Highly conductive soluble terpolymers of aniline,toluidine, and o‐aminobenzoic acid/m‐aminobenzenesulfonic acid

Two series of terpolymers, one of o‐/m‐toluidine and aniline with o‐aminobenzoic acid and the other of o‐/m‐toluidine and aniline with m‐aminobenzenesulfonic acid, have been synthesized by oxidative polymerization via an emulsion method with ammonium persulfate as the oxidant and HCl as the external dopant. The terpolymers exhibit excellent solubility and retain the high conductivity (∼1 S cm⁻¹) characteristic of the unsubstituted homopolymer, polyaniline. The terpolymers also possess higher thermal stability than polyaniline. This can be attributed to the presence of internal doping groups and substituents, which introduce flexibility to the otherwise rigid polyaniline backbone. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3040–3048, 2005     

Preparation and characterization of soluble terpolymers from m‐phenylenediamine,o‐anisidine,and 2,3‐xylidine

A series of terpolymers were synthesized by the chemical oxidative polymerization of m‐phenylenediamine (MPD), o‐anisidine (AS), and 2,3‐xylidine (XY) in hydrochloride aqueous medium. The yield, intrinsic viscosity, and solubility of the terpolymers were studied by changing the MPD/AS/XY molar ratio from 100/0/0 to 53/39/8 to 0/100/0. It was discovered that the MPD/AS/XY terpolymers exhibit a higher polymerization yield and better solubility than MPD/AS and MPD/XY bipolymers having the same MPD molar content. The as‐prepared MPD/AS/XY terpolymer bases were characterized by Fourier transform infrared, ultraviolet–visible, ¹H NMR, and high‐resolution solid‐state ¹³C NMR spectroscopies; wide‐angle X‐ray diffraction; and thermogravimetry. The results suggested that the oxidative polymerization from MPD, AS, and XY is exothermic, and the resulting terpolymers are more easily soluble in some organic solvents than MPD homopolymer. The copolymer obtained was a real terpolymer containing MPD, AS, and XY units, and the actual MPD/AS/XY molar ratio calculated by solid‐state ¹³C NMR spectra of the polymers is very close to the feed ratio, although the AS content calculated on the basis of the ¹H NMR spectrum of the soluble part of the polymer is higher than the feed AS content. The terpolymers and MPD homopolymer exhibit a higher polymerization yield and much higher intrinsic viscosity and are more amorphous than the AS homopolymer. At a fixed MPD content of 70 mol %, the terpolymers exhibit an increased thermostability and activation energy of the major degradation in nitrogen and air with an increasing AS content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3989–4000, 2001     

Polymerization of aniline by copper‐catalyzed air oxidation

A novel method for preparing organosoluble and conducting polyaniline (PANI) is presented. It is demonstrated that Cu(II) is an excellent catalyst for the polymerization of aniline by air oxygen in aqueous emulsions. Reactions carried out at 0 °C or at room temperature yield PANIs of reasonably high molecular weights (number‐average molecular weight = 23,000–114,000 Da) in an emeraldine base form that are soluble in many organic solvents, such as tetrahydrofuran, dimethylformamide, N‐methylpyrrolidinone, chloroform, and acetone. Spectroscopic investigations (ultraviolet, Fourier transform infrared, and ¹H NMR) have shown that PANI obtained by this procedure has the same structure as those prepared by the conventional persulfate oxidation method. The resulting PANIs show reasonable electronic conductivities (0.067–0.320 S cm^?1) upon doping with p‐toluenesulfonic acid or dodecyl benzene sulfonic acid. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6025–6031, 2006     

In situ polymerization and morphology of polypyrrole obtained in water‐soluble polymer templates

