BaZr(BO3)2:Eu的合成及发光性能研究

用硝酸盐热分解法成功制备了BaZr(BO₃)₂:Eu(Eu³⁺的掺杂量为摩尔分数5％)荧光材料，并研究了其在254及147nm光束激发下的发光特性.254nm光束激发下的发射主峰位于612nm处，归属于Eu³⁺的⁵D₀—⁷F₂的电偶极跃迁，但在147nm光束激发下的发射主峰位于592nm处，归属于Eu³⁺的相似文献   

Gd2O3:Eu3+纳米晶的燃烧合成及光致发光性质

采用柠檬酸作燃烧剂用燃烧合成法制备了Gd₂O₃:Eu³⁺纳米晶.用X射线衍射仪(XRD)、高分辨透射电子显微镜(HRTEM)和荧光分光光度计等对Gd₂O₃:Eu³⁺纳米晶的结构、形貌和发光性能进行了分析.结果表明：不同柠檬酸与稀土离子配比(C/M)制备的样品经800℃ 退火1 h后，均得到了纯立方相的Gd₂O₃:Eu³⁺纳米晶，晶粒尺寸约为30 nm，尺寸分布较窄，其中以C/M=1.0时制备的纳米晶结晶性最好，发光强度最大.Gd₂O₃:Eu³⁺纳米晶主发射峰位置均在612 nm处 (⁵D₀→⁷F₂跃迁)，激发光谱中电荷迁移态发生红移，观察到Gd³⁺向Eu³⁺的有效能量传递.对柠檬酸与稀土离子配比(C/M)对结晶度、发光性质等的影响也进行了分析和讨论.     

Eu3+掺杂的α-Gd2(MoO4)3荧光粉合成与表征

采用固相反应法合成了Eu³⁺掺杂的α-Gd₂(MoO₄)₃荧光粉。通过XRD、SEM以及激发和发射光谱对样品进行了研究,结果发现助熔剂为3%时样品的结晶较好,样品的发光强度最强,并且样品粉末不团聚。光谱测量的结果表明该荧光粉与其他商品荧光粉不同,其最有效的激发波长不在电荷迁移带范围,其f-f跃迁的465,395nm吸收更强,这就意味着该类荧光粉可作为目前已商品化的白光LED的红色补偿荧光粉,也可作为近紫外LED和三基色荧光粉组合型白光器件的红色荧光粉的候选材料。     

La2Zr2O7:Eu3+纳米棒的合成、表征及其荧光性能

采用传统固相法和水热法成功地制备出棒状La₂Zr₂O₇:Eu³⁺荧光粉. 利用X射线粉末衍射仪、透射电镜和荧光光谱仪等分析了产物的结构、形貌和发光特性. 结果表明红色荧光粉La₂Zr₂O₇:Eu³⁺有良好的晶相,属于立方结构,空间点群为Fd3m; 其形貌主要为纳米棒, 平均直径约47 nm, 长度为50～700 nm. 并对纳米棒的生长机理进行了探讨. 在466 nm蓝光激发下,La₂Zr₂O₇:Eu³⁺荧光粉能发射出Eu³⁺的特征红色荧光,发射主峰位于616 nm处,归属于Eu³⁺的⁵DO_→⁷F2_{超灵敏电偶极跃迁.此外,在产物的发射光谱中能够观察到⁵D}1_→⁷FJ _{(J=0, 1, 2)跃迁和⁵D}1_→⁷FJ _{(J=1, 2, 4)跃迁的劈裂峰,这说明Eu³⁺处在低对称性的晶体场格位中.}     

Ba10(PO4)4(SiO4)2∶Eu2+荧光体的光谱特性

采用高温固相法合成了荧光体Ba₁₀（PO₄）₄（SiO₄）₂：Ce³⁺和Ba₁₀（PO₄）₄（SiO₄）₂：Eu²⁺,研究了两种荧光体的光谱特性。结果表明,两者都呈现较强的宽带激发特征。根据同种基质中Eu²⁺和Ce³⁺两种离子光谱特征的相关性,通过测得的Ba₁₀（PO₄）₂（SiO₄）₂基质中Ce³⁺的光谱数据估算了Ba₁₀（PO₄）₂（SiO₄）₂：Eu²⁺中Eu²⁺的斯托克斯位移（ΔS）和激发能量,估算结果与Ba₁₀（PO₄）₂（SiO₄）₂：Eu²⁺样品的光谱分析结果十分吻合。Ba₁₀（PO₄）₂（SiO₄）₂：Eu²⁺可以同时被紫光和蓝光激发,发出偏白的绿光,可用作白光LED的荧光粉。     

