Trace determination of volatile sulfur compounds by solid-phase microextraction and GC-MS

A method was developed for the simultaneous determination of the following nine volatile sulfur compounds in gas samples: carbon disulfide, carbonyl sulfide, ethyl sulfide, ethyl methyl sulfide, hydrogen sulfide, isopropanethiol, methanethiol, methyl disulfide and methyl sulfide. The target compounds were preconcentrated by solid-phase microextraction (SPME) and determined by gas chromatography combined with mass spectrometry. Experimental design was employed to optimize the extraction time and temperature and concurrent detection of the nine compounds was achieved by using an SPME fiber coated with Carboxen-polydimethylsiloxane (75 microns). Detection limits ranged from 1 ppt (v/v) for carbon disulfide to 350 ppt (v/v) for hydrogen sulfide and calibration functions were linear up to 20 ppb (v/v) for all the compounds investigated.     

Quantitative determination of wine highly volatile sulfur compounds by using automated headspace solid-phase microextraction and gas chromatography-pulsed flame photometric detection. Critical study and optimization of a new procedure

The quantitative determination of wine volatile sulfur compounds by automated headspace solid-phase microextraction (HS-SPME) with a carboxen-polydimethylsiloxane (CAR-PDMS) fiber and subsequent gas chromatography-pulsed flame photometric detection (GC-PFPD) has been evaluated. The direct extraction of the sulfur compounds in 5 ml of wine has been found to suffer from matrix effects and short linear ranges, problems which could not be solved by the use of different internal standards or by multiple headspace SPME. These problems were attributed to saturation of the fiber and to competitive effects between analytes, internal standards and other wine volatiles. Another problem was the oxidation of analytes during the procedure. The reduction in sample volume by a factor 50 (0.1 ml diluted with water or brine) brought about a reduction in the amount of sulfur compounds taken in the fiber by a factor just 3.3. Consequently, a new procedure has been proposed. In a sealed vial containing 4.9 ml of saturated NaCl brine, the air is thoroughly displaced with nitrogen, and the wine (0.1 ml) and the internal standards (0.02 ml) are further introduced with a syringe through the vial septum. This sample is extracted at 35 degrees C for 20 min. This procedure makes a satisfactory determination possible of hydrogen sulfide, methanethiol, ethanethiol, dimethyl sulfide, diethyl sulfide and dimethyl disulfide. The linear dynamic ranges cover the normal ranges of occurrence of these analytes in wine with typical r2 between 0.9823 and 0.9980. Reproducibility in real samples ranges from 10 to 20% and repeatability is better than 10% in most cases. The method accuracy is satisfactory, with errors below 20% for hydrogen sulfide and mostly below 10% for the other compounds. The proposed method has been applied to the analysis of 34 Spanish wines.     

Determination of arsenic in biological fluids by electrothermal atomic absorption spectrometry

A procedure for the determination of the total content of arsenic in urine, serum and blood by electrothermal atomic absorption spectrometry (ETAAS) is described. Zeeman correction is used to compensate the high background signals. The samples are diluted (1 + 1 for urine and 1 + 3 for both serum and blood samples) in a medium containing 0.1% w/v Triton X-100 before being introduced directly into the furnace. A solution containing 15% w/v hydrogen peroxide, 0.65% w/v nitric acid and 0.5% w/v nickel is also introduced into the atomizer by means of a separate injection. Calibration is carried out against aqueous standards for blood and serum samples and using the standard additions method for urine samples. The detection limit is 20 pg (2 ng ml-1). The reliability of the procedure is checked by analyzing three certified reference materials and by recovery studies.     