Several water‐soluble polymers were used as templates for the in situ polymerization of pyrrole to determine their effect on the generation of nanosized polypyrrole (PPy) particles. The polymers used include: polyvinyl alcohol (PVA), polyethylene oxide (PEO), poly(vinyl butyral), polystyrene sulfonic acid, poly(ethylene‐alt‐maleic anhydride) (PEMA), poly(octadecene‐alt‐maleic anhydride), poly(N‐vinyl pyrrolidone), poly(vinyl butyral‐co‐vinyl alcohol‐co‐vinyl acetate), poly(N‐isopropyl acrylamide), poly(ethylene oxide‐block‐propylene oxide), hydroxypropyl methyl cellulose, and guar gum. The oxidative polymerization of pyrrole was carried out with FeCl₃ as an oxidant. The morphology of PPy particles obtained after drying the resulting aqueous dispersions was examined by optical microscopy, and selected samples were further analyzed via atomic force microscopy. Among the template polymers, PVA was the most efficient in generating stable dispersions of PPy nanospheres in water, followed by PEO and PEMA. The average size of PPy nanospheres was in the range of 160 nm and found to depend on the molecular weight and concentration of PVA. Model reactions and kinetics of the polymerization reaction of pyrrole in PVA were carried out by hydrogen ¹H NMR spectroscopy using ammonium persulfate as an oxidant. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of processable conducting copolymers from N‐ethylaniline with aniline

Copolymers were synthesized through the chemically oxidative polymerization of N‐ethylaniline (EA) and aniline (AN) in five acid aqueous media. The polymerization yield, intrinsic viscosity, molecular weight, solubility, solvatochromism, electrical conductivity, and mechanical properties of the copolymer films were systematically studied through changes in the comonomer ratio, polymerization temperature, oxidant, oxidant/monomer ratio, and acid medium. Open‐circuit‐potential and temperature measurements of the polymerization solutions showed that the polymerization rate depended on the EA content, and the polymerization was an exothermic reaction. The resultant copolymers were characterized in detail with IR, ultraviolet–visible, and ¹H NMR spectroscopy, gel permeation chromatography, wide‐angle X‐ray diffractometry, and scanning electron microscopy. The reactivity ratios of the monomer pair were calculated from the ¹H NMR spectra of the copolymers formed at a low conversion. The polymers exhibited good solubility and interesting solvatochromism in most of the solvents and variable conductivity with the EA/AN ratio and doping state. The conductivity of the HCl‐doped copolymers increased monotonically from 5.61 × 10^?7 to 2.55 × 10^?1 S/cm with decreasing EA content from 100 to 0 mol % and showed a percolation transition between EA concentrations of 20 and 30 mol %. The EA/AN copolymers also had excellent film formability and flexibility together with high mechanical and oxygen‐enriching properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6109–6124, 2004     

Sulfobetaine‐containing diblock and triblock copolymers via reversible addition‐fragmentation chain transfer polymerization in aqueous media

A novel bifunctional acrylamido‐based reversible addition–fragmentation chain transfer (RAFT) chain‐transfer agent (CTA), N,N′‐ethylenebis[2‐(thiobenzoylthio)propionamide] (CTA2), has been synthesized and used for the controlled free‐radical polymerization of N,N‐dimethylacrylamide (DMA). A comparative study of CTA2 and the monofunctional CTA N,N‐dimethyl‐s‐thiobenzoylthiopropionamide (CTA1) has been conducted. Polymerizations mediated by CTA1 result in poly(N,N‐dimethylacrylamide) (PDMA) homopolymers with unimodal molecular weight distributions, whereas CTA2 yields unimodal, bimodal, and trimodal distributions according to the extent of conversion. The multimodal nature of the PDMAs has been attributed to termination events and/or chains initiated by primary radicals. The RAFT polymerization of DMA with CTA2 also results in a prolonged induction period that may be attributed to the higher local concentration of dithioester functionalities early in the polymerization. A series of ω‐ and α,ω‐dithioester‐capped PDMAs have been prepared in organic media and subsequently employed as macro‐CTAs for the synthesis of diblock and triblock copolymers in aqueous media with the zwitterionic monomer 3‐[2‐(N‐methylacrylamido)‐ethyldimethylammonio] propane sulfonate (MAEDAPS). Additionally, an ω‐dithioester‐capped MAEDAPS homopolymer has been used as a macro‐CTA for the block polymerization of DMA. To our knowledge, this is the first example of a near‐monodisperse, sulfobetaine‐containing block copolymer prepared entirely in aqueous media. The diblock and triblock copolymers form aggregates in pure water that can be dissociated by the addition of salt, as determined by ¹H NMR spectroscopy and dynamic light scattering. In pure water, highly uniform, micellelike aggregates with hydrodynamic diameters of 71–93 nm are formed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1262–1281, 2003     

