Effect of measuring volume length on two-component laser velocimeter measurements in a turbulent boundary layer

The effects of finite measuring volume length on laser velocimetry measurements of turbulent boundary layers were studied. Four different effective measuring volume lengths, ranging in spanwise extent from 7 to 44 viscous units, were used in a low Reynolds number (Re=1440) turbulent boundary layer with high data density. Reynolds shear stress profiles in the near-wall region show that u v strongly depends on the measuring volume length; at a given y-position, u v decreases with increasing measuring volume length. This dependence was attributed to simultaneous validations on the U and V channels of Doppler bursts coming from different particles within the measuring volume. Moments of the streamwise velocity showed a slight dependence on measuring volume length, indicating that spatial averaging effects well known for hot-films and hot-wires can occur in laser velocimetry measurements when the data density is high.List of symbols time-averaged quantity - u wall friction velocity, ( _w /)^1/2 - v kinematic viscosity - d _p pinhole diameter - l _eff spanwise extent of LDV measuring volume viewed by photomultiplier - l ⁺ non-dimensional length of measuring volume, l _eff u /v - y ⁺ non-dimensional coordinate in spanwise direction, y u /v - z ⁺ non-dimensional coordinate in spanwise direction, z u /v - U ⁺ non-dimensional mean velocity, /u - u instantaneous streamwise velocity fluctuation, U &#x2329;U - v instantaneous normal velocity fluctuation, V–V - u RMS streamwise velocity fluctuation, u ^21/2 - v RMS normal velocity fluctuation, v ^21/2 - Re Reynolds number based on momentum thickness, U 0/v - R _uv cross-correlation coefficient, u v/u v - R₁₂(0, 0, z) two point correlation between u and v with z-separation, <u(0, 0, 0) v (0, 0, z)>/<u(0, 0, 0) v (0, 0, 0)> - N rate at which bursts are validated by counter processor - T Taylor time microscale, u (dv/dt²)^–1/2     

Flow in porous media III: Deformable media

Stokes flow in a deformable medium is considered in terms of an isotropic, linearly elastic solid matrix. The analysis is restricted to steady forms of the momentum equations and small deformation of the solid phase. Darcy's law can be used to determine the motion of the fluid phase; however, the determination of the Darcy's law permeability tensor represents part of the closure problem in which the position of the fluid-solid interface must be determined.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A ^* interfacial area of the- interface contained within a unit cell, m² - A _e ^* area of entrances and exits for the-phase contained within a unit cell, m² - E Young's modulus for the-phase, N/m² - e i unit base vectors (i = 1, 2, 3) - g gravity vector, m²/s - H height of elastic, porous bed, m - k unit base vector (=e ₃) - characteristic length scale for the-phase, m - L characteristic length scale for volume-averaged quantities, m - n unit normal vector pointing from the-phase toward the-phase (n = -n ) - p pressure in the-phase, N/m² - P p – g·r, N/m² - r ₀ radius of the averaging volume, m - r position vector, m - t time, s - T total stress tensor in the-phase, N/m² - T ⁰ hydrostatic stress tensor for the-phase, N/m² - u displacement vector for the-phase, m - V averaging volume, m₃ - V volume of the-phase contained within the averaging volume, m³ - v velocity vector for the-phase, m/s Greek Letters V /V, volume fraction of the-phase - mass density of the-phase, kg/m³ - shear coefficient of viscosity for the-phase, Nt/m² - first Lamé coefficient for the-phase, N/m² - second Lamé coefficient for the-phase, N/m² - bulk coefficient of viscosity for the-phase, Nt/m² - T –T ⁰ , a deviatoric stress tensor for the-phase, N/m²     

