Flow structure in a flat vortex chamber

We investigate a flow in a flat vortex chamber in which the distance between the end walls is smaller than the radius of the chamber. The study was mainly performed by optical methods: a Töpler device was employed, with the Foucault knife replaced by a diaphragm. It is shown that the flow in the chamber has a complicated spatial structure. In addition to the basic helical flow, an intense “transverse” rotation of the type of Taylor-Görtler vortices occurs. In contrast to previously studied flows, where these vortices were observed near a concave surface, in the motion considered transverse vortices occur in the entire working volume of the chamber. In this case, four parallel vortex filaments are formed. The high intensity of the vortices has allowed one to visualize them by the Töpler method and by “tinting” the flow by highly disperse particles. Quantitative dependences of the dimensions of the vortex cells on the flow regime, i.e., on the pressure of gas deceleration, were obtained.     

Discretization of the vorticity field of a planar jet

In data assimilation, information from sensors is used to correct the state variables of a numerical model. This has been used to great advantage by the weather prediction community in the context of direct numerical simulation (DNS) models, but has seen comparatively little use in point-vortex models. This is due in large part to data-processing issues. In order to keep up with the speeds necessary for effective data assimilation, one must extract and discretize the vortex structures from velocity field data in a computationally efficient fashion—i.e., using as few discrete vortices as possible to model the measured flow. This paper describes a new strategy for accomplishing this and evaluates the results using data from a laboratory-scale vortex-dominated planar jet. Large-scale vortex structures are found using a family of variants on traditional vortex extraction methods. By augmenting these methods with simple computational topology techniques, one obtains a new method that finds the boundaries of the coherent structures in a manner that naturally follows the geometry of the flow. This strategy was evaluated in the context of two standard vortex extraction methods, vorticity thresholding and Okubo–Weiss, and tested upon velocity field data from the experimental fluid flow. The large-scale structures found in this manner were then modeled with collections of discrete vortices, and the effects of the grain size of the discretization and the parameters of the discrete vortex model were studied. The results were evaluated by comparing the instantaneous velocity field induced by the discrete vortices to that measured in the jet. These comparisons showed that the two extraction techniques were comparable in terms of sensitivity and error, suggesting that the computationally simpler vorticity thresholding method is more appropriate for applications where speed is an issue, like data assimilation. Comparisons of different discretization strategies showed that modeling each large-scale vortex structure with a single discrete vortex provided the best compromise between mean-squared error and computational effort. These results are of potential interest in any situation where one must balance accuracy and expense while extracting vortices from a snapshot of a flow field; data assimilation is only one example.     

Formation of a tripolar vortex in a stratified fluid

This paper reports on an experimental study of vortices in a stratified fluid. The vortices were generated by two different stirring devices, viz. a rotating sphere and a rotating bent rod. It was found that the vortices created with the rotating sphere are mostly axisymmetric and stable, whereas the vortices produced with the bent rod generally show instabilities, under certain conditions leading to the formation of a tripolar vortex. This report concentrates on this tripolar structure and presents quantitative information about the flow obtained through streak photography of tracer particles.     

Population,characteristics and kinematics of vortices in a confined rectangular jet with a co-flow

Vortex behavior and characteristics in a confined rectangular jet with a co-flow were examined using vortex swirling strength as a defining characteristic. On the left side of the jet, the positively (counterclockwise) rotating vortices are dominant, while negatively rotating vortices are dominant on the right side of the jet. The characteristics of vortices, such as population density, average size and strength, and deviation velocity, were calculated and analyzed in both the cross-stream direction and the streamwise direction. In the near-field of the jet, the population density, average size and strength of the dominant direction vortices show high values on both sides of the center stream with a small number of counter-rotating vortices produced in the small wake regions close to jet outlet. As the flow develops, the wake regions disappear, these count-rotating vortices also disappear, and the population of the dominant direction vortices increase and spread in the jet. The mean size and strength of the vortices decrease monotonically with streamwise coordinate. The signs of vortex deviation velocity indicate the vortices transfer low momentum to high-velocity region and high momentum to the low velocity region. The developing trends of these characteristics were also identified by tracing vortices using time-resolved particle image velocimetry data. Both the mean tracked vortex strength and size decrease with increasing downstream distance overall. At the locations of the left peak of turbulent kinetic energy, the two-point spatial cross-correlation of swirling strength with velocity fluctuation and concentration fluctuation were calculated. All the correlation fields contain one positively correlated region and one negatively correlated region although the orientations of the correlation fields varied, due to the flow transitioning from wake, to jet, to channel flow. Finally, linear stochastic estimation was used to calculate conditional structures. The large-scale structures in the velocity field revealed by linear stochastic estimation are spindle-shaped with a titling stream-wise major axis.     