ABC‐type hetero‐arm star terpolymers through “Click” chemistry

Hetero‐arm star ABC‐type terpolymers, poly(methyl methacrylate)‐polystyrene‐poly(tert‐butyl acrylate) (PMMA‐PS‐PtBA) and PMMA‐PS‐poly(ethylene glycol) (PEG), were prepared by using “Click” chemistry strategy. For this, first, PMMA‐b‐PS with alkyne functional group at the junction point was obtained from successive atom transfer radical polymerization (ATRP) and nitroxide‐mediated radical polymerization (NMP) routes. Furthermore, PtBA obtained from ATRP of tBA and commercially available monohydroxyl PEG were efficiently converted to the azide end‐functionalized polymers. As a second step, the alkyne and azide functional polymers were reacted to give the hetero‐arm star polymers in the presence of CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine ( PMDETA) in DMF at room temperature for 24 h. The hetero‐arm star polymers were characterized by ¹H NMR, GPC, and DSC. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5699–5707, 2006     

N‐vinylcaprolactam‐based microgels: Effect of the concentration and type of cross‐linker

New microgel particles produced by using N‐vinylcaprolactam (VCL) and poly(ethylene glycol) diacrylate (PEGDA) or N,N′‐methylenbisacrylamide (BA) were synthesized in a batch reactor. The influence of the concentration and type of crosslinker on polymerization kinetics and colloidal characteristics of such temperature‐sensitive particles was studied. The partial and total conversion evolutions of VCL, PEGDA, and BA were determined by quantitative ¹H NMR and the average diameters of microgel particles together with the swelling–deswelling behavior were analyzed by means of photon correlation spectroscopy (PCS). Partial and total conversions, final average diameters at collapsed state, and the swelling–deswelling behavior varied as a function of the type of crosslinker. These results were attributed to the higher solubility and stabilizing ability of PEGDA compared with that of BA. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2766–2775, 2008     

Radical polymerization of novel N‐substituted‐N‐vinylformamide derivatives with bulky chiral substitutents

A series of novel N‐substituted‐N‐vinylformamides were synthesized, and the effect of bulky substituents on their radical polymerizability and polymer structure were investigated. N‐(p‐Methoxybenzyl)‐N‐vinylformamide ( 3 ) and N‐cyclohexylmethyl‐N‐vinylformamide ( 4 ) generated polymers, while it was known that their N‐vinylacetamide derivatives did not. ¹H NMR and ¹³C NMR analyses of poly( 3 ), however, revealed almost no difference among the various polymerization conditions, implying that the substituent bulkiness did not influence the polymer structures. On the other hand, the chiral polymers, which were obtained by the radical polymerization of N‐(S)‐2‐methylbutyl‐N‐vinylformamide ((S)‐ 5 ) and N‐(S)‐2,3‐dihydroxypropyl‐N‐vinylformamide ((S)‐ 7 ) at 0 °C, showed sharper spectral patterns than those obtained at higher polymerization temperatures. Furthermore, the intensities of their positive cotton effects on circular dichroism increased when the polymerization temperature was low, suggesting that the substituent bulkiness of (S)‐ 5 and (S)‐ 7 influenced the polymer structures, such as their stereoregularity and regioregularity. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Three‐component,negative‐type,alkaline‐developable,thermally stable,and photosensitive polymer based on poly(2,6‐dihydroxy‐1,5‐naphthalene), a crosslinker,and a photoacid generator

A negative working and chemically amplified photosensitive polymer has been developed, which is based on poly(2,6‐dihydroxy‐1,5‐naphthalene) (PDHN), the crosslinker 4,4′‐methylenebis[2,6‐bis(hydroxymethyl)]phenol, and the photoacid generator (5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐(2‐methylphenyl)acetonitrile. PDHN, with a number‐average molecular weight of 25,000, was prepared by the oxidative coupling polymerization of 2,6‐dihydroxynaphthalene with di‐μ‐hydroxo‐bis[(N,N,N′,N′‐tetramethylethylenediamine)copper(II)] chloride in 2‐methoxyethanol at room temperature. The resulting PDHN showed a 5% weight loss temperature of 440 °C in nitrogen and a low dielectric constant of 2.82. The resist showed a sensitivity of 8.3 mJ cm^?2 and a contrast of 11 when it was exposed to 436‐nm light, followed by postexposure baking at 100 °C for 5 min and development with a 2.38 wt % aqueous tetramethylammonium hydroxide solution at 25 °C. A fine negative image featuring 10‐μm line‐and‐space patterns was obtained on a film 3 μm thick exposed to 10 mJ cm^?2 of ultraviolet light at 436 nm in the contact‐printed mode. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2235–2240, 2004     

