ICP–AES法同时检测生蚝中铅、铜、镉、铬、铁含量时3种样品前处理方法比较

采用干法、湿法和微波消解法处理珠海生蚝样品,用电感耦合等离子体发射光谱仪在谱线Pb 220.3 nm,Cu 324.7 nm,Cd 228.8 nm,Cr 283.5 nm,Fe 259.9 nm下测定样品中铅、铜、镉、铬、铁5种重金属元素的含量。结果表明,珠海市4个养殖基地的生蚝重金属含量均在国标限量范围内。铅、铜、镉、铬、铁各元素线性相关系数分别为0.999 8,0.999 4,0.999 9,0.999 2,0.997 8,检出限分别为0.020,0.014,0.001,0.036,0.120 mg/kg。干法、湿法、微波消解法的加标回收率分别为72.8%~99.3%,88.0%~102.0%,89.0%~103.0%。微波消解处理样品,ICP–AES法同时测定4种样品中5种重金属的含量,其测定结果的相对标准偏差均小于17%。微波消解–ICP–AES适合生蚝中铅、铜、镉、铬、铁含量的快速测定。     

电感耦合等离子体质谱法测定有机肥料中砷、镉、铅、铬、汞的含量

提出了用微波消解-电感耦合等离子体质谱法测定有机肥料中砷、镉、铅、铬、汞等5种元素的方法。有机肥料样品(0.200 0~0.500 0g)加入硝酸10mL和过氧化氢溶液1mL,按程序升温微波消解,将消解液蒸发至2mL,用硝酸(1+99)溶液定容至50mL。用电感耦合等离子体质谱法测定上述样液中的砷、镉、铅、铬、汞等元素。各元素的检出限(3.3s/k)为0.015~0.040mg·kg~(-1),测定值的相对标准偏差(n=6)均小于5.0%。按标准加入法进行回收试验,测得回收率在98.0%~101%之间。     

ICP-OES法同时测定功效牙膏中10种元素

采用ICP-OES同时测定功效牙膏中的铅、镉、汞、砷、铜、锌、钾、锶、银、钛等10种元素。结果表明,在HNO3-H2O2-HF体系下,采用微波消解方法,对牙膏样品进行完全消解。通过优化仪器条件参数,实现对功效牙膏中的铅、镉、汞、砷、铜、锌、钾、锶、银、钛等元素的ICP-OES法同时测定。钛、钾元素质量浓度在5.0~100.0 mg/L,锶、锌元素质量浓度在1.0~50.0 mg/L,铅、镉、汞、砷、铜、银元素质量浓度在0.1~2.0 mg/L范围内时,方法有良好的线性关系,相关系数均大于0.992。样品中各元素的加标回收率在93.0%~109.0%。     

布洛芬注射液包材相容性研究中铅、镉、砷、锑的测定

建立中性硼硅玻璃包材加速试验后布洛芬注射液中铅、镉、砷、锑含量的检测方法。采用微波消解仪以硝酸分解样品,用石墨炉原子吸收光谱仪测定铅、镉含量,测定波长铅为283.3 nm,镉为228.8 nm,铅、镉分别在5.0~50.0,0.5~5.0μg/L范围内有良好的线性,相关系数分别为0.999 7,0.996 2,检出限分别为0.26,0.01μg/L,测定结果的相对标准偏差分别为1.06%,2.40%(n=6),加标回收率分别为100.2%~101.9%,97.1%~105.1%。用原子荧光光谱仪测定砷、锑含量,测定波长砷为193.7 nm,锑为217.6 nm,砷、锑在1~10μg/L范围内均有良好的线性,相关系数分别为0.999 9,0.999 5,检出限分别为0.03,0.01μg/L,测定结果的相对标准偏差分别为1.04%,2.65%(n=6),加标回收率分别为94.2%~96.5%,92.6%~96.5%。该测定方法快速,灵敏度高,适用于内包装材料加速试验后药品中重金属元素含量变化的研究。     

微波消解–ICP–OES法测定陶土中铅和镉含量

建立微波消解–ICP–OES法测定陶土中铅和镉含量的方法。采用氢氟酸–硝酸作为消解液,微波消解法处理样品,消解液定容后直接进入耐氢氟酸的进样系统,用ICP–OES法测定陶土中重金属铅和镉的含量。结果表明,Pb和Cd检出限分别为0.027μg/m L和0.011μg/m L,回收率分别为90.5%~98.8%和95.0%~98.4%,测定结果相对标准偏差分别为1.38%和2.17%(n=7)。该方法具有快速、准确、灵敏度高等优点,适用于陶土中铅和镉含量的检测。     

