A rapid and selective LC method for simultaneous determination of cyclosporin a and its major metabolite (AM1) in human serum at room temperature

A simple and highly selective isocratic reverse-phase high performance liquid chromatography (RP-LC) method at room temperature is developed in order to determination of Cyclosporine A (CyA) and its major metabolite (AM1) in serum samples of kidney transplanted patients. The method uses a phenyl column stationary phase, acetonitrile–water–methanol 47:50:3 as mobile phase and 215 nm detector wavelength, at room temperature. The solid phase extraction procedure using cyano disposable extraction column was carried out to separtate the CyA and AM1 with recovery 99±6 and 98±10, respectively. A linear correlation was found at the range of 40–1000 ng ml⁻¹ for CyA and 25–500 ng ml⁻¹ for AM1. The average intra and inter-day variations were 5.03 and 7.89% for CyA, 5.92 and 8.12% for AM1, respectively. The detection limit of 20 ng ml⁻¹ was found for CyA and 12.5 ng ml⁻¹ for AM1. Also, the clinical application of the method using serum concentration against time profile from kidney transplantated patients is reported.     

Catalytic flow injection determination of vanadium by oxidation of N-(3-sulfopropyl)-3,3',5,5'-tetramethylbenzidine using bromate

A catalytic flow-injection (FI) method was developed for the determination of 10⁻⁹ mol l⁻¹ levels of vanadium(IV, V). The method is based on the catalytic effect of vanadium(V) on oxidation of N-(3-sulfopropyl)-3,3′,5,5′-tetramethylbenzidine (TMBZ·PS) using bromate as oxidant to form a yellow dye (λ_max=460 nm). The use of 5-sulfosalicylic acid (SSA) as an activator enhanced the sensitivity of the method. The calibration graphs with a working range 0.05–8.0 ng ml⁻¹ were obtained for vanadium(V). Vanadium(IV) was also determined, being oxidized by bromate. The detection limit (signal/noise, S/N=3) was 0.01 ng ml⁻¹ (ca. 2×10⁻¹⁰ mol l⁻¹) vanadium. The relative standard deviations (R.S.D.) for 15 determinations of 0.5 ng ml⁻¹ vanadium, and for ten determinations of 0.1 and 1.0 ng ml⁻¹ vanadium were 0.41, 2.6 and 0.25%, respectively, with a sampling rate of 15 samples h⁻¹. The proposed method was successfully applied to the determination of vanadium in natural waters.     

Determination of glyphosate by ion chromatography

An ion chromatography system for the determination of glyphosate was described. Ion chromatograph was carried out by suppressed conductivity detection (DX-100). The eluent contained 9 mmol l⁻¹ Na₂CO₃ and 4 mmol l⁻¹ NaOH. The detection limit was 0.042 μg ml⁻¹ (S/N=3). The relative standard deviation was 1.99% and the correlation coefficient of the calibration curve for area was 0.9995. The linear range was 0.042100 μg ml⁻¹. Common inorganic ion and organic acids did not interfere. The recovery was 96.4103.2%. The method was simple, rapid, reliable and inexpensive.     

Flow-injection chemiluminescence determination of tetracyclines with in situ electrogenerated bromine as the oxidant

By designing a novel flow-through electrolytic cell (FEC), bromine was produced near to the surface of the platinum electrode by electrochemical oxidation of acidic KBr. The fast and weak chemiluminescence signal produced by the chemical reaction of the electrogenerated bromine with H₂O₂ was greatly enhanced by tetracyclines Based on these observations, a new, sensitive and simple electrogenerated chemiluminescence (ECL) method for the determination of tetracyclines was developed. Under the optimum experimental conditions, the calibration graphs are linear over the range 3.0×10⁻⁸ to 5.0×10⁻⁵ g ml⁻¹ for tetracycline, 2.0×10⁻⁷ to 2.4×10⁻⁵ g ml⁻¹ for oxytetracycline and 1.0×10⁻⁷ to 5.0×10⁻⁵ g ml⁻¹ for chlortetracycline. The limits of detection (S/N=3) are 1.0×10⁻⁸ g ml⁻¹ for tetracycline, 7.0×10⁻⁸ g ml⁻¹ for oxytetracycline and 1.5×10⁻⁷ g ml⁻¹ for chlortetracycline. For the determination 5.0×10⁻⁷ g ml⁻¹ tetracycline, the relative standard deviation was <5%. The proposed method was used to determine tetracyclines in pharmaceutical formulations.     