Lp-estimates for the nonlinear spatially homogeneous Boltzmann equation

This paper studies L^p-estimates for solutions of the nonlinear, spatially homogeneous Boltzmann equation. The molecular forces considered include inverse k^th-power forces with k > 5 and angular cut-off.The main conclusions are the following. Let f be the unique solution of the Boltzmann equation with f(v,t)(1 + ¦v²¦)^(s ₁ ^{+ /p)/2} L¹, when the initial value f ₀ satisfies f ₀(v) 0, f ₀(v) (1 + ¦v¦²)^(s ₁ ^{+ /p)/2} L¹, for some s₁ 2 + /p, and f ₀(v) (1 + ¦v¦²)^s/2 L^p. If s 2/p and 1 < p < , then f(v, t)(1 + ¦v¦²)^{(s s} ₁)^/2 L^p, t > 0. If s >2 and 3/(1+ ) < p < , thenf(v,t) (1 + ¦v¦²)^(s(s ₁ ^{+ 3/p))/2} L^p, t > 0. If s >2 + 2C₀/C₁ and 3/(l + ) < p < , then f(v,t)(1 + ¦v¦²)^s/2 L^p, t > 0. Here 1/p + 1/p = 1, x y = min (x, y), and C₀, C₁, 0 < 1, are positive constants related to the molecular forces under consideration; = (k – 5)/ (k – 1) for k^th-power forces.Some weaker conclusions follow when 1 < p 3/ (1 + ).In the proofs some previously known L-estimates are extended. The results for L^p, 1 < p < , are based on these L-estimates coupled with nonlinear interpolation.     

On the closure problem for Darcy's law

In a previous derivation of Darcy's law, the closure problem was presented in terms of an integro-differential equation for a second-order tensor. In this paper, we show that the closure problem can be transformed to a set of Stokes-like equations and we compare solutions of these equations with experimental data. The computational advantages of the transformed closure problem are considerable.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the averaging volume, m² - B second-order tensor used to respresent the velocity deviation - b vector used to represent the pressure deviation, m^–1 - C second-order tensor related to the permeability tensor, m^–2 - D second-order tensor used to represent the velocity deviation, m² - d vector used to represent the pressure deviation, m - g gravity vector, m/s² - I unit tensor - K C ^–1,–D, Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the-phase, m - l _i i=1, 2, 3, lattice vectors, m - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - p pressure in the-phase, N/m ² - p intrinsic phase average pressure, N/m² - p –p , spatial deviation of the pressure in the-phase, N/m² - r position vector locating points in the-phase, m - r ₀ radius of the averaging volume, m - t time, s - v velocity vector in the-phase, m/s - v intrinsic phase average velocity in the-phase, m/s - v phase average or Darcy velocity in the \-phase, m/s - v –v , spatial deviation of the velocity in the-phase m/s - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ Greek Letters V /V volume fraction of the-phase - mass density of the-phase, kg/m³ - viscosity of the-phase, Nt/m²     

Rheology of molten polymers

Summary TheCross equation describes the flow of pseudoplastic liquids in terms of an upper and a lower Newtonian viscosity corresponding to infinite and zero shear, and ₀, and of a third material constant related to the mechanism of rupture of linkages between particles in the intermediate, non-Newtonian flow regime, Calculation of of bulk polymers is important, since it cannot be determined experimentally. The equation was applied to the melt flow data of two low density polyethylenes at three temperatures.Using data in the non-Newtonian region covering 3 decades of shear rate to extrapolate to the zero-shear viscosity resulted in errors amounting to about onethird of the measured ₀ values. The extrapolated upper Newtonian viscosity was found to be independent of temperature within the precision of the data, indicating that it has a small activation energy.The ₀ values were from 100 to 1,400 times larger than the values at the corresponding temperatures.The values of were large compared to the values found for colloidal dispersions and polymer solutions, but decreased with increasing temperature. This shows that shear is the main factor in reducing chain entanglements, but that the contribution of Brownian motion becomes greater at higher temperatures.

