Solid-state metal hydride batteries using ZrO2·nH2O as an electrolyte

ZrO₂·1.5H₂O or ZrO₂·1.5H₂O-KOH composite was used as an electrolyte in order to develop a solid-state nickel-metal hydride battery. The battery using the ZrO₂·1.5H₂O-KOH composite had rechargeability, but had a very low discharge efficiency, even at low current density. However, the performance of the battery was prominently improved by enlarging the electrode-electrolyte interface area. The resultant battery exhibited the remarkably longer cycle life, the higher discharge efficiency, and the lower polarization: it was able to operate over 150 cycles at 10 mA/g alloy.     

Improvement of basic performances of a nickel-metal hydride battery

To develop a sealed-type nickel-metal hydride battery for use in portable equipment or in electric vehicles, investigations were conducted on negative electrodes using AB₅-type hydrogen storage alloy and positive electrodes. For the cycle life performance of the battery, alkaline treatment of the alloy and the substitution of more than 50% to the alloy with Co were effective. For the positive electrode, zinc as a solid solution in the nickel positive electrode obviously prevented γ-NiOOH from being formed in the charging process of β-Ni(OH)₂ and suppressed the migration of the electrolyte solution in the separator to the active material of the positive electrode. Also, hydrophobic treatment of the surface of the alloy was effective to prevent the elevation of the battery internal pressure of the battery in high rate charge.     

Modified graphitized carbon black as transducing material for reagentless H2O2 and enzyme sensors

Direct electron transfer between redox enzymes and electrodes is the basis for the third generation biosensors. We established direct electron transfer between quinohemoprotein alcohol dehydrogenase (PQQ-ADH) and modified carbon black (CBs) electrodes. Furthermore, for the first time, this phenomenon was observed for pyrroloquinoline quinone (PQQ)-dependent glucose dehydrogenase (PQQ-GDH). Reagentless enzyme biosensors suitable for the determination of ethanol, glucose and sensors for hydrogen peroxide were designed using CB electrodes and screen-printing technique. Aiming to create an optimal transducing material for biosensors, a set of CB batches was synthesized using the matrix of Plackett-Burman experimental design. Depending on the obtained surface functional groups as well as the nano-scale carbon structures in CBs batches, the maximal direct electron transfer current of glucose and ethanol biosensors can vary from 20 to 300 nA and from 30 to 6300 nA for glucose and ethanol, respectively. Using modified CB electrodes, an electrocatalytic oxidation of H₂O₂ takes place at more negative potentials (0.1-0.4 V versus Ag/AgCl). Moreover, H₂O₂ oxidation efficiency depends on the amount and morphology of fine fraction in the modified CBs.     

溶胶-凝胶法制备Li3V2(PO4)3及其性能研究

0引言具有类NASICON结构的Li3V2(PO4)3是继过渡金属氧化物LMO后的一种新型的锂离子二次电池正极材料。与目前市场上应用最为广泛的正极材料LiCoO2相比,Li3V2(PO4)3具有超常的稳定性,即使在脱出的Li 与过渡金属原子的物质的量之比大于1的时候仍然具有超乎寻常的稳定性,而通常情况下1mol LiCoO2在脱出0.5mol Li 就会变得不稳定。并且Co是一种战略物资,全球储量十分有限;Co也是一种有毒金属,对于环境污染较为严重。LiNiO2因其合成较为困难而使应用受限,尖晶石LiMn2O4虽然属于环境友好型化合物,但其理论比容量仅为148mAh·g-1,且…     

Effect of intercalation of metal ions on the colloidal and solid properties of vanadium pentaoxide hydrate,V2O5 nH2O

The colloidal stability of V₂O₅ nH₂O was studied on the basis of the measurements of critical flocculation concentration (CFC) by metal ions, amount of ions exchanged (or intercalated), and -potential. In total, the CFC values obeyed the Schulze Hardy law and strong Hofmeister's series was found in the systems including alkaline ions. The sequence of colloidal stability of V₂O₅ nH₂O in the electrolyte solutions was related to the intercalation of metal ions in the interlayer spaces of the solid. The largest CFC value for Li⁺ (87 mmol dm^–3) was explained by smaller affinity of Li⁺ to be intercalated in V₂O₅ nH₂O as well as smaller Hamaker constant of the intercalated solid compared to the other systems.Effect of intercalation of metal ions on the crystalline properties of the materials was measured by use of XRD and electron microscope. Under highly dehydrated condition the ions whose radii are smaller than 0.1 nm are captured in the structure of V₂O₅ nH₂O without changing interlayer distances, while those larger than 0.1 nm increase the interlayer distance. In a saturated H₂O vapor interlayer distances increased with increasing charge of intercalated ions. However, when intercalated with ions carrying the same valency the interlayer distances of the sample decreased with decrease in the hydration property of ions. Hydrolyzable Cr³⁺ gave exceptionally larger interlayer distances, both in a vacuum and in H₂O vapor.     

