Solvent Influences the Morphology and Mechanical Properties of Electrospun Poly(L-lactic acid) Scaffold for Tissue Engineering Applications

Electrospun micro- and nanofiber scaffolds have gained interest in biomedical applications, especially in tissue engineering, because they can be used to reproduce the structure of the extracellular matrix (ECM) of natural tissue. The selection of the solvent is an important factor which affects the diameter, the surface morphology and the crystallinity of the electrospun fibers, and, accordingly, their mechanical properties as well as their degradation kinetics. Furthermore, the surface morphology of the electrospun fibres can be controlled by solvent vapour pressure to produce porous structures which might be helpful for cell adhesion and proliferation. In the present work, poly (L-lactic acid) (PLLA) has been electrospun using solvents with different vapour pressures to investigate the influences of the solvent vapour pressure on morphology, diameter, crystallinity and mechanical properties of the electrospun fiber scaffolds. The results show that the vapour pressure of the solvents (or solvent mixtures) play an important role in the fiber diameter and crystallinity. Furthermore, the crystallinity of the fibers is increased by lowering the vapour pressure of the used solvent. In addition, the mechanical properties (e.g., tensile strength and Young's modulus) are strongly dependent on morphological features such average fibers diameter. The smaller the average diameter, the higher the tensile strength and Young's modulus.     

Electrospun EGNPs reinforced precursor carbon nanofibril composites by using RSM

Response surface methodology (RSM),based on five‐level, four variable Box‐Benkhen technique was investigated for modeling the average fiber diameter of electrospun polyacrylonitrile (PAN) nanofibers. The four important electrospinning parameters were studied including applied voltage (kV), Berry's number, deposition distance from nozzle to collector (cm), and spinning angle (? in degree). The measured fiber diameters were in a good agreement with the predicted results by using RSM technique. High‐regression coefficient between the variables and the response (R² = 87.74%) indicates excellent evaluation of experimental data by second‐order polynomial regression model. The optimum PAN average fiber diameters of 208 and 37‐nm standard deviation were collected at 19 kV, Berry's number = 10, 25^° spinning angle, and 16‐cm deposition distance. The PAN/N,N‐dimethylformamide (DMF) polymer solution with the optimum weight concentration (10 wt.%) was selected to study the effect of dispersing exfoliated graphite nanoplatelets (EGNPs) in PAN/DMF solution on the electrospun EGNP/PAN fibril composite diameter. Five different EGNPs weight concentrations (2, 4, 6, 8, and 10 wt.%) were dispersed in the optimized PAN/DMF polymer solution. Morphology of EGNPs/PAN fibril composites and its distribution were investigated by scanning electron microscopy (SEM) to show the minimum fiber diameter for the above‐mentioned 5 wt. % of EGNPs. A minimum fibril composite diameter of 182 nm was obtained at 10 wt.% of EGNPs. Morphological characteristics of electrospun fibers and their distribution were tested by Raman spectroscopy, SEM, differential light scattering, and high‐resolution transmission electron microscopy.     

Measurement of size‐dependent glass transition temperature in electrospun polymer fibers using AFM nanomechanical testing

The glass transition temperature (T_g) of individual electrospun polymer polyvinyl alcohol fibers of varying diameter was measured using atomic force microscopy (AFM) based nanomechanical thermal analysis. Indentation and bending of individual electrospun fibers using AFM allowed the calculation of the elastic modulus of the polyvinyl alcohol (PVA) fibers across a range of different temperatures. The elastic modulus of electrospun PVA fibers was observed to decrease significantly when passing through T_g, which allowed accurate determination of T_g. The T_g of electrospun PVA fibers was shown to decrease for smaller fiber diameters especially for fiber diameters below 250 nm. This size‐dependent glass transition behavior of electrospun PVA fibers is indicated as being due to polymer chain confinement. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Poly(dicyclopentadiene) Submicron Fibers Produced by Electrospinning

Summary: We have used the process of electrospinning to produce fibers of poly(dicyclopentadiene) with diameters on the submicron scale. The material, formed from a monomer‐catalyst solution, polymerized in flight during the electrospinning process. Fibers were collected over trenches etched in silicon and the Young's moduli were measured using an atomic force microscope to measure force‐displacement curves. The resulting values of Young's moduli are larger than typical values for bulk polymer material.

SEM image of suspended PDCPD fiber.     

