flow has been investigated in the laminar Reynolds number (based on the cylinder length) range. We have studied the flow field for different values of the cylinder to wall separation length. The governing unsteady Navier–Stokes equations are discretized through the finite volume method on a staggered grid system. A SIMPLE type of algorithm has been used to compute the discretized equations iteratively. A shear layer of negative vortex generates along the surface of the wall, which influences the vortex shedding behind the cylinder. The flow‐field is distinct from the flow in presence of a stationary wall. An alternate vortex shedding occurs for all values of gap height in the unsteady regime of the flow. The strong positive vortex pushes the negative vortex upwards in the wake. The gap flow in the undersurface of the cylinder is strong and the velocity profile overshoots. The cylinder experiences a downward force for certain values of the Reynolds number and gap height. The drag and lift are higher at lower values of the Reynolds number. Copyright © 2005 John Wiley & Sons, Ltd.     

Wake dynamics of external flow past a curved circular cylinder with the free-stream aligned to the plane of curvature

The fundamental mechanism of vortex shedding past a curved cylinder has been investigated at a Reynolds number of 100 using three-dimensional spectral/hp computations. Two different configurations are presented herein: in both cases the main component of the geometry is a circular cylinder whose centreline is a quarter of a ring and the inflow direction is parallel to the plane of curvature. In the first set of simulations the cylinder is forced to transversely oscillate at a fixed amplitude, while the oscillation frequency has been varied around the Strouhal value. Both geometries exhibit in-phase vortex shedding, with the vortex cores bent according to the body's curvature, although the wake topology is markedly different. In particular, the configuration that was found to suppress the vortex shedding in absence of forced motion exhibits now a primary instability in the near wake. A second set of simulations has been performed imposing an oscillatory roll to the curved cylinder, which is forced to rotate transversely around the axis of its bottom section. This case shows entirely different wake features from the previous one: the vortex shedding appears to be out-of-phase along the body's span, with straight cores that tend to twist after being shed and manifest a secondary spanwise instability. Further, the damping effect stemming from the transverse planar motion of the part of the cylinder parallel to the flow is no longer present, leading to a positive energy transfer from the fluid to the structure.     

Free v/s forced vibrations of a cylinder at low Re

Free vibrations of a circular cylinder of low non-dimensional mass are investigated at low Reynolds numbers. Computations are carried out for 5% blockage. Lock-in is observed for a range of Re and is accompanied with hysteresis at both lower as well as higher Re ends of the synchronisation/lock-in region. It is well known that the lock-in regime for free vibrations depends on the non-dimensional mass of the oscillator. The results from the present computations are compared with the data for forced vibrations from Koopmann (Journal of Fluid Mechanics, 28, 501–512, 1967) on a Y _max/D vs. f* plot, where Y _max is the maximum oscillation amplitude and f* is the ratio of cylinder vibration frequency to the vortex shedding frequency for a stationary cylinder. Good agreement is observed for the critical amplitude needed for onset of synchronisation between the forced and free vibrations. The results from the free vibrations are compared to the predictions from the linear oscillator model by assuming that the forces on the cylinder are unaffected as a result of vibrations. It is found that, for low mass oscillators, the modification of vortex shedding frequency and lift coefficient due to cylinder oscillations leads to the enhancement of the lock-in regime.     