---

Zusammenfassung Die Gleichung vonCross beschreibt das Fließverhalten von pseudoplastischen Flüssigkeiten durch drei Konstante: Die obereNewtonsche Viskosität (bei sehr hohen Schergeschwindigkeiten), die untereNewtonsche Viskosität ₀ (bei Scherspannung Null), und eine Materialkonstante, die vom Brechen der Bindungen zwischen Partikeln im nicht-Newtonschen Fließbereich abhängt. Die Berechnung von ist wichtig für unverdünnte Polymere, wo man sie nicht messen kann.Die Gleichung wurde auf das Fließverhalten der Schmelzen von zwei handelsüblichen Hochdruckpolyäthylenen bei drei Temperaturen angewandt. Die Werte von ₀, durch Extrapolation von gemessenen scheinbaren Viskositäten im Schergeschwindigkeitsbereich von 10 bis 4000 sec^–1 errechnet, wichen bis 30% von den gemessenen ₀-Werten ab. Die Aktivierungsenergie der war so klein, daß die-Werte bei den drei Temperaturen innerhalb der Genauigkeit der Extrapolation anscheinend gleich waren. Die ₀-Werte waren 100 bis 1400 mal größer als die-Werte.Im Verhältnis zu kolloidalen Dispersionen und verdünnten Polymerlösungen war das der Schmelzen groß, nahm aber mit steigender Temperatur ab. Deshalb wird die Verhakung der Molekülketten hauptsächlich durch Scherbeanspruchung vermindert, aber der Beitrag derBrownschen Bewegung nimmt mit steigender Temperatur zu.

     

Dielectric properties of the composite system polyurethane — sodium chloride

Summary The dielectric properties of the composite system polyurethane-sodium chloride have been measured at frequencies between 10^–4 Hz and 3 · 10⁵ Hz in the temperature range from –150 °C up to +90 dgC. Three dielectric loss mechanisms have been found; they are indicated by ₁, ₂ and. The activation energy of the ₁-transition is 35 kcal/mole, that of the-transition 6.7 kcal/mole. The ₂-loss peak was only observed at frequencies of 10³ Hz and higher, forming one broad peak with the ₁-loss peak at lower frequencies. In the composite materials, the- and ₂-loss peaks measured at fixed frequencies were found at the same temperature. The ₂-loss peak, however, was shifted to a lower temperature, due to the sodium chloride filler. Comparison of experimental data of and tan with theoretical predictions concerning the dielectric properties of composite systems showed only partial agreement. The difference mainly consisted in. the temperature shift in the tan-peak of the ₁-transition.

---

Zusammenfassung Die dielektrischen Eigenschaften des Verbundssystems Kochsalz-Polyurethankautschuk wurden im Frequenzgebiet zwischen 10^–4 Hz und 3.10⁵ Hz und im Temperaturbereich von –150 °C bis +90 °C gemessen. Es wurden drei dielektrische Verlustmaxima gefunden, die mit ₁, ₂ und angedeutet werden. Die Aktivierungsenergie des ₁-Überganges beträgt 35 kcal/Mol, die des-Überganges 6.7 kcal/Mol. Das ₂-Maximum konnte nur bei Frequenzen höher als 10³Hz vom ₁-Maximum gesondert erfaßt werden. Die Lage der ₂- und-Maxima war vom Füllgrad unabhängig. Das ₁-Maximum verschiebt sich mit steigendem Füllgrad zu niedrigeren Temperaturen. Die gemessenen Werte von und tan stimmen nur teilweise mit den Aussagen einer Theorie der dielektrischen Eigenschaften von Mischkörpern überein.

     

Uniqueness and the maximum principle for quasilinear elliptic equations with quadratic growth conditions

In this paper, we show that the maximum principle holds for quasilinear elliptic equations with quadratic growth under general structure conditions.Two typical particular cases of our results are the following. On one hand, we prove that the equation (1) {ie77-01} where {ie77-02} and {ie77-03} satisfies the maximum principle for solutions in H ¹()L(), i.e., that two solutions u ₁, u ₂H¹() L() of (1) such that u ₁u₂ on , satisfy u ₁u₂ in . This implies in particular the uniqueness of the solution of (1) in H ₀ ¹ ()L().On the other hand, we prove that the equation (2) {ie77-04} where fH^–1() and g(u)>0, g(0)=0, satisfies the maximum principle for solutions uH¹() such that g(u)¦Du|{²L¹(). Again this implies the uniqueness of the solution of (2) in the class uH ₀ ¹ () with g(u)¦Du|{²L¹().In both cases, the method of proof consists in making a certain change of function u=(v) in equation (1) or (2), and in proving that the transformed equation, which is of the form (3) {ie77-05}satisfies a certain structure condition, which using ((v₁ -v ₂)⁺)ⁿ for some n>0 as a test function, allows us to prove the maximum principle.     

