层状水凝胶仿生软骨的制备与性能

采用超声分散、高压加热共融、冷冻-熔融和γ射线辐照交联成型工艺制备层状水凝胶仿生软骨材料, 系统讨论了PVP添加量和辐照剂量对材料的凝胶含量、晶态结构及抗压缩弹性模量的影响, 观察和研究了层状水凝胶的微观结构. 研究结果表明, 随着PVP的质量分数(0-40%)和辐照剂量(0-60 kGy)的增加, 层状水凝胶的凝胶含量呈上升趋势; 其晶态结构在质量分数为20%的PVP和10 kGy辐照剂量下最完善; 其力学性能在质量分数为20%的PVP和20 kGy辐照剂量下最佳; PVP的加入改善了水凝胶的微观形貌, 有利于材料表面润滑性能的提高; 层状水凝胶层间渗透结合, 自然过渡, 形成结构良好的仿生软骨材料.     

用于柔性超级电容器的凝胶聚合物电解质膜的制备

以聚乙烯吡咯烷酮(PVP)提高戊二醛(GA)交联的聚乙烯醇(PVA)凝胶在1 mol/L的H2SO4溶液中的溶胀度,制备出一种用于柔性超级电容器的凝胶聚合物电解质膜,并对该电解质膜的结构、形貌、溶胀度、力学性能和电导率等进行了表征.在此基础上,组装了一种基于石墨烯电极的柔性超级电容器.结果表明:随着PVP用量的增加,膜孔数量增多且孔径增大,溶胀度增加,电导率提高,但力学强度下降.电解质膜中PVP质量分数为20％时,所组装的柔性超级电容器的比电容为111 F/g,其电化学性能的温度依赖性较低,稳定性较好.     

Polydopamine- and polyDOPA-coated electrospun poly(vinyl alcohol) nanofibrous membranes for cationic dye removal

Mussel adhesive proteins including special functional groups, such as dopamine and 3,4-dihydroxy-l-phenylalanine (DOPA), exhibit strong adhesion and have thus been used in numerous applications. As a novel dye adsorbent for wastewater treatment, this study examineed poly(vinyl alcohol) (PVA) nanofibrous membranes (NFMs) fabricated via electrospinning and then coated with polydopamine (pDA) or polyDOPA through a simple dip coating process in dopamine or DOPA solution to examine. The surface morphology, chemical composition and hydrophilicty of PVA NFMs coated with pDA or polyDOPA were compared using scanning electron microscopy (SEM), UV photoelectron spectrometry (XPS) and contact angle analyzer, respectively. The thermal degradation temperatures of the PVA NFMs were increased significantly by about 100 °C due to the radical scavenging ability of pDA and pDOPA. Also, the differences in the adsorption performance toward a cationic dye, methylene blue (MB), for polydopamine- or polyDOPA-coated PVA NFMs were evaluated using a UV–Visible spectrophotometer. Finally, a recyclability test was conducted to confirm the applicability as a dye adsorbent.     

Optimization and characterization of electrospun chitosan/poly(vinyl alcohol) nanofibers as a phenol adsorbent via response surface methodology

Fabrication and characterization of chitosan/poly(vinyl alcohol) electrospun nanofibers for adsorption of phenol from water were investigated. The effects of voltage (15–30 kV), solution injection flow rate (0.5–1.5 ml/hr), distance of needle and collector (10–20 cm) and chitosan/poly(vinyl alcohol) ratio (25/75, 50/50, 75/25) were studied to obtain the optimum electrospinning conditions for the maximum adsorption capacity of phenol. Central composite design (CCD) was used to investigate and optimize the processing factors for production of chitosan/poly(vinyl alcohol) nanofibers from aqueous solutions. The nanofibers were characterized using scanning electron microscopy and Fourier transform infrared spectroscopy (FTIR). Uniform beadless nanofibers with the minimum diameters of 3–11 nm were obtained at chitosan/poly(vinyl alcohol) ratio of 50/50, voltage of 22.5 kV, distance of 15 cm and injection flow rate of 1.99 ml hr^?1. Fourier transform infrared spectrum of chitosan/poly(vinyl alcohol) exhibited the existence of relevant functional groups of both poly(vinyl alcohol) and chitosan in the blends. Results of CCD show that among all processing factors, rate of electrospinning will highly affect the nanofiber adsorption. The response surface quadratic order model presented correlation coefficient explaining 69.5% of the variability in the adsorption. Copyright © 2017 John Wiley & Sons, Ltd.     