Two different strategies for the fluorimetric determination of piroxicam in serum

Two different spectrofluorimetric methods for the determination of piroxicam (PX) in serum are presented and discussed. One of them is based on the use of three-way fluorescence data and multivariate calibration performed with parallel factor analysis (PARAFAC) and self-weighted alternating trilinear decomposition (SWATLD). This methodology exploits the so-called second-order advantage of the three-way data, allowing to obtain the concentration of the studied analyte in the presence of any number of uncalibrated (serum) components. The method was developed following two different procedures: internal standard addition and external calibration with standard solutions, which were compared and discussed. The second approach investigated is based on the combination of solid-phase extraction (SPE) and room temperature fluorimetry. Both methods here presented yield satisfactory results. The concentration range in which PX could be determined in serum was 1–10 μg ml⁻¹. The limits of quantification for the experimental solutions using the chemometric approach were 0.09 μg ml⁻¹ for the standard addition mode and 0.12 μg ml⁻¹ using external calibration (both for PARAFAC and SWATLD algorithms). In the solid-surface fluorimetric method, the calibration graph was linear up to 0.22 μg ml⁻¹ and the limit of quantification was 0.02 μg ml⁻¹.     

Development of a luminol-based chemiluminescence flow-injection method for the determination of dichlorvos pesticide

A simple, fast chemiluminescence (CL) flow-injection method based on the reaction of luminol with H₂O₂ in the presence of a cationic surfactant (cyltrimethylammonium bromide, CTMAB) has been described for the direct determination of dichlorvos pesticide (DDVP). Under the optimal conditions, the CL intensity was linear to the DDVP concentration in the range of 0.02–3.1 μg ml⁻¹ (r=0.9998, n=10). The relative standard deviation was 3.4% at 0.35 μg ml⁻¹ (n=10), with a detection limit (3σ) of 0.008 μg ml⁻¹ DDVP. The possible reaction mechanism was also discussed. This method has been successfully applied to the determination of trace DDVP residue in vegetable sample and results have been compared with that of the UV method.     

Flow injection chemiluminescence determination of polyhydroxy phenols using luminol-ferricyanide/ferrocyanide system

It was found that the weak chemiluminescence produced from the reaction of polyhydroxy phenols with luminol in alkaline solution could be strongly enhanced by ferricyanide and ferrocyanide. Based on this found, a new flow injection chemiluminescence method is proposed for the determination of four polyhydroxy phenols: pyrogallol, phlorglucinol, quinol and resorcinol. The detection limits of the method are 0.03 μg ml⁻¹ pyrogallol, 0.03 μg ml⁻¹ phlorglucinol, 0.04 μg ml⁻¹ quinol, and 0.02 μg ml⁻¹ resorcinol. The possible mechanism of CL reactions is also discussed briefly.     

Spectrophotometric determination of nitrate and nitrite in soil and water samples with a diazotizable aromatic amine and coupling agent using column preconcentration on naphthalene supported with ion-pair of tetradecyldimethylbenzylammonium and iodide

Composite diazotization-coupling reagents containing sulfanilamide (SAM), sulfapyridine (SP) or sulfathiazole (ST) as the diazotizable aromatic amines and sodium 1-naphthol-4-sulfonate (NS) as the coupling agent using column preconcentration on naphthalene-tetradecyldimethylbenzylammonium(TDBA)-iodide adsorbent have been used for the spectrometric determination of trace nitrate and nitrite in soil and water samples. Nitrite ion reacts with SAM in the pH range 2.0–5.0, SP in the pH range 2.0–2.5 and ST in the pH range 2.0–3.3 in HCl medium to form water-soluble colourless diazonium cations. These cations were coupled with NS in the pH range 9.0–12.0 for the SAM system, 9.6–12.0 for the SP system and 8.5–12.0 for the ST system to be retained on naphthalene-TDBA-I material packed in a column. The solid mass is dissolved from the column with 5 ml of dimethylformamide and the absorbance is measured spectrometerically at 543 nm for SAM-NS, 533 nm for SP-NS and 535 nm for ST-NS. Nitrate is reduced to nitrite by a copper-coated cadmium reductor column and the nitrite is then treated with the diazotization-coupling reagent by column preconcentration. The absorbance due to the sum of nitrate and nitrite is measured and nitrate is determined by difference. The calibration graph was linear over the range 2–40 ng NO₂⁻-N ml⁻¹ and 1.5–30 ng NO₃⁻-N ml⁻¹ in aqueous samples for the SAM and ST systems and 2–48 ng NO₂⁻-N ml⁻¹ and 1.5–36 ng NO₃⁻-N ml⁻¹ in aqueous samples for the SP system, respectively. The sensitivity, accuracy and precision of the systems decreased in the order STSAMSP. The detection limits were 1.4 ng NO₂⁻-N ml⁻¹ and 1.1 ng NO₃⁻-N ml⁻¹ for SAM, 1.6 ng NO₂⁻-N ml⁻¹ and 1.2 ng NO₃⁻-N ml⁻¹ for SP, and 1.0 ng NO₂⁻-N ml⁻¹ and 0.75 ng NO₃⁻-N ml⁻¹ for ST, respectively. The preconcentration factors are 8, 5 and 6 for SAM-NS, SP-NS and ST-NS, respectively. Interferences from various foreign ions have been studied and the methods have been applied to the determination of ng ml⁻¹ levels of nitrite and nitrate in soil and water samples. The mean recovery was 95–102% for all three systems.     