Determination of Dimethyl Sulfide in Gas Samples by Single Photon Ionization Time of Flight Mass Spectrometry

It is difficult to determine sulfur-containing volatile organic compounds in the atmosphere because of their reactivity. Primary off-line techniques may suffer losses of analytes during the transportation from field to laboratory and sample preparation. In this study, a novel method was developed to directly measure dimethyl sulfide at parts-per-billion concentration levels in the atmosphere using vacuum ultraviolet single photon ionization time-of-flight mass spectrometry. This technique offers continuous sampling at a response rate of one measurement per second, or cumulative measurements over longer time periods. Laboratory prepared samples of different concentrations of dimethyl sulfide in pure nitrogen gas were analyzed at several sampling frequencies. Good precision was achieved using sampling periods of at least 60 seconds with a relative standard deviation of less than 25%. The detection limit for dimethyl sulfide was below the 3 ppb olfactory threshold. These results demonstrate that single photon ionization time-of-flight mass spectrometry is a valuable tool for rapid, real-time measurements of sulfur-containing organic compounds in the air.     

Development of a quantification method for the analysis of malodorous sulphur compounds in gaseous industrial effluents by solid-phase microextraction and gas chromatography-pulsed flame photometric detection

A quantification method for malodorous sulphur compounds in gaseous industrial effluents using solid-phase microextraction sampling followed by gas chromatography-pulsed flame photometric detection has been developed. A comparative study showed that polydimethylsiloxane-Carboxen fibre led to sufficient sensitivity to achieve the microg m(-3) human perception levels of the five analytes studied (hydrogen sulphide, methanethiol, ethanethiol, dimethyl sulphide, dimethyl disulphide). However, this coating is known to suffer from competitive adsorption, which may lead to inaccurate quantification. Therefore, external calibration can only be used under a limited range of concentrations, which were determined from Fick's diffusion law. This approach was tested on a real gaseous sample and compared with the standard addition method. Good correlations were found for ethanethiol, dimethyl sulphide and dimethyl disulphide. However, for more volatile sulphur compounds (i.e., hydrogen sulphide and methanethiol), the easy-to-use external calibration could not be applied and standard additions had to be performed for accurate quantification.     

Stability of sulfonamides,nitrofurans, and chloramphenicol residues in preserved raw milk samples measured by liquid chromatography

A stability study was made of 10 antimicrobials: 6 sulfonamides, 3 nitrofurans, and chloramphenicol residues in raw milk samples preserved with 0.1 % potassium dichromate (K2Cr2O7) and 0.05% mercuric bichloride (HgCl2) during cold storage for 7 days. Preserved milk samples fortified with 50 ppb of each antimicrobial were analyzed by liquid chromatography (modified AOAC Method 993.32). Drugs were extracted with chloroform-acetone after solvent evaporation residues were dissolved with aqueous sodium acetate buffer solution (0.02M, pH 4.8), and fat was removed with hexane. Sulfonamides and chloramphenicol were detected at 275 nm (UV) by using a gradient system of sodium acetate buffer solution-acetonitrile starting at 95 + 5 (v/v) and finishing at 80 + 20 (v/v). Nitrofurans were detected at 375 nm (UV) isocratically with sodium acetate buffer solution-acetonitrile (80 + 20, v/v). Residues stability was measured through recovery data. Sulfamethoxazole, sulfachloropyridazine, nitrofurazone, furazolidone, and furaltadone residues remained stable in the presence of either preservative for 7 days. Sulfamethazine and chloramphenicol were not affected by K2Cr2O7, but had significant losses (p <0.05) when HgCl2 was used: 26.2 and 13.4%, respectively. Average recoveries of sulfamonomethoxine, sulfamerazine, and sulfathiazole significantly decreased by Day 7, with losses of 17.1, 17.2, and 23.2% for K2Cr2O7, and 23.3, 20.7, and 48.0% for HgCl2, respectively. During 5 days of cold storage all antimicrobials tested, except sulfathiazole, remained stable in milk samples preserved with 0.1 % K2Cr2O7 or 0.05% HgCl2.     

