Multi‐walled carbon nanotubes (MWNT) purified by acidic solution were processed with PMMA via an in‐situ polymerization. Experimental evidences indicate the role of radical initiator (AIBN) and MWNT, showing increases of polymerization rate and MWNT diameter. Induced radicals on the MWNT by AIBN were found to trigger the grafting of PMMA. Moreover, the solvent cast film showed a better nanoscopic dispersion of MWNT and possibilities of CNT composites in engineering applications.
Fractured surface of multi‐walled carbon nanotube composite with PMMA prepared by in‐situ bulk polymerization. 相似文献
A simple method to fabricate polymer nanocomposites with single‐walled carbon nanotubes is reported, in which the nanotubes were reacted with poly(L ‐lysine) by using high‐speed vibration milling. The nanocomposites obtained were characterized by Fourier transform infrared (FT‐IR), UV–Vis spectroscopy, and thermogravimetric methods. The morphology as well as the dispersion of the carbon nanotubes were determined by scanning and transmission electron microscopy.
Carbon nanotubes typically require the use of a dispersing or stabilizing agent to prevent significant aggregation during incorporation into a polymer matrix. These additives must be strongly associated, either covalently or physically, to achieve their purpose. In this study, multi‐walled carbon nanotubes (MWNTs) were dispersed into an epoxy matrix using polyethylenimine (PEI) as a dispersant that was either covalently attached to the nanotubes or physically mixed to result in only noncovalent interaction. Epoxy composites containing covalently modified MWNTs exhibited greater storage modulus and reduced electrical conductivity.
A facile microwave method (MW) is described that accomplishes alignment and decoration of noble metals on carbon nanotubes (CNT) wrapped with carboxymethyl cellulose (CMC). Carbon nanotubes such as single‐ and multi‐walled, and Buckminsterfullerene (C‐60) are well dispersed using the sodium salt of CMC under sonication. Addition of respective noble metal salts then generates noble metal‐decorated CNT composites at room temperature. However, aligned nanocomposites of CNTs could only be generated by exposing the above nanocomposites to MW irradiation. The CNT composites are characterized using scanning electron microscopy, energy dispersive X‐ray analysis, X‐ray mapping, transmission electron microscopy, and UV‐visible spectroscopy. The general preparative procedure is versatile and provides a simple route to manufacturing useful metal‐coated CNT nanocomposites.
Summary: The relatively high degree of crystallinity of a new thermoplastic polyimide (PI) makes it a favorable matrix candidate for fiber reinforced composites. This advantage is the result of the ability of the matrix to recrystallize during the composite manufacturing process. In this study we examine the potential nucleating effect of carbon nanotubes on a thermoplastic PI. In addition to their inherent mechanical contribution, the carbon nanotubes help recover a significant proportion of the original crystallinity.
Scanning electron micrograph of the spherulitic structure of a recrystallized carbon nanotube/polyimide film. 相似文献
Nanoscale fibers with embedded, aligned, and percolated non‐functionalized multiwalled carbon nanotubes (MWCNTs) were fabricated through electrospinning dispersions based on melt‐compounded thermoplastic polyurethane/MWCNT nanocomposite, with up to 10 wt.‐% MWCNTs. Transmission electron microscopy indicated that the nanotubes were highly oriented and percolated throughout the fibers, even at high MWCNT concentrations. The coupling of efficient melt compounding with electrospinning eliminated the need for intensive surface functionalization or sonication of the MWCNTs, and the high aspect ratio as well as the electrical and mechanical properties of the nanotubes were retained. This method provides a more efficient technique to generate one‐dimensional nanofibers with aligned MWCNTs.
It is demonstrated that an optically transparent and electrically conductive polyethylene oxide (PEO) film is fabricated by the introduction of individualized single‐walled carbon nanotubes (SWNTs). The incorporated SWNTs in the PEO film sustain their intrinsic electronic and optical properties and, in addition, the intrinsic properties of the polymer matrix are retained. The individualized SWNTs with smaller diameter provide high transmittance as well as good electrical conductivity in PEO films.