Flow-injection chemiluminescence determination of chlortetracycline using on-line electrogenerated [Cu(HIO(6))(2)](5-) as the oxidant

A novel chemiluminescence (CL) flow system for the determination of chlortetracycline is described. It is based on the direct CL reaction of chlortetracycline and [Cu(HIO₆)₂]⁵⁻ in KOH medium. The unstable [Cu(HIO₆)₂]⁵⁻ was on-line electrogenerated by constant-current electrolysis. The CL intensity was linear with chlortetracycline concentration in the range of 0.1–100 μg ml⁻¹. The determination limit was 5.3×10⁻⁸ g ml⁻¹. The whole process could be completed in 1 min. The proposed method is suitable for automatic and continuous analysis, and has been applied satisfactorily to analysis of chlortetracycline in biological fluid.     

Ion chromatographic determination of traces of some oxoanions with direct spectrophotometric detection

Investigation of the use of a single analytical procedure using the non-suppressed ion chromatographic method with direct spectrophotometric detection capable of determining eight oxoanions simultaneously is presented in this paper. Potassium phosphate was found to be the most suitable eluent for UV absorbance detection at 205 nm. Oxoanions AsO³⁻₃, SeO²⁻₃, AsO³⁻₄, VO⁻₃, SeO²⁻₄, WO²⁻₄, MoO²⁻₄ and CrO²⁻₄ were detected at ng ml⁻¹ levels with well separated peaks at retention time < 25 min. The working range is in the range ng ml⁻¹ to 50 μg ml⁻¹. The method is sufficiently sensitive to determine As (V), V(V), Mo(VI) and Cr(VI) anions (and NO⁻₃) directly in a river water sample. The accuracy of these results was established by comparison with conventional atomic absorption methods.     

Spectrophotometric method for determination of vanadium and its application to industrial, environmental, biological and soil samples

The very sensitive, fairly selective direct spectrophotometric method for the determination of trace amount of vanadium (V) with 1,5-diphenylcarbohydrazide (1,5-diphenylcarbazide) has been developed. 1,5-diphenylcarbohydrazide (DPCH) reacts in slightly acidic (0.0001–0.001 M H₂SO₄ or pH 4.0–5.5) 50% acetonic media with vanadium (V) to give a red–violet chelate which has an absorption maximum at 531 nm. The average molar absorption coefficient and Sandell’s sensitivity were found to be 4.23×10⁴ l mol⁻¹ cm⁻¹ and 10 ng cm⁻² of V^v, respectively. Linear calibration graph were obtained for 0.1–30 μg ml⁻¹ of V^v: the stoichiometric composition of the chelate is 1:3 (V: DPCH). The reaction is instantaneous and absorbance remain stable for 48 h. The interference from over 50 cations, anions and complexing agents has been studied at 1 μg ml⁻¹ of V^v. The method was successfully used in the determination of vanadium in several standard reference materials (alloys and steels), environmental waters (potable and polluted), biological samples (human blood and urine), soil samples, solution containing both vanadium (V) and vanadium (IV) and complex synthetic mixtures. The method has high precision and accuracy (s=±0.01 for 0.5 μg ml⁻¹).     