The fundamental properties of the direct injection method in the analysis of gaseous reduced sulfur by gas chromatography with a pulsed flame photometric detector

In this study, the fundamental aspects of gas chromatography with a pulsed flame photometric detector were investigated through the calibration of gaseous reduced sulfur compounds based on the direct injection method. Gaseous standards of five reduced sulfur compounds (hydrogen sulfide, methane thiol, dimethyl sulfide, carbon disulfide, and dimethyl disulfide) were calibrated as a function of injection volume and concentration level. The results were evaluated by means of two contrasting calibration approaches: fixed standard concentration method (variable volumetric injection of standard gases prepared at a given concentration) and fixed standard volume method (injection of multiple standards with varying concentrations at a given volume). The optimum detection limit values of reduced sulfur compounds, when estimated at 100 μL of injection volume, ranged from 2.37 pg (carbon disulfide) to 4.89 pg (dimethyl sulfide). Although these detection limit values improved gradually with decreasing injection volume, the minimum detectable concentration (e.g., in nmol mol⁻¹ scale) remained constant due to a balance by the sample volume reduction. The linearity property of pulsed flame photometric detector also appeared to vary dynamically with changes in its sensitivity. According to this study, the performance of pulsed flame photometric detector, when tested by direct injection method, is highly reliable to precisely describe the behavior of reduced sulfur compounds above ∼20 nmol mol⁻¹.     

Determination of flavone C-glucosides in antioxidant of bamboo leaves (AOB) fortified foods by reversed-phase high-performance liquid chromatography with ultraviolet diode array detection

A sensitive solid-phase microextraction and gas chromatography-pulsed flame photometric detection technique was developed to quantify volatile sulfur compounds in wine. Eleven sulfur compounds, including hydrogen sulfide, methanethiol, ethanethiol, dimethyl sulfide, diethyl sulfide, methyl thioacetate, dimethyl disulfide, ethyl thioacetate, diethyl disulfide, dimethyl trisulfide and methionol, can be quantified simultaneously by employing three internal standards. Calibration curves were established in a synthetic wine, and linear correlation coefficients (R2) were greater than 0.99 for all target compounds. The quantification limits for most volatile sulfur compounds were 0.5 ppb or lower, except for methionol which had a detection limit of 60 ppb. The recovery was studied in synthetic wine as well as Pinot noir, Cabernet Sauvignon, Pinot Grigio, and Chardonnay wines. Although the sulfur compounds behaved differently depending on the wine matrix, recoveries of greater than 80% were achieved for all sulfur compounds. This technique was applied to analyze volatile sulfur compounds in several commercial wine samples; methionol concentrations were found at the ppm level, while the concentrations for hydrogen sulfide, methanethiol, and methyl thioacetate were at ppb levels. Only trace amounts of disulfides and trisulfides were detected, and ethanethiol was not detected.     

TG-MS与Py-GC相结合法研究惰性气氛下含硫模型化合物热解过程中硫的脱除及释放行为研究

采用热重-质谱法(TG-MS)和热解-气相色谱法(Py-MS)相结合的方法对模型化合物(十四硫醇、二丁基硫醚、苯硫醚、二甲基噻吩、苯并噻吩和二苯并噻吩等)在惰性气氛下硫的脱除及释放行为进行研究。惰性气氛下硫的脱除顺序为:十四硫醇>二丁基硫醚>二甲基噻吩>苯并噻吩>苯硫醚>二苯并噻吩,苯硫醚除外,该顺序与含硫官能团的热分解顺序一致。在热解过程中,所有模型化合物在质谱和气相色谱仪上均被检测到SO₂;除苯硫醚和二苯并噻吩外,其他模型化合物中均检测到了COS;而只在十四硫醇、二丁基硫醚和二甲基噻吩中检测到了H₂S。且热解气中SO₂含量要显著高于H₂S和COS。这是由于活性炭作载体时,惰性气氛下内部氢的含量显著小于内部氧的含量,所以大多数的含硫自由基易与内部氧结合以SO₂的形式逸出。对于苯硫醚、苯并噻吩和二苯并噻吩中没有检测到H₂S,是由于内部氢的不足,使得含硫自由基不能与内部氢结合,所以没有检测到H₂S逸出。     

Evaluation of preconcentration methods in the analysis of synthetic musks in whole‐water samples