Photocrosslinked methacrylated poly(vinyl alcohol)/hydroxyapatite nanocomposite hydrogels with enhanced mechanical strength and cell adhesion

Poly(vinyl alcohol) (PVA) hydrogels with high water content, good load‐bearing property, low frictional behavior as well as excellent biocompatibility have been considered as promising cartilage replacement materials. However, the lack of sufficient mechanical properties and cell adhesion are two critical barriers for their application as cartilage substitutes. To address these problems, herein, methacrylated PVA with low degree of substitution of methacryloyl group has been synthesized first. Then, methacrylated PVA‐glycidyl methacrylate/hydroxyapatite (PVA‐GMA/Hap) nanocomposite hydrogels have been developed by the photopolymerization approach subsequently. Markedly, both pure PVA‐GMA hydrogel and PVA‐GMA/Hap nanocomposite hydrogels exhibit excellent performance in compressive tests, and they are undamaged during compressive stress–strain tests. Moreover, compared to pure PVA‐GMA hydrogels, 8.5‐fold, 7.4‐fold, and 14.2‐fold increase in fracture stress, Young's modulus and toughness, respectively, can be obtained for PVA‐GMA/Hap nanocomposite hydrogels with 10 wt % Hap nanoparticles. These enhancements can be ascribed to the intrinsic property of PVA‐GMA and strong hydrogen bonding interactions between PVA‐GMA chain and Hap nanoparticles. More interestingly, significant improvement in the cell adhesion can also be successfully achieved by incorporation of Hap nanoparticles. These biocompatible nanocomposite hydrogels have great potential to be used as cartilage substitutes. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1882–1889     

Relationships between nanostructure and thermomechanical properties in poly(vinyl alcohol)/montmorillonite nanocomposite with an entrapped polyelectrolyte

Poly(vinyl alcohol)/montmorillonite (PVA/MOM) hydrogels containing coacervated microparticles of sulfonated polyester (PES) were prepared by direct mixture of the components in water. The system was characterized by using differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS), and dynamical mechanical analysis (DMA). The influence of PES and MOM on the microstructure of the nanocomposite hydrogels was established. The presence of PES causes a significant change on the crystallinity of PVA. Furthermore, the presence of MOM leads to a hierarchical nanostructure that also contributes to change the crystallinity of PVA. The results of structural investigation are correlated with the mechanical properties of the composites obtained by DMA. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2618–2629, 2008     

Hyaluronic acid‐poly(vinyl alcohol) composite cryo‐gel for biofunctional material application

Recently, applications of hyaluronic acid (HA) as a biomaterial were investigated. However, the weak structure of HA gel and the effects of using cross‐linker raised concerns during in vivo resolution. In this study, we investigated the method to solve these two problems using physical cross‐linking and compositing with poly(vinyl alcohol) (PVA). Various weight ratios of HA and PVA solutions were mixed, adjustment of pH to 1.8 using HCl then used to fabricate HA‐PVA cryo‐gel by freezing‐thawing. Young's modulus of the prepared gel rose with the increase of both HA and PVA concentrations or either one of them. We estimated that HA and PVA have exhibited these mechanical properties due to forming a double network. HA‐PVA gel showed kinetic friction force of approximately 10 times of PVA gel, while water contact angle and protein adsorption of HA‐PVA gels were remarkably decreased. The properties of the prepared gel suggest that it can be used for postoperative adhesion prevention applications.     

Properties of low temperature swelling hydrogels prepared with partially saponified PVA and drug release using the hydrogels

The hydrogels prepared by the crosslinking of partially saponified poly(vinyl alcohol) (PVA) which has low critical solution temperature (LCST) in water showed characteristics of swelling at low temperature and shrinkage at high temperature. The hydrogels showed repeatable swelling–shrinking behavior. The hydrogels containing release substances such as cyanocobalamin, p‐acetamidophenol, insulin and ovalbumin were prepared by dipping these aqueous solutions and the release substances were studied. Insulin and ovalbumin were not absorbed by the hydrogels when the use of partially PVA with the degrees of polymerization (DPs) of 540 were prepared, but absorbed by the hydrogels with DPs of 1860. The size of the polymer network prepared with a higher DP was suitable for the absorption of insulin and ovalbumin. In accordance with release substances, the release patterns were different. In this way, the polymer network sizes and their swelling behaviors of partially saponified PVAs were estimated. Copyright © 2003 John Wiley & Sons, Ltd.     