On natural convection from a vertical plate with a prescribed surface heat flux in porous media

This paper presents a theoretical and numerical investigation of the natural convection boundary-layer along a vertical surface, which is embedded in a porous medium, when the surface heat flux varies as (1 +x ²)), where is a constant andx is the distance along the surface. It is shown that for > -1/2 the solution develops from a similarity solution which is valid for small values ofx to one which is valid for large values ofx. However, when -1/2 no similarity solutions exist for large values ofx and it is found that there are two cases to consider, namely < -1/2 and = -1/2. The wall temperature and the velocity at large distances along the plate are determined for a range of values of .Notation g Gravitational acceleration - k Thermal conductivity of the saturated porous medium - K Permeability of the porous medium - l Typical streamwise length - q _w Uniform heat flux on the wall - Ra Rayleigh number, =gK(q _w /k)l/(v) - T Temperature - Too Temperature far from the plate - u, v Components of seepage velocity in the x and y directions - x, y Cartesian coordinates - Thermal diffusivity of the fluid saturated porous medium - The coefficient of thermal expansion - An undetermined constant - Porosity of the porous medium - Similarity variable, =y(1+x ) ^/3/x ^1/3 - A preassigned constant - Kinematic viscosity - Nondimensional temperature, =(T – T )Ra^1/3 k/qw - Similarity variable, = =y(log_e x)^1/3/x ^2/3 - Similarity variable, =y/x ^2/3 - Stream function     

Shear softening and thixotropic properties of wheat flour doughs in dynamic testing at high shear strain

Shear softening and thixotropic properties of wheat flour doughs are demonstrated in dynamic testing with a constant stress rheometer. This behaviour appears beyond the strictly linear domain (strain amplitude ₀ 0.2%),G,G and |^*| decreasing with ₀, the strain response to a sine stress wave yet retaining a sinusoidal shape. It is also shown thatG recovers progressively in function of rest time. In this domain, as well as in the strictly linear domain, the Cox-Merz rule did not apply but() and | ^*())| may be superimposed by using a shift factor, its value decreasing in the former domain when ₀ increases. Beyond a strain amplitude of about 10–20%, the strain response is progressively distorted and the shear softening effects become irreversible following rest.     

On the effects of a periodic, spanwise variation of suction upon asymptotic suction flow

Summary The effects of superposing streamwise vorticity, periodic in the lateral direction, upon two-dimensional asymptotic suction flow are analyzed. Such vorticity, generated by prescribing a spanwise variation in the suction velocity, is known to play an important role in unstable and turbulent boundary layers. The flow induced by the variation has been obtained for a freestream velocity which (i) is steady, (ii) oscillates periodically in time, (iii) changes impulsively from rest. For the oscillatory case it is shown that a frequency can exist which maximizes the induced, unsteady wall shear stress for a given spanwise period. For steady flow the heat transfer to, or from a wall at constant temperature has also been computed.Nomenclature (x, y, z) spatial coordinates - (u, v, w) corresponding components of velocity - (, , ) corresponding components of vorticity - t time - stream function for v and w - v _w mean wall suction velocity - nondimensional amplitude of variation in wall suction velocity - characteristic wavenumber for variation in direction of z - T temperature - P pressure - density - coefficient of kinematic viscosity - coefficient of thermal diffusivity - (/v _w)² - frequency of oscillation of freestream velocity - nondimensional amplitude of freestream oscillation - /v _w ² - z z - y –v _w y/ - v _w ² t/4 - /v _w - U ₀ characteristic freestream velocity - u/U ₀ - coefficient of viscosity - _w wall shear stress - Prandtl number (/) - q heat transfer to wall - T _w wall temperature - T (T _w–T)/(T _w–)     

