Synthesis and characterization of a novel AB2 monomer and corresponding hyperbranched poly(arylene ether phosphine oxide)s

A novel AB₂ monomer, 4‐(fluorophenyl)‐4′,4″‐(bishydroxyphenyl) phosphine oxide, was synthesized. The monomer was successfully polymerized to a modest molecular weight with various catalysts, including K₂CO₃ and Cs₂CO₃/Mg(OH)₂. Hyperbranched polymers exhibited exceptionally high thermal stability and solubility in conventional polar organic solvents and basic water solutions. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3736–3741, 2000     

Synthesis and properties of a phosphorus-containing flame retardant epoxy resin based on bis-phenoxy (3-hydroxy) phenyl phosphine oxide

A reactive phosphorus-containing compound, bis-phenoxy (3-hydroxy) phenyl phosphine oxide (BPHPPO) was first successfully synthesized to produce the phosphorus-containing flame retardant epoxy resin (BPHPPO-EP). The chemical structures were characterized from FTIR, MS, NMR spectra and elemental analyses. Thermal degradation behaviors and flame retardant properties of the cured epoxy resins were investigated from the thermogravimetric analysis (TGA) and the limiting oxygen index (LOI) test using 4,4′-diaminodiphenylsulfone (DDS) as curing agent. The high char yields and the high limiting oxygen index values were found to certify the great flame retardancy of this phosphorus-containing epoxy resin.     

Poly(lactic acid) nanocomposites with various organoclays. I. Thermomechanical properties,morphology, and gas permeability

The thermomechanical properties, morphology, and gas permeability of hybrids prepared with three types of organoclays were compared in detail. Hexadecylamine–montmorillonite (C₁₆–MMT), dodecyltrimethyl ammonium bromide–montmorillonite (DTA‐MMT), and Cloisite 25A were used as organoclays in the preparation of nanocomposites. From morphological studies using transmission electron microscopy, most clay layers were found to be dispersed homogeneously in the matrix polymer, although some clusters or agglomerated particles were also detected. The initial degradation temperature (at a 2% weight loss) of the poly(lactic acid) (PLA) hybrid films with C₁₆–MMT and Cloisite 25A decreased linearly with an increasing amount of organoclay. For hybrid films, the tensile properties initially increased but then decreased with the introduction of more of the inorganic phase. The O₂ permeability values for all the hybrids for clay loadings up to 10 wt % were less than half the corresponding values for pure PLA, regardless of the organoclay. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 94–103, 2003     

PLGA-PVA-PEG Single Emulsion Method as a Candidate for Aminolevulinic Acid (5-ALA) Encapsulation: Laboratory Scaling Up and Stability Evaluation

One of the most widely used molecules used for photodynamic therapy (PDT) is 5-aminolevulinic acid (5-ALA), a precursor in the synthesis of tetrapyrroles such as chlorophyll and heme. The 5-ALA skin permeation is considerably reduced due to its hydrophilic characteristics, decreasing its local bioavailability and therapeutic effect. For this reason, five different systems containing polymeric particles of poly [D, L–lactic–co–glycolic acid (PLGA)] were developed to encapsulate 5-ALA based on single and double emulsions methodology. All systems were standardized (according to the volume of reagents and mass of pharmaceutical ingredients) and compared in terms of laboratory scaling up, particle formation and stability over time. UV-VIS spectroscopy revealed that particle absorption/adsorption of 5-ALA was dependent on the method of synthesis. Different size distribution was observed by DLS and NTA techniques, revealing that 5-ALA increased the particle size. The contact angle evaluation showed that the system hydrophobicity was dependent on the surfactant and the 5-ALA contribution. The FTIR results indicated that the type of emulsion influenced the particle formation, as well as allowing PEG functionalization and interaction with 5-ALA. According to the ¹H-NMR results, the 5-ALA reduced the T1 values of polyvinyl alcohol (PVA) and PLGA in the double emulsion systems due to the decrease in molecular packing in the hydrophobic region. The results indicated that the system formed by single emulsion containing the combination PVA–PEG presented greater stability with less influence from 5-ALA. This system is a promising candidate to successfully encapsulate 5-ALA and achieve good performance and specificity for in vitro skin cancer treatment.     