Synthesis of 4μ‐PS2PEO2, 4μ‐PS2PCL2, 4μ‐PI2PEO2, and 4μ‐PI2PCL2 star‐shaped copolymers by the combination of glaser coupling with living anionic polymerization and ring‐opening polymerization

4μ‐A₂B₂ star‐shaped copolymers contained polystyrene (PS), poly(isoprene) (PI), poly(ethylene oxide) (PEO) or poly(ε‐caprolactone) (PCL) arms were synthesized by a combination of Glaser coupling with living anionic polymerization (LAP) and ring‐opening polymerization (ROP). Firstly, the functionalized PS or PI with an alkyne group and a protected hydroxyl group at the same end were synthesized by LAP and then modified by propargyl bromide. Subsequently, the macro‐initiator PS or PI with two active hydroxyl groups at the junction point were synthesized by Glaser coupling in the presence of pyridine/CuBr/N,N,N ′,N ″,N ″‐penta‐methyl diethylenetri‐amine (PMDETA) system and followed by hydrolysis of protected hydroxyl groups. Finally, the ROP of EO and ε‐CL monomers was carried out using diphenylmethyl potassium (DPMK) and tin(II)‐bis(2‐ethylhexanoate) (Sn(Oct)₂) as catalyst for target star‐shaped copolymers, respectively. These copolymers and their intermediates were well characterized by SEC, ¹H NMR, MALDI‐TOF mass spectra and FT‐IR in details. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis,characterization, and thermal properties of a novel pentaerythritol‐initiated star‐shaped poly(p‐dioxanone)

A novel star‐shaped poly(p‐dioxanone) was synthesized by the ring‐opening polymerization of p‐dioxanone initiated by pentaerythritol with stannous octoate as a catalyst in bulk. The effect of the molar ratio of the monomer to the initiator on the polymerization was studied. The polymers were characterized with ¹H NMR and ¹³C NMR spectroscopy. The thermal properties of the polymers were investigated with differential scanning calorimetry and thermogravimetric analysis. The novel star‐shaped poly(p‐dioxanone) has a potential use in biomedical materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1245–1251, 2006     

Are N‐substituted glycine N‐thiocarboxyanhydride monomers really hard to polymerize?

N‐Substituted glycine N‐thiocarboxyanhydrides (NNTAs) are promising cyclic monomers to synthesize polypeptoids with the advantages of easier preparation and higher stability during purification and storage than N‐substituted glycine N‐carboxyanhydrides (NNCAs). NNTAs were commonly considered too stable to polymerize for their low reactivity. In this contribution, we report controlled polymerizations of N‐ethylglycine NTA (NEG‐NTA) and sarcosine NTA (Sar‐NTA) using primary amines as initiator under proper polymerization conditions. The controllability has been fully supported by ¹H NMR end group analyses, MALDI‐ToF mass spectra, kinetic data, block copolymerizations by sequential monomer addition, and low polydispersities (1.14–1.17) of polypeptoids. Variation of the [NNTA]/[initiator] ratio allows well control of the molar mass, and degrees of polymerization (DPs) up to 287 can be reached for poly(N‐ethylglycine) or DPs up to 262 for polysarcosine. NNTAs exhibit excellent activity and they are potential to synthesize polypeptoids with controllable polymerization. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 404–410     

4‐methoxy‐substituted poly(triphenylamine): A p‐type polymer with highly photoluminescent and reversible oxidative electrochromic characteristics