白光LED用LiBaBO3:Eu2+材料发光特性研究

采用高温固相法制备了LiBaBO₃:Eu²⁺绿色发光材料.测量了Eu²⁺浓度为1mol%时样品的激发与发射光谱,其发射光谱为双峰宽谱,主峰分别为482和507nm,与理论计算值符合很好;监测482nm发射峰时,对应激发光谱的峰值为287和365nm,监测507nm发射峰时,对应的激发峰为365和405nm.研究了Eu²⁺浓度对材料发射光谱的影响,结果显示,随Eu²⁺浓度的增大,蓝、绿发射峰均发生了     

用于白光LED的单一基质白光荧光粉Ca2SiO3Cl2:Eu2+，Mn2+的发光性质

用高温固相法合成了Eu²⁺，Mn²⁺共激活的Ca₂SiO₃Cl₂高亮度白色发光材料，并对其发光性质进行了研究. 该荧光粉在近紫外光激发下发出强的白色荧光，Eu^{2+中心形成峰值为419 nm和498 nm的特征宽带，通过Eu2+中心向Mn2+中心的能量传递导致了峰值为578 nm的发射，三个谱带叠加从而在单一基质中得到了白光. 激发光谱均分布在250—415 nm的波长范围，红绿蓝三个发射带的激发谱峰值分别位于385 nm，412 nm，370 nm和396 nm处，可以被InGaN管芯产生的紫外辐射有效激发. Ca₂SiO₃Cl₂:Eu2+，Mn2+是一种很有前途的单一基质白光LED荧光粉.}     

掺Er3+的NaY(WO4)2晶体的光谱特性

测量了Er:NaY(WO4)2晶体的吸收光谱、激发光谱、发射光谱以及上转换发光,并对测量的结果进行了详细分析,得出了Er:NaY(WO4)2晶体的光学特性.解释了离子间的能级跃迁过程 关键词： Er:NaY(WO4)2晶体 Er3+ 吸收光谱 激发光谱 发射光谱 上转换     

第一原理研究Sn(O1-xNx)2材料的光电磁性质

基于第一原理的密度泛函理论, 以量子化学从头计算软件 为平台研究了Sn(O_1-xN_x)₂材料的光电磁性能, 分析了体系的态密度、 能带结构、 磁性、 介电虚部及折射率. 计算结果表明, N替代O后, 随着掺杂浓度的增加, 体系的带隙先减小后增大, 掺杂量为12.50%时带隙最窄. 由于N 2p轨道电子的贡献, 在0.55-1.05 eV范围内产生了浅受主能级, 价带和导带处的能级均出现了劈裂及轨道的重叠现象, Sn-O键的键强大于N-O键的键强. 从磁性来看, N原子决定了磁矩的大小. 从介电虚部可知, 掺杂后体系的光学吸收边增宽, 主跃迁峰发生红移, 反射率和介电谱相对应, 各峰值与电子的跃迁吸收有关.     

特定位点上CO2与(TiO2)n团簇相互作用的第一性原理研究

本文基于密度泛函理论系统地研究了(TiO₂)_n团簇上二氧化碳(CO₂)的吸附和活化性质. 计算结果表明,CO₂更倾向于吸附在(TiO₂)_n团簇的桥氧原子上,形成“化学吸附”碳酸盐络合物. 而CO更倾向于吸附到末端Ti-O的Ti原子上. 发现计算得到的碳酸盐振动频率值与实验获得的结果非常吻合,这表明配合物中CO₂的几何构型与其线性型相比,有微小的弯转. 通过对电子结构、电荷密度、电离势、HOMO-LUMO以及态密度的分析,证实了CO₂与团簇之间的电荷转移以及相互作用. 从预测的能量分布图来看,(TiO₂)_n团簇上的CO₂活化与结构密切有关,相比于块体的TiO₂,CO₂在团簇结构上更易于吸附和活化.     

Ionic liquid-assisted hydrothermal synthesis of dendrite-like NaY(MoO4)2:Tb phosphor

Micro-sized NaY(MoO₄)₂:Tb³⁺ phosphors with dendritic morphology was synthesized by a ionic liquid-assisted hydrothermal process. X-ray diffraction (XRD) indicated that the as-prepared product is pure tetragonal phase of NaY(MoO₄)₂. Field emission scanning electron microscopy (FE-SEM) images showed that the as-prepared NaY(MoO₄)₂:Tb³⁺ phosphors have dendritic morphology. The photoluminescent (PL) spectra displayed that the as-prepared NaY(MoO₄)₂:Tb³⁺ phosphors show a stronger green emission with main emission wavelength 545 nm corresponding to the ⁵D₄→⁷F₅ transition of Tb³⁺ ion, and the optimal Tb³⁺ doping concentration for obtaining maximum emission intensity was confirmed to be 10 mol%. Based on Van Uitert's and Dexter's models the electric dipole–dipole (D–D) interaction was confirmed to be responsible for the concentration quenching of ⁵D₄ fluorescence of Tb³⁺ in the NaY(MoO₄)₂:Tb³⁺ phosphors. The intrinsic radiative transition lifetime of ⁵D₄ level is found to be 0.703 ms.     

