SAPO-34分子筛催化丁烯转化制丙烯的研究

通过水热法合成SAPO-34分子筛,将其制成催化剂用于催化丁烯转化制取丙烯,考察了反应温度、空速和铝磷比等对催化性能的影响;还比较了SAPO-34分子筛与ZSM-5分子筛催化该反应的差异.结果表明,在实验范围内,反应温度升高会使得丁烯的转化率明显增高,且丙烯选择性提高;而空速增加,则丁烯的转化率和丙烯选择性降低;铝磷比越大,对丙烯的选择性越差.在有效的反应时间内,SAPO-34分子筛催化效果好于ZSM-5分子筛,但单程寿命较ZSM-5分子筛短.     

MCM-49分子筛催化剂上1-丁烯的骨架异构化反应

 采用动态和静态水热合成法合成了不同Si/Al比的MCM-49分子筛,并考察了合成分子筛对1-丁烯骨架异构化反应的催化性能. 结果表明,除目的产物异丁烯外,主要副产物为丙烯和戊烯,产物中没有检测到C6以上的副产物. 异丁烯收率随着反应温度的升高、分子筛晶粒的增大和1-丁烯分压的降低而升高. NH3-TPD 结果表明,随着分子筛Si/Al比的增加,分子筛的酸中心数减少,导致副产物选择性下降,异丁烯选择性升高. 根据反应结果讨论了异丁烯及副产物形成的机理.     

乙烯在ZSM-5催化剂上低聚反应规律的研究

在固定床微反装置上,采用ZSM-5分子筛催化剂,考察了不同条件下乙烯的低聚反应。结果表明,适宜的条件可以抑制副反应,提高产物中丙烯与丁烯的选择性。随反应时间的延长,催化剂因积炭而失活,乙烯转化率由初始的96.2%降至6h后的41.1%,丙烯和丁烯选择性增加。提高乙烯空速可有效抑制氢转移反应从而提高烯烃选择性,根据不同转化率对应的产物分布,得到了ZSM 5催化剂上乙烯低聚的反应路径。乙烯转化率随反应温度的升高先增加后降低,500℃时达到最大值为88.0%,主要产物LPG组分中烷烃居多。提高反应压力有利于低聚反应进行,可以显著提高乙烯转化率,但不利于生成丙烯和丁烯。     

SAPO-34催化剂上反应条件对乙烯转化制丙烯的影响

系统研究了反应条件对SAPO-34上乙烯转化制丙烯的影响.结果表明,提高空速或加大He/C2H4稀释比有利于抑制丙烯二次反应的发生,提高丙烯的选择性.升高温度导致乙烯转化率下降,甲烷和乙烷的选择性增加;在相同转化率下,丙烯选择性随温度上升而下降.乙烯在SAPO-34上的转化反应表现出明显的诱导期,且反应条件对诱导期的长短有较大影响.     

分了筛催化合成MTBE的反应性能研究

在开发出催化性能良好的合成ＭＴＢＥ沸石分子筛催化的基础上,详细考察了反应条件：包括温度、压力、空速、醇烯比等操作条件对改性β沸石分子筛催化剂的合成ＭＴＢＥ反应性能的影响。结果表明：反应条件对催化剂活性、ＭＴＢＥ选择性及活性稳定性都有一定影响。在一定范围内反应温度升高,烯烃的转化率增加、ＭＴＢＥ的选择性不变,但反应温度过高,ＭＴＢＥ的选择性和催化剂的稳定性变差;反应压力必须大于系统完全液化压力;醇烯     