Characterization of an antimicrobial poly(lactic acid) film prepared with poly(ε‐caprolactone) and thymol for active packaging

Antimicrobial active films based on poly(lactic acid) (PLA) were prepared with poly(ε‐caprolactone) (PCL) and thymol (0, 3, 6, 9, and 12 wt%) by solvent casting methods. The films were characterized by thermal, structural, mechanical, gas barrier, and antimicrobial properties. Scanning electron microscopy analysis revealed that the surface of film became rougher with certain porosity when thymol was incorporated into the PLA/PCL blends. Thymol acted as plasticizers, which reduce the intermolecular forces of polymer chains, thus improving the flexibility and extensibility of the films. The addition of PCL into the pure PLA film decreased the glass transition temperature of the films. The presence of thymol decreased the crystallinity of PLA phase, but did not affect the thermal stability of films. Water vapor barrier properties of films slightly decreased with the increase of thymol loading. The antimicrobial properties of thymol containing films showed a significant activity against Escherichia coli and Listeria monocytogenes. The results indicated the potential of PLA/PCL/thymol composites for applications in antimicrobial packaging. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of poly(vinyl alcohol) fine particles as a novel biodegradable nucleating agent on the crystallization of poly(3‐hydroxybutyrate)

The effect of poly(vinyl alcohol)(PVA) fine particles as the nucleating agent on the crystallization behavior of bacterial poly(3‐hydroxybutyrate)(PHB) was studied using differential scanning calorimetry measurements and polarized light microscope observation. The results were compared with the effect of PVA conventionally blended with PHB. The PVA fine particles were found to be able to greatly enhance the crystallization of PHB, while the conventionally blended PVA extremely retarded the crystallization of PHB. The nucleating effect of PVA fine particles is almost comparable to that of the talc powder. Considering the biodegradability and biocompatibility of PVA, the usage of PVA particle as a nucleating agent provides marked benefits over the currently employed nonbiodegradable nucleating agents, such as talc and boron nitride. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44:1813–1820, 2006     

Poly(ethylene glycol)-b-poly(1,3-trimethylene carbonate) Amphiphilic Copolymers for Long-Acting Injectables: Synthesis,Non-Acylating Performance and In Vivo Degradation

This article presents the evaluation of diblock and triblock poly(ethylene glycol)-b-poly(1,3-trimethylene carbonate) amphiphilic copolymers (PEG-PTMCs) as excipients for the formulation of long-acting injectables (LAIs). Copolymers were successfully synthesised through bulk ring-opening polymerisation. The concomitant formation of PTMC homopolymer could not be avoided irrespective of the catalyst amount, but the by-product could easily be removed by gel chromatography. Pure PEG-PTMCs undergo faster erosion in vivo than their corresponding homopolymer. Furthermore, these copolymers show outstanding stability compared to their polyester analogues when formulated with amine-containing reactive drugs, which makes them particularly suitable as LAIs for the sustained release of drugs susceptible to acylation.     

Block–Stereoblock Copolymers of Poly(ϵ‐Caprolactone) and Poly(Lactic Acid)

A magnesium complex of the type {ONNN}Mg‐HMDS wherein {ONNN} is a sequential tetradentate monoanionic ligand is introduced. In the presence of an alcohol initiator this complex catalyzes the living and immortal homopolymerization of the lactide enantiomers and ?‐caprolactone at room‐temperature with exceptionally high activities, as well as the precise block copolymerization of these monomers in a one‐pot synthesis by sequential monomer addition. Copolymers of unprecedented microstructures such as the PCL‐b‐PLLA‐b‐PDLA and PDLA‐b‐PLLA‐b‐PCL‐b‐PLLA‐b‐PDLA block–stereoblock microstructures that feature unique thermal properties are readily accessed.     