Rheological properties of polyethylene oxide solutions

Summary Measurements were made on solutions of Polyethylene oxide (WSR-301) varying in concentration from .0511 g/dl to 4.014 g/dl, prepared from two samples of dry material of different ages (I, II), using aWeissenberg Rheogoniometer with cone-and-plate and parallel-plate geometries, and also using capillary viscometers. Steady shear data were obtained for eight decades of strain-rates (10^–3 <k < 10⁵ sec^–1), and oscillatory data for over four decades of frequency (10^–3 <f < 10¹ Hz). Results are presented for the shear-dependent viscosity,(k), normal stress differences, ₁(k), ₂(k), and the complex viscosity, ^*(f). It was found that characteristic fluid times obtained from continuum arguments correlated the experimental(k), (f) andG(f) data.Using the ^*(f) data, the stress relaxation function,(), was calculated, from which the second-order fluid coefficients and ₀ were obtained, and compared to the directly measured values.Evidence is given to show that the sign of ₁(k) varies both with concentration and strainrate.Using solutions prepared from sample II, correlations with the material properties of solutions of sample I were found which indicated the effect of aging on stored dry samples.

---

Zusammenfassung Es wurden Viskositätsmessungen an Polyäthylenoxid-(WSR-301)-Lösungen mit Konzentrationen zwischen 0,0511 g/dl und 4,014 g/dl ausgeführt, die aus zwei Proben von Trockenmaterial verschiedenen Alters (I, II) genommen waren. Verwendet wurde einWeissenberg-Rheogoniometer mit Kegel-Platte- und Parallel-Platten-Geometrie sowie verschiedene Kapillarviskosimeter. Werte für die stationäre Scherung wurden über acht Dekaden der Schergeschwindigkeit (10^–3 <k < 10⁵ s^–1) erhalten, solche für periodische Beanspruchung über mehr als vier Dekaden der Frequenz (10^–3 <f < 10 Hz). Es werden die Werte der Scherviskosität(k), der Normalspannungsdifferenzen ₁(k) und ₂(k) sowie der komplexen Viskosität ^*(f) mitgeteilt. Man findet, daß die experimentell ermittelten Werte von(k), (f) undG(f) mit Hilfe charakteristischer Zeitkonstanten, die man aus kontinuumsmechanischen Überlegungen gewinnt, korreliert werden können.Aus dem Verlauf von ^*(f) wurde die Spannungsrelaxationsfunktion() berechnet, woraus sich die Koeffizienten zweiter Ordnung und ₀ bestimmen lassen. Diese wurden mit den auf direkte Weise gewonnenen Werten verglichen. Es wird nachgewiesen, daß das Vorzeichen von ₁(k) sowohl bei der Veränderung der Konzentration als auch der Deformationsgeschwindigkeit wechselt.Durch Vergleich der an den Proben I und II erhaltenen Ergebnisse wird auf Alterungserscheinungen bei der trocken gelagerten Probe geschlossen.

---

---

With 19 figures and 1 table     

Deformation to breaking of deep water gravity waves

The results of laboratory observations of the deformation of deep water gravity waves leading to wave breaking are reported. The specially developed visualization technique which was used is described. A preliminary analysis of the results has led to similar conclusions than recently developed theories. As a main fact, the observed wave breaking appears as the result of, first, a modulational instability which causes the local wave steepness to approach a maximum and, second, a rapidly growing instability leading directly to the breaking.List of symbols L total wave length - H total wave height - crest elevation above still water level - trough depression below still water level - wave steepness =H/L - crest steepness =/L - trough steepness =/L - F ₁ forward horizontal length from zero-upcross point (A) to wave crest - F ₂ backward horizontal length from wave crest to zero-downcross point (B) - crest front steepness =/F ₁ - crest rear steepness =/F ₂ - vertical asymmetry factor=F ₂/F ₁ (describing the wave asymmetry with respect to a vertical axis through the wave crest) - µ horizontal asymmetry factor=/H (describing the wave asymmetry with respect to a horizontal axis: SWL) - T ₀ wavemaker period - L ₀ theoretical wave length of a small amplitude sinusoïdal wave generated at T _inf0 ^sup–1 frequency - ₀ average wave height     