Reverse flow injection spectrophotometric determination of iron(III) using chlortetracycline reagent

A simple reversed flow injection colourimetric procedure for determining iron(III) was proposed. It is based on the reaction between iron(III) with chlortetracycline, resulting in an intense yellow complex with a suitable absorption at 435 nm. A 200 μl chlortetracycline reagent solution was injected into the phosphate buffer stream (flow rate 2.0 ml min⁻¹) which was then merged with iron(III) standard or sample in dilute nitric acid stream (flow rate 1.5 ml min⁻¹). Optimum conditions for determining iron(III) were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.5–20.0 μg ml⁻¹. The detection limit (3σ) and the quantification limit (10σ) were 0.10 and 0.82 μg ml⁻¹, respectively. The relatives standard deviation of the proposed method calculated from 12 replicate injections of 2.0 and 10.0 μg ml⁻¹ iron(III) were 0.43 and 0.59%, respectively. The sample throughput was 60 h⁻¹. The proposed method has been satisfactorily applied to the determination of iron(III) in natural waters.     

Simple spectrophotometric determination of tinidazole in formulation and serum

A simple and rapid spectrophotometric method for the determination of tinidazole is presented. This method is based on the measurement of the absorbance of the signal at 368 nm yielded by bathochromic shift during alkaline hydrolysis of tinidazole in 0.1 N NaOH. The method is linear within the range of 1–30 μg ml⁻¹, and the detection and quantification limits are 0.07 and 0.25 μg ml⁻¹, respectively. The precision of the method, expressed as the relative standard deviation, is 0.19% for a tinidazole concentration of 15 (μg ml⁻¹. The method was applied to the analysis of tinidazole in pharmaceutical formulations and serum.     

Chemiluminescent determination of pyridoxine hydrochloride in pharmaceutical samples using flow injection

A chemiluminescent method using flow injection is described for the determination of pyridoxine hydrochloride. Its detection limit, linearity and reproducibility were examined. The method is based on the enhancing effect of pyridoxine hydrochloride on the chemiluminescence generated by the oxidation of luminol with hydrogen peroxide in aqueous potassium hydroxide and sodium oxalate. The proposed method is simple and inexpensive. The chemiluminescence intensity is a linear function of pyridoxine hydrochloride concentration over the range 10–250 μg ml⁻¹ with a detection limit of 6 μg ml⁻¹. The applicability of the method was demonstrated by the determination of pyridoxine hydrochloride in different tablet formulations and some dietary sources.     

Development and application of a capillary electrophoresis-electrochemiluminescent method for the analysis of enrofloxacin and its metabolite ciprofloxacin in milk

Enrofloxacin (ENR) is a fluoroquinolone developed exclusively for the use in veterinary practice for the treatment of respiratory and gastrointestinal infections, and ciprofloxacin (CIP) is its main active metabolite. Their contents are regulated by the EU Council Regulation no. 2377/90 in animal edible tissues. We developed a sensitive and rapid method for the determination of ENR and CIP by capillary electrophoresis (CE) with electrochemiluminescence (ECL) detection. The method is based on the detection of aliphatic tertiary or secondary amino moieties in ENR and CIP with end-column tris(2,2-bipyridyl)ruthenium(II) electrochemiluminescence. Parameters that affect separation and detection were optimized. Under the optimized conditions, the calibration functions were linear in the range of 0.03–1 μg ml⁻¹ for ENR and 0.05–1.2 μg ml⁻¹ for CIP. The detection limits of ENR and CIR were 10 ng ml⁻¹ and 15 ng ml⁻¹, respectively, based on the signal-to-noise ratio of 3. The relative standard derivations of the peak height and the migration time for ENR and CIP were less than 4.13%. The developed method was successfully applied to determine ENR and CIP in milk with a solid-phase extraction procedure.     

Spectrophotometric determination of nitrite based on its catalytic effect on the oxidation of carminic acid by bromate

A highly sensitive and selective method is described for the determination of trace amounts of nitrite based on its effect on the oxidation of carminic acid with bromate. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of carminic acid at 490 nm after 3 min of mixing the reagents. The optimum reaction conditions were 1.8×10⁻¹ mol l⁻¹ H₂SO₄, 3.8×10⁻³ mol l⁻¹ KBrO₃, and 1.2×10⁻⁴ mol l⁻¹ carminic acid at 30°C. By using the recommended procedure, the calibration graph was linear from 0.2 to 14 ng ml⁻¹ of nitrite; the detection limit was 0.04 ng ml⁻¹; the R.S.D. for six replicate determinations of 6 ng ml⁻¹ was 1.7%. The method is mostly free from interference, especially from large amounts of nitrate and ammonium ions. The proposed method was applied to the determination of nitrite in rain and river water.     