表面响应曲面法优化微生物中聚β-羟基丁酸酯提取条件的研究

利用表面响应曲面法(RSM)优化次氯酸钠/氯仿混合溶液提取微生物体内聚β-羟基丁酸酯(PHB)的过程,选取了次氯酸钠的百分含量、反应时间、反应温度以及混合液中次氯酸钠与氯仿不同比例为因子,以PHB/MLSS为响应因子。实验结果表明提取的最佳条件是NaClO为13%、反应温度为45℃、反应时间为2.8h,NaClO∶CHCl3(V/V)为1.3。利用最佳操作条件,提取出来的产量可以提高25%。     

A new rhodium complex with a nitrogen‐containing bis(phosphine oxide) ligand as an efficient catalyst for the hydroformylation of styrene

A new rhodium complex with a nitrogen‐containing bis(phosphine oxide) ligand has been synthesized. The complex was applied to hydroformylation of styrene and displayed high activity and regioselectivity towards the branched aldehyde, which was found to be higher than those of the tertiary bis(phosphine) analogue. Copyright © 2006 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Preparation and characterization of biodegradable poly(lactic acid)‐ block‐poly(ε‐caprolactone) multiblock copolymer

Biodegradable copolymers of poly(lactic acid)‐block‐poly(ε‐caprolactone) (PLA‐b‐PCL) were successfully prepared by two steps. In the first step, lactic acid monomer is oligomerized to low molecular weight prepolymer and copolymerized with the (ε‐caprolactone) diol to prepolymer, and then the molecular weight is raised by joining prepolymer chains together using 1,6‐hexamethylene diisocyanate (HDI) as the chain extender. The polymer was carefully characterized by using ¹H‐NMR analysis, gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR). The results of ¹H‐NMR and TGA indicate PLA‐b‐PCL prepolymer with number average molecular weights (M_n) of 4000–6000 were obtained. When PCL‐diols are 10 wt%, copolymer is better for chain extension reaction to obtain the polymer with high molecular weight. After chain extension, the weight average molecular weight can reach 250,000 g/mol, as determined by GPC, when the molar ratio of –NCO to –OH was 3:1. DSC curve showed that the degree of crystallization of PLA–PCL copolymer was low, even became amorphous after chain extended reaction. The product exhibits superior mechanical properties with elongation at break above 297% that is much higher than that of PLA chain extended products. Copyright © 2009 John Wiley & Sons, Ltd.     

Developing a novel alkaline anion exchange membrane derived from poly(ether‐imide) for improved ionic conductivity

We have developed a novel alkaline anion exchange membrane derived from poly(ether‐imide) for improved ionic conductivity. The effects of several important parameters on the chloromethylation of the membrane were investigated. These parameters included reaction temperature, reaction time, concentration of chloromethylation agent, concentration of polymer, and the amount of catalyst. The quaternization of the synthesized chloromethylated polymer was studied as well. The results show that all the studied parameters exhibited significant impacts on chloromethylation. Among them, the concentration of the chloromethylation agent played a key role in increasing the chloromethyl functional group attachment onto the polymer. It was found that the gelation could be avoided if these reaction parameters were controlled. It was also found that using an appropriate quaternization approach could significantly improve the ionic conductivity and optimize the conductivity of the membrane even though the functional chloromethyl groups attached to the polymer are limited. Copyright © 2009 John Wiley & Sons, Ltd.     

Stereocomplex poly(lactic acid) vascular stents by 3D‐printing with long chain branching structures: Toward desirable crystallization properties and mechanical performance

Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t_1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities.     

Fluorescence lifetime of terbium(III) as a probe for the ion-binding properties of tactic poly(methacrylic acids)

The binding properties of trivalent metal ions to polyelectrolytes were investigated through the use of terbium [Tb(III)] in fluorescence studies. The fluorescence intensity and lifetimes of the lanthanide ions are directly dependent upon the number of water molecules bound to their inner coordination sphere. The more efficiently a ligand coordinates to a lanthanide ion, the more water molecules are expelled and consequently, the greater the fluorescence intensity and lifetime. This effect was used to probe for differences in the complexation behavior of tactic polymers. Aqueous solutions of isotactic and syndiotactic poly(methacrylic acid) (PMA) were neutralized and complexed with Tb(III) ions. The fluorescence intensity of the 286 nm hypersensitive excitation band was monitored and the lifetimes were measured using several excitation wavelengths. It was found that the isotactic PMA/Tb(III) complex exhibited a six times greater fluorescence intensity than the syndiotactic PMA complex. Lifetime measurements gave the number of water molecules coordinated by Tb(III) in the isotactic complex to be 2.4 while 3.4 waters remained bound to the Tb(III) ion in the syndiotactic PMA complex. These results indicate that isotactic PMA has the greater binding affinity towards Tb(III) ions. © 1997 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(4-vinylpyridine) substituted with a novel betaine salt derived from 4,5-dicyanoimidazole

