Transport properties of MoS<Subscript>2</Subscript> nanoribbons: edge priority

We report about results from density functional based calculations on structural, electronic and transport properties of one-dimensional MoS₂ nanoribbons with different widths and passivation of their edges. The edge passivation influences the electronic and transport properties of the nanoribbons. This holds especially for nanoribbons with zigzag edges. Nearly independent from the passivation the armchair MoS₂ nanoribbons are semiconductors and their band gaps exhibit an almost constant value of 0.42 eV. Our results illustrate clearly the edge priority on the electronic properties of MoS₂ nanoribbons and indicate problems for doping of MoS₂ nanoribbons.     

The rise of two-dimensional MoS<Subscript>2</Subscript> for catalysis

Two-dimensional (2D) MoS₂ is used as a catalyst or support and has received increased research interest because of its superior structural and electronic properties compared with those of bulk structures. In this article, we illustrate the active sites of 2D MoS₂ and various strategies for enhancing its intrinsic catalytic activity. The recent advances in the use of 2D MoS₂-based materials for applications such as thermocatalysis, electrocatalysis, and photocatalysis are discussed. We also discuss the future opportunities and challenges for 2D MoS₂-based materials, in both fundamental research and industrial applications.     

Photodeposition of ultrathin MoS<Subscript>2</Subscript> nanosheets onto cubic CdS for efficient photocatalytic H<Subscript>2</Subscript> evolution

In this work, the photocatalyst composed of ultrathin MoS₂ nanosheets onto the surface of cubic CdS nanoparticles with an average diameter of 7~10 nm has been successfully fabricated through a facile and mild photodeposition route. The ultrathin MoS₂ nanosheets as a cocatalyst were demonstrated to greatly boost photocatalytic H₂ evolution over cubic CdS upon visible light irradiation. It was clearly revealed that both the cubic CdS substrate and structure of ultrathin MoS₂ nanosheets play critical roles in the observed efficient H₂ evolution. The cubic CdS offers a strong adherence for ultrathin MoS₂ nanosheets to form a well contact interface, across which the photogenerated charge transfer and charge separation are achieved. The ultrathin MoS₂ nanosheets introduce a high density of unsaturated active S atoms for H₂ evolution.     

Electronic and optical properties of single-layer MoS<Subscript>2</Subscript>

The electronic structures of a MoS₂ monolayer are investigated with the all-electron first principle calculations based on the density functional theory (DFT) and the spin-orbital couplings (SOCs). Our results show that the monolayer MoS₂ is a direct band gap semiconductor with a band gap of 1.8 eV. The SOCs and d-electrons in Mo play a very significant role in deciding its electronic and optical properties. Moreover, electronic elementary excitations are studied theoretically within the diagrammatic self-consistent field theory. Under random phase approximation, it shows that two branches of plasmon modes can be achieved via the conduction-band transitions due to the SOCs, which are different from the plasmons in a two-dimensional electron gas and graphene owing to the quasi-linear energy dispersion in single-layer MoS₂. Moreover, the strong optical absorption up to 10⁵ cm^-1 and two optical absorption edges I and II can be observed. This study is relevant to the applications of monolayer MoS₂ as an advanced photoelectronic device.     

Generation of MoS<Subscript>2</Subscript> quantum dots by laser ablation of MoS<Subscript>2</Subscript> particles in suspension and their photocatalytic activity for H<Subscript>2</Subscript> generation

MoS₂ quantum dots (QDs) have been obtained in colloidal suspensions by 532 nm laser ablation (7 ns fwhp/pulse, 50 mJ/pulse) of commercial MoS₂ particles in acetonitrile. High-resolution transmission electron microscopy images show a lateral size distribution from 5 to 20 nm, but a more homogeneous particle size of 20 nm can be obtained by silica gel chromatography purification in acetonitrile. MoS₂ QDs obtained by laser ablation are constituted by 3–6 MoS₂ layers (1.8–4 nm thickness) and exhibit photoluminescence whose λ_PL varies from 430 to 530 nm depending on the excitation wavelength. As predicted by theory, the confinement effect and the larger periphery in MoS₂ QDs increasing the bandgap and having catalytically active edges are reflected in an enhancement of the photocatalytic activity for H₂ generation upon UV–Vis irradiation using CH₃OH as sacrificial electron donor due to the increase in the reduction potential of conduction band electrons and the electron transfer kinetics.     