Flow in porous media I: A theoretical derivation of Darcy's law

Stokes flow through a rigid porous medium is analyzed in terms of the method of volume averaging. The traditional averaging procedure leads to an equation of motion and a continuity equation expressed in terms of the volume-averaged pressure and velocity. The equation of motion contains integrals involving spatial deviations of the pressure and velocity, the Brinkman correction, and other lower-order terms. The analysis clearly indicates why the Brinkman correction should not be used to accommodate ano slip condition at an interface between a porous medium and a bounding solid surface.The presence of spatial deviations of the pressure and velocity in the volume-averaged equations of motion gives rise to aclosure problem, and representations for the spatial deviations are derived that lead to Darcy's law. The theoretical development is not restricted to either homogeneous or spatially periodic porous media; however, the problem ofabrupt changes in the structure of a porous medium is not considered.Roman Letters A interfacial area of the - interface contained within the macroscopic system, m² - A _e area of entrances and exits for the -phase contained within the macroscopic system, m² - A interfacial area of the - interface contained within the averaging volume, m² - A ^* interfacial area of the - interface contained within a unit cell, m² - Ae area of entrances and exits for the -phase contained within a unit cell, m² - B second order tensor used to represent the velocity deviation (see Equation (3.30)) - b vector used to represent the pressure deviation (see Equation (3.31)), m^–1 - d distance between two points at which the pressure is measured, m - g gravity vector, m/s² - K Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the -phase (see Figure 2), m - characteristic length scale for the -phase (see Figure 2), m - n unit normal vector pointing from the -phase toward the -phase (n =–n ) - n _e unit normal vector for the entrances and exits of the -phase contained within a unit cell - p pressure in the -phase, N/m² - p intrinsic phase average pressure for the -phase, N/m² - p –p , spatial deviation of the pressure in the -phase, N/m² - r ₀ radius of the averaging volume and radius of a capillary tube, m - v velocity vector for the -phase, m/s - v phase average velocity vector for the -phase, m/s - v intrinsic phase average velocity vector for the -phase, m/s - v –v , spatial deviation of the velocity vector for the -phase, m/s - V averaging volume, m³ - V volume of the -phase contained within the averaging volume, m³ Greek Letters V/V, volume fraction of the -phase - mass density of the -phase, kg/m³ - viscosity of the -phase, Nt/m² - arbitrary function used in the representation of the velocity deviation (see Equations (3.11) and (B1)), m/s - arbitrary function used in the representation of the pressure deviation (see Equations (3.12) and (B2)), s^–1     

Optical co-ordinates in general relativity 2 — the problem of distance

Summary Let denote the congruence of null geodesics associated with a given optical observer inV ₄. We prove that determines a unique collection of vector fieldsM₍₎ ( =1, 2, 3) and ₍₀₎ overV ₄, satisfying a weak version of Killing's conditions.This allows a natural interpretation of these fields as the infinitesimal generators of spatial rotations and temporal translation relative to the given observer. We prove also that the definition of the fieldsM₍₎ and ₍₀₎ is mathematically equivalent to the choice of a distinguished affine parameter f along the curves of, playing the role of a retarded distance from the observer.The relation between f and other possible definitions of distance is discussed.

---

Sommario Sia la congruenza di geodetiche nulle associata ad un osservatore ottico assegnato nello spazio-tempoV ₄. Dimostriamo che determina un'unica collezione di campi vettorialiM₍₎ ( =1, 2, 3) e ₍₀₎ inV ₄ che soddisfano una versione in forma debole delle equazioni di Killing. Ciò suggerisce una naturale interpretazione di questi campi come generatori infinitesimi di rotazioni spaziali e traslazioni temporali relative all'osservatore assegnato. Dimostriamo anche che la definizione dei campiM₍₎, ₍₀₎ è matematicamente equivalente alla scelta di un parametro affine privilegiato f lungo le curve di, che gioca il ruolo di distanza ritardata dall'osservatore. Successivamente si esaminano i legami tra f ed altre possibili definizioni di distanza in grande.

---

---

Work performed in the sphere of activity of: Gruppo Nazionale per la Fisica Matematica del CNR.     