A novel betaine internal salt ( 3 ) has been synthesized by the reaction of pyridine with 1-methyl-2-bromo-4,5-dicyanoimidazole ( 1 ). The reaction of pyridine with 1 serves as a model for the reaction of poly(4-vinylpyridine) with 1 . The reaction of poly(4-vinylpyridine) with 1 gives betaine salt substituted polymers which were characterized by IR, NMR, UV-visible spectroscopy, and viscometry. The substituted polymers were compared to the model compound ( 3 ) and to unsubstituted poly(4-vinylpyridine) in order to determine polymer structure and the degree of substitution. One of the substituted polymers shows polyelectrolyte behavior. Thermal characterization of the substituted polymers shows two exothermic transitions at 260 and 340°C attributed to chemical reactions of the pendant groups.     

Non‐isothermal crystallization kinetics and spherulitic morphology of nucleated poly(lactic acid): effect of dilithium cis‐4‐cyclohexene‐1,2‐dicarboxylate as a novel and efficient nucleating agent

The effect of dilithium cis‐4‐cyclohexene‐1,2‐dicarboxylate (CHDA‐Li) as a novel and efficient nucleating agent on the crystallization behaviors and spherulitic morphology of poly(lactic acid) (PLA) as well as non‐isothermal crystallization kinetics of the nucleated PLA was studied by means of differential scanning calorimetry and polarized light microscopy. The results show that CHDA‐Li serves as a good nucleating agent to accelerate the crystallization rate of PLA. The nucleation ability of CHDA‐Li is superior to octamethylenedicarboxylic dibenzoylhydrazide. With the incorporation of CHDA‐Li, the number of the spherulites increases, and the size decreases significantly. The non‐isothermal crystallization kinetics of the nucleated PLA can be well described by Jeziorny's and Mo's models. The activation energies (ΔE) of non‐isothermal crystallization were calculated by Kissinger's and Friedman's methods. The crystallization rate of PLA/0.5 wt% CHDA‐Li sample is faster than that of PLA/0.2 wt% CHDA‐Li sample, while the ΔE of the former is lower than that of the latter. Copyright © 2015 John Wiley & Sons, Ltd.     

Removal of heavy metal ions from aqueous solutions by filtration with a novel complexing membrane containing poly(ethyleneimine) in a poly(vinyl alcohol) matrix

A novel complexing membrane was used for the removal of heavy metal ions such as Pb(II), Cd(II) and Cu(II) from aqueous solutions. The membrane consists in a semi-interpenetrating polymer network of crosslinked poly(vinyl alcohol) as the matrix and poly(ethyleneimine) as the complexing polymer. The absorption reactions followed pseudo-first-order kinetics with similar rate constants for the three cations. A model is proposed for the absorption–desorption process in order to rationalize the data obtained for the retention ratio and the retention efficiency ratio. The corresponding equilibrium constants were determined for the three metal ions, showing that the affinity order of the membrane is Pb > Cu > Cd. This sequence is consistent with the order of maximum uptake of the ions per gram of membrane: 0.59, 0.47 and 0.33 mmol g⁻¹, respectively. On the other hand, the uptake order is different on a mass basis: 123, 30 and 37 mg g⁻¹, respectively. Regeneration of the membrane and metal recovery were studied with HCl and HNO₃ at different concentrations. Filtration of solutions of each metal ion showed large elimination ratios (96–99.5%) with a retention sequence Cd > Cu > Pb. The membrane remained efficient until complete saturation of its sites. Moreover, Cu retention is larger than expected, indicating possible additional chelation by the PVA matrix. Better retention ratios were observed when the concentration of the feed solution was kept constant. Filtration of a mixture of the three cations (all at 100 ppm concentration) resulted in the same retention sequence, but the elimination ratios were smaller and Pb was eventually displaced by Cu and Cd that were present in larger molar concentrations.     

高分子负载Yb(NTf2)3催化酯化及硝化反应

高分子负载Yb(NTf2)3催化酯化及硝化反应;高分子负载;Lewis酸催化;酯化;硝化