Evaluations of SGS Combustion,Scalar Flux and Stress Models in a Turbulent Jet Premixed Flame

A newly developed fractal dynamic SGS (FDSGS) combustion model and a scale self-recognition mixed (SSRM) SGS stress model are evaluated along with other SGS combustion, scalar flux and stress models in a priori and a posteriori manners using DNS data of a hydrogen-air turbulent plane jet premixed flame. A posteriori tests reveal that the LES using the FDSGS combustion model can predict the combustion field well in terms of mean temperature distributions and peak positions in the transverse distributions of filtered reaction progress variable fluctuations. A priori and a posteriori tests of the scalar flux models show that a model proposed by Clark et al. accurately predicts the counter-gradient transport as well as the gradient diffusion, and introduction of the model of Clark et al. into the LES yields slightly better predictions of the filtered progress variable fluctuations than that of a gradient diffusion model. Evaluations of the stress models reveal that the LES with the SSRM model predicts the velocity fluctuations well compared to that with the Smagorinsky model.     

Measurements of Turbulent Jet Mixing in a Turbulent Co-Flow Including the Influence of Periodic Forcing and Heating

In this work, the turbulent mixing of a confined coaxial jet in air is investigated by means of simultaneous particle image velocimetry and planar laser induced fluorescence of the acetone seeded flow injection. The jet is injected into a turbulent duct flow at atmospheric pressure through a 90 ^° pipe bend. Measurements are conducted in a small scale windtunnel at constant mass flow rates and three modes of operation: isothermal steady jet injection at a Dean number of 20000 (R e _d =32000), pulsed isothermal injection at a Womersley number of 65 and steady injection at elevated jet temperatures of ΔT=50 K and ΔT=100 K. The experiment is aimed at providing statistically converged quantities of velocity, mass fraction, turbulent fluctuations and turbulent mass flux at several downstream locations. Stochastic error convergence over the number of samples is assessed within the outer turbulent shear layer. From 3000 samples the statistical error of time-averaged velocity and mass fraction is below 1 % while the error of Reynolds shear stress and turbulent mass flux components is in the of range 5-6 %. Profiles of axial velocity and turbulence intensity immediately downstream of the bend exit are in good agreement with hot-wire measurements from literature. During pulsed jet injection strong asymmetric growing of shear layer vortices lead to a skewed mass fraction profile in comparison with steady injection. Phase averaging of single shot PLIF-PIV measurements allows to track the asymmetric shear layer vortex evolvement and flow breakdown during a pulsation cycle with a resolution of 10^°. Steady injection with increased jet temperature supports mixing downstream from 6 nozzle diameters onward.     

Pre-Chamber Ignition Mechanism: Simulations of Transient Autoignition in a Mixing Layer Between Reactants and Partially-Burnt Products

The structure of autoignition in a mixing layer between fully-burnt or partially-burnt combustion products from a methane-air flame at ? = 0.85 and a methane-air mixture of a leaner equivalence ratio has been studied with transient diffusion flamelet calculations. This configuration is relevant to scavenged pre-chamber natural-gas engines, where the turbulent jet ejected from the pre-chamber may be quenched or may be composed of fully-burnt products. The degree of reaction in the jet fluid is described by a progress variable c (c = taking values 0.5, 0.8, and 1.0) and the mixing by a mixture fraction ξ (ξ = 1 in the jet fluid and 0 in the CH₄-air mixture to be ignited). At high scalar dissipation rates, N₀, ignition does not occur and a chemically-frozen steady-state condition emerges at long times. At scalar dissipation rates below a critical value, ignition occurs at a time that increases with N₀. The flame reaches the ξ = 0 boundary at a finite time that decreases with N₀. The results help identify overall timescales of the jet-ignition problem and suggest a methodology by which estimates of ignition times in real engines may be made.     

