Characterization of CO2 Plasma and Interactions with Polypropylene Film

The interactions between CO₂ plasma, less degrading than O₂ plasma, and polymeric surfaces are studied. CO₂ discharge and the relationships between the density of plasma reactive species are analyzed by optical emission spectroscopy and mass spectrometry. The optical emission spectrum was identified and five principal systems of carbon monoxide were assigned: the 4th and 3rd positive systems, Angstrom and 3A systems. Other systems dealing with ionized species CO⁺ ₂ and CO⁺ were also found. Mass spectrometry showed that the carbon monoxide and atomic oxygen were created through CO₂ dissociation by electronic impact. The detected molecular oxygen coming from the atomic oxygen recombination was associated with the power. The study of plasma/polymer interface showed the consumption of ionized species, the appearance of atomic hydrogen due to methyl groups transformation into exomethylene groups onto the polypropylene surface, and a degradation mechanism dependent on atomic oxygen density in the plasma phase.     

On the use of actinometric emission spectroscopy in SF6-O2 radiofrequency discharges: Theoretical and experimental analysis

A comparison of the results obtained by solving the Boltzmann equation with the experimental results from optical emissions obtained in SF₆-O₂ radiofrequency discharges, when N₂, Ar, and He are also admitted as actinometers, has allowed us to explore the potentialities and limits of actinometry. The use of different actinometers also allowed us to monitor the evolution of the electron distribution functions as a function of the plasma parameters.     

Characterization of an argon-hydrogen microwave discharge used as an atomic hydrogen source. Effect of hydrogen dilution on the atomic hydrogen production

This work is devoted to the study of an argon-hydrogen microwave plasma used as an atomic hydrogen source. Our attention has focused on the effect of the hydrogen dilution in argon on atomic hydrogen production. Diagnostics are performed either in the discharge or in the post-discharge using emission spectroscopy (actinometry) and mass spectrometry. The agreement between actinometry and mass spectrometry diagnostics proves that actinometry on the Ha(656.3 nm) and Hβ(486.1 nm) hydrogen Balmer lines can be used to measure the relative atomic hydrogen density within the microwave discharge. Results show that the atomic hydrogen density is maximum for a gas mixture corresponding to the partial pressure ratioP _{H 2}/P _Ar range between 1.5 and 2. The variation of atomic hydrogen density can be explained by a change of the dominant reactive mechanisms. At a low hydrogen partial pressure the dominant processes are the charge transfers with recombinations between Ar⁺ and H₂ which lead to ArH⁺ and H ₂ ⁺ ion formation. Both ions are dissociated in dissociative electron attachment processes. At a low argon partial pressure the electron temperature and the electron density decrease with increasing partial pressure ratio. The dominant mechanisms become direct reactions between charged particles (e, H⁺, H ₂ ⁺ , and H ₃ ⁺ ) or excited species H(n=2) with H₂ producing H atoms.     

Development of core–shell structure Fe3O4@Ta2O5 microspheres for selective enrichment of phosphopeptides for mass spectrometry analysis

Protein phosphorylation is one of the most important post-translational modifications. Due to the dynamic nature and low stoichiometry of the protein phosphorylation, enrichment of phosphopeptides from proteolytic mixtures is often necessary prior to their characterization by mass spectrometry. Many metal oxides such as titanium dioxide and zirconium dioxide have been successfully applied to isolation and enrichment of phosphopeptides. Recently, niobium pentoxide was proved to have the ability for selective enrichment of phosphopeptides. Considering the proximity of tantalum to niobium, we supposed that Ta₂O₅ can be used as affinity probes for phosphopeptide enrichment. In the work, we synthesized Fe₃O₄@Ta₂O₅ magnetic microspheres with core–shell structure for selective enrichment of phosphopeptides. To demonstrate its ability for selective enrichment of phosphopeptides, we applied Fe₃O₄@Ta₂O₅ magnetic microspheres to isolation and enrichment of the phosphopeptides from tryptic digestion of standard proteins and real samples, and then the enriched peptides were analyzed by matrix-assisted laser desorption mass spectrometry analysis (MALDI-MS) or liquid chromatography coupled to electrospray ionization mass spectrometry (LC–ESI-MS). Experiment results demonstrate that Ta₂O₅ coated-magnetic microspheres show the excellent potential for selective enrichment of phosphopeptides.     

