Isothermal Crystallization of Isotactic Poly(propylene) Studied by Superfast Calorimetry

The isothermal crystallization behavior and the structure and morphology of isotactic poly(propylene) (iPP) and iPP/hydrogenated hydrocarbon resin (HR) 90/10 blend were analyzed. To cover the entire temperature range, isothermal crystallizations were studied using superfast calorimetry at a high cooling rate in the range 0 to 110 °C, and by conventional DSC at a low cooling rate in the range 120 to 140 °C. Structural and morphological changes due to the different thermal treatments were also analyzed. The complete crystallization curve ranging from T_g to T_m showed bimodal crystallization behaviors for both iPP and iPP/HR 90/10 blend. This result is explained by taking into consideration the polymorph properties of iPP. It is in fact assumed that the curve from T_g to 60 °C referred mainly to the crystallization kinetics of the iPP mesomorphic form by homogeneous nucleation, whereas the curve from 60 °C to T_m mainly represented the crystallization kinetic curve for the monoclinic α form by heterogeneous nucleation. This hypothesis is confirmed by the analysis of the structures obtained using wide angle X‐ray experiments. Moreover, the addition of HR to iPP causes a drastic reduction in the crystallization rate of iPP in both regions due to the diluent effect of the miscible resin.

     

Synthesis and Characterization of Double Crystalline Cyclic Diblock Copolymers of Poly(ε‐caprolactone) and Poly(l(d)‐lactide) (c(PCL‐b‐ PL(D)LA))

The synthesis of symmetric cyclo poly(ε‐caprolactone)–block–poly(l (d )‐lactide) (c(PCL–b–PL(D)LA)) by combining ring‐opening polymerization of ε‐caprolactone and lactides and subsequent click chemistry reaction of the linear precursors containing antagonist functionalities is presented. The two blocks can sequentially crystallize and self‐assemble into double crystalline spherulitic superstructures. The cyclic chain topology significantly affects both the nucleation and the crystallization of each constituent, as gathered from a comparison of the behavior of linear precursors and cyclic block copolymers. The stereochemistry of the PLA block does not have a significant effect on the nonisothermal crystallization of both linear and cyclo PCL‐b‐PDLA and PCL‐b‐PLLA copolymers.

     

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate)–Poly(vinyl‐acetate) blends

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate) (PHB)–poly(vinyl acetate) (PVAc) blends from the melt were investigated by differential scanning calorimetry using various cooling rates. The results show that crystallization of PHB from the melt in the PHB–PVAc blends depends greatly upon cooling rates and blend compositions. For a given composition, the crystallization process begins at higher temperatures when slower scanning rates are used. At a given cooling rate, the presence of PVAc reduces the overall PHB crystallization rate. The Avrami analysis modified by Jeziorny and a new method were used to describe the nonisothermal crystallization process of PHB–PVAc blends very well. The double‐melting phenomenon is found to be caused by crystallization during heating in DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 443–450, 1999     

In‐Reactor Compounding Metallocenic Isotactic Poly(propylene)/Nucleation Agent Compositions by Employing the Nucleation Agent as a Catalyst Support

A nucleation agent, 1,3,2,4‐dimethylbenzylidene sorbitol (DMBS), was used as a support for C₂‐symmetric metallocene rac‐Me₂Si[2‐Me‐4‐Naph‐Ind]₂ZrCl₂. Propylene polymerization with the supported catalyst resulted in i‐PP polymers with granular morphology. The role of a catalyst support ensures a good dispersion of the nucleation agent in the formed i‐PP matrix. The employment of a nucleation agent as catalyst support provides a unique solution to in‐reactor compounding metallocenic i‐PP/nucleation agent compositions.

     

Effect of calcium malonate on the formation of β crystalline form in isotactic poly(propylene)

Calcium malonate (Camt) is used to induce the β crystalline form in isotactic polypropylene (iPP) for the first time. The relative content of the β crystalline form (K value) increases markedly with the addition of Camt and attains the maximum value of 73.48% at 0.40% Camt. The amounts of bright and colorful β spherulites increase and the spherulitic sizes decrease with the increase in Camt contents. The tensile strength and the Izod notched impact strength of the nucleated iPP samples increase with the addition of Camt; in particular, the latter almost doubles at 0.40% Camt compared to that of the blank iPP sample. The β nucleation mechanism of Camt is analyzed by the dimensional lattice match criterion. Copyright © 2008 John Wiley & Sons, Ltd.     