Alumina-supported cobalt phosphide as a new catalyst for preferential CO oxidation at high temperatures

Abstract

Novel alumina-supported cobalt phosphide catalysts (designated as CoP-3, CoP-10, CoP-20 and CoP-40) prepared from the precursors with Co loadings of 3, 10, 20 and 40?wt% by H₂-temperature-programmed reaction were investigated as potential catalysts for preferential CO oxidation (PROX) in excess H₂ at high temperatures. It was found that the catalytic activities of these Co₂P/γ-Al₂O₃ catalysts were related to their Co loadings. The CoP-10 catalyst showed the best PROX performance in temperature range of 220–240?°C, which was attributed to its optimal microstructures (high surface area, small particle size and big amount of active site).     

Synthesis,characterization of SiO2 supported-industrial phosphoric acid catalyst for hydrolysis of NaBH4 solution

Abstract

Tunisian industrial phosphoric acid H₃PO₄ was supported on silica gel SiO₂ (SIPA) to catalyze the hydrolysis reaction of aqueous alkaline sodium borohydride (NaBH₄). The SiO₂ was produced from purified quartz sand using alkali fusion-acidification chemical process. The BET surface area results indicate that the prepared silica gel could reach a specific surface area up to 585 m²/g. The addition of PO₃H₂ functional groups resulted in an increase of surface acidity of SiO₂ catalyst as shown by FT-IR and DTA-DTG spectra. The total acidity of SIPA catalyst was determined by titration to be 2.8?mmol H⁺/g. SEM/EDS maps reveal the distribution of heavy metals on the silica surface. The effect of supported PO₃H₂ functional groups and heavy metals on the NaBH₄ hydrolysis reaction was studied for different ratios of SIPA catalyst to NaBH₄. The sample 12SIPA/NaBH₄ leads to a very high hydrogen generation rate (up to 90%). The activation energy of hydrogen generation by NaBH₄ hydrolysis was 25.7?kJ mol^?1.     

Theoretical study on H2 elimination pathways of silylenoid H2SiLiF with CH4, NH3, H2O, HF, SiH4, PH3, H2S, and HCl

Ab initio molecular orbital calculations have been performed to explore the reaction potential energy surfaces of silylenoid H₂SiLiF with XH _n hydrides, where XH _n = CH₄, NH₃, H₂O, HF, SiH₄, PH₃, H₂S, and HCl. We have identified a previously unreported reaction pathway on each reaction surface, H₂SiLiF + H-XH _{n − 1} → H _n XSiLiF + H₂, which involves H₂ elimination following the initial formation of an association complex via a four-membered ring transition state to form the substituted three-membered ring silylenoid H _n XSiLiF and a H₂ molecule. This theoretical calculations suggest that (i) for H₂ eliminations there is a very clear trend toward lower activation barriers and more exothermic interactions on going from left to right along a given row in periodic table, and (ii) for the second-row hydrides, the H₂ elimination reactions are less exothermic than for the first-row hydrides and the reaction barriers are lower for X–S and Cl. Compared to the insertions of H₂SiLiF into XH _n , the H₂ elimination pathways should be unfavorable with higher barrier and lower exothermic.     