Dynamics of hairpin vortices generated by a mixing tab in a channel flow

To better understand mixing by hairpin vortices, time-series particle image velocimetry (PIV) was applied to the wake of a trapezoidal-shaped passive mixing tab mounted at the bottom of a square turbulent channel (Re _h =2,080 based on the tab height). Instantaneous velocity/vorticity fields were obtained in sequences of 10 Hz in the tab wake in the center plane (x–y) and in a plane (x–z) parallel to the wall. Periodically-shed hairpin vortices were clearly identified and seen to rise as they advected downstream. Experimental evidence shows that the vortex-induced ejection of the near-wall viscous fluid to the immediate upstream is important to the dynamics of hairpin vortices. It can increase the strength of the hairpin vortices in the near tab region and cause generation of secondary hairpin vortices further downstream when the hairpin heads are farther away from the wall. Measurements also reveal the existence of a type of new secondary vortice with the opposite-sign spanwise vorticity. The distribution of vortex loci in the x–y plane shows that the hairpin vortices and the reverse vortices are spatially segregated in distinct layers. Turbulence statistics, including mean velocity profiles, Reynolds stresses, and turbulent kinetic energy dissipation rate distributions, were obtained from the PIV data. These statistical quantities clearly reveal imprints of the identified vortex structures and provide insight into mixing effectiveness. Received: 24 February 2000/Accepted: 24 October 2000     

Vortex shedding induced by a solitary wave propagating over a submerged vertical plate

Experimental study was conducted on the vortex shedding process induced by the interaction between a solitary wave and a submerged vertical plate. Particle image velocimetry (PIV) was used for quantitative velocity measurement while a particle tracing technique was used for qualitative flow visualization. Vortices are generated at the tip of each side of the plate. The largest vortices at each side of the plate eventually grow to the size of the water depth. Although the fluid motion under the solitary wave is only translatory, vortices are shed in both the upstream and downstream directions due to the interaction of the generated vortices as well as the vortices with the plate and the bottom. The process can be divided into four phases: the formation of a separated shear layer, the generation and shedding of vortices, the formation of a vertical jet, and the impingement of the jet onto the free surface. Similarity velocity profiles were found both in the separated shear layer and in the vertical jet.     

Dynamics of prolate jellyfish with a jet-based locomotion

Swimming jellyfish deliver momentum to the surrounding fluid in the form of vortices. A three-dimensional computational model was adopted to investigate the characteristic flow patterns produced by jellyfish with a jet-based locomotion and the process of vortex generation. The interaction between jellyfish and the surrounding fluid may be simulated using the immersed boundary method. The vortex structures generated in the wake were elucidated in detail. The vortices were formed due to the contraction and expansion of the elastic bell. A dimensionless temporal parameter was employed to analyze the vortex formation process. During the early stage of contraction, the vortices were dominantly generated by the stroke. The ejected fluid from the inside of the bell was then entrained into the vortices, thereby decreasing the vorticity at the core and increasing the total circulation within the vortex ring. The Froude propulsion efficiency increased as the vortex formation number increased, implying that the propulsion in the way of growing the vortex structures was favorable in terms of the efficiency.     