Copper(II) complexes with hydroxyl-containing dipeptides glycyl- L -serine and L -seryl- L -tyrosine

Dipeptides glycyl- _L -serine and _L -seryl– _L -tyrosine are tridentate ligands in coordination with Cu(II) through their NH₂?, N–(from deprotonated amide group) and O–atom (by COO- group), forming [Cu^II(LH_?1)H₂O]. The forth position of square-planar geometry of Cu²⁺ is occupied by H₂O as terminal ligand. Solid-state linear dichroic IR-spectroscopy, UV-Vis, mass spectrometry with ESI and FAB, tandem mass spectrometry (HPLC-MS/MS), TGV and DSC methods, EPR and magnetochemistry data prove the formation of five-membered chelate rings with participation of Cu²⁺ both in solution and in solid state.     

Accuracy in the Isotope Dilution Mass Spectrometry of Uranium in Rubidium Uranium Sulphate Rb2U(SO4)3

Abstract

Problems encountered in the determination of uranium in rubidium uranium sulphate (Rb₂U(SO₄)₃) employing isotope dilution thermal ionisation mass spectrometry (ID-TIMS) are discussed. The positive bias of 0.2 to 0.3% in the determination of uranium in Rb₂U(SO₄)₃ by ID-TIMS with respect to the stoichiometric composition has been resolved by modifying the chemical exchange procedures. The concentration of uranium in Rb₂U(SO₄)₃ could be determined with an accuracy better than 0.1% employing the HClO₄ treatment for proper isotopic exchange between the spike and sample isotopes.     

MnO_2/NiCo_2O_4的静电自组装合成及其电化学性能

通过带负电荷的MnO2纳米片与带正电荷的Co-Ni层状双氢氧化物(LDHs)纳米片的静电自组装外加后续热处理合成了异质层状结构的MnO2/NiCo2O4复合物.采用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、拉曼光谱、原子吸收光谱(AAS)、场发射扫描电镜(FESEM)和透射电子显微镜(TEM)对其结构和形貌进行了表征.用循环伏安(CV)、恒流充放电和电化学交流阻抗技术对其电化学性能进行了测试.研究结果表明,该方法制得的异质复合物具有多孔层状堆垛结构,这种特殊的结构不仅增大了电解液离子的接触面积,而且还为其嵌入-脱出提供了有效途径.该复合物在1 A·g-1电流密度时,-0.6-0.45 V电位窗口内的比电容达482 F·g-1,优于纯组分MnO2和NiCo2O4的电容性能.     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

Structural and dielectric/ferroelectric properties of (La1−xNdx)2Ti2O7 synthesized by sol-gel route

A series of compounds with the general formula (La_1−xNd_x)₂Ti₂O₇ (0.0≤x≤1.0) has been prepared by the sol-gel method. The decomposition of the gel was characterized by thermo-gravimetric analysis coupled to mass spectrometry, indicating the reaction is achieved above 850 °C. The lattice parameters versus x show an expected decrease in the a and b parameters while c and the β angle remain almost unchanged with respect to the monoclinic symmetry conserved for the full solid solution. Dielectric, piezoelectric and ferroelectric properties were measured on the entire series.     