FREE SURFACE WAVE INTERACTION WITH A HORIZONTAL CYLINDER

Classes of vortex formation from a horizontal cylinder adjacent to an undulating free-surface wave are characterized using high-image-density particle image velocimetry. Instantaneous representations of the velocity field, streamline topology and vorticity patterns yield insight into the origin of unsteady loading of the cylinder. For sufficiently deep submergence of the cylinder, the orbital nature of the wave motion results in multiple sites of vortex development, i.e., onset of vorticity concentrations, along the surface of the cylinder, followed by distinctive types of shedding from the cylinder. All of these concentrations of vorticity then exhibit orbital motion about the cylinder. Their contributions to the instantaneous values of the force coefficients are assessed by calculating moments of vorticity. It is shown that large contributions to the moments and their rate of change with time can occur for those vorticity concentrations having relatively small amplitude orbital trajectories. In a limiting case, collision with the surface of the cylinder can occur. Such vortex–cylinder interactions exhibit abrupt changes in the streamline topology during the wave cycle, including abrupt switching of the location of saddle points in the wave. The effect of nominal depth of submergence of the cylinder is characterized in terms of the time history of patterns of vorticity generated from the cylinder and the free surface. Generally speaking, generic types of vorticity concentrations are formed from the cylinder during the cycle of the wave motion for all values of submergence. The proximity of the free surface, however, can exert a remarkable influence on the initial formation, the eventual strength, and the subsequent motion of concentrations of vorticity. For sufficiently shallow submergence, large-scale vortex formation from the upper surface of the cylinder is inhibited and, in contrast, that from the lower surface of the cylinder is intensified. Moreover, decreasing the depth of submergence retards the orbital migration of previously shed concentrations of vorticity about the cylinder.     

Unsteady RANS and detached-eddy simulations of flow around a circular cylinder in ground effect

Unsteady Reynolds-averaged Navier–Stokes (URANS) simulations and detached-eddy simulations (DES) were performed of flow around a circular cylinder placed near and parallel to a moving ground, on which substantially no boundary layer developed to interfere with the cylinder. The results were compared with experiments previously reported by the authors to examine how accurately the URANS and DES can predict the cessation of von Kármán-type vortex shedding and the attendant critical drag reduction of the cylinder in ground effect. The DES, which were performed in a three-dimensional domain with spanwise periodicity imposed, correctly captured the cessation of the vortex shedding, whereas both two- and three-dimensional URANS also predicted it but at a much smaller gap-to-diameter ratio compared with the experiments. The wake structures of the cylinder predicted by the DES were in good agreement with the experiments in both large- and small-gap regimes, and also in the intermediate-gap regime, where the DES captured the intermittence of the vortex shedding in the near-wake region. Based on the results obtained, further discussions are also given to the reason why the von Kármán-type vortices in the URANS solutions incorrectly ‘survived’ until the cylinder came much closer to the ground.     

The turbulent flow field around a circular cylinder

The flow field around a circular cylinder mounted vertically on a flat bottom has been investigated experimentally. This type of flow occurs in several technical applications, e.g. local scouring around bridge piers. Hydrogen bubble flow visualization was carried out for Reynolds numbers ranging from 6,600 to 65,000. The main flow characteristic upstream of the cylinder is a system of horse-shoe vortices which are shed quasi-periodically. The number of vortices depends on Reynolds number. The vortex system was found to be independent of the vortices that are shed in the wake of the cylinder. The topology of the separated flow contains several separation and attachment lines which are Reynolds number dependent. In the wake region different flow patterns exist for each constant Reynolds number.     

Identification of flow regimes around two staggered square cylinders by a numerical study

The flow over two square cylinders in staggered arrangement is simulated numerically at a fixed Reynolds number (\(Re =150\)) for different gap spacing between cylinders from 0.1 to 6 times a cylinder side to understand the flow structures. The non-inclined square cylinders are located on a line with a staggered angle of \(45^{\circ }\) to the oncoming velocity vector. All numerical simulations are carried out with a finite-volume code based on a collocated grid arrangement. The effects of vortex shedding on the various features of the flow field are numerically visualized using different flow contours such as \(\lambda _{2}\) criterion, vorticity, pressure and magnitudes of velocity to distinguish the distinctive flow patterns. By changing the gap spacing between cylinders, five different flow regimes are identified and classified as single body, periodic gap flow, aperiodic, modulated periodic and synchronized vortex shedding regimes. This study revealed that the observed multiple frequencies in global forces of the downstream cylinder in the modulated periodic regime are more properly associated with differences in vortex shedding frequencies of individual cylinders than individual shear layers reported in some previous works; particularly, both shear layers from the downstream cylinder often shed vortices at the same multiple frequencies. The maximum Strouhal number for the upstream cylinder is also identified at \({G}^{*}=1\) for aperiodic flow pattern. Furthermore, for most cases studied, the downstream cylinder experiences larger drag force than the upstream cylinder.     