This communication reports a strategy for scale‐up of an in situ polymerization technique for polyolefin‐based nanocomposites preparation, taking layered silicate (clay) and multi‐walled carbon nanotubes (MWCNTs) as examples of nanofillers. The strategy is realized by transforming the nanofillers into granular “nanosupports” for Ziegler‐Natta catalysts. With a catalyst to polymer replication effect on particle morphology, the in situ prepared nanocomposites are of controlled granular particle morphology. With the polymer particle morphology controlled, the in situ polymerization technique becomes suitable for industrial olefin polymerization processes for mass production of polyolefin nanocomposites.
Multiwalled carbon nanotubes (MWNTs) have been introduced into blends of polycarbonate (PC) and poly(styrene‐acrylonitrile) (SAN) by melt mixing in a microcompounder. Co‐continuous blends are prepared by either pre‐compounding low amounts of nanotubes into PC or SAN or by mixing all three components together. Interestingly, in all blends, regardless of the way of introducing the nanotubes, the MWNTs were exclusively located within the PC phase, which resulted in much lower electrical resistivities as compared to PC or SAN composites with the same MWNT content. The migration of MWNTs from the SAN phase into the PC phase during common mixing is explained by interfacial effects.
Carbon nanotube–polymer composite fibers are obtained by infiltration of a monomer liquid into aligned carbon nanotube aerogel fibers with subsequent in situ polymerization. The monomer, methyl methacrylate (MMA), was infiltrated into the aerogel fibers of multi‐walled carbon nanotubes (MWNTs) at room temperature and subsequently polymerized at 50 °C into poly(methyl methacrylate) (PMMA). Cross‐sections of the PMMA/MWNT composite fibers showed that the PMMA filled the spaces of the nanotube fibers and bound the nanotubes together. PMMA in the composite fibers exhibited local order. The resultant composite fibers with 15 wt.‐% nanotube loading exhibited a 16‐fold and a 49‐fold increase in tensile strength and Young's modulus, respectively, compared to the control PMMA.
Water‐soluble single‐ and multi‐walled carbon nanotubes (CNTs) were prepared by grafting polyacrylamide chains from the graphitic surface via ceric ion‐induced redox radical polymerization. The reducing functionalities were covalently attached to the tubes by peroxide‐assisted radical reaction. The results showed that polymer chains were grafted onto CNTs by the redox process. The redox radical polymerization initiated by carbon nanotube‐bearing functionalities not only provides a powerful strategy for modifying the carbon nanostructures but also gives us the knowledge of their sidewall chemistry.
Summary: Multiwalled carbon nanotube (MWNT) nanocomposites dispersed in a poly(methyl methacrylate) (PMMA) matrix were prepared via suspension polymerization, in which radicals induced on the outer wall of the MWNTs by 2,2′‐azoisobutyronitrile initiate the grafting of PMMA. The synthesized MWNT/PMMA nanocomposite particles were found to have a spherical shape and exhibit a high electrical conductivity, mainly as a result of the carbon nanotubes. A suspension was prepared with MWNT/PMMA particles in insulating silicone oil and its electrorheological properties were investigated by controlling applied direct current (DC) electric field strengths.
Flow curve possessing a region analogous to the coexistence curve. 相似文献
The ability to control the dispersion of carbon nanotubes in polymers is key to most applications of nanotube‐polymer composites. This feature article describes recent advances in methods used to disperse carbon nanotubes and considers how these methods affect dispersion on different length scales. It is becoming increasing clear that perfect dispersion is not desired for many applications, in particular for electrical conductivity, and controlling the dispersion is key for proper function of the composite in its intended application.
Fluorescent vesicles considered as a mimic of natural primitive cells are prepared from poly(3‐hexylthiophene)‐block‐poly(3‐O‐methacryloyl‐D‐galactopyranose) P3HT‐b‐PMAGP copolymers. The unique characteristic of such vesicular nanostructures is their architecture, which comprises a hydrophobic π‐conjugated P3HT wall stabilized by a hydrophilic PMAGP interface featuring glucose units. The results of this work offer a very efficient and straightforward method for engineering well‐controlled fluorescent nanoparticles (without the addition of dyes), which provide an excellent support to the study of carbohydrate‐protein interactions.