A study on the orientation structure and mechanical properties of polyacrylonitrile precursors

The polyacrylonitrile precursors were made through the two‐stage drawing process. The orientation structure was examined through wide‐angle X‐ray diffraction (WAXD). The orientation factors and the modulus were measured through the sound velocity method. The mechanical properties, such as the Young's modulus, the tensile strength and the breaking elongation ratio were obtained by the single fiber tensile test. The results showed that the Young's modulus and the strength of the precursors increased with draw ratio, which is accordant with the enhancement of the micromolecular orientation degree. Therefore the orientation factors obtained from the experiments were compared with the theoretical curves which were predicted through the Crawford and Kolsky's model. The physical meaning of the parameters m and n were analyzed. A good agreement of the orientation factor between the experimental data and the theoretical curve was achieved. Copyright © 2005 John Wiley & Sons, Ltd.     

Tensile deformation of electrospun nylon‐6,6 nanofibers

Nylon‐6,6 nanofibers were electrospun at an elongation rate of the order of 1000 s^?1 and a cross‐sectional area reduction of the order of 0.33 × 10⁵. The influence of these process peculiarities on the intrinsic structure and mechanical properties of the electrospun nanofibers is studied in the present work. Individual electrospun nanofibers with an average diameter of 550 nm were collected at take‐up velocities of 5 and 20 m/s and subsequently tested to assess their overall stress–strain characteristics; the testing included an evaluation of Young's modulus and the nanofibers' mechanical strength. The results for the as‐spun nanofibers were compared to the stress–strain characteristics of the melt‐extruded microfibers, which underwent postprocessing. For the nanofibers that were collected at 5 m/s the average elongation‐at‐break was 66%, the mechanical strength was 110 MPa, and Young's modulus was 453 MPa, for take‐up velocity of 20 m/s—61%, 150 and 950 MPa, respectively. The nanofibers displayed α‐crystalline phase (with triclinic cell structure). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1482–1489, 2006     

Mechanical properties and structure of the zone‐drawn poly(L‐lactic acid) fibers

The zone‐drawing (ZD) method was applied three times to the melt‐spun poly(L ‐lactic acid) (PLLA) fibers of low molecular weight (M_v = 13,100) at different temperatures under various tensions. The mechanical properties and superstructure of the ZD fibers were investigated. The resulting ZD‐3 fiber had a draw ratio of 10.5, birefringence of 37.31 × 10⁻³, and crystallinity of 37%, while an orientation factor of crystallites remarkably increased to 0.985 by the ZD‐1. The Young's modulus and tensile strength of the ZD‐3 fiber respectively attained 9.1 GPa and 275 MPa, and the dynamic storage modulus was 10.4 GPa at room temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 991–996, 1999     

The morphology and crystalline region distribution of polyacrylonitrile nanofibers prepared by electrospinning

The effects of electrospinning parameters in a wider range on the morphology and diameters of polyacrylonitrile (PAN) fibers are studied in detail. The fibers’ diameter increases from 288 to 3469 nm swiftly with the increasing PAN concentration. With the increasing voltage or prolonging gap distance, the diameter increases primarily and decreases later. The combined effects of surface tension, splitting and stretching, electric force, viscosity, and solvent volatilization are the main reasons. Ultrasonic etching method, Atomic force microscope (AFM), Scanning electron microscope (SEM) and X-ray diffraction (XRD) technology have been utilized to verify the nature structure of electrospun PAN fibers. Combining all the results, it is deduced that there are many grooves arranging nearly perpendicular to the fiber axis on the surface of electrospun PAN fibers. The thickness of relative ordered region is 40 to 190 nm and the thickness of amorphous region is 20 to 35 nm.     

Controlling electrospun nanofiber morphology and mechanical properties using humidity

Electrospinning is a fiber spinning technique used to produce nanoscale polymeric fibers with superior interconnectivity and specific surface area. The fiber diameter, surface morphology, and mechanical strength are important properties of electrospun fibers that can be tuned for diverse applications. In this study, the authors investigate how the humidity during electrospinning influences these specific properties of the fiber mat. Using two previously uninvestigated polymers, poly(acrylonitrile) (PAN) and polysulfone (PSU) dissolved in N,N‐Dimethylformamide (DMF), experimental results show that increasing humidity during spinning causes an increase in fiber diameter and a decrease in mechanical strength. Moreover, surface features such as roughness or pores become evident when electrospinning in an atmosphere with high relative humidity (RH). However, PAN and PSU fibers are affected differently. PAN has a narrower distribution of fiber diameter regardless of the RH, whereas PSU has a wider and more bimodal distribution under high RH. In addition, PSU fibers spun at high humidity exhibit surface pores and higher specific surface area whereas PAN fibers exhibit an increased surface roughness but no visible pores. These fiber morphologies are caused by a complex interaction between the nonsolvent (water), the hygroscopic solvent (DMF), and the polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Solvent and concentration effects on the properties of electrospun poly(ethylene terephthalate) nanofiber mats