A pseudopotential study of the hydrogen bond in H2O·H2S,H2S·H2S and H2O·H2Se systems

Intermolecular potential energy curves for the hydrogen bonded systems H₂O·H₂S, H₂O·H₂Se and H₂S·H₂S were calculated with nonempirical pseudopotentials using optimized-in-molecules basis sets augmented by polarization functions. The H₂O·H₂O interaction energy curve has been also considered as a test case. The present results for H₂O·H₂S and H₂S·H₂S indicate much weaker intermolecular interactions than those found in previous ab initio calculations. The H₂O·H₂Se interaction was found to be quite similar to H₂O·H₂S.This work was partly supported by the Polish Academy of Sciences within the Project PAN-09, 7.1.1.1On leave from Quantum Chemistry Laboratory, Dept. of Chemistry, University of Warsaw, Pasteura 1, 02-093. Warsaw, Poland     

掺F影响LiNi0.8Co0.1Mn0.1O2结构和性能的微观机制

以氟化锂为氟源,通过高温固相法合成了F掺杂的LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2。采用X射线衍射仪(XRD)、扫描电镜(SEM)、X射线光电子能谱(XPS)和电化学测试等手段研究F影响LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2结构和性能的微观机制。结果表明:适量F掺杂可以提高正极材料的放电比容量,改善其倍率性、循环性和热稳定性。当F掺杂量(物质的量分数)为1.5%时,材料的综合电化学性能最优,初始放电比容量(0.2C)和50周循环容量保持率(1C)分别由原始的174.0 mAh·g~(-1)(78.7%)提高到178.6 mAh·g~(-1)(85.7%)。LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2材料性能的改善可归因于F能够增强过渡金属层、锂层与氧层之间的结合力,提高材料的结构稳定性。此外,F掺杂还有利于降低电化学反应中的界面电阻和电荷转移阻抗。     

Cerium/Ascorbic Acid/Iodine Active Species for Redox Flow Energy Storage Battery

In this study, we developed a novel cerium/ascorbic acid/iodine active species to design a redox flow battery (RFB), in which the cerium nitrate hexahydrate [Ce(NO₃)₃·6H₂O] was used as a positive Ce³⁺/Ce⁴⁺ ion pair, and the potassium iodate (KIO₃) containing ascorbic acid was used as a negative I₂/I⁻ ion pair. In order to improve the electrochemical activity and to avoid cross-contamination of the redox pair ions, the electroless plating and sol–gel method were applied to modify the carbon paper electrode and the Nafion 117 membrane. The electrocatalytic and electrochemical properties of the composite electrode using methanesulfonic acid as a supporting electrolyte were assessed using the cyclic voltammetry (CV) test. The results showed that the Ce (III)/Ce (IV) active species presented a symmetric oxidation/reduction current ratio (1.09) on the C–TiO₂–PdO composite electrode. Adding a constant amount of ascorbic acid to the iodine solution led to a good reversible oxidation/reduction reaction. Therefore, a novel Ce/ascorbic acid/I RFB was developed with C–TiO₂–PdO composite electrodes and modified Nafion 117–SiO₂–SO₃H membrane using the staggered-type flow channel, of which the energy efficiency (EE%) can reach about 72%. The Ce/ascorbic acid/I active species can greatly reduce the electrolyte cost compared to the all-vanadium redox flow battery system, and it therefore has greater development potential.     

Effect of sulfuric and phosphoric acid pretreatments on enzymatic hydrolysis of corn stover

The pretreatment of corn stover with H₂SO₄ and H₃PO₄ was investigated. Pretreatments were carried out from 30 to 120 min in a batch reactor at 121°C, with acid concentrations ranging from 0 to 2% (w/v) at a solid concentration of 5% (w/v). Pretreated corn stover was washed with distilled water until the filtrate was adjusted to pH 7.0, followed by surfactant swelling of the cellulosic fraction in a 0–10% (w/v) solution of Tween-80 at room temperature for 12 h. The dilute acid treatment proved to be a very effective method in terms of hemicellulose recovery and cellulose digetibility. Hemicellulose recovery was 62–90%, and enzymatic digestibility of the cellulose that remained in the solid was >80% with 2% (w/v) acid. In all cases studied, the performance of H₂SO₄ pretreatment (hemicellulose recovery and cellulose digestibility) was significantly better than obtained with H₃PO₄. Enzymatic hydrolysis was more effective using surfactant than without it, producing 10–20% more sugar. Furthermore, digestibility was investigated as a function of hemicellulose removal. It was found that digestibility was more directly related to hemicellulose removal than to delignification.     