Volumetric three-component velocimetry measurements of the turbulent flow around a Rushton turbine

Volumetric three-component velocimetry measurements have been taken of the flow field near a Rushton turbine in a stirred tank reactor. This particular flow field is highly unsteady and three-dimensional, and is characterized by a strong radial jet, large tank-scale ring vortices, and small-scale blade tip vortices. The experimental technique uses a single camera head with three apertures to obtain approximately 15,000 three-dimensional vectors in a cubic volume. These velocity data offer the most comprehensive view to date of this flow field, especially since they are acquired at three Reynolds numbers (15,000, 107,000, and 137,000). Mean velocity fields and turbulent kinetic energy quantities are calculated. The volumetric nature of the data enables tip vortex identification, vortex trajectory analysis, and calculation of vortex strength. Three identification methods for the vortices are compared based on: the calculation of circumferential vorticity; the calculation of local pressure minima via an eigenvalue approach; and the calculation of swirling strength again via an eigenvalue approach. The use of two-dimensional data and three-dimensional data is compared for vortex identification; a ‘swirl strength’ criterion is less sensitive to completeness of the velocity gradient tensor and overall provides clearer identification of the tip vortices. The principal components of the strain rate tensor are also calculated for one Reynolds number case as these measures of stretching and compression have recently been associated with tip vortex characterization. Vortex trajectories and strength compare favorably with those in the literature. No clear dependence of trajectory on Reynolds number is deduced. The visualization of tip vortices up to 140° past blade passage in the highest Reynolds number case is notable and has not previously been shown.     

Stability of the crossflow pattern around a slender and influence of disturbance

Topological structure and stability of a slender cross flow is discussed by the stability theory of dynamic system. The inner boundary of flow field was limiting streamline and it was proved that the topological structure connected saddles by limiting streamline is stable. It is proved that the development of slender vortices leads to the change of topological structure about cross flow. And it is the change from stable and symmetrical vortices flow pattern to unstable and symmetrical vortices flow pattern, and then to stable and asymmetrical vortices flow pattern due to little disturbance which leads to the development of asymmetrical slender vortices. The influence of disturbance to flowfield structure was discussed by unfolding theory too.     

Direct simulation of breakdown to turbulence following oblique instability waves in a supersonic boundary layer

The late stages of transition to turbulence in a Mach two boundary layer are investigated by direct numerical simulation of the compressible Navier-Stokes equations. The primary instability at this Mach number consists of oblique waves, which are known to form a pattern of quasi-streamwise vortices. It is found that breakdown does not follow immediately from these vortices, which decay in intensity. The generation of new vortices is observed by following the evolution of the pressure and vorticity in the simulation, and analysed by consideration of vorticity stretching. It is found that the slight inclined and skewed nature of the quasi-streamwise vortices leads to a production of oppositely signed streamwise vorticity, which serves as a strong localised forcing of the shear layer alongside the original vortices, formed by convection and stretching of spanwise vorticity. The shear layer rolls up into many new vortices, and is followed by a sharp increase in the energy of higher frequencies and in the skin friction.     

Large eddy simulation with direct resolution of subgrid motion using a grid free vortex particle method

The paper presents a novel Large Eddy Simulation approach with a direct resolution of the subgrid motion of fine concentrated vortices. The method, proposed first by Kornev (2018), is based on combination of a grid based and the grid free computational vortex particle (VPM) methods. The large scale flow structures are simulated on the grid whereas the concentrated structures are modeled using VPM. Due to this combination the advantages of both methods are strengthened whereas the disadvantages are diminished. The procedure of the separation of small concentrated vortices from the large scale ones is based on LES filtering idea. The flow dynamics is governed by two coupled transport equations taking two-way interaction between large and fine structures into account. The fine structures are mapped back to the grid if their size grows due to diffusion. Algorithmic aspects specific for three dimensional flow simulations are discussed. Validity and advantages of the new approach are illustrated for a well tried benchmark test of the decaying homogeneous isotropic turbulence using the experimental data of Comte-Bellot and Corrsin (1971).     