Facile growth of monolayer MoS<Subscript>2</Subscript> film areas on SiO<Subscript>2</Subscript>

Areas of single-layer MoS₂ film can be prepared in a tube furnace without the need for temperature control. The films were characterized by means of Raman spectroscopy, photoluminescence, low-energy electron diffraction and microscopy, and X-ray photoelectron spectroscopy and mapping. Transport measurements show n-doped material with a mobility of 0.26 cm² V^-1 s^-1.     

Facial synthesis of carbon-coated ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene and their enhanced lithium storage properties

Carbon-coated ZnFe₂O₄ spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g^?1 and maintains a reversible capacity of 775 mAh g^?1 after 150 cycles at a current density of 500 mA g^?1. After being tested at 2 A g^?1 for 700 cycles, the capacity still retains 617 mAh g^?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe₂O₄ spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.

Open image in new window

Graphical abstract ?

     

Structural transformation of MoO<Subscript>3</Subscript> nanobelts into MoS<Subscript>2</Subscript> nanotubes

The structural transformation of MoO₃ nanobelts into MoS₂ nanotubes using a simple sulfur source has been reported. This transformation has been extensively investigated using electron microscopic and spectroscopic techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), electron diffraction (ED), and energy-dispersive X-ray analysis (SEM-EDAX and TEM-EDX). The method described in this report will serve as a generic route for the transformation of other oxide nanostructures into the chalcogenide nanostructures.     

Synthesis and lithium-ion storage performances of LiFe<Subscript>0.5</Subscript>Co<Subscript>0.5</Subscript>PO<Subscript>4</Subscript>/C nanoplatelets and nanorods

Carbon-coated olivine-structured LiFe_0.5Co_0.5PO₄ solid solution was synthesized by a facile rheological phase method and applied as cathode materials of lithium-ion batteries. The nanostructure’s properties, such as morphology, component, and crystal structure for the samples, characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer, Emmett, and Teller (BET) determination, X-ray photoelectron spectroscopy (XPS), and the electrochemical performances were evaluated using constant current charge/discharge tests and electrochemical impedance spectroscopy (EIS). The results indicate that nanoplatelet- and nanorod-structured LiFe_0.5Co_0.5PO₄/C composites were separately obtained using stearic acid or polyethylene glycol 400 (PEG400) as carbon source, and the surfaces of particles for the two samples are ideally covered by full and uniform carbon layer, which is beneficial to improving the electrochemical behaviors. Electrochemical tests verify that the nanoplatelet LiFe_0.5Co_0.5PO₄/C shows a better capacity capability, delivering a discharge specific capacity of 133.8, 112.1, 98.3, and 74.4 mAh g^?1 at 0.1, 0.5, 1, and 5 C rate (1 C?=?150 mA g^?1); the corresponding cycle number is 5th, 11th, 15th, 20th, and 30th, respectively, whereas the nanorod one possesses more excellent cycling ability, with a discharge capacity of 83.3 mAh g^?1 and capacity retention of 86.9% still maintained after cycling for 100 cycles at 0.5 C. Results from the present study demonstrate that the LiFe_0.5Co_0.5PO₄ solid solution nanomaterials with favorable carbon coating effect combine the characteristics and advantage of LiFePO₄ and LiCoPO₄, thus displaying a tremendous potential as cathode of lithium-ion battery.     