微波消解-电感耦合等离子体质谱法测定砂仁中的铜、铅、砷、镉

建立了微波消解样品,电感耦合等离子体质谱法(ICP–MS)测定黔西南高砷土壤种植的砂仁中痕量铜、铅、砷、镉的分析方法。对微波消解条件进行了优化。为了避免消解试剂对质谱测定的干扰,选择硝酸–双氧水混合溶液(体积比为3∶1)作为微波消解试剂,采用ICP–MS测定消解液中铜、铅、砷、镉的含量。利用校正方程对砷、镉的质谱干扰进行校正。铜、铅、砷、镉4种元素的线性相关系数均大于0.999 2,检出限分别为0.073,0.048,0.39,0.062μg/L,测定结果的相对标准偏差小于4.5%(n=5)。各元素的加标回收率在96.0%～105.0%之间。该方法样品处理快速、简单,溶解率高,测定结果准确、可靠,适用于成批量砂仁样品中铜、铅、砷、镉微量元素的测定。     

微波消解–电感耦合等离子体质谱法测定酱卤肉中铬、砷、镉、铊、铅

建立微波消解–电感耦合等离子体质谱法测定酱卤肉中铬、砷、镉、铊、铅5种元素含量的检测方法。采用微波消解法处理酱卤肉样品,对预处理条件和仪器工作参数进行了优化,以内标校正法降低基体影响。结果表明,铬、砷、镉、铊、铅5种元素的质量浓度在0.1~50.0 μg/L范围内与质谱响应值具有良好的线性关系,相关系数均大于0.999,方法检出限为0.2~6.2 μg/kg。在3种加标浓度水平下平均回收率为72.4%~113.5%,测定结果的相对标准偏差为3.1%~7.7%(n=6)。该方法简便,快速,高效,准确,可为酱卤肉中铬、砷、镉、铊、铅的测定提供技术支持。     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

微波消解-原子吸收光谱法测定粮谷中铅、铜、镉、镁、锰、铁

用微波消解法进行样品消解,原子吸收光谱法测定了小麦粉国家标准物质中铅、铜、镉、镁、锰、铁6种元素的含量.其中镁、锰、铁用火焰原子化法,铅、铜、镉用石墨炉原子化法,方法的相对标准偏差分别为1.43%(镁),4.72%(镉),5.20%(锰),6.04%(铜),13.8%(铁)及18.7%(铅),检出限分别为0.001(铅及铜),0.000 1(镉),0.01(锰)及O.02(镁和CA)mg·kg-1.     

ICP–MS法测定食品接触纸制品中铬、镍、砷、镉、铅、汞

建立电感耦合等离子体质谱法(ICP–MS)测定食品接触纸制品中铬、镍、砷、镉、铅、汞6种重金属含量的方法。样品经微波消解处理后用ICP–MS进行测定,内标法定量。在优化实验条件下,测定汞元素的线性范围在0~10μg/L之间,测定铅、镉、铬、镍、砷元素的线性范围在0~100μg/L之间,相关系数均大于0.999。各元素的检出限为0.001~0.1 mg/kg,加标回收率为89.3%~116.0%,测定结果的相对标准偏差为3.5%~7.9%(n=6)。该方法样品处理简单,检测灵敏度高,适用于食品接触纸制品中铬、镍、砷、镉、铅、汞的检测。     

Direct determination of Cd, Cu and Pb in wines and grape juices by thermospray flame furnace atomic absorption spectrometry

The applicability of thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) was evaluated for direct determination of Cu, Cd and Pb in wines and grape juices. The developed procedure does not require preliminary acid digestion of the samples. The optimum conditions for determination of Cu, Cd and Pb in wines were studied and the performance was compared to those typically obtained by flame atomic absorption spectrometry (FAAS). A sample volume of 150 microL was introduced into a heated nickel tube at a flow rate of 0.54 mLmin(-1) and 0.14 molL(-1) HNO(3) was used as sample carrier flowing at 2.5 mLmin(-1) for determining all analytes. The effect of ethanol concentrations on Cu, Cd and Pb absorbance signals were studied. All determinations were carried out by adopting optimized conditions and quantification was based on the standard additions method. Limits of detection (LOD) of 12.9, 1.8 and 5.3 microgL(-1) (n=14) for Cu, Cd and Pb, respectively, were obtained for wine samples (3sigma(blank)/slope, n=14). Relative standard deviations (R.S.D., %) of 2.7, 2.1 and 2.6 for Cu, Cd and Pb, were obtained (n=6) for wine samples. The values determined for grape juice samples were similar to these ones. The analytical throughput was 45 determinations h(-1) and accuracy was checked by addition-recovery experiments.     