On shock layer method for the hypersonic flow problems

Chernyi’s series method[1] is not proper for the case that(γ-l)/(γ+l)<<2/(γ+1)×M²sin²β (γ=c_p/c_v-adiabatic index number, M-Much number, β-shock incidence). In this paper, we only suppose that in the neighbour of the shock, there exists a shock layer in which the density of the gas is very big, but we do not remove the case that (γ-1)/(γ+1)<<2/(γ+1)M²sin²β.     

Similar solutions and the asymptotics of filtration equations

In this paper we consider the asymptotic behavior of solutions of the quasilinear equation of filtration as t. We prove that similar solutions of the equation u _t = (u )_xx asymptotically represent solutions of the Cauchy problem for the full equation u _t = [(u)]_xx if (u) is close to u for small u.     

Transport in ordered and disordered porous media III: Closure and comparison between theory and experiment

In this paper we examine the closure problem associated with the volume averaged form of the Stokes equations presented in Part II. For both ordered and disordered porous media, we make use of a spatially periodic model of a porous medium. Under these circumstances the closure problem, in terms of theclosure variables, is independent of the weighting functions used in the spatial smoothing process. Comparison between theory and experiment suggests that the geometrical characteristics of the unit cell dominate the calculated value of the Darcy's law permeability tensor, whereas the periodic conditions required for thelocal form of the closure problem play only a minor role.Roman Letters A interfacial area of the- interface contained within the macroscopic region, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface associated with the local closure problem, m² - A _p surface area of a particle, m² - b vector used to represent the pressure deviation, m^–1 - B ⁰ B+I, a second order tensor that maps v _m ontov - B second-order tensor used to represent the velocity deviation - d _p 6V _p/A_p, effective particle diameter, m - d a vector related to the pressure, m - D a second-order tensor related to the velocity, m² - g gravity vector, m/s² - I unit tensor - K traditional Darcy's law permeability tensor calculated on the basis of a spatially periodic model, m² - K _m permeability tensor for the weighted average form of Darcy's law, m² - L general characteristic length for volume averaged quantities, m - L _p characteristic length for the volume averaged pressure, m - L characteristic length for the porosity, m - L _v characteristic length for the volume averaged velocity, m - characteristic length (pore scale) for the-phase - _i i=1, 2, 3 lattice vectors, m - weighting function - m(-y) , convolution product weighting function - m _v special convolution product weighting function associated with the traditional averaging volume - m _g general convolution product weighting function - m _V unit cell convolution product weighting function - m _C special convolution product weighting function for ordered media which produces the cellular average - n unit normal vector pointing from the-phase toward the -phase - p pressure in the-phase, N/m² - p _m superficial weighted average pressure, N/m² - p _m intrinsic weighted average pressure, N/m² - p traditional intrinsic volume averaged pressure, N/m² - p – p _m , spatial deviation pressure, N/m² - r ₀ radius of a spherical averaging volume, m - r _m support of the convolution product weighting function - r position vector, m - r position vector locating points in the-phase, m. - V averaging volume, m³ - B volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - v velocity vector in the-phase, m/s - v _m superficial weighted average velocity, m/s - v _m intrinsic weighted average velocity, m/s - v traditional superficial volume averaged velocity, m/s - v – v _m , spatial deviation velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the -phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - _m m * , weighted average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m²     