Tm3+离子掺杂的钨酸钇钠晶体中浓度猝灭效应的研究

测量了Tm³⁺离子不同浓度(0.5at.%, 3 at.%, 5 at.%)掺杂的NaY(WO₄)₂晶体在800nm激光二极管激发下的上转换发射光谱.结合吸收谱、荧光谱和由Judd-Ofelt理论计算的光谱参数，详细分析了Tm³⁺:NaY(WO₄)₂晶体中上转换能量传递机理和离子浓度对上转换发射的影响.讨论了四种影响上转换发光效率的离子间相互作用机理：³H₅+¹G₄→³H₆+¹D₂，³H₅+³H₅→³H₆+³F₃，¹G₄+³H₆→³F₄+³F₃，¹G₄+³H₆→³F₃+³F₄，并根据Miyakawa-Dexter理论定量计算了各过程的发生概率.论证了交叉弛豫和共协上转换等浓度猝灭效应是影响Tm³⁺离子蓝色上转换荧光发射效率的主要因素. 关键词： 3+离子')" href="#">Tm³⁺离子 4)₂晶体')" href="#">NaY(WO₄)₂晶体 上转换 浓度猝灭     

Hydrothermal Synthesis of Rhombus-like SmCO3OH Microplates and Its Photoluminescence Property Doped with Eu3+

以尿素为沉淀剂,用水热法合成了厚约1.5 μm、边长为5～10 μm的SmCO₃OH菱形微米片,并通过XRD、场发射扫描电子显微镜、傅里叶变换红外光谱和X射线电子能谱对该产物的结构与性能进行了表征．另外,研究了Eu³⁺掺杂SmCO₃OH菱形微米片的光致发光性能,在677 nm处得到了一个宽而强的发射光．     

Spectral characterization and energy levels of Cr:Sc2(MoO4)3 crystal

This paper reports the spectral properties and energy levels of Cr³⁺:Sc₂(MoO₄)₃ crystal. The crystal field strength Dq, Racah parameter B and C were calculated to be 1408 cm⁻¹, 608 cm⁻¹ and 3054 cm⁻¹, respectively. The absorption cross sections σ_α of ⁴A₂→⁴T₁ and ⁴A₂→⁴T₂ transitions were 3.74×10⁻¹⁹ cm² at 499 nm and 3.21×10⁻¹⁹ cm² at 710 nm, respectively. The emission cross section σ_e was 375×10⁻²⁰ cm² at 880 nm. Cr³⁺:Sc₂(MoO₄)₃ crystal has a broad emission band with a broad FWHM of 176 nm (2179 cm⁻¹). Therefore, Cr³⁺:Sc₂(MoO₄)₃ crystal may be regarded as a potential tunable laser gain medium.     

试验优化设计Tm3+/Yb3+共掺钼酸钇钠荧光粉上转换发光性质的研究

为得到最大发光强度的Tm³⁺/Yb³⁺共掺钼酸钇钠荧光粉, 采用试验优化设计的方法建立发光强度与Tm³⁺/Yb³⁺掺杂浓度的回归方程, 再通过遗传算法优化算出方程的最大解. 利用高温固相法制备出了该解的Tm³⁺/Yb³⁺共掺钼酸钇钠荧光粉样品. 在980 nm抽运激发下, 测量了样品的上转换荧光发射谱, 分析了上转换发光机制, 在室温下观察到强烈的蓝光(476 nm)和微弱的红光(649 nm)发射, 其分别对应于Tm³⁺的¹G₄→³H₆ 和¹G₄ →³F₄ 跃迁. 在Tm³⁺/Yb³⁺ 上转换发光体系中, ¹G₄ 的上转换可见发射是双光子合作上转换能量传递过程. 并探讨了样品的温度效应, 发现该样品蓝光发光强度随温度升高而减弱, 并对其温度猝灭机理进行了解释. 关键词： 试验优化设计 上转换 钼酸钇钠 3+/Yb³⁺')" href="#">Tm³⁺/Yb³⁺     

Conversion of infrared radiation into visible emission in NaY(WO4)2:Yb, Ho crystal