A 4‐methoxy‐substituted triphenylamine‐containing homopolymer, poly [N,N‐diphenyl‐4‐methoxyphenylamine‐4′,4′′‐diyl] ( PMeOTPA ), with blue light (435 nm) fluorescence quantum efficiency up to 79% was easily prepared by oxidative coupling polymerization of N,N‐diphenyl‐4‐methoxyphenylamine ( MeOTPA ) using FeCl₃ as an oxidant. Its reversible oxidation redox couple was at 0.41 V versus Fc/Fc⁺ in acetonitrile solution. It exhibited good thermal stability with 10% weight‐loss temperatures above 500 °C under a nitrogen atmosphere and relatively high softening temperature (154 °C). The simply designed homopolymer revealed moderate stability of electrochromic characteristics, changing color from original pale yellowish to red, and then to black. The PMeOTPA based field effect transistor also showed p‐type characteristics with significant temperature dependence. The present study suggests that PMeOTPA is a multifunctional polymer for various optoelectronic device applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3292–3302, 2007     

Effect of catalyst systems and reaction conditions on the synthesis of cellulose‐g‐PDMAam copolymers by controlled radical polymerization

Various copper‐based catalyst systems and reaction conditions were studied in the graft copolymerization of N,N‐dimethylacrylamide (DMAam) with a cellulose‐based macroinitiator by controlled radical polymerization. The cellulose macroinitiator with degree of substitution DS = 0.44 was synthesized from dissolving softwood pulp in a LiCl/DMAc solution. The graft copolymerizations of DMAam, using the cellulose macroinitiator and various copper‐based catalyst systems, were then carried out in DMSO solutions. The copolymerization kinetics was followed by ¹H NMR. Water‐soluble cellulose‐g‐PDMAam copolymers were comprehensively characterized by ATR‐FTIR and ¹H NMR spectroscopies and SEC analyses. DLS and steady‐shear viscosity measurements revealed that when the DP_graft of the cellulose‐g‐PDMAam copolymer is high enough, the copolymer forms a more compact structure in water. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of tris(2,2′‐bipyridine)ruthenium‐cored star‐shaped polymers via RAFT polymerization

A new bipyridine‐functionalized dithioester was synthesized and further used as a RAFT agent in RAFT polymerization of styrene and N‐isopropylacrylamide. Kinetics analysis indicates that it is an efficient chain transfer agent for RAFT polymerization of the two monomers which produce polystyrene and poly(N‐isopropylacrylamide) polymers with predetermined molecular weights and low polydispersities in addition to the end functionality of bipyridine. The bipyridine end‐functionalized polymers were further used as macroligands for the preparation of star‐shaped metallopolymers. Hydrophobic polystyrene macroligand combined with hydrophiphilic poly(N‐isopropylacrylamide) was complexed with ruthenium ions to produce amphiphilic ruthenium‐cored star‐shaped metallopolymers. The structures of these synthesized metallopolymers were further elucidated by UV–vis, fluorescence, size exclusion chromatography (SEC), and differential scanning calorimetry (DSC) as well as NMR techniques. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4225–4239, 2007     

New Linear and Star‐Shaped Thermogelling Poly([R]‐3‐hydroxybutyrate) Copolymers

The synthesis of multi‐arm poly([R]‐3‐hydroxybutyrate) (PHB)‐based triblock copolymers (poly([R]‐3‐hydroxybutyrate)‐b‐poly(N‐isopropylacrylamide)‐b‐[[poly(methyl ether methacrylate)‐g‐poly(ethylene glycol)]‐co‐[poly(methacrylate)‐g‐poly(propylene glycol)]], PHB‐b‐PNIPAAM‐b‐(PPEGMEMA‐co‐PPPGMA), and their subsequent self‐assembly into thermo‐responsive hydrogels is described. Atom transfer radical polymerization (ATRP) of N‐isopropylacrylamide (NIPAAM) followed by poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) and poly(propylene glycol) methacrylate (PPGMA) was achieved from bromoesterified multi‐arm PHB macroinitiators. The composition of the resulting copolymers was investigated by ¹H and ¹³C J‐MOD NMR spectroscopy as well as size‐exclusion chromatography (SEC), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The copolymers featuring different architectures and distinct hydrophilic/hydrophobic contents were found to self‐assemble into thermo‐responsive gels in aqueous solution. Rheological studies indicated that the linear one‐arm PHB‐based copolymer tend to form a micellar solution, whereas the two‐ and four‐arm PHB‐based copolymers afforded gels with enhanced mechanical properties and solid‐like behavior. These investigations are the first to correlate the gelation properties to the arm number of a PHB‐based copolymer. All copolymers revealed a double thermo‐responsive behavior due to the NIPAAM and PPGMA blocks, thus allowing first the copolymer self‐assembly at room temperature, and then the delivery of a drug at body temperature (37 °C). The non‐significant toxic response of the gels, as assessed by the cell viability of the CCD‐112CoN human fibroblast cell line with different concentrations of the triblock copolymers ranging from 0.03 to 1 mg mL^?1, suggest that these PHB‐based thermo‐responsive gels are promising candidate biomaterials for drug‐delivery applications.     