Ti3C2Tx/MnO2正极在水系锌电池中的电化学性能

二氧化锰(MnO₂)材料具有比容量大、电极电位高、储量丰富以及价格低廉等优势,成为水系锌电池正极最受关注的一类材料,然而其仍然存在着结构稳定性差和电化学储存机理复杂的问题。因此,我们通过两步合成法制备了一种花苞状结构的MnO₂负载在Ti₃C₂T_x表面形成Ti₃C₂T_x/MnO₂复合材料,通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)对复合样品的结构、成分和形貌进行表征。通过将Ti₃C₂T_x/MnO₂复合材料作为正极,与锌负极匹配组装成水系锌电池,研究了其分别在2 mol·L^-1 ZnSO₄、2 mol·L^-1 ZnSO₄+0.1 mol·L^-1 MnSO₄、30 mol·L^-1三氟甲基磺酸四乙基铵(TEAOTf)+1 mol·L^-1三氟甲烷磺酸锌(ZnOTf)和3 mol·L^-1 ZnOTf四种电解液中的电化学性能。结果表明,Ti₃C₂T_x/MnO₂在2 mol·L^-1 ZnSO₄中的比容量较高,但循环稳定性很差。将TEAOTf盐和ZnOTf盐共溶于水中,设计了一种新型的含惰性阳离子的超高浓度盐包水电解液(30 mol·L^-1 TEAOTf+1 mol·L^-1 ZnOTf),不仅提高了Ti₃C₂T_x/MnO₂材料的可逆性,而且有效抑制了电极材料在循环过程中的溶解。     

Oxygen Transport in the SOFC Cathode

The impedance of the La_0.75Sr_0.2MnO₃-cathode/electrolyte interface for cathodes with different porosity is measured. The impedance spectra are fitted using a developed model of the oxygen transport at this interface. After the measurements, the cathode is removed from the electrolyte. The contact area and the three-phase boundary length (TPBL) at the interface are estimated from SEM images of the electrolyte surface. The dependence of the interfacial electrical resistance on the microstructure is discussed. It is shown that the bulk diffusion of oxygen vacancies at the interface at 950°C is high enough to use the whole La_0.75Sr_0.2MnO₃/YSZ contact area F for the oxygen transport into the electrolyte for microstructures with 2F/TPBL 2 m. The impact of the surface diffusion of oxygen species on polarization resistance at operation temperatures <900°C is discussed. The polarization resistance and the morphology of composite cathodes made from La_0.75Sr_0.2MnO₃/YSZ and yttria- or scandia-stabilized zirconia powders (3YSZ, 8YSZ, 10ScSZ) are investigated by impedance spectroscopy at 800–950°C. The polarization (interfacial) resistance decreases gradually with addition of electrolyte powder in the uLSM cathode material independent of the electrolyte powder used. The interfacial resistance of the uLSM/3YSZ, uLSM/8YSZ, and uLSM/10ScSZ composite cathodes is almost the same. The interaction between uLSM and doped zirconia particles is discussed on the basis of the interfacial resistance, activation energies, and high-frequency impedance.     

Gram-Scale Synthesis of an Ultrastable Microporous Metal-Organic Framework for Efficient Adsorptive Separation of C2H2/CO2 and C2H2/CH4

A highly water and thermally stable metal-organic framework (MOF) Zn₂(Pydc)(Ata)₂ (1, H₂Pydc = 3,5-pyridinedicarboxylic acid; HAta = 3-amino-1,2,4-triazole) was synthesized on a large scale using inexpensive commercially available ligands for efficient separation of C₂H₂ from CH₄ and CO₂. Compound 1 could take up 47.2 mL/g of C₂H₂ under ambient conditions but only 33.0 mL/g of CO₂ and 19.1 mL/g of CH₄. The calculated ideal absorbed solution theory (IAST) selectivities for equimolar C₂H₂/CO₂ and C₂H₂/CH₄ were 5.1 and 21.5, respectively, comparable to those many popular MOFs. The Q_st values for C₂H₂, CO₂, and CH₄ at a near-zero loading in 1 were 43.1, 32.1, and 22.5 kJ mol⁻¹, respectively. The practical separation performance for C₂H₂/CO₂ mixtures was further confirmed by column breakthrough experiments.     