Mesoporous Silica Particles as Topologically Crosslinking Fillers for Poly(N‐isopropylacrylamide) Hydrogels

Here it is demonstrated that mesoporous silicas (MPSs) can be used as effective “topological crosslinkers” for poly(N‐isopropylacrylamide) (PNIPA) hydrogels to improve the mechanical property. Three‐dimensional bicontinuous mesporous silica is found to effectively reinforce the PNIPA hydrogels, as compared to nonporous silica and two‐dimensional hexagonally ordered mesoporous silica.     

Photo‐Induced Anomalous Deformation of Poly(N‐Isopropylacrylamide) Gel Hybridized with an Inorganic Nanosheet Liquid Crystal Aligned by Electric Field

Poly‐(N‐isopropylacrylamide) (PNIPA) hydrogel films doped with uniaxially aligned liquid crystalline (LC) nanosheets adsorbed with a dye are synthesized and its anomalous photothermal deformation is demonstrated. The alignment of the nanosheet LC at the cm‐scale is easily achieved by the application of an in‐plane or out‐of‐plane AC electric field during photo‐polymerization. A photoresponsive pattern is printable onto the gel with μm‐scale resolution by adsorption of the dye through a pattern‐holed silicone rubber. When the gel is irradiated with light, only the colored part is photothermally deformed. Interestingly, the photo‐irradiated gel shows temporal expansion along one direction followed by anisotropic shrinkage, which is an anomalous behavior for a conventional PNIPA gel.

     

Gold nanoparticles as structurizing agents for the formation of hybrid nanocomposites

Two types of transparent gold-containing organo-inorganic hybrid gels (polymer nanocomposites) in which gold nanoparticles (nano-Au) are efficient species were synthesized. The stage of hybrid gel formation is preceded by the in situ chemical reduction of chloroauric acid in an aqueous solution of the synthetic linear polymer (polyvinyl alcohol or poly(N-vinylpyrrolidone)) affording a nano-Au. The presence of ultradispersed gold particles in the obtained nanocomposites was confirmed by UV-Vis spectroscopy and electron microscopy. The loss of solubility of the films in water confirms the formation of a gel network. The size of the gold particles and characteristics of the hybrid gel change depending on the molecular weight of the polymer. The interaction of the macromolecules and growing particles mainly determines the diameter and number of particles of the inorganic phase, whereas the content of chloroauric acid affects these parameters to a less extent. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 329–336, February, 2008.     

Novel materials for bioanalytical and biomedical applications: Environmental response and binding/release capabilities of amphiphilic hydrogels with shape‐persistent dendritic junctions

The binding and release capabilities of a hydrogel series, constructed of hydrophilic poly(ethylene glycol) segments and hydrophobic dendritic junctions [poly (benzyl ether)s], are evaluated in aqueous media. The environmental response of the amphiphilic networks is also tested in water at three pH values: 1.5, 7.0, and 10.1. The highest swelling ratio is observed under acidic conditions and varies between 3.7 and 6.5, depending on the crosslinking density and dendrimer generation. Gel specimens with embedded indicators react within 3–6 s with a clear color switch to the change in the pH of the surrounding medium. The experiments with model anionic and cationic indicators and stains show that the hydrogels have basic interiors. The gel binding capabilities depend on the water solubility of the substrate and on the size of the incorporated dendritic fragments. Model release studies have been performed at 37 °C and pHs 1.5, 7.0, and 10.1. The observed phenomena are explained by the transformations in the structure and charge that both the networks and the model compounds undergo with the changes in the pH of the aqueous medium. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4017–4029, 2005     

Nanoporous silica polyamine composites for metal ion capture from rice hull ash

Rice hull ash (RHA) was converted to amorphous silica gel using a modified version of published literature procedures. The gels were characterized by a comparison of their Cross Polarization Magic Angle Spinning ²⁹Si NMR and scanning electron microscopy images with commercial silica gels. The resulting gels were silanized with a 7.5:1 mixture of methyltrichlorosilane and chloropropyltrichlorosilane and then reacted with poly(allylamine) (PAA) to produce the silica polyamine composite (SPC) BP‐1. The BP‐1 was then further modified with pyridine‐2‐carboxaldehyde to form the copper‐selective SPC, CuSelect. This procedure follows that used to produce the commercialized version of these composite materials from commercially available amorphous silica gels. The composites were characterized by solid‐state NMR techniques, elemental analysis, SEM, porosimetry and metal ion capacity and selectivity. The overall goal of the project was to determine the feasibility of using RHA to make SPC. The observed strengths and weaknesses of this approach are discussed. Copyright © 2011 John Wiley & Sons, Ltd.     