Vortical structures behind a transverse jet in a supersonic flow at high jet to crossflow pressure ratios

A three-dimensional supersonic turbulent flow with symmetric normal injection of circular jets from the channel walls is numerically simulated. The initial Favre-averaged Navier–Stokes equations closed by the k–ω turbulence model are solved by an algorithm based on an ENO scheme. The mechanism of the formation of vortical structures due to the interaction of the jet with the free stream is studied for jet to crossflow total pressure ratios ranging from 3 to 50. It is known from experiments reported in the literature that, for n ? 10, mixing of the jet with the high-velocity flow leads to the formation of a pair of vortices and of an additional separation zone near the wall behind the jet. It is demonstrated that the present numerical results are consistent with such findings and that the pressure distribution on the wall ahead of the jet in the plane of symmetry is also in reasonable agreement with available experimental data.     

Large-eddy and unsteady RANS simulations of a shock-accelerated heavy gas cylinder

Two-dimensional numerical simulations of the Richtmyer–Meshkov unstable “shock-jet” problem are conducted using both large-eddy simulation (LES) and unsteady Reynolds-averaged Navier–Stokes (URANS) approaches in an arbitrary Lagrangian–Eulerian hydrodynamics code. Turbulence statistics are extracted from LES by running an ensemble of simulations with multimode perturbations to the initial conditions. Detailed grid convergence studies are conducted, and LES results are found to agree well with both experiment and high-order simulations conducted by Shankar et al. (Phys Fluids 23, 024102, 2011). URANS results using a k–L approach are found to be highly sensitive to initialization of the turbulence lengthscale L and to the time at which L becomes resolved on the computational mesh. It is observed that a gradient diffusion closure for turbulent species flux is a poor approximation at early times, and a new closure based on the mass-flux velocity is proposed for low-Reynolds-number mixing.     

Reynolds-Averaged,Scale-Adaptive and Large-Eddy Simulations of Premixed Bluff-Body Combustion Using the Eddy Dissipation Concept

A lean premixed propane/air bluff-body stabilized flame (Volvo test rig) is calculated using the Scale-Adaptive Simulation turbulence model (SAS) and Large-Eddy simulations (LES) as well as the conventional Reynolds-averaged approach (RAS). RAS and SAS are closed by the standard k-?? and the k-ω Shear Stress Transport (SST) turbulence models, respectively. The conventional Smagorinsky and the k-equation sub-grid scales models are used for the LES closure. Effects of the sub-grid scalar flux modeling using the classical gradient hypothesis and Clark’s tensor diffusivity closures both for the inert and reactive LES flows are discussed. The Eddy Dissipation Concept (EDC) is used for the turbulence-chemistry interaction. It assumes that molecular mixing and the subsequent combustion occur in the ’fine structures’ (smaller dissipative eddies, which are close to the Kolmogorov scales). Assuming the full turbulence energy cascade, the characteristic length and velocity scales of the ’fine structures’ are evaluated using different turbulence models (RAS, SAS and LES). The finite-rate chemical kinetics is taken into account by treating the ’fine structures’ as constant pressure and adiabatic homogeneous reactors, calculated as a system of ordinary-differential equations (ODEs) described by a Perfectly Stirred Reactor (PSR) concept. Several further enhancements to model the PSRs are proposed, including a new Livermore Solver (LSODA) for integrating stiff ODEs and a new correction to calculate the PSR time scales. All models have been implemented as a stand-alone application \(\text {edcPisoFoam}\) based on the OpenFOAM technology. Additionally, several RAS calculations were performed using the Turbulence Flame Speed Closure model in Ansys Fluent to assess effects of the heat losses by modeling the conjugate heat transfer between the bluff-body and the reactive flow. Effects of the turbulence Schmidt number on RAS results are discussed as well. Numerical results are compared with available experimental data. Reasonable consistency between experimental data and numerical results provided by RAS, SAS and LES is observed. In general, there is satisfactory agreement between present LES-EDC simulations, numerical results by other authors and measurements without any major modification to the EDC closure constants, which gives a quite reasonable indication on the adequacy and accuracy of the method and its further application for turbulent premixed combustion simulations.     