Comparison of the Surface Dilational Properties of Block Copolymers and Sodium Oleate Using the Oscillating Bubble Method

The surface dilational modulus of the star-like block copolymer AP432 and linear block copolymer L64 was studied using the oscillating bubble method at an accessible frequency range of 0.05 to 2 Hz, which was compared with anionic surfactant sodium oleate (C₁₇H₃₃COONa) and the influence of inorganic salt NaNO₃ on the surface dilational modulus of AP432 and L64 was also studied. The results indicate that for AP432 and L64 the dilational modulus varies slightly, just decrease gradually with concentrations increasing and never reaches high values with the dilational frequency increasing, but the dilational modulus of C₁₇H₃₃COONa increases gradually with the increase of dilational frequency and pass through the maximum values with increasing concentration. The properties of AP432, L64, and C₁₇H₃₃COONa at the air/water interface were also observed by surface tension measurement. Based on these experimental results, a simple possible adsorption model of these molecules at air/water interface is proposed.     

Chemical analysis of acidic silicon etch solutions: I. Titrimetric determination of HNO3, HF, and H2SiF6

The chemical etching of silicon using HF-HNO₃ mixtures is a widely used process in the processing of silicon wafers for microelectronic or photovoltaic applications. The control of the etch bath composition is the necessary condition for an effective bath utilization, for the replenishment of the consumed acids, and to maintain a certain etch rate. The present paper describes two methods for the total analysis of the individual etch bath constituents HF, HNO₃, and H₂SiF₆. Both methods start with an aqueous acid-base titration determining the total acid concentration and the concentration of H₂SiF₆. The first method is an acid-base titration using a 0.1 mol L⁻¹ methanolic solution of cyclohexylamine (CHA) as non-aqueous titrant to determine the content of nitric acid. Then, the amount of hydrofluoric acid is calculated from the difference between the total acid and nitric acid content. The second method is based on the determination of the total fluoride concentration using a fluoride ion-selective electrode (F-ISE). The content of hydrofluoric acid is obtained from the difference between the total fluoride content and the amount of fluoride bound as H₂SiF₆. The amount of nitric acid results finally calculated as difference to the total acid content.     

Li2S-P2S5体系电解质及其在全固态锂离子电池中的应用研究进展

全固态锂离子电池具有安全性能好、能量密度高、工作温区广等优点,被广泛应用于便携式电子设备。固态电解质是全固态锂离子电池的关键材料之一,其中的硫化物电解质具有离子电导率高、电化学窗口宽、晶界电阻低和易成膜等特点,被认为最有希望应用于全固态锂离子电池。本文综述了Li_2S-P_2S_5体系电解质的发展状况,包括固态电解质的制备、改性、表征以及电极/固态电解质之间的固-固界面的稳定兼容问题。本文还涉及了以Li_2S-P_2S_5为电解质的全固态锂离子电池性能的研究进展。     

致密的5%Al3+掺杂的SnP2O7-SnO2复合陶瓷在中温燃料电池中的应用

首先制备了未掺杂和5%(摩尔分数)Al³⁺掺杂SnO₂的多孔性基片, 然后将基片与85%的H₃PO₄在600℃下反应, 分别得到了致密的未掺杂和5%Al³⁺掺杂的SnP₂O₇-SnO₂复合陶瓷样品. 采用X射线衍射(XRD), 扫描电子显微镜(SEM)和X射线能量色散谱(EDS)测试方法对样品进行了表征, 采用电化学阻抗谱法(EIS)测试了样品在中温(100-250℃)下, 湿润空气和湿润氢气气氛中的电导率. 结果表明, 在湿润空气和湿润氢气中, 5%Al³⁺掺杂的SnP₂O₇-SnO₂复合陶瓷样品的电导率均高于未掺杂的SnP₂O₇-SnO₂复合陶瓷样品的电导率, 且该复合陶瓷样品在湿润空气和湿润氢气中250℃下, 电导率分别达到最大值: 4.30×10^-2和6.25×10^-2 S·cm^-1, 高于至今报道的SnP₂O₇-SnO₂基复合陶瓷及SnP₂O₇基陶瓷在类似条件下的电导率. 以5%Al³⁺掺杂的SnP₂O₇-SnO₂复合陶瓷样品(厚度: 1.45 mm)为电解质, 多孔性铂为电极组装成的氢气/空气燃料电池具有良好的中温电池性能, 175、200、250℃的最大输出功率密度分别为52.0、61.9、82.3 mW·cm^-2. 良好的中温电池性能与该复合陶瓷电解质较高的电导率和致密度及该燃料电池较低的界面极化电阻有关.