Large Plastic Deformation of Isotactic Poly(propylene) (iPP) Evaluated by WAXD Techniques

Summary: Commercial isotactic poly(propylene) (iPP), obtained in bars, was annealed and submitted to different levels of plastic deformation by uniaxial plane compression using a special device which permits well controlled temperature and strain rate. The evolution of the microstructure was followed at different degrees of deformation by wide angle x-ray diffraction (WAXD) techniques. The spherulite fragmentation process, lamellar orientation and destruction of the crystallites is argued, according to collected analytical data in the flow direction (FD), the loading direction (LD) and the lateral or constrain direction (CD). The evaluation of the WAXD patterns in terms of diffraction line position, intensity and width, permits to affirm that, while the large plastic deformation occurs, the crystalline net suffers anisotropic deformation, the crystallites become preferentially oriented along the flow direction and the crystalline phase diminish in amount indicating lesser and smaller crystallites. The gradual lamellae fragmentation occurs, starting with apparent crystalline size of approximately 30 nm for the non-deformed material and gradually decreasing to approximately 15 nm for the 70% deformed one.     

Fractionation and Crystallization of Isotactic Poly(propylenes) Prepared with a Heterogeneous Transition Metal Catalysts

Summary: A series of poly(propylenes) (PPs) were prepared by slurry polymerization using a MgCl₂-supported transition metal catalyst. Two different external donors (EDs) were used: diphenyl dimethoxysilane (DPDMS) and methylphenyl dimethoxysilane (MPDMS). The molecular weight (MW) of the PPs was controlled using molecular hydrogen that was used as a transfer agent. To obtain materials with differing molecular weight and similar tacticities, polymers were fractionated with prep-TREF. DSC analyses of blends of TREF fractions showed that the crystallization behaviour of the polymer blends are strongly affected by the configuration (tacticity) and MW of the PP.     

Molecular‐Weight‐Dependence on Domain Formation of Grafted Poly(ethylene‐co‐propylene) in a Poly(propylene) Matrix

Several novel poly(propylene)‐graft‐poly(ethylene‐co‐propylene) copolymers with isotactic poly(propylene) (PP) backbones and ethylene/propylene rubber (EPR) branches were synthesized. The thermomechanical properties of these samples were investigated using a dynamic mechanical analyzer. There appeared to be a critical EPR molecular weight above which a two‐phase system developed with EPR domains dispersed in a PP matrix. This domain formation gave an enhanced loss modulus compared to a commercial high impact PP product below 40°C.     

Effect of Pressure on the Miscibility of Polyethylene/Poly(ethylene‐alt‐propylene) Blends

Summary: Effect of density, and hence pressure, on the miscibility of a 50:50 mol/mol PE/PEP blend was studied using a coarse‐grained MC simulation approach on a high‐coordination lattice, with the conformations of the coarse‐grained chains constrained by the RIS model. Interchain pair correlation functions are used to assess the miscibility of the mixtures. Miscibility increases with increasing temperature over the range −50–150 °C. It is rather insensitive to pressure at high temperatures, but at −50 °C, the blend miscibility increases with decreasing pressure. The findings are consistent with the fact that the blend is an UCST blend and that the simulation temperatures used, except −50 °C, were considerably higher than the UCST of the blend. The pressure dependence of the blend miscibility observed near −50 °C is also in agreement with the experimental observation that the blend exhibits a negative volume change of mixing. The present work demonstrates that the coarse‐grained MC approach, when it is used with periodic boundary cells of different sizes filled with the same number of chains, is capable of capturing the pressure dependence of UCST blends. In addition, such a simulation also provides us with insights about the molecular origin of the observed pressure dependence of miscibility. In the present case, the segregation of PE and PEP chains at low temperatures and high pressure simply originates from the fact that fully extended segments of PE chains tend to cluster so that their intermolecular interactions can be maximized. As the temperature increases, there is a decrease in the probability of a trans state at a C C bond in PE, and therefore the attraction between the PE chains is reduced at higher temperatures, promoting miscibility and the UCST behavior.

Density (pressure) dependence of the 2^nd shell pair correlation function values for a 50/50 PE/PEP blend at −50 °C.     