Numerical simulation of the interaction of a transverse jet with a supersonic flow using different turbulence models

This paper presents a numerical simulation of the flow resulting from transverse jet injection into a supersonic flow through a slot nozzle at different pressures in the injected jet and the crossflow. Calculations on grids with different resolutions use the Spalart–Allmaras turbulence model, the k–ε model, the k–ω model, and the SST model. Based on a comparison of the calculated and experimental data on the wall pressure distribution, the length of the recirculation area, and the depth of jet penetration into the supersonic flow, conclusions are made on the accuracy of the calculation results for the different turbulence models and the applicability of these models to similar problems.     

Turbulent transport in an inclined jet in crossflow

The present study experimentally investigates a turbulent jet in crossflow relevant to film cooling applications. The jet is inclined at 30°, and its mean velocity is the same as the crossflow. Magnetic resonance imaging is used to obtain the full three-dimensional velocity and concentration fields, whereas Reynolds stresses are obtained along selected planes by Particle Image Velocimetry. The critical role of the counter-rotating vortex pair in the mixing process is apparent from both velocity and concentration fields. The jet entrainment is not significantly higher than in an axisymmetric jet without crossflow, because the proximity of the wall inhibits the turbulent transport. Reynolds shear stresses correlate with velocity and concentration gradients, consistent with the fundamental assumptions of simple turbulence models. However the eddy viscosity is strongly anisotropic and non-homogeneous, being especially low along the leeward side of the jet close to injection. Turbulent diffusion acts to decouple mean velocity and concentration fields, as demonstrated by the drop in concentration flux within the streamtube issued from the hole. Volume-averaged turbulent diffusivity is calculated using a mass–flux balance across the streamtube emanating from the jet hole, and it is found to vary slowly in the streamwise direction. The data are compared with Reynolds-Averaged Navier–Stokes simulations with standard k − ε closure and an optimal turbulent Schmidt number. The computations underestimate the strength of the counter-rotating vortex pair, due to an overestimated eddy viscosity. On the other hand the entrainment is increasingly underpredicted downstream of injection. To capture the correct macroscopic trends, eddy viscosity and eddy diffusivity should vary spatially in different ways. Therefore a constant turbulent Schmidt number formulation is inadequate for this flow.     

Experimental and Theoretical Sensitivity Analysis of Turbulent Flow Past a Square Cylinder

The Siemens SGT-800 3^rd generation DLE burner fitted to an atmospheric combustion rig has been numerically investigated. Pure methane and methane enriched by 80 vol% hydrogen flames have been considered. A URANS (Unsteady Reynolds Averaged Navier-Stokes) approach was used in this study along with the k ? ω SST and the k ? ω SST-SAS models for the turbulence transport. The chemistry is coupled to the turbulent flow simulations by the use of a laminar flamelet library combined with a presumed PDF. The effect of the mesh density in the mixing and the flame region and the effect of the turbulence model and reaction rate model constant are first investigated for the methane/air flame case. The results from the k ? ω SST-SAS along with flamelet libraries are shown to be in excellent agreement with experimental data, whereas the k ? ω SST model is too dissipative and cannot capture the unsteady motion of the flame. The k ? ω SST-SAS model is used for simulation of the 80 vol% hydrogen enriched flame case without further adjusting the model constants. The global features of the hydrogen enrichment are very well captured in the simulations using the SST-SAS model. With the hydrogen enrichment the time averaged flame front location moves upstream towards the burner exit nozzle. The results are consistent with the experimental observations. The model captures the three dominant low frequency unsteady motion observed in the experiments, indicating that the URANS/LES hybrid model indeed is capable of capturing complex, time dependent, features such as an interaction between a PVC and the flame front.     

