Plasma-based sputtering of indium tin oxide for the application of photovoltaic cells

Transparent and conducting indium tin oxide (ITO) thin films were deposited on soda lime glass substrates by RF plasma magnetron sputtering at room temperature. The effect of thickness (100, 200 and 300?nm) on the physical (structural, optical, electrical) properties of ITO thin films was investigated systematically. It is observed that with an increase in thickness, the X-ray diffraction data indicate polycrystalline films with grain orientations predominantly along (222) and (400) directions; the average grain size increases from 10 to 30?nm; the optical band gap increases from 3.68 to 3.73?eV and the transmission decrease from 80% to 70% . Four-point probes show a low resistivity (2.4×10^?5?Ω?cm) values for film with a thickness 300?nm. Present work shows that the ITO is a promising transparent conductive oxide material for the solar cell application.     

Highly transparent and conductive indium tin oxide thin films for solar cells grown by reactive thermal evaporation at low temperature

Transparent conductive tin-doped indium oxide (In₂O₃:Sn, ITO) thin films with various Sn-doping concentrations have been prepared using the low cost reactive thermal evaporation (RTE) technique at a low growth temperature of ~160 °C. The structural characteristics, optical and electrical properties of the ITO thin films were investigated. These polycrystalline ITO films exhibited preferential orientation along (222) plane and possessed low resistivities ranging from 3.51 to 5.71 × 10^?4 Ω cm. The decreased mobility was attributed to the scattering by ionized and neutral impurities at high doping concentrations. The optimized ITO thin film deposited with 6.0 wt% Sn-doping concentration exhibited a high average transparency of 87 % in the wavelength range of 380–900 nm and a low resistivity of 3.74 × 10^?4 Ω cm with a high Hall mobility of 47 cm² V^?1s^?1. A hydrogenated amorphous silicon and silicon–germanium (a-Si:H/a-SiGe:H) double-junction solar cell fabricated with the RTE-grown ITO electrodes presented a conversion efficiency of 10.51 %.     

Angular-dependent photoemission studies of indium tin oxide surfaces

Indium tin oxide (ITO) surfaces were treated by solvent cleaning, by plasma of oxygen, argon, nitrogen and by argon ion (Ar⁺) sputtering. Angular-dependent X-ray photoelectron spectroscopy (ADXPS) and ultraviolet photoelectron spectroscopy (UPS) were used to determine the chemical composition, the chemical states and the work function after each treatment. It was found that oxygen plasma and nitrogen plasma chemically reacted with the ITO surfaces. Yet little etching of the surface can be observed after plasma treatments. Among all treatments, oxygen-plasma-treated ITO achieved the highest work function of 4.40 eV, whereas Ar⁺-sputtered ITO surface had the lowest work function of 3.90 eV. The stoichiometry of the ITO surface is shown to be the major controlling factor of the ITO work function. Received: 7 February 2000 / Accepted: 28 March 2000 / Published online: 13 September 2000     

Metal oxide buffer layer for improving performance of polymer solar cells

We report the application of aluminum doped ZnO (ZnO:Al) layer as a buffer on ITO glass for fabrication of non-inverted polymer solar cells. The ZnO:Al thin film was deposited using DC magnetron sputtering, with the thickness being varied from 23 to 100 nm. The devices showed most discernible improvements in their efficiencies when a thin layer of ZnO:Al film of thickness ∼40 nm was introduced. The observed enhancement in short circuit current density and open circuit voltage is likely attributed to the role of the ZnO:Al film as an optical tuner and an interfacial diffusion barrier. The result suggests that a metal oxide layer inserted between ITO and polymer layers can be a route for improving both efficiency and stability of polymer solar cells.     

Photovoltaic properties of ferroelectric solar cells based on polycrystalline BiFeO3 films sputtered on indium tin oxide substrates

To study the ferroelectric photovoltaic effect based on polycrystalline films,preparation of high-quality polycrystalline films with low leakage and high remnant polarization is essential.Polycrystalline Bi Fe O3(BFO)thin films with extremely large remnant polarization(2Pr=180μC/cm2)were successfully deposited on glass substrates coated with indium tin oxide using a modified radio frequency magnetron sputtering method.Symmetric and asymmetric cells were constructed to investigate the ferroelectric photovoltaic effect in order to understand the relationship between polarization and photovoltaic response.All examined cells showed polarization-induced photovoltaic effect.Our findings also showed that the ferroelectric photovoltaic effect is highly dependent on the material used for the top electrode and the thickness of the polycrystalline film.     

Investigation on the thermal radiation properties of antimony doped tin oxide particles

This paper reports the preparation of antimony doped tin oxide crystalline powders by chemical coprecipitation method. The influence of sintering temperature and the sintering retention time on the thermal infrared emissivity is analysed. The thermal infrared reflectivity is measured and the optimum doping concentration is proposed.     