环氧丙烷聚醚三元醇/左旋聚乳酸三枝链嵌段共聚物的结晶行为

采用DSC对环氧丙烷聚醚三元醇/左旋聚乳酸三枝链嵌段共聚物(PPO-b-PLLA)的熔体结晶行为进行了研究. 在388～407 K范围内, 分别采用Avrami方程和Arrhenius方程进行了结晶动力学计算. Avrami指数n值约为2.2, 表明共聚物以二维生长方式进行晶体生长. 基于LH结晶理论, 对三枝链嵌段共聚物的结晶机理进行了探讨. 实验发现该体系共聚物的Regime II和Regime III转变温度随着n(PO)∶n(LA)的增大而变化, Kg (III)/Kg (II)＝2.0～2.2, 与LH理论预期值吻合. 实验结果表明三枝链的PPO链段对PLLA链段的结晶有很大影响, 使其成核较均聚物困难. 链折叠自由能σe和链折叠功q均高于PLLA的值.     

Interplay of fractionated crystallization and morphology in polypropylene/poly(ϵ‐caprolactone) blends

The thermal behavior of melt‐mixed polypropylene (PP)/poly(?‐caprolactone) (PCL) blends was investigated with differential scanning calorimetry, and it was quantitatively related to the morphology observed through scanning electron microscopy. The PP/PCL blends were immiscible in the whole composition range; however, some interesting phenomena were found. Blends with low PP contents crystallized in a fractionated fashion. By applying a self‐nucleation procedure, we demonstrated that this occurred because of a lack of highly active heterogeneities within the confined PP domains. On the other hand, PP acted as a nucleating agent for PCL, and when the PP content was reduced, the higher surface/volume ratio increased its nucleating activity. The nucleating effect was improved when the PP was self‐nucleated because of the better nucleating effect of PP annealed crystals. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1365–1379, 2007     

Synthesis and Characterization of a Block Copolymer Containing Regioregular Poly(3‐hexylthiophene) and Poly(γ‐benzyl‐L‐glutamate)

Poly(3‐hexylthiophene)‐b‐poly(γ‐benzyl‐L ‐glutamate) (P3HT‐b‐PBLG) rod–rod diblock copolymer was synthesized by a ring‐opening polymerization of γ‐benzyl‐L ‐glutamate‐N‐carboxyanhydride using a benzylamine‐terminated regioregular P3HT macroinitiator. The opto‐electronic properties of the diblock copolymer have been investigated. The P3HT precursor and the P3HT‐b‐PBLG have similar UV–Vis spectra both in solution and solid state, indicating that the presence of PBLG block does not decrease the effective conjugation length of the semiconducting polythiophene segment. The copolymer displays solvatochromic behavior in THF/water mixtures. The morphology of the diblock copolymer depends upon the solvent used for film casting and annealing results in morphological changes for both films deposited from chloroform and trichlorobenzene.

     

Crosslinking of Poly(L‐lactide) by γ‐Irradiation

The radiation crosslinking of poly(L ‐lactide) (PLLA) was investigated using triallyl isocyanurate (TAIC) as a crosslinking agent. The gel fraction of crosslinked PLLA increased with TAIC concentration and γ‐ray dose. Crosslinking of PLLA started at low TAIC contents and low γ‐ray dosage. Differential scanning calorimetry and dynamic mechanical thermal analysis revealed that PLLA was completely crosslinked at high weight ratios and high γ‐ray doses.     

Synthesis and non‐isothermal crystallization kinetics of poly(ethylene terephthalate)‐co‐poly(propylene glycol) copolymers

Poly(ethylene terephthalate)‐co‐poly(propylene glycol) (PET‐co‐PPG) copolymers with PPG ratio ranging from 0 to 0.90 mol% were synthesized by the melt copolycondensation. The intrinsic viscosity, structure, non‐isothermal crystallization behavior, nucleation and spherulitic growth of the copolymers were investigated by Ubbelohde viscometer, Proton Nuclear Magnetic Resonance (¹H‐NMR), differential scanning calorimetry, and polarized optical microscopy, respectively. The non‐isothermal crystallization process of the copolymers was analyzed by Avrami, Ozawa, Mo's, Kissinger, and Dobreva methods, respectively. The results showed that the crystallizability of PET was apparently enhanced with incorporating a small amount of PPG, which first rose and then reduced with increasing amount of PPG in the copolymers at a given cooling rate. The crystallization mechanism was a three‐dimensional growth with both instantaneous and sporadic nucleation. Particularly, PET‐co‐PPG containing 0.60 mol% PPG exhibited the highest crystallizability among all the copolymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Isotactic Poly(propylene)/Monoalkylimidazolium‐Modified Montmorillonite Nanocomposites: Preparation by Intercalative Polymerization and Thermal Stability Study

Summary: Poly(propylene)/monoalkylimidazolium‐modified montmorillonite (PP/IMMT) nanocomposites were prepared by in situ intercalative polymerization of propylene with TiCl₄/MgCl₂/MMT catalyst. The PP synthesized possessed high isotacticity and molecular weight. Both wide‐angle X‐ray diffraction (XRD) and transmission electron microscopy (TEM) examinations evidenced the nanocomposite formation with exfoliated MMT homogeneously distributed in the PP matrix. A thermal stability study revealed that the nanocomposites possess good thermal stability.