This study describes the preparation and characterization of nanofibrous mats obtained by electrospinning poly(ethylene terephthalate) (PET) solutions in trifluoroacetic acid/dichloromethane (TFA/DCM). Special attention was paid to the effect of polymer concentration and solvent properties on the morphology, structure, and mechanical and thermal properties of the electrospun nonwovens. The results show that the spinnable concentration of PET solution in TFA/DCM solvents is above 10 wt %. Mats have nanofibrous morphology with fibers having an average diameter in the range of 200–700 nm (depending on polymer concentration and solvent composition) and an interconnected pore structure. Higher solution concentration favors the formation of uniform fibers without beads and with higher diameter. Morphology and fiber assembly changed with the solvent properties. Solvent mixtures rich in TFA, i.e., those with higher dielectric constant and lower surface tension, originated fibers with small diameter. However, due to the lower volatility, those solvent mixtures also produced more branched and crosslinking fibers, with less morphologic uniformity. Mechanical properties (Young's modulus, ultimate strength, and elongation at break) and thermal properties (glass transition, crystallization, and melting) have been studied for the PET electrospun nanomats and compared with those of the original polymer. Solvent effect on fiber crystallinity was not significant, but a complex effect was observed on the mechanical properties of the electrospun mats, as a consequence of the different structural organization of the fibers within the mat network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 460–471, 2008     

A novel two-nozzle electrospinning process for preparing microfiber reinforced pH-sensitive nano-membrane with enhanced mechanical property

A novel pH sensitive membrane (pHS-M) with mechanical integrity is synthesized firstly by two nozzles electrospining in this work. We report an excellent strategy here to combine indicative nanofiber from 9% PAN solution and micro-sized fibers from 20% PA-66 solution homogeneously in one electrospinning setup. The pH indicative property of electrospun sheet can be achieved by PAN nanofibers that first aminating with ethylenediamine and then immobilizing phenolphthalein covalently through a Mannich reaction, while micro-sized PA-66 fibers are responsible for the improvement of mechanical property of electrospun mat due to their elastic and flexible behavior. The composite membrane was characterized by SEM, FTIR and UV–vis spectroscopy. Results show that two kinds of pH sensitive membranes (single PAN nanofibers (pHS-NF) or composite PAN/PA-66 fiber (pHS-CF)) all exhibited remarkable color change from pale yellow to violet in a wide range of alkaline solution and rapid response time within 100 s. But after added of microfiber, the tensile strength was enhanced from 1.3 MPa to 6.90 MPa prominently which is beneficial to put the membrane into practice.     

Surface modification of coir fibers I: studies on graft copolymerization of methyl methacrylate on to chemically modified coir fibers

Graft copolymerization of methyl methacrylate (MMA) onto chemically modified coir fiber was studied using a CuSO₄–KIO₄ combination as initiator in an aqueous medium in the temperature range of 50–70 °C. Concentrations or [IO₄−] = 0.005 mol/l and [Cu2+] = 0.002 mol/l produce optimum grafting. The effects of time, temperature, amount of coir fiber, some inorganic salts and organic solvents on graft yield have also been investigated. On the basis of experimental findings, a reaction mechanism has been proposed. Evidence of grafting was studied from fourier transform infrared spectroscopy and scanning electron microscopy of chemically modified coir and MMA‐grafted coir. Tensile properties such as maximum stress at break, extension at break and Young's modulus of untreated, defatted, chemically treated and grafted coir fibers were evaluated and compared. Grafted coir fiber showed an increase in tensile properties such as maximum stress at break, extension at break and Young's modulus. Copyright © 1999 John Wiley & Sons, Ltd.     