According to the European Water Framework Directive, environmental assessment of organic compounds should be made in whole‐water samples, but due to their hydrophobicity and strong attraction to organic content these compounds can be found bound to suspended particle matter or in the dissolved fraction. In this work, the extraction of musk compounds was studied in whole‐water samples exhibiting different amounts of dissolved organic carbon and suspended particulate matter using polyethersulfone preconcentration technique. Matrix effects in estuarine and wastewater (both influent and effluent) were evaluated for filtered and unfiltered samples. For unfiltered samples, estuarine water exhibited matrix effects <20%, while for effluent it was up to 48% and for influent ranged from 85 to 99%. To compensate matrix effects and determine total concentrations in unfiltered samples, different quantification approaches were tested: the use of deuterated analogues and standard additions. Standard additions provided the best results for unfiltered samples. Finally, filtered and unfiltered samples were analyzed using both polyethersulfone preconcentration and membrane‐assisted solvent extraction and results showed a good agreement between the two methods. In both cases unfiltered samples provided concentrations 1.5–2.6 times higher than filtered samples.     

Volatilization losses of mercury in neutron activation analysis

The volatilization losses of mercury before, during and after neutron irradiation were studied. To minimize the losses, respectively, were added to the standards, thiourea, L-cysteine, thioacetamide and ammonium sulfide. It was possible to minimize the losses by preserving the standard at −20°C after irradiation. No loss was seen in the biological materials after irradiation.     

Mapping of protein:protein contact surfaces by hydrogen/deuterium exchange,followed by on-line high-performance liquid chromatography-electrospray ionization Fourier-transform ion-cyclotron-resonance mass analysis

Furfural contents in adapted and follow-up infant formulas were measured by RP-HPLC. The evolution of furfural compound contents during storage (a year at 20 and 37 degrees C) was studied. 2-Furylmethylketone and 5-methyl-2-furaldehyde were not detectable in analysed samples. The differences in the furfural compounds at point zero between both infant formulas has to be ascribed to the differences in protein and iron contents. An increase in free 5-hydroxymethyl-2-furfuraldehyde (HMF), 2-furaldehyde (F) and HMF+F contents was observed in all samples, although the differences were not statistically significant. The storage temperature affected the total HMF content and the storage time affected the total HMF and F contents.     

Organotin stability during storage of marine waters and sediments

Summary The stability of organotin compounds in water and sediment samples during storage and pre-treatment is of paramount importance. This study presents experiments with butyltin compounds showing that the storage of filtered natural seawater in the dark at pH 2 in pyrex glass bottles is suitable to preserve the stability of tributyltin (TBT) over 4 months both at 20–25°C and 4°C. The other butyltin compounds (mono- and dibutyltin) are stable at 4°C but display some losses at 25°C. A poor recovery of butyltins in turbid water hampered the assessment of the stability on a quantitative basis: however, it could be demonstrated on a qualitative basis that the butyltin stability is uneasily achieved in water samples with high suspended matter. Finally, wet storage and freezing are found to be suitable to preserve the tributyltin stability in sediments, as well as ovendrying (at 50°C), freeze-drying and air-drying. Mono- and dibutyltin are generally subject to changes during the storage of sediments using the different methods.     

Dynamic system for the calibration of semi-volatile carbonyl compounds in air

A dynamic calibration system designed for generating accurate and precise concentrations of semi-volatile carbonyls in the ppb (v/v) (ppbv)-ppt (v/v) (pptv) range has been developed and tested. Alkanals from C6 to C9 were used as test compounds. Diffusion rates of their vapours from capillary tubes were determined theoretically and with two methods whose accuracy was independently evaluated with liquid standard solutions. Methods selected for testing the calibration system were those commonly used for the selective quantification of carbonyls in air. One is based on the well-known reaction with 2,4-dinitrophenylhydrazine (DNPH), followed by the analysis of formed hydrazones by HPLC-UV. The other is based on the retention of carbonyls on graphitic carbon adsorbents, followed by MS detection of the sample injected into a capillary column by thermal desorption. A good consistency was found between the values of the diffusion rates determined by the two methods. The scatter between the two methods was in the range of +/-10% when diffusion rates of ca. 1 ng/s were attained. Experimental values closely approached those calculated by applying the equation describing the diffusion of a vapour in equilibrium with the liquid through a capillary tube.     