X‐ray diffraction patterns of PP/IMMT (MMT = 2.2 wt.‐%) nanocomposite before and after processing.     

Shear‐Controlled Micro/Nanometer‐Scaled Super‐Hydrophobic Surfaces with Tunable Sliding Angles from Single Component Isotactic Poly(propylene)

Summary: With the proper selection of shear and thermal conditions, super‐hydrophobic polymeric surfaces (contact angle > 150°) with tunable sliding angles (from less than 1° to higher than 90°) can be prepared from pure isotactic poly(propylene) (iPP) without any further modification with low‐surface‐energy components under ambient atmosphere. The formed surfaces have naturally good thermal properties, chemical and moisture resistance, low density, and potentially low manufacturing cost.

SEM images of formed super‐hydrophobic surfaces and related two extreme sliding angles (contact angles of these surfaces are higher than 150°).     

Poly(ε‐caprolactone)–poly(isobutylene): A crystallizing,hydrogen‐bonded pseudo‐block copolymer

The crystallization of block copolymers (BCPs) under homogeneous and heterogeneous nucleation is currently well understood revealing the strong interplay of crystallization in competition to microphase separation. This article reports investigations on synthesis and crystallization processes in weakly interacting supramolecular pseudo‐BCPs, composed of poly(ε‐caprolactone) (PCL) and poly(isobutylene) (PIB) blocks, connected by a specifically interacting hydrogen bond (thymine/2,6‐diaminotriazine). Starting from ring opening polymerization of ε‐caprolactone, the use of “click”‐chemistry enabled the introduction of thymine endgroups onto PCL polymer, thus generating the fully thymine‐substituted pure PCLs ( 1a , 1b ) as judged via NMR and MALDI analysis. Physical mixing of 1a , 1b with a bivalent, bis(2,6‐diaminotriazine)‐containing molecule ( 2 ) generated the bivalent polymers BC1 and BC2 , whereas mixing of 1a or 1b with the 2,6‐diaminotriazine‐substituted PIB ( 3 ) generated the supramolecular pseudo‐BCPs BC3 and BC4 . Thermal investigations (DSC, Avrami analysis) revealed only minor changes in the crystallization behavior of BC1 – BC4 with Avrami exponents close to three, indicative of a confluence of the growing crystals during the crystallization process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Nucleating Effect and Dynamic Crystallization of a Poly(propylene)/Talc System

The addition of nucleating agents to semicrystalline polymersis largely used in the processing industry of plastic materials to improve some properties of polymers as well as for economical and technological reasons. In this work, the influence of talc concentration on the nucleation efficiency of poly(propylene) (PP), as well as on the non-isothermal kinetics of the crystallization of that system were determined by differential scanning calorimetry (DSC). The nucleating efficiency was determined by Fillon's method, and the dynamic nucleation by Ozawa's method at cooing rates of 2, 5 and 10°C min^–1. The results show that both the degree of crystallinity and the crystallization temperature increase with the filler content and decrease at higher cooling rates and that Ozawa's (n,) exponent and the nucleation efficiency increase with temperature and filler content. It was also shown that the nucleating efficiency of talc in poly(propylene) is comparable to the best heterogeneous nucleating agents available. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis and Characterization of Star‐Shaped Diblock Poly(ε‐caprolactone)/Poly(ethylene oxide) Copolymers

Summary: Star‐shaped hydroxy‐terminated poly(ε‐caprolactone)s (ssPCL), with arms of different lengths, were obtained by ring‐opening polymerization (ROP) of ε‐caprolactone initiated by pentaerythritol, and were condensed with α‐methyl‐ω‐(3‐carboxypropionyloxy)‐poly(ethylene oxide)s ( = 550–5 000) to afford four‐armed PCL‐PEO star diblock copolymers (ssPCL‐PEO). The polymers were characterized by ¹H and ¹³C NMR spectroscopy and size‐exclusion chromatography (SEC). The melting behavior of ssPCLs was studied by differential scanning calorimetry (DSC). X‐ray diffraction and DSC techniques were used to investigate the crystalline phases of ssPCL‐PEOs.

The part of the synthesis of four‐armed star‐shaped diblock poly(ε‐caprolactone)‐poly(ethylene oxide) copolymers as described.