Synthesis and structural determination of twisted MoS<Subscript>2</Subscript> nanotubes

In the present work we report the synthesis of MoS₂ nanotubes with diameters greater than 10 nm using a template method. The length and properties of these nanotubes are a direct result of the preparation method. High-resolution transmission electron microscopy is used to study the structure of these highly curved entities. Molecular dynamics simulations of MoS₂ nanotubes reveal that one of the stable forms of the nanotubes is a twisted one. The twisting of the nanotubes produces a characteristic contrast in the images, which is also studied using simulation methods. The analysis of the local contrast close to the perpendicular orientation shows geometrical arrays of dots in domain-like structures, which are demonstrated to be a product of the atomic overlapping of irregular curvatures in the nanotubes. The configuration of some of the experimentally obtained nanotubes is demonstrated to be twisted with a behavior suggesting partial plasticity. PACS 61.16.Bg; 79.60.Jv; 61.46.+w; 61.50.Ah     

Synthesis and electrochemical characterization of graphene nanoflakes and LiFe<Subscript>0.97</Subscript>Ni<Subscript>0.03</Subscript>PO<Subscript>4</Subscript>/C for lithium-ion battery

The graphene nanoflakes and olivine-type LiFe_0.97Ni_0.03PO₄/C (LFNP3/C) samples have been synthesized as anode and cathode materials, respectively. Physicochemical characterization of the graphene nanoflakes and LFNP3/C material were studied using X-ray diffraction (XRD) and scanning electron microscope (SEM). The XRD patterns reveal the formation of the pure phase of both the synthesized samples. SEM micrographs disclose the formation of spherically shaped nanosized particles for LFNP3/C while graphene shows flake-type morphology. CR2032 half and full coin cells were assembled for electrochemical testing of the synthesized samples. Cyclic voltammetry (CV) results indicate that the graphene-based half-cells, i.e., GN1H and GN2H, possess reduction peak/plateau around 0.17 V while LFNP3/C cathode shows discharging voltage plateau at 3.4 V vs. Li/Li⁺. The discharge capacities were found to be 700, 900, and 153 mAhg^?1 for GN1H, GN2H, and LFNP3/C half-cells vs. Li/Li⁺, respectively. Among full cells, LFPGN1F with γ = 0.75 (mass/capacity balancing factor) shows better charging/discharging profile at each C-rate as compared to LFPGN2F with γ = 0.55. LFPGN1F delivered an initial discharge capacity of around 154 mAhg^?1 at 0.1C and even at a high discharge rate of 1C, it retained ~97% of the discharge capacity as compared to the initial cycle at the same rate.     

Enhanced lithium storage performance of a self-assembled hierarchical porous Co<Subscript>3</Subscript>O<Subscript>4</Subscript>/VGCF hybrid high-capacity anode material for lithium-ion batteries

A Co₃O₄/vapor-grown carbon fiber (VGCF) hybrid material is prepared by a facile approach, namely, via liquid-phase carbonate precipitation followed by thermal decomposition of the precipitate at 380 °C for 2 h in argon gas flow. The material is characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller specific surface area analysis, and carbon elemental analysis. The Co₃O₄ in the hybrid material exhibits the morphology of porous submicron secondary particles which are self assembled from enormous cubic-phase crystalline Co₃O₄ nanograins. The electrochemical performance of the hybrid as a high-capacity conversion-type anode material for lithium-ion batteries is investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic discharge/charge methods. The hybrid material demonstrates high specific capacity, good rate capability, and good long-term cyclability, which are far superior to those of the pristine Co₃O₄ material prepared under similar conditions. For example, the reversible charge capacities of the hybrid can reach 1100–1150 mAh g^?1 at a lower current density of 0.1 or 0.2 A g^?1 and remain 600 mAh g^?1 at the high current density of 5 A g^?1. After 300 cycles at 0.5 A g^?1, a high charge capacity of 850 mAh g^?1 is retained. The enhanced electrochemical performance is attributed to the incorporated VGCFs as well as the porous structure and the smaller nanograins of the Co₃O₄ active material.     

Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

Flower-like MoS<Subscript>2</Subscript> supported on three-dimensional graphene aerogels as high-performance anode materials for sodium-ion batteries

Flower-like MoS₂ supported on three-dimensional graphene aerogel (MoS₂/GA) composite has been prepared by a facile hydrothermal method followed by subsequent heat-treatment process. Each of MoS₂ microflowers is surrounded by the three-dimensional graphene nanosheets. The MoS₂/GA composite is applied as an anode material of sodium-ion batteries (SIBs) and it exhibits high initial discharge/charge capacities of 562.7 and 460 mAh g^?1 at a current density of 0.1 A g^?1 and good cycling performance (348.6 mAh g^?1 after 30 cycles at 0.1 A g^?1). The good Na⁺ storage properties of the MoS₂/GA composite could be attributed to the unique structure which flower-like MoS₂ are homogeneously and tightly decorated on the surface of three-dimensional graphene aerogel. Our results demonstrate that as-prepared MoS₂/GA composite has a great potential prospect as anodes for SIBs.     