Summary: Electro‐active shape‐memory composites were synthesized using conducting polyurethane (PU) composites and multi‐walled carbon nanotubes (MWNTs). Surface modification of the MWNTs (by acid treatment) improved the mechanical properties of the composites. The modulus and stress at 100% elongation increased with increasing surface‐modified MWNT content, while elongation at break decreased. MWNT surface modification also resulted in a decrease in the electrical conductivity of the composites, however, as the surface modified MWNT content increased the conductivity increased (an order of 10−3 S · cm−1 was obtained in samples with 5 wt.‐% modified‐MWNT content). Electro‐active shape recovery was observed for the surface‐modified MWNT composites with an energy conversion efficiency of 10.4%. Hence, PU‐MWNT composites may prove promising candidates for use as smart actuators.
The electro‐active shape‐recovery behavior of PU‐MWNT composites. The pictured transition occurs within 10 s when a constant voltage of 40 V is applied. 相似文献
The preparation of associative networks containing multi‐walled carbon nanotubes (MWCNTs) with covalently attached cyclodextrin (CD) rings and poly[(isobutylene)‐co‐(maleic anhydride)‐co‐(maleic acid‐(4‐tert‐butylphenyl)amide)] in water is described in this study. The synthesis of CD containing MWCNTs is realized by an amidation reaction of oxidized MWCNTs with propargylamine followed by a 1,3‐dipolar cycloaddition with CD‐azide. Dispersion behavior indicated the high stability of these networks. An increase in viscosity compared to a solution of pure polymer as a cause of network formation is observed. The addition of a CD‐decomposing enzyme (taka‐diastase from Aspergillus oryzae) let the network collapse and results in sedimentation of the modified MWCNTs.
In this communication, the synthesis, characterization, and properties of highly conductive core–shell nanocomposites of poly(N‐vinylcarbazole) (PNVC)–polypyrrole (PPY) copolymers with multi‐walled carbon nanotubes (MWCNTs) are described. A unique free‐radical coupling reaction between PNVC and PPY cation radicals in chloroform solvent, using feric chloride as an oxidant, in the presence of suspended MWCNTs in the reaction medium, was used for the synthesis of nanocomposite. Field‐emission scanning and transmission electron microscopy studies showed the formation of the core–shell nanocomposite. Raman spectrocopy results as well as thermogravimetric analysis supported the electron microscopic observations. The resulting PNVC–PPY copolymer‐coated MWCNTs showed an unprecedentedly increased value of direct electrical conductivity (bulk) compared to the conductivity of all samples even with pure MWCNTs.
The cytotoxicity and cellular uptake of carbon nanotubes (CNTs) has recently attracted considerable interest because of the issue of biosphere‐nanomaterial interactions. The biocompatibility of CNTs is determined by the metal impurities in the CNTs, the size of the CNTs and the CNT dispersion states; in particular, the type of surface modifications on the CNTs affects how they interact with cells and determines their cytotoxicity and cellular uptake. In this study, biocompatible single‐walled carbon nanotubes (SWNTs) wrapped with a water‐soluble copolymer, poly[2‐(dimethylamino)ethyl methacrylate‐co‐methacrylic acid] (PDM), were prepared. We report that these SWNTs have enhanced water dispersibility and cellular internalization but no significant cytotoxic activity against mouse embryonic fibroblast NIH‐3T3 cells.
We report a facile method to accomplish the crosslinking reaction of PVA with SWNTs, MWNTs, and C‐60 using MW irradiation. Nanocomposites of PVA crosslinked with SWNT, MWNT and C‐60 were prepared expeditiously by reacting the respective carbon nanotubes with 3 wt.‐% PVA under MW irradiation, maintaining a temperature of 100 °C, representing a radical improvement over literature methods to prepare such crosslinked PVA composites. This general preparative procedure is versatile and provides a simple route to manufacture useful SWNT, MWNT and C‐60 nanocomposites.