Transition phenomena in the wake of a square cylinder

The transition phenomena in the wake of a square cylinder were investigated. The existence of mode A and mode B instabilities in the wake of a square cylinder was demonstrated. The critical Reynolds numbers for the inception of these instability modes were identified through the determination of discontinuities in the St–Re curves, and were found to have mean values of 160 and 204 for the onset of mode A and B instabilities, respectively. The spectra and time traces of the wake streamwise velocity component were found to display three distinct patterns in laminar, mode A and mode B flow regimes. Streamwise vortices with different wavelength at various Reynolds numbers were observed through different measures. The symmetries and evolution of the secondary vortices were observed using laser-induced-fluorescent dye. It was found that, just like the case of a circular cylinder, the secondary vortices from the top and bottom rows were out-of-phase with each other in the mode A regime, but in-phase with each other in the mode B regime. From the flow visualization, it was qualitatively proven that there is stronger interaction between braid regions in the mode B regime. At the same time, analysis of PIV measurements quantitatively demonstrated the presence of the stronger cross flow in mode B regime when compared to the mode A regime. It suggests that the in-phase symmetry of the mode B instability is the result of strong interaction between the top and bottom vortex rows. It was also observed that although the vorticity of the secondary vortices in the mode A regime was smaller, its circulation was more than twice that of mode B instability. Compared to primary vortices, the circulations of both mode A and mode B vortices were much smaller, which indicates that the secondary vortices most likely originate from the primary vortices. The wavelengths of the streamwise vortices in the mode A and B regimes were measured using the auto-correlation method, and were found to be 5.1 (±0.1)D, 1.3 (±0.1)D, and 1.1 (±0.1)D at Re=183 (mode A), 228 and 377 (both mode B), respectively. From the present investigation, mode A instability was likely to be due to the joint-effects of the deformation of primary vortex cores and the stretching of vortex sheets in the braid region. On the other hand, mode B instability was thought to originate from the “imprinting” process.     

Measurements of the aperiodic wake of a hovering rotor

 An experimental investigation was made to study the aperiodic flow characteristics of the tip vortices generated by one-bladed and two-bladed hovering rotors. Measurements of the tip vortex locations and accompanying aperiodicity statistics were established as a function of vortex age. Velocity field measurements were made using three-component laser Doppler velocimetry. The average amplitude of the aperiodicity was found to be a fraction of the measured viscous core radius, this being approximately 5% of blade chord or about 50% of the core radius for wake ages of less than two rotor revolutions. The aperiodicity appeared isotropic. A numerical analysis of the aperiodicity problem based on convolution with an assumed displacement probability function showed that for this experiment the measured tangential velocities in the tip vortices were underestimated by approximately 20% and the viscous core radii were overestimated by 20%. There was no evidence that the number of blades or the blade passage adversely influenced the aperiodicity of the rotor tip vortices. Received: 22 August 1997/Accepted: 4 February 1998     

Evolution of Concentrated Vortices in a Viscous Fluid

Evolution of the vortices of monopole and dipole types in a viscous fluid is considered numerically. Theory and numerical results are compared for some particular exact solutions. A good agreement is obtained for the dipole vortices (viscous Chaplygin-Lamb vortices) moving with variable velocities due to viscosity. For the monopole type vortices, the agreement is more or less good only at an initial stage of their evolution; while in the long-lime asymptotics the law of vorticity decay other than the theoretical one is discovered. The reason for such a discrepancy is discussed. The interactions of dipole vortices with each other and with rigid boundaries are studied too. The stability of dipole vortices with complex internal structures is considered briefly.     

Vortex body interaction in a jet—circular cylinder sound generating system

An experimental investigation was conducted on relations between a ‘sound’ ^* and vortices generated by a plane Jet impinging on a circular cylinder. The ‘sound’ was a pseudo sound or near-field pressure fluctuations because its measurement was made at positions not sufficiently far from the Jet and the cylinder. The vortices consisted of vortices formed in the impinging jet and vortices shed from the cylinder. A thin splitter plate was attached to the downstream side of the cylinder to modify the shed vortices. The nature of the shed vortices was shown to have a significant influence on the intensity and frequency of the ‘sound’. The intensity of the ‘sound’ was found to be related to the streamwise extent of distributed vorticity within the vortices; that is, the more compact the vortices, the stronger was the ‘sound’.     