Electrospun poly(3‐hexylthiophene)/poly(ethylene oxide)/graphene oxide composite nanofibers: effects of graphene oxide reduction

In this article, we report on the production by electrospinning of P3HT/PEO, P3HT/PEO/GO, and P3HT/PEO/rGO nanofibers in which the filler is homogeneously dispersed and parallel oriented along the fibers axis. The effect of nanofillers' presence inside nanofibers and GO reduction was studied, in order to reveal the influence of the new hierarchical structure on the electrical conductivity and mechanical properties. An in‐depth characterization of the purity and regioregularity of the starting P3HT as well as the morphology and chemical structure of GO and rGO was carried out. The morphology of the electrospun nanofibers was examined by both scanning and transmission electron microscopy. The fibrous nanocomposites are also characterized by differential scanning calorimetry to investigate their chemical structure and polymer chains arrangements. Finally, the electrical conductivity of the electrospun fibers and the elastic modulus of the single fibers are evaluated using a four‐point probe method and atomic force microscopy nanoindentation, respectively. The electrospun materials crystallinity as well as the elastic modulus increase with the addition of the nanofillers while the electrical conductivity is positively influenced by the GO reduction. Copyright © 2016 John Wiley & Sons, Ltd.     

Nanostructural evidence of mechanical aging and performance loss in ballistic fibers

It is understood that the ballistic resistance of aromatic polyamide fibers is related to the fiber's ultimate tensile strength, strain‐to‐failure, and Young's modulus. Ideal high‐performance ballistic materials maximize these properties while minimizing material density. Equally important is long‐term mechanical and chemical stability: the fibers should not exhibit performance loss over their lifetime. However, less is known quantitatively about their modes of degradation, and experimental methods to quantify the aging and degradation in these fibers are critical. Multiple variations of next generation high‐performance fibers have been investigated under chemical and mechanical accelerated aging conditions. Performance losses have been empirically correlated to chemical degradation of the polymer chain and nanostructural changes in the fiber morphology through X‐ray photoelectron spectroscopy (XPS). Here, we introduce positron annihilation lifetime spectroscopy measurements as a sensitive method to quantify the early onset of damage in the flexed fibers as quantified through changes in the nanoscale void structure in the material. Published 2017.^? J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1711–1717     

Physical characteristics of Saccharomyces cerevisiae

We examined the physical properties of the surrounding yeast cell walls by using atomic force microscopy (AFM). The yeast cells were prepared on a cleaned glass substrate for confocal microscopy (CM) observation and were mechanically trapped into a porous membrane for AFM measurement. The confocal image of the yeast cells was measured in air, meanwhile the AFM topography images of the cells were measured in both deionized (DI) water (pH = 6.9) and phosphate‐buffered saline (PBS) solution (pH = 7.4). No significant differences between the AFM topography images of the yeast cells measured in DI water and in PBS solution could be inferred. In order to get the quantitative information on the sample elasticity, the force curves between an AFM tip and the yeast cell have been measured. These curves were measured in both DI water and in PBS solution on the same yeast cell using the same AFM cantilever to get the reliable result. The contact region of the force curve in approach mode was then converted into force versus indentation curve, which would be fitted with Hertz–Sneddon model for the calculation of the elasticity. Analysis of the curves indicates that there is a difference of the Young's modulus values of the yeast cell in various environments. These data show that the salt buffer solution increases the rigidity of the biological system. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Biodegradable Poly(ϵ-caprolactone)-b-Poly(L-lactide) and Study on Their Electrospun Scaffolds

A series of multi-block copolymers, poly(L-lactide)-b-poly (?-caprolactone) (PLLA-b-PCL) were synthesized. The first step of the synthesis consisted of the transesterification between the PLLA and 1,4-Butanediol, followed by the copolymerization of PLLA-diols and PCL, using isophorone diisocyanate (IPDI) as a coupling agent. The synthesized polymers were characterized by Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD). PLLA/PCL block copolymers were electrospun into ultrafine fibers. The morphology of the electrospun fibrous scaffolds were investigated by Scanning Electron Microscopy (SEM). Results showed that the morphology and diameter of the fibers were affected by the electrospinning solution concentrationan and different weight ratio of PLLA/PCL. These electrospun PLLA-b-PCL fibrous membranes exhibited good flexibility and deformability. In comparison with the electrospun PLLA membrane, the electrospun fibrous membranes of PLLA-b-PCL demonstrated an enhanced elongation with still high tensile strength and Young's modulus to be beneficial for tissue engineering scaffolds.     