Determination of ultra-micro amounts of sulfur in igneous rocks by spectrofluorimetry using 2-(o-hydroxyphenyl) benzoxazole derivatization and tin(II)-strong phosphoric acid-assisted reduction

A new and very sensitive method was developed for the determination of ultra-micro amounts of sulfur in igneous rock samples. The sulfur compounds in an igneous rock sample are reduced and released in the form of hydrogen sulfide by heating with a tin(II)-strong phosphoric acid (SPA) reagent. The liberated hydrogen sulfide is carried by a flow of nitrogen into a copper(II) absorbing solution to obtain a precipitate of copper(II) sulfide. The remaining copper(II) ion forms a chelate with 2-(o-hydroxyphenyl)benzoxazole (HPB) and quenches the fluorescence of HPB. The amount of sulfide is determined by measuring the HPB fluorescence intensity. The optimum reaction conditions were stoichiometrically investigated. By the present method using 0.1-0.2 g of rock sample, ultramicro amounts of sulfur (0.1-12.8 mug) could be quantitatively separated, collected, and determined with a relative standard deviation of 1.37% for a sample containing 5.7 mug of sulfur (95% confidence level).     

An improved method for the analysis of volatile polyfluorinated alkyl substances in environmental air samples

This article describes the optimisation and validation of an analytical method for the determination of volatile polyfluorinated alkyl substances (PFAS) in environmental air samples. Airborne fluorinated telomer alcohols (FTOHs) as well as fluorinated sulfonamides and sulfonamidoethanols (FOSAs/FOSEs) were enriched on glass-fibre filters (GFFs), polyurethane foams (PUFs) and XAD-2 resin by means of high-volume air samplers. Sensitive and selective determination was performed using gas chromatography/chemical ionisation–mass spectrometry (GC/CI–MS). Five mass-labelled internal standard (IS) compounds were applied to ensure the accuracy of the analytical results. No major blank problems were encountered. Recovery experiments were performed, showing losses of the most volatile compounds during extraction and extract concentration as well as strong signal enhancement for FOSEs due to matrix effects. Breakthrough experiments revealed losses of the most volatile FTOHs during sampling, while FOSAs/FOSEs were quantitatively retained. Both analyte losses and matrix effects could be remediated by application of adequate mass-labelled IS. Method quantification limits (MQLs) of the optimised method ranged from 0.2 to 2.5 pg/m³ for individual target compounds. As part of the method validation, an interlaboratory comparison of instrumental quantification methods was conducted. The applicability of the method was demonstrated by means of environmental air samples from an urban and a rural location in Northern Germany. Figure High-volume air sampling of volatile polyfluorinated alkyl substances using glass fibre filters and PUF/XAD-2 cartridges at a background monitoring site (Waldhof, Germany)     

Investigation of the storage stability of selected volatile sulfur compounds in different sampling containers

The suitability of various sample containers (i.e. standard Tedlar sample bags, black/clear layered Tedlar sample bags and Silcosteel sample cylinders) was examined for a gaseous multicomponent standard containing methylmercaptan, ethylmercaptan, dimethyl sulfide, ethylmethyl sulfide, 2-propylmercaptan, 1-propylmercaptan, 2-butylmercaptan, diethyl sulfide and 1-butylmercaptan (1 mg/m3 each in nitrogen). In the black/clear layered Tedlar sample bags, significant losses (up to 10% for methylmercaptan as the most critical component) were observed after 2 days, whereas in the standard Tedlar sample bags the recovery of methylmercaptan was approximately 90% even after 1 week. The Silcosteel sample cylinders were suitable for sampling of volatile sulfur compounds with respect to the stability of the analytes, but the recoveries exceeded 100% especially for the higher boiling compounds, which was attributed to enrichment effects on parts of the sampling system.     