Fe2O3-MWNTs Composite with Reinforced Concrete Structure as High-performance Anode Material for Lithium-ion Batteries

AFe₂O₃-MWNTs(multi-walled carbon nanotubes) composite with a reinforced concrete structure was fabricated employing a two-step method, which involves a sol-gel process followed by high-temperature in situ sintering. This Fe₂O₃-MWNTs composite, intended to be used as an anode material for lithium-ion batteries, maintained a reversible capacity as high as 896.3 mA·h/g after 100 cycles at a current density of 100 mA/g and the initial coulombic efficiency reached 75.5%. The rate capabilities of the Fe₂O₃-MWNTs composite, evaluated using the ratios of capacity at 100, 200, 500, 1000, 2000 and 100 mA/g after every 10 cycles, were determined to be 904.7, 852.1, 759.0, 653.8, 566.8 and 866.3 mA·h/g, respectively. Such a superior electrochemical performance of the Fe₂O₃-MWNTs composite is mainly attributed to the reinforced concrete construction, in which the MWNTs function as the skeleton and conductive network. Such a structure contributes to shortening the transport pathways for both Li⁺ and electrons, enhancing conductivity and accommodating volume expansion during prolonged cycling. This Fe₂O₃-MWNTs composite with the designed structure is a promising anode material for high-performance lithium-ion batteries.     

Composite of P(VDF‐CTFE) and aromatic polythiourea for capacitors with high‐capacity,high‐efficiency,and fast response

For next generation of miniaturized personal electronics and pulsed power systems for smart power grids, electric vehicles, and electromagnetic launchers, flexible capacitors from dielectric polymers with high‐capacity, high‐efficiency, and fast response are highly desirable. Dielectric polymer composite of P(VDF‐CTFE), that is poly(vinylidene fluoride‐chlorotrifluoroethylene) and a small amount of aromatic polythiourea (PTU) has been described. It combines the merits of both polymers, that is high dipole density and easy processability of P(VDF‐CTFE), as well as large dipole moment and high charge–discharge efficiency of PTU. Most impressively, PTU boosts the maximum breakdown strength of P(VDF‐CTFE), and thus extracts its maximum energy reserve capacity. PTU also contributes to the promoted charge–discharge efficiency, accelerated discharge, and reduced dielectric loss in P(VDF‐CTFE), which facilitate the composite for flexible capacitor applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 193–199     

Core‐shell microspheres with surface grafted poly(vinyl alcohol) as drug carriers for the treatment of hepatocellular carcinoma

Core(polyvinyl neodecanoate‐ethylene glycol dimethacrylate)‐shell(polyvinyl alcohol) (core (P(VND‐EGDMA))‐shell(PVA)) microspheres were developed by seeded polymerization with the use of conventional free radical and RAFT/MADIX mediated polymerization. Poly(vinyl pivalate) PVPi was grafted onto microspheres prepared via suspension polymerization of vinylneodecanoate and ethylene glycol dimethacrylate. The amount of grafted polymer was found to be independent from the technique used with conventional free radical polymerization and MADIX polymerization resulting into similar shell thicknesses. Both systems—grafting via free radical polymerization or the MADIX process—were found to follow slightly different kinetics. While the free radical polymerization resulted in a weight gain linear with the monomer consumption in solution the growth in the MADIX controlled system experienced a delay. The core‐shell microspheres were obtained by hydrolysis of the poly(vinyl pivalate) surface grafted brushes to form poly(vinyl alcohol). During hydrolysis the microspheres lost a significant amount of weight, consistent with the hydrolysis of 40–70% of all VPi units. Drug loading was found to be independent of the shell layer thickness, suggesting that the drug loading is governed by the amount of bulk material. The shell layer does not appear to represent an obstacle to the drug ingress. Cell testing using colorectal cancer cell lines HT 29 confirm the biocompatibility of the empty microspheres whereas the clofazimine loaded particles lead to 50% cell death, confirming the release of the drug. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3256–3272, 2007     

Molecularly engineered graphene surfaces for sensing applications: A review

Graphene is scientifically and commercially important because of its unique molecular structure which is monoatomic in thickness, rigorously two-dimensional and highly conjugated. Consequently, graphene exhibits exceptional electrical, optical, thermal and mechanical properties. Herein, we critically discuss the surface modification of graphene, the specific advantages that graphene-based materials can provide over other materials in sensor research and their related chemical and electrochemical properties. Furthermore, we describe the latest developments in the use of these materials for sensing technology, including chemical sensors and biosensors and their applications in security, environmental safety and diseases detection and diagnosis.