Reactions of chlorofullerene C60Cl6 with N-substituted piperazines

It was shown for the first time that reactions of C₆₀ halides with aliphatic amines provide a facile route for the synthesis of aminofullerenes, valuable precursors for water-soluble cationic fullerene derivatives. Particularly, chlorofullerene C₆₀Cl₆ and N-substituted piperazines were investigated in this work. It was shown that substitution of chlorine atoms in C₆₀Cl₆ by amine groups is accompanied by partial elimination of addends from the fullerene cage that yields mixtures of di-, tetra- and, hexaaminofullerenes as the final products. Separation of these mixtures by column chromatography resulted in isolation of pure 1,4-diaminofullerenes; this procedure gives much higher and more reproducible yields of these compounds than direct oxidative photoaddition of secondary amines to C₆₀. ESI mass spectrometry and NMR spectroscopy data showed that hexaaminofullerene isomers are major components in inseparable mixtures of polyaddition products. Polyaminofullerenes were found to be readily soluble in aqueous acids; these solutions are unstable because of a facile substitution of protonated amine groups with hydroxyls. Nevertheless, the use of other amine substrates in the investigated reaction can potentially allow the preparation of more stable water-soluble cationic fullerene derivatives for biological studies.     

Fe3O4 Nanoparticles as an Efficient and Magnetically Recoverable Catalyst for the Synthesis of α,β-Unsaturated Heterocyclic and Cyclic Ketones under Solvent-Free Conditions

An efficient and green procedure has been developed for the synthesis of monoarylidenes of cyclic and heterocyclic ketones. The reaction was carried out under solvent-free conditions in the presence of a catalytic amount of nanosized magnetite (Fe₃O₄). The catalyst was easily removed by using an external magnet. The structures of the products were deduced from their ¹H NMR, ¹³C NMR, and infrared spectroscopy and mass spectrometry.

[Supplementary materials are available for this article. Go to the publisher's online edition of Synthetic Communications^® for the following free supplemental resource(s): Full experimental and spectral details.]     

碱熔融-电感耦合等离子体原子发射光谱法测定氧化铟锡烧结混合粉中5种杂质元素

采用氢氧化钠熔融样品,热水浸取后盐酸酸化,建立了碱熔融-电感耦合等离子体原子发射光谱(ICP-AES)法测定氧化铟锡烧结混合粉中Fe、Ca、Mg、Al和Si等元素的分析方法.试验结果表明:称取0.500 0 g试样,加入0.80 g氢氧化钠,在灰化炉中熔融120 min,可将样品完全溶解.基体铟和锡的干扰采用基体匹配法消除,被测元素之间没有光谱干扰.钠盐对硅的测定有一定影响,可在标准溶液中加入一定量氢氧化钠予以消除.对方法进行精密度和加标回收试验,测得结果的相对标准偏差均小于5%,方法加标回收率在90%~105%之间.     

Mass spectrometric study of NF3 plasma etching of silicon

NF₃ plasma etching is used for dry cleaning of reactors after plasma-enhanced chemical vapor deposition of hydrogenated amorphous silicon from SiH₄. The NF₃ plasma chemistry, in a closed isothermal plasma box with silicon coated walls, is analyzed by mass spectrometry of gases. Silicon is etched as SiF₄ by F atoms produced in the NF₃ dissociation into F+NF₂, or 2F+NF. The NF radicals recombine as N₂ +2F whereas the long-lived NF₂ radicals do not react with Si, but recombine as N₂F₄ This is the main limitation (or fluorine conversion into SiF₄. The pressure increase at the end point of etching is attributed to the sudden increase of F atom concentration in the gas phase and the consequent recombination q( F atoms as F₂.     