Substrate-assisted laser patterning of indium tin oxide thin films

Maskless laser patterning of indium tin oxide (ITO) thin films was studied by the use of a diode-pumped Q-switched Nd:YLF laser. The ITO films were sputter-deposited either on lime glass, the standard substrate material for flat panel display applications, or fused quartz so that the efficiency of laser patterning as a function of substrate absorption could be studied. The laser wavelength was varied among infrared (5=1047 nm), visible (5=523 nm), and ultraviolet (5=349 nm and 5=262 nm). It is observed that strong light absorption by the substrate is a crucial requirement for a residue-free patterning of the ITO film. Observations and numerical calculations of the laser-induced surface temperature indicate that material removal occurs via thermal vaporization and that other mechanisms such as photochemical decomposition or spallation can be neglected.     

A simplified reactive thermal evaporation method for indium tin oxide electrodes

Indium tin oxide (ITO) films approximately 120 nm thick were deposited onto unheated glass substrates by using reactive thermal evaporation (RTE) and in situ post-evaporation annealing in oxygen. We show that this simplified method can be used to produce high quality ITO thin films with low electrical resistivity (10⁻³ Ω cm) and high transmittance (approximately 80% at 550 nm). The refractive index is approximately 2.0 and the direct optical band gap of the films (above 3.0 eV) is in good agreement with previously reported values. Since this deposition method does not require heating the substrates or furnace annealing at high temperatures, it can be advantageous when it is necessary to decrease the thermal budget on underlying devices or layers.     

Reduced graphene oxide field-effect transistor with indium tin oxide extended gate for proton sensing

In this study, the reduced graphene oxide field-effect transistor (rGO FET) with indium tin oxide (ITO) extended gate electrode was demonstrated as a transducer for proton sensing application. In this structure, the proton sensing area of the ITO extended gate electrode is isolated from the active area of the rGO FET. The proton sensing properties based on the rGO FET transducer were analyzed. The rGO FET device with encapsulation by a tetratetracontane (TTC) layer showed good stability in electrolytic solutions. The device showed an ambipolar behavior with shifts in Dirac point as the pH of the electrolyte is varied. The pH sensitivity based on the Dirac point shift as a sensing parameter was about 43–50 mV/pH for a wide range of pH values from 2 to 12. The ITO extended gate rGO FET may be considered a potential transducer for sensing of H⁺ in electrolytes. Its sensing area can be modified further for various ions sensing applications.     

Laser-driven high-resolution patterning of indium tin oxide thin film for electronic device

We here introduce a laser-driven process to pattern transparent thin films on transparent substrates. This method utilizes a pre-patterned metal film as the dynamic release layer and the transparent thin film is selectively removed by a thermo-elastic force laser-induced in the underlying metal layer. High-fidelity indium tin oxide (ITO) thin film patterns were fabricated on plastic and glass substrates using a pulsed Nd:YAG laser. Tens of square centimeters could be patterned with several pulse shots. We fabricated a pentacene thin film transistor with ITO source and drain electrodes and observed a very low off-current level. This tells that the channel area between ITO electrodes was completely etched out by this laser-driven process. Combined with the absence of photoresist and chemical etching steps, this method provides a simple high-resolution route to pattern transparent thin films over large areas at low temperatures.     

Electrical and optical properties of Si-doped indium tin oxides as transparent electrode and anti-reflection coating for solar cells

We have studied the electrical and optical properties of Si-doped indium tin oxides (ITSOs) as transparent electrodes and anti-reflection coatings for Si-based solar cells. The ITSO thin films were obtained by co-sputtering of ITO and SiO₂ targets under target power control. The resistivity of the ITSO thin films deposited at 0.625 in terms of power ratio (ITO/SiO₂) were 391 Ωcm. In this condition, the ITSO thin films showed very high resistivity compared to sputted pure ITO thin films (1.08 × 10⁻³ Ωcm). However, refractive index of ITSO thin films deposited at the same condition at 500 nm is somewhat lowered to 1.97 compared to ITO thin films (2.06). The fabricated graded refractive index AR coatings using ITO, ITSO, and SiO₂ thin films kept over 80% of transmittance regardless of their thickness varing from 97 nm to 1196 nm because of their low extinction coefficient. As the AR coating with graded refractive indices using ITO, ITSO, and SiO₂ layers was applied to general silicon-based solar cell, the current level increased nearly twice more than that of bare silicon solar cell without AR coating.     

ITO导电膜红外发射率理论研究

根据红外辐射理论和薄膜光学原理计算了高品质ITO(indium tin oxide)导电膜的红外发射 率,其理论曲线与实测曲线基本符合. 并得出方块电阻小于30Ω时,ITO膜在红外波段8—14μ m的平均红外发射率理论值小于0.1.实际制备方块电阻小于10Ω的ITO膜具有优良的红外隐身 性能. 讨论了高品质ITO膜具有低红外发射率的物理机理,并提出了低红外发射率临界方块电 阻值,这有利於理论研究和工艺制备红外隐身ITO膜. 关键词： 红外发射率 ITO薄膜 理论计算 方块电阻     

The insert of zinc oxide thin film in indium tin oxide anode for organic electroluminescence devices