Comparison of open microwave digestion and digestion by conventional heating for the determination of Cd, Cr, Cu and Pb in algae using transverse heated electrothermal atomic absorption spectrometry

A comparison between open microwave digestion and digestion by conventional heating was carried out for the determination of Cd, Cr, Cu, and Pb in two algae matrices using transverse heated electrothermal atomic absorption spectrometry (ETAAS). A SRM GBW 08504 cabbage was also analysed. These matrices were digested with HNO3, using a quartz vessel for microwave digestion and PFA vessel for digestion by conventional heating. Cd, Cu and Cr were determined without any modifier, while magnesium nitrate and ammonium phosphate mixed modifier was used for Pb. Results obtained by both the procedures were in good agreement with each other at 95% confidence level, and for SRM GBW 08504 cabbage the values agree well with the certified values. The limits of detection obtained were 0.0004, 0.060, 0.065 and 0.054 mg/kg for Cd, Cr, Cu, and Pb, respectively, using the microwave digestion process. The RSD for Cd was 10-15% and for the other elements 5-10%.     

微波消解-ICP-MS法同时测定木薯淀粉中铅、铜、镉、砷、汞的含量

用硝酸-过氧化氢溶液(3+3)作为消解剂,微波消解法处理木薯淀粉等样品,采用电感耦合等离子体质谱法,选择适合的同位素元素,运用碰撞池技术(CCT)降低元素Cu、As的多原子离子干扰,测定样品溶液中Pb、Cu、Cd、As、Hg等元素的含量,各元素线性相关系数为0.9997 ～0.9999,元素的检出限(3sd)分别为pb...     

Several modified piezoelectric quartz crystals for determination of omethoate

A chromatographic method for the determination of transition metals in human hair samples is described. The method involves the separation of Cu, Pb, Zn, Ni, Co, Cd and Mn in a C18 column coated with sodium hexadecane-sulfonate (SHS) and spectrophotometric detection (520 nm) after post-column reaction of the eluted metals with 4-(2-pyridylazo)-resorcinol (PAR). The eluent was a 100 mM tartrate solution adjusted to pH 3.1 with a 2 M sodium hydroxide solution (flow-rate=1.0 ml min(-1)). A good separation of the eluted metals (specially for Cu/Pb and Zn/Ni) has been achieved. The detection limits, expressed as mug l(-1), were 2.2 (Cu), 8.0 (Pb), 2.8 (Zn), 1.5 (Ni), 1.5 (Co), 12.0 (Cd), and 1.4 (Mn). A microwave-assisted closed vessel acid digestion procedure with HNO(3)+HClO(4) (4+1 ml) was used for the hair samples solubilisation. Nineteen hair samples were analysed with the proposed method. The results were in good agreement with those obtained by atomic absorption spectrometry (AAS).     

Assessment of Heavy Metal Pollution and Ecological Risk of Roadside Soils in Tlemcen (Algeria) Using Flame-Atomic Absorption Spectrometry

In Algeria, few studies have been conducted on the evaluation of roadside soil pollution. A total of 34 soil samples (28 roadside and 6 off-road) was obtained at 0–20?cm depth along the RN 35 national road. Heavy metal (Cd, Cr, Cu, Fe, Ni, Pb, and Zn) contents were extracted using aqua regia digestion and determined using atomic absorption spectrometry. Background values of heavy metal contents were determined using the robust statistical method of median plus two times the median absolute deviation. Single- and multi-element pollution and ecological risk indices were calculated. The results showed that background values were 2.5?±?0.3, 64.9?±?8.1, 28.0?±?4.1, 29371.5?±?4403.0, 32.9?±?4.4, 72.2?±?12.8, and 445.1?±?62.9?mg/kg for Cd, Cr, Cu, Fe, Ni, Pb, and Zn, respectively. The results were all higher than their corresponding median values. Single-element pollution indices (enrichment factor and geoaccumulation index) showed that the pollution is primarily due to Pb and Zn. Multi-element pollution index (Nemerow index) indicated that only 3% of the soil samples are strongly contaminated, whereas 23% are seriously contaminated. The potential ecological risk index showed that Cd is the most harmful element, followed by Pb and Zn. 65% of the soil samples had moderate potential ecological risk, while only 3% had considerable potential ecological risk. This study may be used as a baseline for future monitoring and as a tool for decision-making regarding environmental protection policies and sustainability of this semiarid agroecosystem.     