Thermal and photochemical effects on the structure,morphology, thermal and optical properties of PVA/Ni0.04Zn0.96O and PVA/Fe0.03Zn0.97O nanocomposite films

Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O with average diameter of 23 and 19 nm, respectively, have been synthesized by a modified sol–gel method to be used in the preparation of (100 − x)/x poly(vinyl alcohol)/oxide nanocomposite films, with x = 0, 1, 3 and 5 (in wt.%). A 125 W-Hg vapor lamp with emission above 254 nmwas used to irradiate PVA/Ni_0.04Zn_0.96O and PVA/Fe_0.03Zn_0.97O films. The effect on their structural, thermal, morphological and optical properties was studied by TG, DSC, DRX, AFM, UV–vis and PL spectrophotometry. The Ni_0.04Zn_0.96O addition on PVA films decreases the thermal stability of the polymer in inert and in oxidative atmosphere. In contrast, the Fe_0.03Zn_0.97O presence in the PVA films seems to increase the thermal stability of the polymer. The characteristic peak of the crystalline phase of PVA and wurtzite phase of the zinc oxide were identified through X-ray diffraction in both films. The crystallinity of the PVA film increases with UV irradiation and with the presence of Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O. The roughness of the PVA film was not modified by the addition of the doped oxides; however, it increases after UV irradiation, more significantly in the films containing the oxides. The PVA film exhibits absorption around 280 nm characteristic of π–π^∗ transitions related to carbonyl groups from residuals acetate, while the 95/05 PVA/Ni_0.04Zn_0.96O and 95/05 PVA/Fe_0.03Zn_0.97O nanocomposite films show absorption at the visible region which is characteristics of the band gap reduction of the doped oxides. The photoluminescence of PVA was modified by the presence of the oxides in the film. These nanocomposite films are interesting due to their thermal, mechanical (flexible) properties and low cost of production. In addition they are also able to exhibit peculiar optical properties showing potential to be used in photonic devices, gas sensors and organic solar cell applications.     

Structure of the Cu(Salen) molecule Cuo<Subscript>2</Subscript>N<Subscript>2</Subscript>C<Subscript>16</Subscript>H<Subscript>14</Subscript> according to gas-phase electron diffraction data and quantum chemical calculations

In the framework of synchronous gas-phase electron diffraction and mass spectrometry experiment, the saturated vapor of N,N′-ethylenebis(salicylaldiminate) copper(II) CuO₂N₂C₁₆H₁₄ is studied at a temperature T 574(5) K. It is found that evaporation is congruent and the saturated vapor consists of monomeric molecules. Electron diffraction data are proved to correspond to the geometric model for the CuO₂N₂C₁₆H₁₄ molecule of C ₂ symmetry with an almost planar structure of the CuN₂O₂ coordination fragment and internuclear distances \(r_{h_1 } \)(Cu-O) = 1.917(13) Å and \(r_{h_1 } \)(Cu-N) = 1.931(15) Å. The stuctural parameters obtained are compared to those quantum chemically calculated and molecular parameters in crystals.     

Top-down synthesized TiO2 nanowires as a solid matrix for surface-assisted laser desorption/ionization time-of-flight (SALDI-TOF) mass spectrometry

Top-down synthesized TiO₂ nanowires are presented as an ideal solid matrix to analyze small biomolecules at a m/z of less than 500. The TiO₂ nanowires were synthesized as arrays using a modified hydrothermal process directly on the surface of a Ti plate. Finally, the feasibility of the TiO₂ nanowires in the anatase phase as a solid matrix. The crystal and electronic structures of the top-down TiO₂ nanowires were analyzed at each step of the hydrothermal process, and the optimal TiO₂ nanowires were identified by checking their performance toward the ionization of analytes in surface-assisted laser desorption/ionization time-of-flight (SALDI-TOF) mass spectrometry. Finally, the feasibility of the TiO₂ nanowires in the anatase phase as a solid matrix for SALDI-TOF mass spectrometry was demonstrated using eight types of amino acids and peptides as model analytes.     