Effect of Multilateral Jet Mixing on Stability and Structure of Turbulent Partially-Premixed Flames

An experimental study was conducted to investigate the effects of multilateral jet mixing, using both three and four side-jets, on the structure and stability of turbulent partially-premixed flames. Particle Image Velocimetry and OH*-chemiluminescence were used to study the effects of geometry and operating conditions on the resulting flow-field and reaction zone structures, respectively. These effects were compared under varying ratios of side-jet to primary flow momentum, whilst keeping the bulk flow constant. It was found that the mixing regimes upstream of the nozzle exit affect the flame characteristics, i.e. an impinging regime is likely to generate a lifted flame whilst a backflow regime is likely to generate an attached flame. Unlike the 4 side-jets cases, the OH* images and v _{r m s} profiles for the 3 side-jets cases show distinct asymmetry, with intense OH* and low velocity fluctuations on the opposite sides of the fuel injection. It was also found that the flow and scalar fields become independent of the upstream conditions, for both 3 and 4 side-jets, after one diameter downstream of the nozzle exit.     

Assessment of Five SGS Models for Low-Rem MHD Turbulence

Assessment of three regularization-based and two eddy-viscosity-based subgrid-scale (SGS) turbulence models for large eddy simulations (LES) are carried out in the context of magnetohydrodynamic (MHD) decaying homogeneous turbulence (DHT) with a Taylor scale Reynolds number (Re_λ) of 120 and a MHD transition-to-turbulence Taylor-Green vortex (TGV) problems with a Reynolds number of 3000, through direct comparisons to direct numerical simulations (DNS). Simulations are conducted using the low-magnetic Reynolds number approximation (Re_m<<1). LES predictions using the regularization-based Leray- α,LANS- α, and Clark- α SGS models, along with the eddy viscosity-based non-dynamic Smagorinsky and the dynamic Smagorinsky models are compared to in-house DNS for DHT and previous results for TGV. With regard to the regularization models, this work represents their first application to MHD turbulence. Analyses of turbulent kinetic energy decay rates, energy spectra, and vorticity fields made between the varying magnetic field cases demonstrated that the regularization models performed poorly compared to the eddy-viscosity models for all MHD cases, but the comparisons improved with increase in magnitude of magnetic field, due to a decrease in the population of SGS eddies within the flow field.     

Effects of Lewis Number on Head on Quenching of Turbulent Premixed Flames: A Direct Numerical Simulation Analysis

The head on quenching of statistically planar turbulent premixed flames by an isothermal inert wall has been analysed using three-dimensional Direct Numerical Simulation (DNS) data for different values of global Lewis number Le(0.8, 1.0 and 1.2) and turbulent Reynolds number Re_t. The statistics of head on quenching have been analysed in terms of the wall Peclet number Pe (i.e. distance of the flame from the wall normalised by the Zel’dovich flame thickness) and the normalised wall heat flux Φ. It has been found that the maximum (minimum) value of Φ(Pe) for the turbulent Le=0.8 cases are greater (smaller) than the corresponding laminar value, whereas both Pe and Φ in turbulent cases remain comparable to the corresponding laminar values for Le=1.0 and 1.2. Detailed physical explanations are provided for the observed Le dependences of Pe and Φ. The existing closure of mean reaction rate \(\overline {\dot {\omega }}\) using the scalar dissipation rate (SDR) in the near wall region has been assessed based on a-priori analysis of DNS data and modifications to the existing closures of mean reaction rate and SDR have been suggested to account for the wall effects in such a manner that the modified closures perform well both near to and away from the wall.     

Evaluation of the Spectral Element Dynamic Model for Large-Eddy Simulation on Unstructured,Deformed Meshes

In this paper, the Spectral-Element Dynamic Model (SEDM), suited for Large-Eddy Simulation (LES) using Discontinuous Finite Element Methods (DFEM), is assessed using unstructured meshes. Five test cases of increasing complexity are considered, namely, the Taylor-Green vortex at Re =?5000, the turbulent channel flow at Re_τ =?587, the circular cylinder in cross-flow at Re_D =?3900, the square cylinder in cross-flow at Re_D =?22400 and the channel with periodic constrictions at Re_h =?10595. Various discretization parameters such as the grid spacing, polynomial degree and numerical flux are assessed and very accurate results are reported in all cases. This consistency in the results demonstrates the versatility of the SEDM approach and its ability to gage the actual resolution and quality of the mesh and, accordingly, to introduce an amount of sub-grid dissipation which is adapted to the spatial discretization considered.     