Zinc oxide films were prepared by rf magnetron sputtering on glass substrates with designed ZnO target using high-purity of zinc oxide (99.99%) powder. Systematic study on dependence of target-to-substrate distance (D_ts) on structural, electrical and optical properties of the as-grown ZnO films was mainly investigated in this work. XRD showed that highly preferred ZnO crystal in the [0 0 1] direction was grown in parallel to the substrate, while the D_ts did not effect to the peak position of XRD. With decreasing D_ts, the growth rate is increased while the electrical resistivity as well as crystal size in the ZnO films was decreased. The XPS data showed that the O/Zn ratio in ZnO films was increased with increasing D_ts in the films. The as-grown ZnO films have an average transmittance of above 85% at the visible region. The optical band gap of the as-grown ZnO films was changed from 3.18 to 3.36 eV with D_ts. With decreasing D_ts, the electrical resistivity was decreased, while the growth rate was increased.A bilayer is used as an anode electrode for organic electroluminescent devices. The bilayer consists of an ultrathin ZnO layer adjacent to a hole-transporting layer and an Indium tin oxide (ITO) outerlayer. We tried to bring low the barrier between the devices as deposited ZnO films on ITO substrates. We fabricated the organic EL structure consisted of Al as a cathode, Al₂O₃ as an electro transport layer, Alq₃ as a luminously layer, TPD as a hole transport layer and ZnO (1 nm)/ITO (150 nm) as an anode. The result of this experiment was not good compared with the case of using ITO, nevertheless, at this structure we obtained the lowest turn-on voltage as the value of 19 V and the good brightness (6200 cd/m²) of the emission light from the devices. Then the quantum efficiency was to be 1.0%.     

Surface preparation and characterization of indium tin oxide substrates for organic electroluminescent devices

Received: 10 March 1998 / Accepted: 21 September 1998 / Published online: 24 February 1999     

Indium tin oxide thin films by bias magnetron rf sputtering for heterojunction solar cells application

In this investigation ITO thin films were prepared by bias magnetron rf sputtering technique at substrate temperature of 180 °C and low substrate-target distance for future a-Si:H/c-Si heterojunction (HJ) solar cells application. Microstructure, surface morphology, electrical and optical properties of these films were characterized and analyzed. The effects of ion bombardments on growing ITO films are well discussed. XRD analysis revealed a change in preferential orientation of polycrystalline structure from (2 2 2) to (4 0 0) plane with the increase of negative bias voltage. Textured surface were observed on AFM graphs of samples prepared at high negative bias. Hall measurements showed that the carrier density and Hall mobility of these ITO films are sensitive to the bias voltage applied. We attributed these effects to the sensitivity of energy of Ar⁺ ions bombarding on growing films to the applied bias voltage in our experiments. At last the figure of merit was calculated to evaluate the quality of ITO thin films, the results of which show that sample prepared at bias voltage of −75 V is good to be used in HJ cells application.     

反应离子镀制备ITO膜

采用反应离子镀新工艺成功地在K9玻璃上制备了ITO(Indium Tin Oxide)透明导电膜,所制备的ITO膜在550～600nm波长范围内,典型的峰值透过率为89%,面电阻为34Ω/□。     

A cast seed-mediated growth method for preparing gold nanoparticle-attached indium tin oxide surfaces

An effective approach to attach gold nanoparticles (AuNPs) directly on indium tin oxide (ITO) surface with higher density is reported. The attachment was carried out using a cast seed-mediated growth method, which was revised from our previous seed-mediated growth approach. The cast seeding with three-cycles of the drop of the seed solution containing Au nano-seed particles and the evaporation at 30 °C followed by the treatment in the growth solution containing HAuCl₄, cetyltrimethylammonium bromide (CTAB) and ascorbic acid was found to be suitable to prepare the AuNPs attached ITO surfaces having higher density and narrower size distribution. The 10-cycles cast seeding formed the connected or networked nanostructures of AuNPs, though the optical properties were different from those of the dispersed AuNP-attached ITO. The present cast seeding approach provides a facile and useful strategy to attach AuNPs on the surface without the use of certain organic binder molecules.     

后退火处理对铟锡氧化物表面等离激元共振特性的影响

近年来,表面等离激元光子学发展迅速,并取得了众多新成果.重掺杂半导体材料的表面等离激元共振性质的研究,也得到了人们越来越多的关注.本文通过纳米球刻印技术制备准三维二氧化硅纳米球阵列,在阵列上沉积铟锡氧化物薄膜,通过不同条件下的后退火处理改变铟锡氧化物薄膜的载流子浓度和载流子迁移率,并研究随着材料性质的改变其相应表面等离激元共振特性的变化规律.结果表明：退火处理均使铟锡氧化物薄膜的晶粒长大,光学透过率增加;在空气中退火会导致铟锡氧化物薄膜的载流子浓度减少,其表面等离激元共振峰红移;而真空退火则使铟锡氧化物薄膜的载流子浓度增加,共振峰蓝移.这些研究结果可为后续铟锡氧化物表面等离激元材料及器件的研究提供科学依据和实际指导.