On the cross-effects of coupled macroscopic transport equations in porous media

In this paper, the derivation of macroscopic transport equations for this cases of simultaneous heat and water, chemical and water or electrical and water fluxes in porous media is presented. Based on themicro-macro passage using the method of homogenization of periodic structures, it is shown that the resulting macroscopic equations reveal zero-valued cross-coupling effects for the case of heat and water transport as well as chemical and water transport. In the case of electrical and water transport, a nonsymmetrical coupling was found.Notations b mobility - c concentration of a chemical - D rate of deformation tensor - D molecular diffusion coefficient - D _ij ^eff macroscopic (or effective) diffusion tensor - electric field - E ₀ initial electric field - k _ij molecular tensor - j, j ^*, current densities - K _ij macroscopic permeability tensor - l characteristic length of the ERV or the periodic cell - L characteristic macroscopic length - L _ijkl coupled flows coefficients - n _i unit outward vector normal to - p pressure - q _t ,q _t ⁺ , heat fluxes - q _c ,q _c ⁺ , chemical fluxes - s specific entropy or the entropy density - S entropy per unit volume - t time variable - t _ij local tensor - T absolute temperature - v _i velocity - V ₀ initial electric potential - V electric potential - x macroscopic (or slow) space variable - y microscopic (or fast) space variable - _i local vectorial field - _i local vectorial field - electric charge density on the solid surface - , bulk and shear viscosities of the fluid - _ij local tensor - _ij local tensor - _i local vector - _ij molecular conductivity tensor - _ij ^eff effective conductivity tensor - homogenization parameter - fluid density - ₀ ion-conductivity of fluid - _ij dielectric tensor - _i ¹ , _i ² , _i ³ local vectors - ⁴ local scalar - _S solid volume in the periodic cell - _L volume of pores in the periodic cell - boundary between _S and _L - ^s rate of entropy production per unit volume - total volume of the periodic cell - _l volume of pores in the cell On leave from the Politechnika Gdanska; ul. Majakowskiego 11/12, 80-952, Gdask, Poland.     

The value of the critical exponent for reaction-diffusion equations in cones

Let D R ^N be a cone with vertex at the origin i.e., D = (0, )x where S ^N–1 and x D if and only if x = (r, ) with r=¦x¦, . We consider the initial boundary value problem: u _t = u+u ^p in D×(0, T), u=0 on Dx(0, T) with u(x, 0)=u ₀(x) 0. Let ₁ denote the smallest Dirichlet eigenvalue for the Laplace-Beltrami operator on and let ₊ denote the positive root of (+N–2) = ₁. Let p ^* = 1 + 2/(N + ₊). If 1 < p < p ^*, no positive global solution exists. If p>p ^*, positive global solutions do exist. Extensions are given to the same problem for u _t=+¦x¦ u ^p .This research was supported in part by the Air Force Office of Scientific Research under Grant # AFOSR 88-0031 and in part by NSF Grant DMS-8 822 788. The United States Government is authorized to reproduce and distribute reprints for governmental purposes not withstanding any copyright notation therein.     

Transport in ordered and disordered porous media IV: Computer generated porous media for three-dimensional systems

In the method of volume averaging, the difference between ordered and disordered porous media appears at two distinct points in the analysis, i.e. in the process of spatial smoothing and in the closure problem. In theclosure problem, the use of spatially periodic boundary conditions isconsistent with ordered porous media and the fields under consideration when the length-scale constraint,r ₀L is satisfied. For disordered porous media, spatially periodic boundary conditions are an approximation in need of further study.In theprocess of spatial smoothing, average quantities must be removed from area and volume integrals in order to extractlocal transport equations fromnonlocal equations. This leads to a series of geometrical integrals that need to be evaluated. In Part II we indicated that these integrals were constants for ordered porous media provided that the weighting function used in the averaging process contained thecellular average. We also indicated that these integrals were constrained by certain order of magnitude estimates for disordered porous media. In this paper we verify these characteristics of the geometrical integrals, and we examine their values for pseudo-periodic and uniformly random systems through the use of computer generated porous media.

Nomenclature

Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - a _i i=1, 2, 3 gaussian probability distribution used to locate the position of particles - I unit tensor - L general characteristic length for volume averaged quantities, m - L characteristic length for , m - L characteristic length for , m - characteristic length for the -phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1, 2, 3 lattice vectors, m - m convolution product weighting function - m _v special convolution product weighting function associated with the traditional volume average - n _i i=1, 2, 3 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - r position vector, m - r _m support of the weighting functionm, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume,, m³ - x positional vector locating the centroid of an averaging volume, m - x ₀ reference position vector associated with the centroid of an averaging volume, m - y position vector locating points relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - /L, small parameter in the method of spatial homogenization - standard deviation ofa _i - _r standard deviation ofr - _r intrinsic phase average of