The spectroscopic characteristics and fluorescence dynamics for Yb³⁺/Ho³⁺:NaY(WO₄)₂ crystal were investigated. The parameters of oscillator strengths, the spontaneous transition probabilities, the fluorescence branching ratios, the radiative lifetimes and the stimulated emission cross sections have been calculated based on Judd-Ofelt theory and Füchtbauer-Ladenburg method. The energy transfer efficiency from Yb³⁺ to Ho³⁺ was 65.85%. The green emission (530-570 nm) corresponding to (⁵F₄, ⁵S₂)→⁵I₈ transition, red emission (640-670 nm) due to ⁵F₅→⁵I₈ transition and NIR emission (740-770 nm) attributed to (⁵F₄, ⁵S₂)→⁵I₇ transition were observed on 974 nm excitation at room temperature. Under low pump power, the intensity of green light emission is weaker than that of the red light, while under high pump power, the case is on the contrary. The upconversion is based on the two-photon process either the energy transfer from Yb³⁺ ions or by the excited state absorption. The proposed mechanisms of upconversion emissions were provided.     

Er3+，Tm3+共掺的NaY(WO4)2晶体的光谱分析和上转换发光

在室温下，测量了Er:Tm:NaY(WO₄)₂晶体的吸收光谱、激发光谱、发射光谱以及上转换发光，并运用J-O理论对测量的结果进行了计算，得出了Er:Tm:NaY(WO₄)₂晶体的强度参数.报道了Tm，Er离子间特殊的能量传递和相关上转换，解释了离子间的能级跃迁过程.同时，对于Er增强Tm离子近红外发光的特性也作了充分研究. 关键词： 4)₂晶体')" href="#">Er:Tm:NaY(WO₄)₂晶体 吸收光谱 发射光谱 激发光谱 上转换     

Exchange charge model and analysis of the microscopic crystal field effects in KAl(MoO4)2:Cr

In the present paper, we report on consistent crystal field calculations of the Cr³⁺ ions energy levels in KAl(MoO₄)₂ using actual D_3d site symmetry of the Cr³⁺ position and employing the exchange charge model (ECM) of the crystal field. In addition to the energy level calculations, the Huang-Rhys factor S=5.7 and effective phonon energy ?ω=268 cm^-1 were evaluated in the single configurational coordinate model. Detailed treatment of the microscopic crystal field effects in the ECM framework allowed to obtain analytical dependence of the crystal field strength 10Dq on the Cr-O interionic distance and extracting from it the values of some parameters of the electron-vibrational interaction (EVI) in the KAl(MoO₄)₂:Cr³⁺ system. All obtained results are compared with experimental data and discussed; agreement between the calculated and experimental parameters is good.     

Eu3+掺杂的Sr2CeO4发光材料的光致发光研究

利用高温固相反应法制备了Eu³⁺掺杂的Sr₂CeO₄样品,并对其吸附水前后的光谱特性进行了研究.结果发现,对于刚制备的Sr_2-xEu_xCeO_4+x/2样品, 在Ce⁴⁺—O^2-的电荷迁移激发中,只有强激发带(～35700cm^-1)与Eu³⁺离子间存在能量传递,而弱激发带 (～29400cm^-1)只是引起Ce⁴⁺—O^2-的电荷迁移发射;在Sr_2-xEu_xCeO_4+x/2样品吸附水后,Eu³⁺的线状吸收跃迁强度显著增加, Ce⁴⁺—O^2-两个激发带均向Eu³⁺离子传递能量. Ce⁴⁺—O^2-强激发带通过交换作用向Eu³⁺离子传递能量,而弱激发带与Eu³⁺离子间的能量传递机理是非辐射多极子近场力的相互作用. 关键词： 2-xEu_xCeO_4+x/2')" href="#">Sr_2-xEu_xCeO_4+x/2 发光性质 能量传递 吸附水     

Synthesis and characterization of Sr3Al2O6：Eu2＋, Dy3＋ phosphors prepared by sol-gel-combustion processing

A type of red luminescent Sr3Al2O6:Eu2+, Dy3+ phosphor powder is synthesised by sol-gel-combustion processing, with metal nitrates used as the source of metal ions and citric acid as a chelating agent of metal ions. By tracing the formation process of the sol-gel, it is found that it is necessary to reduce the amount of NO3- by dropping ethanol into the solution for forming a stable and homogeneous sol-gel. Thermogravimetric and Differential Scanning Calorimeter Analysis, x-ray diffractionmeter, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the luminescent properties of the as-synthesised Sr3Al2O6:Eu2+, Dy3+. The results reveal that the Sr3Al2O6 crystallises completely when the combustion ash is sintered at 1250 C. The excitation and the emission spectra indicate that the excitation broadband lies mainly in a visible range and the phosphors emit a strong light at 618 nm under the excitation of 472 nm. The afterglow of (Sr0.94Eu0.03Dy0.03)3Al2O6 phosphors sintered at 1250 ℃ lasts for over 1000 s when the excited source is cut off.