Investigation of the spectrum of short-wave Görtler vortices in a gas

The linear stage of short-wave Görtler vortices in the boundary layer near a concave surface is studied for the regime of weak hypersonic viscid-inviscid interaction at high Reynolds and Görtler numbers. It is assumed that the gas is perfect and the viscosity is a linear function of the enthalpy. It is found that neutral vortices are located near the surface if it has zero temperature. When the surface is heated, the vortices move away from it, whereas all newly incipient vortices are located near the surface. It is shown that the growth rate of the vortices has a maximum and the heating of the surface has a stabilizing effect on the vortices.     

Three-component velocity field measurements of propeller wake using a stereoscopic PIV technique

A stereoscopic PIV (Particle Image Velocimetry) technique was used to measure the three-dimensional flow structure of the turbulent wake behind a marine propeller with five blades. The out-of-plane velocity component was determined using two CCD cameras with an angular displacement configuration. Four hundred instantaneous velocity fields were measured for each of four different blade phases, and ensemble averaged in order to find the spatial evolution of the propeller wake in the region from the trailing edge up to one propeller diameter (D) downstream. The influence of propeller loading conditions on the wake structure was also investigated by measuring the velocity fields at three advance ratios (J=0.59, 0.72 and 0.88). The phase-averaged velocity fields revealed that a viscous wake formed by the boundary layers developed along the blade surfaces. Tip vortices were generated periodically and the slipstream contracted in the near-wake region. The out-of-plane velocity component and strain rate had large values at the locations of the tip and trailing vortices. As the flow moved downstream, the turbulence intensity, the strength of the tip vortices, and the magnitude of the out-of-plane velocity component at trailing vortices all decreased due to effects such as viscous dissipation, turbulence diffusion, and blade-to-blade interaction.     

Nonlinear characteristics of a thin wing in a shock-free flow around the nose

An effective means of controlling wing leading-edge stall at high angles of attack is deflection of the nose in order to assure shock-free entrance of the stream. A numerical method of computing the angles of nose deflection and the aerodynamic characteristics of a thin wing of arbitrary planform for a shock-free entrance of the steady ideal incompressible fluid stream is elucidated in this paper on the basis of nonlinear wing theory [1]. The problem is solved by the method of discrete vortices. In the computations, the wing and its wake, replaced by a vortex sheet, are modeled by a system of discrete vortices which are nonlinear segments with constant circulation along the length. The angles of deflection of the nose and the aerodynamic characteristics of the wing, including shunting of the free vortices shed from the side and trailing edges, are determined during the computation. Examples of an electronic digital computer are presented.     

Coherent structure in the turbulent wake behind a circular cylinder

A wake behind a circular cylinder at Reynolds number 850–1700 was visualized by the smoke-wire method. The observations of the How together with the results of quantitative measurements, such as various velocity correlation coefficients, illustrated the formation process of spoon-shaped large eddies in the region 90 ⩽x/d⩽ 230 attained through the deformation and rearrangement of the regular Karman vortices. A spoon vortex was likely to pair with the counterpart on the opposite side of the wake. The large-scale bulges of the turbulent and non-turbulent interface of the wake were shown to correspond to these spoon vortices.These results indicate that some coherent structures are organized by rearrangement and deformation of initially regular vortices in turbulent flow.     

PIV measurements of the near-wake behind a sinusoidal cylinder

The three-dimensional near-wake structures behind a sinusoidal cylinder have been investigated using a particle image velocimetry (PIV) measurement technique at Re=3,000. The mean velocity fields and spatial distributions of ensemble-averaged turbulence statistics for flows around the sinusoidal and corresponding smooth cylinders were compared. The near-wake behind the sinusoidal cylinder exhibited pronounced spanwise periodic variations in the flow structure. Well-organized streamwise vortices with alternating positive and negative vorticity were observed along the span of the sinusoidal cylinder. They suppress the formation of the large-scale spanwise vortices and decrease the overall turbulent kinetic energy in the near-wake of the sinusoidal cylinder. The sinusoidal surface geometry significantly modifies the near-wake structure and strongly controls the three-dimensional vortices formed in the near-wake.