Multiresidue determination of pesticides in acid-clay soils from Thailand

Tropical and temperate soils differ with respect to their chemical conditions and mineral composition. Consequently, assessment of the contamination of tropical soils with pesticides requires methods that provide exhaustive extraction from the specific soil matrix and reliable quantification. Our objective was to optimize the simultaneous extraction and determination of 32 representative pesticides (organophosphates, organochlorines, synthetic pyrethroids, triazines, acetamides, carbamates, diphenyl ethers, acylalanines, oxadiazoles, thiadiazoles, and phenoxy compounds) frequently used in Thailand. The compounds were added to a clayey Ultisol-topsoil (45% clay) from the Yom Region in Northern Thailand. Ten different solvent mixtures were tested; the use of a shake extraction with acetone-ethyl acetate-water (3 + 1 + 1, v/v/v) was most effective in providing exhaustive and reproducible extraction of pesticides both from freshly fortified soil and from fortified soil after incubation for 14-28 days. The pesticides were separated and quantified by using gas chromatography with mass selective detection. Except for methamidophos, which was almost completely lost during sample workup, the recoveries of all pesticides from soil ranged from 68.6 to 104% (mean standard error, 2.8%) for freshly spiked samples and from 45.9 to 107% (mean standard error, 2.3%) for spiked samples incubated for 14 days. The use of internal standards compensated for the losses of most pesticides during workup and increased the mean recovery of the pesticides from freshly fortified soil to 96%. The method was successfully applied to the determination of environmental concentrations of pesticides in a range of Thai agricultural soils.     

Sample preparation and determination of ginkgo terpene trilactones in selected beverage, snack, and dietary supplement products by liquid chromatography with evaporative light-scattering detection

Ginkgo biloba leaf extract has been widely used in dietary supplements and more recently in some foods and beverages. Sample preparation procedures for determination of ginkgo terpene trilactones (including bilobalide and ginkgolides A, B, C, and J) in various sample matrixes were developed in this study. Ginkgo leaves and capsules were extracted with 5% KH2PO4 aqueous solution under sonication. Tea bags were extracted with boiling water, whereas drink samples were taken directly from the bottles. After filtration and the addition of NaCl to approximately 30% (w/v), the terpene trilactones in aqueous solutions were quantitatively extracted with ethyl acetate-tetrahydrofuran (4 + 1, v/v). Puff samples (a cereal-based fried snack item) were first defatted by using hexane or by using supercritical fluid extraction and then extracting under sonication with methanol-acetic acid (99 + 1, v/v). After evaporation of the organic phase, the terpene trilactones were redissolved in methanol and determined on a C18 reversed-phase column by liquid chromatography (LC) with evaporative light-scattering detection. The method of standard additions and gas chromatography with flame ionization detection were used for method validation. For most samples, the relative standard deviation was <10%. The identities of target compounds in ginkgo leaves and drink samples were confirmed by LC/electrospray ionization-tandem mass spectrometry.     

Addition of internal standards to particulate sample matrices for routine trace analyses of semivolatile organic compounds: A source of systematical and random errors

This article is a criticism of the strategy of adding (isotope labelled) internal standards of semi volatile hydrophobic organic compounds directly on the surface of particulate samples matrix such as sediment, soil and fly ash, etc. in a small aliquot (mL) of solvent, before trace level analysis. The use of the internal standard is intended to compensate for incomplete extractions, clean-up losses, dilution errors and instrument variations. However, direct addition of internal standards to sample matrices creates two possibilities for inaccurate results by processes only affecting the internal standard: First, evaporation losses of standard from the sample matrix during evaporation of the carrier solvent. Second, the native analyte and internal standard sorb to the sample matrix with differing force. Both processes can introduce systematic and random error to the result. A systematic error of 74% due to evaporation losses of tetra chlorinated dibenzo-p-dioxins is observed, while the corresponding error for octa chlorinated dioxin is 0%. The associated random error is 45% for tetra down to 1–4% relative standard deviations for hepta and octa chlorinated dioxins. For laboratory staff the evaporation losses of standard (and native) compounds causes, besides dust, an additional risk of inhalation exposure. The internal standard should instead be added to the extraction solvent after the extraction. Smaller systematical errors (10–20%) and associated random errors due to irreversible sorption are discussed.