Sol-gel zirconia coating capillary microextraction on-line hyphenated with inductively coupled plasma mass spectrometry for the determination of Cr, Cu, Cd and Pb in biological samples

A sol-gel zirconia coating was developed for the preconcentration/separation of trace Cr, Cu, Cd and Pb by capillary microextraction, and the adsorbed analytes were on-line eluted for detection using inductively coupled plasma mass spectrometry (ICP-MS). By immobilizing sol-gel zirconia on the inner surface of a fused-silica capillary, the sol-gel zirconia coating was simply prepared. Its adsorption properties, stability and the factors affecting the adsorption behaviors of Cr, Cu, Cd and Pb were investigated in detail. In the pH range from 7.8 to 10, the zirconia-coated capillary (35 cm x 0.15 mm) is selective towards Cr, Cu, Cd and Pb, and the analyzed ions could be desorbed quantitatively with 0.2 mL of 0.5 mol/L HNO(3) at a rate of 0.2 mL/min. With a consumption of 1.25 mL sample solution, an enrichment factor of 6.25, and detection limits (3sigma) of 9.9 pg/mL Cr, 17.9 pg/mL Cu, 4.5 pg/mL Cd and 3.7 pg/mL Pb were obtained. The precisions for nine replicate measurements of 1 ng/mL Cr, Cu, Cd and Pb were 4.9% Cr, 2.2% Cu, 2.0% Cd and 3.2% Pb (RSD), respectively. The proposed procedure has been applied to the determination of Cr, Cu, Cd and Pb in human urine, which was subjected to microwave-assisted digestion prior to analysis, and the recoveries for these elements were 89.2-101.8%. In order to validate the developed procedure, a NIES No.10-a Rice Flour-Unpolished certified reference material and a BCR No. 184 Bovine Muscle certified reference material were analyzed, and the results are in good agreement with the certified values.     

Determination of Ba, Cd, Cu, Pb and Zn in saliva by isotope dilution direct injection inductively coupled plasma mass spectrometry

Trace elements in small sample volumes of saliva were determined by coupling a high efficiency direct injection nebulizer to inductively coupled plasma mass spectrometry and employing quantification by isotope dilution. Aliquots of 0.4 ml of human saliva were mixed with 0.1 ml of concentrated nitric acid and diluted to 2 ml with water. Sample solutions were spiked with an isotopic solution enriched in 135Ba, 112Cd, 65Cu, 206Pb and 66Zn. The amount of each isotope added to the samples and the measurement procedure were adjusted to attain precise analytical results calculated from the isotope ratios 135Ba/138Ba, 112Cd/114Cd, 65Cu/63Cu, 206Pb/208Pb and 66Zn/68Zn. Data acquisition for Ba, Cu and Zn isotopes was performed for a single sample injection of 50 microl and in another sample injection the Cd and Pb isotopes were measured. Concentrations ranging from 5.0 to 16 microg l(-1) for Ba, from 0.50 to 1.1 microg l(-1) for Cd, from 6.0 to 50 microg l(-1) for Cu, from 0.8 to 18.8 microg l(-1) for Pb and from 46.0 to 230 microg l(-1) for Zn were found in saliva samples. Detection limits of 0.11, 0.03, 0.40, 0.05 and 0.59 microg l(-1) were determined for Ba, Cd, Cu, Pb and Zn, respectively. The concentrations found by isotope dilution were in agreement with those of the completely digested samples quantified by external calibration. The direct analysis of 30 samples per hour was attained with the proposed procedure, avoiding time-consuming digestion steps, contamination risks and matrix effects.     

On-line Preconcentration and Determination of Trace Metals in Water Samples by Flow Injection Combined with Flame Atomic Absorption Spectrometry via Calix[4]arene Carboxylic Acid Packed Micro-column

An adsorbent calix[4]arene carboxylic acid was employed as the adsorption material for on-line flow injection( FI) micro-column preconcentration coupled with flame atomic absorption spectrometry(FAAS) determination of trace heavy metals(Cu, Pb, Co, Ni and Cd). Parameters such as the pH, loading time and flow rate of sample, and the concentration, volume and flow rate of eluent were optimized. The enrichment factors are 50.0, 56.5, 11.6, 12.1 and 19.1 for Cu, Pb, Co, Ni, and Cd, respectively, and a sample throughput of 20 h^-1 was obtained. The limits of detection for Cu, Pb, Co, Ni, and Cd were in a range of 1.56―3.91 μg/L, and the relative standard deviations(RSDs) were less than 2.76%(n=7). Furthermore, the proposed method was successfully applied to the determination of Cu, Pb, Co, Ni, and Cd in certified reference materials and various water samples.     

ICP-MS法同时测定烟草中17种微量元素

采用微波消解前处理样品、电感耦合等离子体质谱检测的方法,同时测定了烟叶中铍(Be)、钛(Ti)、钒(V)、铬(Cr)、镍(Ni)、铜(Cu)、砷(As)、锶(Sr)、钼(Mo)、银(Ag)、镉(Cd)、铯(Cs)、钡(Ba)、铊(Tl)、铅(Pb)、钍(Th)和铀(U)共17种元素,回收率90·27%~110·4%,检出限0·3521~345·3ng/L,相对标准偏差1·65%~9·86%。实验结果表明,该方法能满足痕量分析的要求。用此方法对来自5个地区的烟叶样品进行了考察,研究了以上元素随产地、部位不同的分布特性,发现同一品种不同地区、部位的烟叶中上述元素的含量存在一定的差别。