Processing and properties of melt spun polylactide–multiwall carbon nanotube fiber composites

This article reports on the fabrication of oriented composite fibers between polylactide (PLA) and multiwall carbon nanotube (MWNT). The fibers were fabricated using a custom‐built melt fiber‐drawing setup. The influence of processing parameters on the final fiber diameter and on the orientation were characterized and optimized. Composite fibers were fabricated at various MWNT contents. Addition of low amounts of MWNT (0.25–1 wt %) to PLA did not have a significant effect on the diameters of the fibers. Observations of the composite morphology under STEM indicated preferential orientation of the MWNTs along the draw direction of the fibers. Increasing amounts of MWNTs was found to increase crystallization kinetics and content. The crystalline content had a direct and profound implication on the mechanical properties with 0.5‐wt % MWNT fibers having the highest crystalline content and also the highest Young's modulus. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 477–484     

Effects of humidity on Young's modulus in poly(methyl methacrylate)

Tensile tests on poly (methyl methacrylate) (PMMA) were conducted to clarify the effects of humidity and strain rate on tensile properties, particularly Young's modulus. Prior to the tensile tests, specimens were kept under various humidity conditions at 293 K, which were the same as the test conditions, for a few months to adjust the sorbed water content in the specimens. The tensile tests were performed under each humidity condition at three different strain rates (approximately 1.4 × 10^?3, 1.4 × 10^?4, and 1.4 × 10^?5 s^?1). Stress‐strain curves changed with humidity and strain rate. Young's moduli were also measured at small applied stresses (below 6.7 MPa) under various humidity conditions at 293 K. Young's modulus decreases linearly with increasing humidity and a decreasing logarithm of strain rate. These results suggest that Young's modulus of PMMA can be expressed as a function of two independent parameters that are humidity and strain rate. A constitutive equation for Young's modulus of PMMA was proposed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 460–465, 2002; DOI 10.1002/polb.10107     

Preparation of porous ultrafine polyacrylonitrile (PAN) fibers by electrospinning

A facile method for the preparation of porous ultrafine nanofibers was demonstrated. The PAN/NaHCO₃ composite nanofibers were electrospun, and then NaHCO₃ was removed by a selective dissolution and reaction with the solution of hydrochloric acid (10 wt%). The obtained PAN fibers showed highly porous surfaces after the extraction of NaHCO₃. The structure and properties of ultrafine PAN nanofibers were characterized by Fourier transform infrared (FT‐IR), X‐ray diffraction (XRD), and thermogravimetry (TG). The results indicated that NaHCO₃ could be introduced into the PAN solution and successfully electrospun. CO₂ is released and pores are formed on the fibers. The morphology image of the fibers was detected by scanning electron microscope (SEM) and showed that many pores aligned the nanofibers. Copyright © 2008 John Wiley & Sons, Ltd.     

Small‐angle X‐ray scattering investigation of carbon nanotube‐reinforced polyacrylonitrile fibers during deformation

Structural changes during deformation in solution‐ and gel‐spun polyacrylonitrile (PAN) fibers with multi‐ and single‐wall carbon nanotubes (CNTs), and vapor‐grown carbon nanofibers were investigated using synchrotron X‐ray scattering. Previously published wide‐angle X‐ray scattering (WAXS) results showed that CNTs deform under load, alter the response of the PAN matrix to stress, and thus enhance the performance of the composite. In this article, we find that the elongated scattering entities that give rise to the small‐angle X‐ray scattering (SAXS) in solution‐spun fibers are the diffuse matrix‐void interfaces that follow the Porod's law, and in gel‐spun fibers these are similar to fractals. The observed smaller fraction of voids in the gel‐spun fibers accounts for the significant increase in the strength of this fiber. The degree of orientation of the surfaces of the voids is in complete agreement with those of the crystalline domains observed in WAXS, and increases reversibly upon stretching in the same way as those of the crystalline domains indicating that the voids are integral parts of the polymer matrix and are surrounded by the crystalline domains in the fibrils. The solution‐spun composite fibers have a larger fraction of the smaller (<10 nm) voids than the corresponding control PAN fibers. Furthermore, the size distribution of the voids during elongation changes greatly in the solution spun PAN fiber, but not so in its composites. The scattered intensity, and therefore the volume fraction of the voids, decreases considerably above the glass transition temperature (T_g) of polymer. Implications of these observations on the interactions between the nanotubes and the polymer are discussed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2394–2409, 2009