Easy synthesis and ring‐opening polymerization of 5‐Z‐amino‐δ‐valerolactone: New degradable amino‐functionalized (Co)polyesters

Novel 5‐Z‐amino‐δ‐valerolactone (5‐NHZ‐VL) was synthesized with an aim to prepare degradable polyesters and copolyesters having amino pendant groups. Following a straightforward and efficient synthetic pathway, 5‐NHZ‐VL was obtained in only two steps and up to 50% yield. The monomer was fully characterized by ¹H NMR, ¹³C NMR, ESI mass spectrometry, and HPLC. Various conventional conditions were tested for this lactone ring‐opening polymerization and led to the novel corresponding poly(5‐NHZ‐VL) (M_n = 7000 g/mol; PD = 1.2). Following this homopolymerization, 5‐NHZ‐VL was copolymerized with ε‐caprolactone to generate a family of copolyesters with an amino‐group content ranging from 10 to 80%. Finally, the polyelectrolyte poly(5‐NH₃⁺‐VL) was recovered by removal of the protecting group under acidic conditions, and integrity of the polyester backbone was confirmed by ¹H NMR. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of low‐polydispersity poly(N‐ethylmethylacrylamide) by controlled radical polymerizations and their thermal phase transition behavior

Controlled radical polymerizations of N‐ethylmethylacrylamide (EMA) by atom transfer radical polymerization and reversible addition‐fragmentation chain transfer processes were investigated in detail for the first time, employing complementary characterization techniques including gel permeation chromatography, ¹H NMR spectroscopy, and matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry. In both cases, relatively good control of the polymerization of EMA was achieved, as revealed by the linear evolution of molecular weights with monomer conversions and the low polydispersity of poly(N‐ethylmethylacrylamide) (PEMA). The thermal phase transitions of well‐defined PEMA homopolymers with polydispersities less than 1.2 and degrees of polymerization up to 320 in aqueous solution were determined by temperature‐dependent turbidity measurements. The obtained cloud points (CPs) vary in the range of 58–68 °C, exhibiting inverse molecular weight and polymer concentration dependences. Moreover, the presence of a carboxyl group instead of an alkyl one at the PEMA chain end can elevate its CP by ～3–4 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 60–69, 2008     

Controlled grafting of ethyl cellulose with azobenzene‐containing polymethacrylates via atom transfer radical polymerization

Graft copolymers of ethyl cellulose with azobenzene‐containing polymethacrylates were synthesized through atom transfer radical polymerization (ATRP). The residual hydroxyl groups on ethyl cellulose were first esterified with 2‐bromoisobutyryl bromide to yield 2‐bromoisobutyryloxy groups, which was then used to initiate the polymerization of 6‐[4‐(4‐methoxyphenylazo)phenoxy]hexyl methacrylate (MMAzo) in the presence of CuBr/N,N,N′,N″,N″‐pentamethylenetriamine (PMDETA) as catalyst and anisole as solvent. The graft copolymers were characterized by gel permeation chromatography (GPC) and ¹H‐NMR. The molecular weights of the graft copolymers increased relatively to the macroinitiator, and the polydispersities were narrow. The thermal and liquid crystalline property of the graft copolymers were investigated by differential scanning calorimeter (DSC) and polarizing optical microscope (POM). Photoresponsive property was studied under the irradiation of UV–vis light in THF solution. The graft copolymers have potential applications, including sensors and optical materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1653–1660, 2007