The interfacial properties of SrRuO<Subscript>3</Subscript>/MoS<Subscript>2</Subscript> heterojunction: a first-principles study

First-principles calculation was used to study the interfacial properties of theSrRuO₃ (1 1 1)/MoS₂(√3 × √3) heterojunction. It is found that the huge magneticmoments in of monolayer MoS₂ largely originate from the Ru-S hybridization for theRu-terminated interface. Moreover, for the SrO-terminated interface, we studied mainly themetal and semiconductor contact characteristic. The calculated results show that theSchottky barrier height can be significantly reduced to zero for the SrO-terminatedinterface. Schottky barrier heights dominate the transport behavior of theSrRuO₃/MoS₂ interface. Our results not only have potentialapplications in spintronics devices, but also are in favour of the scaling of field effecttransistors.     

Synthesis of hierarchical nanospheres Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/graphene composite and its application in lithium-ion battery as a high-performance anode material

A hierarchically nanospherical α-Fe₂O₃/graphene composite with a homogeneous mono-pore size of 4 nm has been prepared using a hydrothermal method. The composite showed an extremely high rate performance and good cycling stability when applied as an anode material for lithium-ion batteries owing to its unique three dimensional architecture. A specific capacity of 110 mAh/g was obtained at an extremely high current rate of 40 A/g and recover to 830 mAh/g at 0.5 A/g after 60 cycles. After 250 cycles at 2 A/g, the composite electrode exhibited a capacity of 630 mAh/g with a columbic efficiency of 99.5 %.     

Enhanced electrochemical properties and thermal stability of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by surface modification with Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>

Layered LiNi_1/3Co_1/3Mn_1/3O₂ cathode material is synthesized via a sol-gel method and subsequently surface-modified with Eu₂O₃ layer by a wet chemical process. The effect of Eu₂O₃ coating on the electrochemical performances and thermal stability of LiNi_1/3Co_1/3Mn_1/3O₂@Eu₂O₃ cells is investigated systematically by the charge/discharge testing, cyclic voltammograms, AC impedance spectroscopy, and DSC measurements, respectively. In comparison, the Eu₂O₃-coated sample demonstrates better electrochemical performances and thermal stability than that of the pristine one. After 100 cycles at 1C, the Eu₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode demonstrates stable cyclability with capacity retention of 92.9 %, which is higher than that (75.5 %) of the pristine one in voltage range 3.0–4.6 V. Analysis from the electrochemical measurements reveals that the remarkably improved performances of the surface-modified composites are mainly ascribed to the presence of Eu₂O₃-coating layer, which could efficiently suppress the undesirable side reaction and increasing impedance, and enhance the structural stability of active material.     

Ionic displacements and structure of disordered PbFe<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>O<Subscript>3</Subscript>

A sequence of structural models of unit cells of complex oxides with perovskite-type structure has been constructed to refine the average structure of PbFe_1/2Nb_1/2O₃ (PFN) at temperatures above the ferroelectric Curie point (T _C ～ 110°C). Owing to the analysis of the probability theory considerations, each model is characterized by only two positional fitting parameters. With the use of the intensities of 95 symmetrically independent X-ray reflections from a PFN single crystal at 160°C, a model with the R factor below 3% (K = 2.44%) was chosen. The ravine method has been used to verify the existence of a single minimum for the R factor with respect to the fitting parameter.     

Electronic and transport properties of heterophase compounds based on MoS<Subscript>2</Subscript>

New heterophase superlattices based on MoS₂ are studied in detail by the electron density functional theory. It is shown that the incorporation of the 1Т phase in the 2H-MoS₂ monolayer is responsible for the formation of electronic levels near the Fermi level and quantum wells in the transverse direction of superlattices. The proposed lateral heterophase structures of transition metal dichalcogenides are promising for the construction of new elements of nanoelectronics.