Mass spectral analysis and imaging of tissue by ToF-SIMS—The role of buckminsterfullerene, C60, primary ions

Recent developments in desorption/ionisation mass spectrometry techniques have made their application to biological analysis a realistic and successful proposition. Developments in primary ion source technology, mainly through the advent of polyatomic ion beams, have meant that the technique of secondary ion mass spectrometry (SIMS) can now access the depths of information required to allow biological imaging to be a viable option.Here the role of the primary ion C₆₀⁺ is assessed with regard to molecular imaging of lipids and pharmaceuticals within tissue sections. High secondary ion yields and low surface damage accumulation are demonstrated on both model and real biological samples, indicating the high secondary ion efficiency afforded to the analyst by this primary ion when compared to other cluster ion beams used in imaging. The newly developed 40 keV C₆₀⁺ ion source allows the beam to be focused such that high resolution imaging is demonstrated on a tissue sample, and the greater yields allow the molecular signal from the drug raclopride to be imaged within tissue section following in vivo dosing.The localisation shown for this drug alludes to issues regarding the chemical environment affecting the ionisation probability of the molecule; the importance of this effect is demonstrated with model systems and the possibility of using laser post-ionisation as a method for reducing this consequence of bio-sample complexity is demonstrated and discussed.     

浸渍-分解法制备高可见光催化活性的Bi2O3/TiO2纳米管阵列

用浸渍-分解法将Bi₂O₃纳米颗粒沉积在TiO₂纳米管壁上, 制备了Bi₂O₃/TiO₂纳米管阵列. 用电感耦合等离子体发射光谱(ICP-AES)测定了Bi₂O₃/TiO₂ 纳米管阵列的化学组分, 利用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 通过在可见光下(λ>400 nm)降解甲基橙(MO)水溶液来评价样品的光催化活性. 结果表明, Bi₂O₃纳米颗粒均匀地沉积在TiO₂纳米管中. Bi₂O₃/TiO₂纳米管阵列具有比纯Bi₂O₃膜和N-TiO₂纳米管阵列高得多的可见光催化活性. Bi₂O₃/TiO₂纳米管阵列活性的增强是其强可见光吸收和Bi₂O₃与TiO₂之间形成的异质结的协同作用的结果.     

Y2O3 and MgO co-doped ceria based electrolytes

Electrolytes of Ce_1-x-y Y _x Mg _y O_2-0.5x-y were prepared with citrate method and were characterized by inductively coupled plasma-atomic emission spectrometry, energy dispersive spectrometry, powder X-ray diffraction, and impedance spectroscopy. The effect of composition on the structure, conductivity, and stability of the electrolytes were investigated. When 0≤x≤ about 0.2 and 0≤y≤ about 0.05, the electrolytes were all single phase materials of ceria-based solid solution. However, when y> about 0.05, the electrolytes became two-phase materials, Y³⁺ and Mg²⁺ co-doped ceria-based solid solution and free MgO. The sample with nominal composition of Ce_0.815Y_0.065Mg_0.12O_2-d showed ionic conductivity at 973 K close to or even a little higher than that of similarly prepared Ce_0.9Gd_0.1O_1.95, but had lower cost of raw materials and a little better stability in reducing atmosphere. The existing of free MgO improved the stability of the electrolytes in reducing atmosphere, but too much free MgO reduced the conductivity.     

Optical Diagnostics of the Effect of Oxygen on Bi-Level Contact Etch

The effect of oxygen flow rate on bi-level contact etch was studied by observing uv-visible emission from the plasma, during CHF₃/CO/O₂ etching of di-electric layers consisting of SiO₂ and SiN_x. The emission intensity of CN at 387 nm drifted progressively from wafer to wafer during plasma etch. Such a phenomenon became more obvious when using low or high oxygen flow rate, whereas for intermediate flow rates, no significant drift of emission intensity was observed. The critical dimension (CD) bias of each wafer showed a strong correlation with CN emission intensity. Possible mechanisms for such an intensity drift phenomenon are proposed. The drift of emission intensity indicates that the contribution of chamber wall polymers in wafer etching is non-negligible. The CN emission intensity is an indication of the magnitude of etching rate. Our results suggest that the variation of plasma emission intensity might be used as an index for in-line monitoring of CD bias fluctuation.