Development of the instability of an axisymmetric vortex flow in a circular cylinder

A vortex structure consisting of two concentric vortex rings located in a circular cylinder is studied. The rings touch each other and have a uniform vorticity. The geometric and dynamic parameters of the rings satisfy the condition of zero total intensity. A linear stability analysis of this structure is performed, including the limiting cases when the inner ring transforms into a circle or the outer ring is adjacent to the boundary of the cylinder. The results of numerical simulation of the evolution of unsteady flows are presented for a wide range of variation of governing parameters of the problem. It is established that the evolution of unstable vortex flows results in the formation of several types of quasistationary structures, the topology of which depends mainly on the dominant disturbance mode.     

Spanwise correlations in the wake of a circular cylinder and a trapezoid placed inside a circular pipe

The spanwise correlation of a circular cylinder and a trapezoidal bluff body placed inside a circular pipe in fully developed turbulent regime is studied using hotwire anemometer. The present configuration possesses complex fluid structure interaction owing to the following features: high blockage effect; low aspect ratio of the body; upstream turbulence and interaction of axisymmetric flow with a two dimensional bluff body. The spatial correlation of such configuration is seldom reported in the literature. Results are presented for Reynolds number of Re_D=1×10⁵. Three different blockage ratios (0.14, 0.19 and 0.28) are considered in the present study. Correlation coefficient is observed to improve with increase in blockage ratio. Compared to a circular cylinder, a trapezoidal bluff body possesses high correlation length. The near wall effects tend to increase the phase drift, which is reflected in low correlation coefficients close to the pipe wall. The results show that the simultaneous effect of curvature, low aspect ratio and upstream turbulence reduces the correlation coefficients significantly as compared to unconfined and confined (parallel channel) flows. The low frequency modulations with a circular cylinder are higher for lower blockage ratios. The three-dimensionality of vortex shedding for trapezoid with a blockage ratio of 0.28 was observed to be lower compared to circular cylinder and all other blockage ratios. Low frequency modulations were found to be responsible for weak vortex shedding from a circular cylinder compared to a trapezoidal bluff body. The vortex shedding is observed to be nearly two dimensional in case of a trapezoidal bluff body of blockage ratio 0.28.     

On vortex shedding from low aspect ratio dual step cylinders

A dual-step cylinder is comprised of two cylinders of different diameters. A large diameter cylinder (D) with low aspect ratio (L/D) is attached to the mid-span of a small diameter cylinder (d). The present study investigates the effect of Reynolds number (Re_D) and L/D on dual step cylinder wake development for D/d=2, 0.2≤L/D≤3, and two Reynolds numbers, Re_D=1050 and 2100. Experiments have been performed in a water flume facility utilizing flow visualization, Laser Doppler Velocimetry (LDV), and Particle Image Velocimetry (PIV). The results show that vortex shedding occurs from both the large and small diameter cylinders for 1≤L/D≤3 at Re_D=2100 and 2≤L/D≤3 at Re_D=1050. At these conditions, large cylinder vortices predominantly form vortex loops in the wake and small cylinder vortices form half-loop vortex connections. At lower aspect ratios, vortex shedding from the large cylinder ceases, with the dominant frequency in the large cylinder wake attributed to the passage of vortex filaments connecting small cylinder vortices. At these lower aspect ratios, the presence of the large cylinder induces periodic vortex dislocations. Increasing L/D increases the frequency of occurrence of vortex dislocations and decreases the dominant frequency in the large cylinder wake. The identified changes in wake topology are related to substantial variations in the location of boundary layer separation on the large cylinder, and, consequently, changes in the size of the vortex formation region. The results also show that the Reynolds number has a substantial effect on wake vortex shedding frequency, which is more profound than that expected for a uniform cylinder.