A Simple Approach for Specifying Velocity Inflow Boundary Conditions in Simulations of Turbulent Opposed-Jet Flows

A new methodology is developed to specify inflow boundary conditions for the velocity field at the nozzle exit planes in turbulent counterflow simulations. The turbulent counterflow configuration consists of two coaxial opposed nozzles which emit highly-turbulent streams of varying species compositions depending on the mode considered. The specification of velocity inflow boundary conditions at the nozzle exits in the counterflow configuration is non-trivial because of the unique turbulence field generated by the turbulence generating plates (TGPs) upstream of the nozzle exits. In the method presented here, a single large-eddy simulation (LES) is performed in a large domain that spans the region between the TGPs of the nozzles, and the time series of the velocity fields at the nozzle exit planes are recorded. To provide inflow boundary conditions at the nozzle exit planes for simulations under other conditions (e.g., different stream compositions, bulk velocity, TGP location), transformations are performed on the recorded time series: the mean and r.m.s. (root-mean-square) quantities of velocity, as well as the longitudinal integral length scale on the centerline, at the nozzle exits in simulations are matched to those observed in experiments, thereby matching the turbulent Reynolds number R e _t . The method is assessed by implementing it in coupled large-eddy simulation/probability density function (LES/PDF) simulations on a small cylindrical domain between the nozzle exit planes for three different modes of the counterflow configuration: N ₂ vs. N ₂; N ₂ vs. hot combustion products; and C H ₄/N ₂ vs. O ₂. The inflow method is found to be successful as the first and second moments of velocity from the LES/PDF simulations agree well with the experimental data on the centerline for all three modes. This simple yet effective inflow strategy can be applied to eliminate the computational cost required to simulate the flow field upstream of the nozzle exits. It is also emphasized that, in addition to the predicted time series data, the availability of experimental data close to the nozzle exit planes plays a key role in the success of this method.     

Analysis of the Combined Modelling of Sub-grid Transport and Filtered Flame Propagation for Premixed Turbulent Combustion

Flame surface density (FSD) based reaction rate closure is an important methodology of turbulent premixed flame modelling in the context of Large Eddy Simulations (LES). The transport equation for the Favre-filtered reaction progress variable needs closure of the filtered reaction diffusion imbalance (FRDI) term (i.e. filtered value of combined reaction rate and molecular diffusion rate) and the sub-grid scalar flux (SGSF). A-priori analysis of the FRDI and SGSF terms has in the past revealed advantages and disadvantages of the specific modelling attempts. However, it is important to understand the interaction of the FRDI and SGSF closures for a successful implementation of the FSD based closure. Furthermore, it is not known a-priori if the combination of the best SGSF model with the best FRDI model results in the most suitable overall modelling strategy. In order to address this question, a variety of SGSF models is analysed in this work together with one well established and one recent FRDI closure based on a-priori analysis. It is found that the success of the combined FRDI and SGSF closures depends on subtle details like the co-variances of the FRDI and SGSF terms. It is demonstrated that the gradient hypothesis model is not very successful in representing the SGSF term. However the gradient hypothesis provides satisfactory performance in combination of a recently proposed FRDI closure, whereas unsatisfactory results are obtained when used in combination with another existing closure, which was shown to predict the FRDI term satisfactorily in several previous analyses.     