Reverse flow injection spectrophotometric determination of iron(III) using norfloxacin

A reversed flow injection colorimetric procedure for determining iron(III) at the μg level was proposed. It is based on the reaction between iron(III) with norfloxacin (NRF) in 0.07 mol l⁻¹ ammonium sulfate solution, resulting in an intense yellow complex with a suitable absorption at 435 nm. Optimum conditions for determining iron(III) were investigated by univariate method. The method involved injection of a 150 μl of 0.04% w/v colorimetric reagent solution into a merged streams of sample and/or standard solution containing iron(III) and 0.07 mol l⁻¹ ammonium sulfate in sulfuric acid (pH 3.5) solution which was then passed through a single bead string reactor. Subsequently the absorbance as peak height was monitored at 435 nm. Beer's law obeyed over the range of 0.2–1.4 μg ml⁻¹ iron(III). The method has been applied to the determination of total iron in water samples digested with HNO₃–H₂O₂ (1:9 v/v). Detection limit (3σ) was 0.01 μg ml⁻¹ the sample through of 86 h⁻¹ and the coefficient of variation of 1.77% (n=12) for 1 μg ml⁻¹ Fe(III) were achieved with the recovery of the spiked Fe(III) of 92.6–99.8%.     

Simple and rapid flow-injection spectrophotometric determination of carbaryl after liquid-liquid extraction

A simple procedure was developed for the spectrophotometric determination of carbaryl and its hydrolysis product 1-naphthol in water. These compounds are extracted into xylene and back-extracted, as the 1-naphtholate, with 0.2 M NaOH. A 600-μl volume of the alkaline extract is injected into a flow analysis manifold which provides the reaction between naphtholate and 50 μg ml⁻¹ p-aminophenol solution in the presence of 0.004 M KIO₄ and spectrophotometric measurement is carried out at 596 nm. The method provides a limit of detection of 26.5 ng ml⁻¹ carbaryl and a sample frequency of 110 injections per hour. Recoveries in different types of matrices vary from 95 to 102%.     

Turbidimetric determination of sulphate in waters employing flow injection and lead sulphate formation

An analytical flow-injection procedure based on PbSO₄ colloidal formation is proposed as a turbidimetric determination of sulphate in natural waters. Ethanol-water was used as a medium in order to improve the sensibility of the method. Both chemical and flow variables as well as interfering species were studied. A detection limit of 0.3 μg SO²⁻₄ ml⁻¹ was found, and the analytical range (according to Beer's law) was 2–20 μg SO²⁻₄ ml⁻¹. The precision was better than 3% R.S.D. and the sample throughput was ca. 35 h⁻¹. The method, when compared with a standard methodology, gave good results when applied to water analysis.     

Simultaneous determination of trace uranium(VI) and zinc(II) by adsorptive cathodic stripping voltammetry with aluminon ligand

Uranium(VI) complexed with aluminon (3-[bis(3-carboxy-4-hydroxy-phenyl)methylene]-6-oxo-1,4-cyclohexadiene-1-carboxylic acid triammonium salt) was determined by adsorptive cathodic stripping voltammetry (ACSV) using a hanging mercury drop electrode. Trace uranium(VI) and zinc(II) can be simultaneously determined in a single scan in the presence of aluminon and urea. Optimal conditions were found to be: accumulation time; 180–200 s, accumulation potential; 50 mV versus Ag/AgCl, scan rate; 40 mV s⁻¹, supporting electrolyte; 0.1 M sodium acetate buffer at pH 6.5–7.0, and concentration of aluminon; 1×10⁻⁶ M. The linear range of uranium(VI) and zinc(II) were observed over the concentration range 2–33 and 30–120 ng ml⁻¹, respectively. The detection limit (S/N=3) are 0.2 ng ml⁻¹ (uranium) and 30 ng ml⁻¹ (zinc). A good reproducibility shows RSDs of 2.5–4.0% (n=10). The procedure offers high selectivity, with the presence of urea masking some metal ions.