分子筛催化合成MTBE的反应性能研究

在开发出催化性能良好的合成MTBE沸石分子筛催化剂的基础上 ,详细考察了反应条件 :包括温度、压力、空速、醇烯比等操作条件对改性 β沸石分子筛催化剂合成MTBE反应性能的影响。结果表明 :反应条件对催化剂活性、MTBE选择性及活性稳定性都有一定影响。在一定范围内反应温度升高 ,烯烃的转化率增加、MTBE的选择性不变 ,但反应温度过高 ,MTBE的选择性和催化剂的稳定性变差 ;反应压力必须大于系统完全液化压力 ;醇烯比大于 1时 ,对选择性和稳定性的影响程度小 ,醇烯比小于 1时 ,随反应深度增加 ,MTBE选择性和催化剂的稳定性变差。为了充分利用催化剂的性能 ,有一个比较合适的操作范围 ,在最佳反应条件T =70℃、P =2 1MPa ,MeOH IB =1 1 ,WHSV =4h- 1下 ,对改性 β分子筛的催化性能进行长期考察 ,结果表明 :催化剂的各项性能的稳定性很好。     

环己烯水合制备环己醇的研究Ⅰ. 分子筛结构及晶粒大小的影响

考察了三种不同结构的分子筛(ZSM-5,MCM-22及β)以及不同晶粒大小的ZSM-5分子筛对环己烯水合反应的催化活性. 结果表明,具有12元环孔道体系的β分子筛对环己烯的转化率(9.6%)最高,但对环己醇的选择性(35.4%)最差. MCM-22分子筛的活性很低,其环己烯转化率只有0.8%. 而孔口为10元环结构的ZSM-5分子筛则具有较高的活性(环己烯转化率7.5%)和产物选择性(99.2%),因此是较好的水合催化剂. ZSM-5分子筛的晶粒大小对其环己烯水合反应活性有明显的影响,分子筛晶粒越细,则水合反应活性越高,其原因在于晶粒变细增大了分子筛的外比表面积,从而增加了接近孔口处的活性中心的数量.     

CoAPO-11分子筛的合成、表征和催化性能： 1-己烯异构化反应

水热法合成了钴取代磷铝酸盐分子筛CoAPO-11，并采用了X射线衍射、扫描电子显微镜、红外光谱、紫外可见光谱以及氮气吸脱附等表征手段对合成的样品进行表征，并在合成的分子筛上进行1-己烯异构化反应评价，并考查了温度和空速对反应的影响。结果表明，在反应温度300℃及空速为2.4h－1CoAPO-11分子筛对1-己烯异构化反应具有较好的催化性能。     

不同分子筛上1-己烯骨架异构化反应性能的研究

以HZSM-35、HZSM-5、HM和Hβ四种分子筛为1-己烯骨架异构化催化剂,比较研究了四种催化剂的异构化性能,对其构效关系进行了关联。结果表明,相比于HZSM-5和Hβ分子筛,HZSM-35和HM具有适宜的酸量,有效孔径为0.4-0.6 nm,而且无晶穴、无交叉孔道,具有良好的择形催化效应,在转化率高达95%的同时,C_5-和C₇₊等副产物的收率在20%左右,异己烯收率可达40%-50%。进一步对四种分子筛进行酸碱改性处理,结果显示,虽然酸性质略有改变,但是一维孔结构的HZSM-35和HM分子筛的异构化性能仍明显优于多维孔结构的HZSM-5和Hβ分子筛,说明在酸性质一定的前提下,孔结构对异构化反应起关键作用。     

ZSM-5／MOR复合分子筛催化剂对混合C4烃转化反应的催化性能

以ZSM-5/丝光沸石(MOR)复合分子筛为催化剂,对混合C4烃的催化转化反应进行了评价,并采用程序升温脱附和原位红外光谱技术对ZSM-5/MOR的酸性进行了表征. 结果表明,与ZSM-5相比, MOR具有很低的催化活性,但ZSM-5/MOR复合分子筛具有较高的催化活性,随着ZSM-5/MOR复合分子筛中ZSM-5含量的增加, C4烃转化率稍有升高;在C4烃转化率大致相同的情况下,乙烯和丙烯的总选择性比较接近,但苯和甲苯的总收率却快速升高. 随着ZSM-5/MOR复合分子筛中ZSM-5含量的增加,弱酸和中强酸的酸量逐渐减少,强酸的酸量有所增加. 由于ZSM-5/MOR复合分子筛中MOR对ZSM-5起到分散作用而产生更多的L酸中心,且此L酸中心处于分子筛的外表面而具有较高的能量,导致苯和甲苯的总收率升高.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.