Low Reynolds number effects in open-channel turbulent boundary layers

The present study reports measurements of a turbulent boundary layer in an open-channel flow using fiber-optic laser Doppler anemometry. The Reynolds numbers based on momentum thickness and depth of flow are in the range 750≤Re _θ ≤2,400 and 15,300≤Re _h ≤54,200, respectively. It is shown that an accurate estimate of the wall shear stress can be made by fitting a fifth-order polynomial to the near-wall data. The effect of Reynolds number on the mean turbulence intensity and triple correlation is examined using both conventional scaling laws and the recent scaling laws proposed by George and Castillo. The present results show that different scaling laws lead to different conclusions on low Reynolds number effects.     

Testing an Improved Artificial Viscosity Advection Scheme to Minimise Wiggles in Large Eddy Simulation of Buoyant Jet in Crossflow

Obtaining accurate and wiggle free Large Eddy Simulation (LES) results of high Re configurations with obstacles is a challenge, especially when the resolution is moderate. This study focusses on LES of buoyant jet in crossflow (JICF). The zone in front of the jet is sensitive for wiggle formation because the jet acts as an obstacle. Only 10 grid cells over the diameter of the jet at outflow are used in order to be able to simulate very large mixing areas with limited CPU power. The resolution increases rapidly to 30–50 cells over the diameter of the bend over jet further downstream. This study tests an artificial viscosity advection scheme with sixth order dissipation, called AV6, which dissipates wiggles adequately with almost no dissipation on physical relevant scales. This desirable behaviour is demonstrated by a Fourier analysis of the Advection-Diffusion equation and turbulent flow simulations. AV6 is a mix of, and improvement over, the artificial viscosity scheme of Jameson et al. (1981) with fourth order dissipation, here called AV4, and a fifth order upwind scheme (UPW5) of Wicker and Skamarock (Mon Weather Rev 130:2088, 2002). AV6 is a robust, simple and easy to implement advection scheme and the total computational time of a simulation with AV6 is only a few percent more than with the second order central scheme (CDS2). Three realistic turbulent flow problems, relevant for buoyant JICF, are used to compare the performance of AV6 with CDS2, AV4 and UPW5 with each other and with experiments. Different grid resolutions and sub-grid scale models are used. The three test cases are a non-buoyant JICF, a buoyant jet in weak coflow, and a buoyant JICF. Of all tested advection schemes, AV6 produces best results and is preferred for LES of buoyant JICF.     

Numerical Analysis of the Impact of the Interior Nozzle Geometry on Low Mach Number Jet Acoustics

The flow and acoustic fields of subsonic turbulent hot jets exhausting from three divergent nozzles at a Mach number M=0.12 based on the nozzle exit velocity are conducted using a hybrid CFD-CAA method. The flow field is computed by highly resolved large-eddy simulations (LES) and the acoustic field is computed by solving the acoustic perturbation equations (APE) whose acoustic source terms are determined by the LES. The LES of the computational domain includes the interior of the nozzle geometry. Synthetic turbulence is prescribed at the inlet of the nozzle to mimic the exit conditions downstream of the last turbine stage. The LES is based on hierarchically refined Cartesian meshes, where the nozzle wall boundaries are resolved by a conservative cut-cell method. The APE solution is determined on a block structured mesh. Three nozzle geometries of increasing complexity are considered, i.e., the flow and acoustic fields of a clean geometry without any built-in components, a nozzle with a centerbody, and a nozzle with a centerbody plus struts are computed. Spectral distributions of the LES based turbulent fluctuated quantities inside the nozzle and further downstream are analyzed in detail. The noise sources in the near field are noticeably influenced by the nozzle built-in components. The centerbody nozzle increases the overall sound pressure level (OASPL) in the near field with respect to the clean nozzle and the centerbody-plus-strut nozzle reduces it compared to the centerbody nozzle due to the increased turbulent mixing. The centerbody perturbed nozzle configurations generate a remarkable spectral peak at S t=0.56 which also occurs in the APE findings in the near field region. This tone is generated by large scale vortical structures shed from the centerbody. The analysis of the individual noise sources shows that the entropy term possesses the highest acoustic contribution in the sideline direction whereas the vortex sound source dominates the downstream acoustics.