首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
The atomic force microscope (AFM) has been used to measure surface forces between silicon nitride AFM tips and individual nanoparticles deposited on substrates in 10(-4) and 10(-2) M KCl solutions. Silica nanoparticles (10 nm diameter) were deposited on an alumina substrate and alumina particles (5 to 80 nm diameter) were deposited on a mica substrate using aqueous suspensions. Ionic concentrations and pH were used to manage attractive substrate-particle electrostatic forces. The AFM tip was located on deposited nanoparticles using an operator controlled offset to achieve stepwise tip movements. Nanoparticles were found to have a negligible effect on long-range tip-substrate interactions, however, the forces between the tip and nanoparticle were detectable at small separations. Exponentially increasing short-range repulsive forces, attributed to the hydration forces, were observed for silica nanoparticles. The effective range of hydration forces was found to be 2-3 nm with the decay length of 0.8-1.3 nm. These parameters are in a good agreement with the results reported for macroscopic surfaces of silica obtained using the surface force apparatus suggesting that hydration forces for the silica nanoparticles are similar to those for flat silica surfaces. Hydration forces were not observed for either alumina substrates or alumina nanoparticles in both 10(-4) M KCl solution at pH 6.5 and 10(-2) M KCl at pH 10.2. Instead, strong attractive forces between the silicon nitride tip and the alumina (nanoparticles and substrate) were observed.  相似文献   

2.
Interaction forces and adhesion between a silica sphere and a flat silica surface in aqueous electrolyte solutions were investigated by atomic force microscopy. The forces were measured as a function of surface separation, pH and NaCl concentration as the surfaces were approaching each other. The adhesion force was determined upon retraction with respect to pH, NaCl concentration and contact time. The magnitude of the long range repulsive force was decreasing with decreasing pH. A short range repulsive force was observed at pH = 2, but no long range repulsive forces were observed at this pH. Force measurements showed that adhesion of silica surfaces in water was obstructed by short and long range repulsive forces. Adhesion was enhanced when both the long and the short range repulsive force was mitigated. A maximum adhesion force of 7.8 mN/m was measured at pH = 12.5 when the short range force vanished and the long range repulsive force was reduced by increasing the NaCl concentration. At pH = 12.5, the work of adhesion was calculated to be 1.2 mJ/m2 according to the Derjaguin–Muller–Toporov (DMT) model. Adhesion energy was much less at pH = 2 (0.3 mJ/m2) due to persistive short range repulsion.  相似文献   

3.
Direct measurements of the interaction forces between a spherical silica particle and a small air bubble have been conducted in aqueous electrolyte solutions by using an atomic force microscope (AFM). The silica particle was hydrophobized with a silanating reagent, and the interaction forces were measured by using several particles with different surface hydrophobicities. In the measured force curves, a repulsive force was observed at large separation distances as the particle moved towards the bubble. The origin of the repulsive force was attributed to an electrostatic double-layer force because both the particle and bubble were negatively charged. After the repulsive force, an extremely long-range attractive force acted between the surfaces. These results indicate that the intervening thin water film between the particle and bubble rapidly collapsed, resulting in the particle penetrating the bubble.

The instability of the thin water film between the surfaces suggests the existence of an additional attractive force. By comparing the repulsive forces of the obtained force curves with the DLVO theory, the rupture thickness was estimated. The hydrophobicity of the particle did not significantly change the rupture thickness, whereas the pH of the solution is considered to be a critical factor.  相似文献   


4.
We introduce a new method for the stabilization of colloidal particles via the synthesis and adsorption of unnatural proteins. Biosynthesis of protein-based polymers offers the advantages of preparation of complex sequences through control of the primary sequence, monodisperse polymers, ease of combinatorial search for anchor blocks, environmentally friendly synthesis, use of water as the solvent, and incorporation of a palette of known natural proteins. We have synthesized an unnatural protein with the sequence thioredoxin-Pro(39)Glu(10) for modification of the forces between alumina particles. The polyglutamate sequence, Glu(10), is anionic (pH > 3) and is designed to anchor the protein to positively charged solids, e.g. alumina in water (pH < 9). The polyproline sequence, Pro(39), is neutral. The thioredoxin is a recombinant form of the natural globular protein with a histidine patch (His-patch-thioredoxin) and is zwitterionic. The combined thioredoxin-Pro(39) sequence is hydrophilic with pI approximately 6.3. This block is designed to remain in solution, thereby providing a steric barrier to the approach of two particles in a range of salt and pH conditions. Ellipsometry experiments show that thioredoxin-Pro(39)Glu(10) does adsorb to alumina. Force measurements with the atomic force microscopy (AFM) colloid probe technique show that adsorption of thioredoxin-Pro(39)Glu(10) leads to repulsive forces that decay exponentially with the separation between the surfaces and are independent of salt concentration in the range 0.001-0.1 M KNO(3). This demonstrates that the repulsive forces are not electrostatic. We hypothesize that the repulsion is due to confinement and loss of solvent for the adsorbed polymer; the forces are similar to those expected for a polymer brush. Force measurements between thioredoxin-coated alumina surfaces also show a repulsive force, but the force has a decay length that is consistent with electrostatic double-layer forces: the thioredoxin has not neutralized the surface charge of the underlying alumina. Our results point to interesting future experiments where recombinant DNA technology could be used to synthesize fusion proteins containing useful natural proteins and an anchor. This may allow preparation, via single-step aqueous self-assembly, of anchored proteins that maintain their natural structure. Our technique is not limited to homopolymer blocks; more complex primary sequences can be used.  相似文献   

5.
The surface charging properties of polycrystalline α-alumina fibres in aqueous electrolyte solutions have been investigated by direct force and streaming potential measurements. The presence of both Al and Si on the surface of the fibres resulted in a chemically heterogeneous surface. The heterogeneous distribution of Si resulted in large attractive forces between the fibres at moderate to low pH values and a pzc/iep at a pH value of approximately 5.5. The origin of this force was electrostatic in nature as the force profiles were well described by the DLVO theory of colloid stability. The agreement between the direct force and streaming potential measurements was good both in terms of the magnitude of the potentials and the position of the pzc/iep. By acid washing the fibres the chemical heterogeneity of the surface was reduced and the attractive force profiles at lower pH values were not observed. Instead repulsive forces were observed which were well described by DLVO theory at all separation distances greater than 8 nm. At smaller separation distances an additional repulsive force was measured which was attributed to the presence of a Al(OH)3 like layer on the surface of the alumina. The acid washing treatment also resulted in a shift in the pH at which the pzc/iep occurred to a value of 6.5, presumably due to a lower surface silica concentration.  相似文献   

6.
Ionic strength dependence of interaction and friction forces between hydrophilic alpha-alumina particles and c-sapphire surfaces (0001) were investigated under basic pH conditions using the colloidal probe method. The compression of the double layer could be seen from force-distance curves as the ionic strength of the solution increased. The forces were repulsive at all ionic strengths measured, even though the interaction distance changed drastically. No jump to contact occurred. The interaction distance decreased from about 20 nm in 10(-3) M KCl solution to about 7 nm in the 1 M KCl case. The lubricating effect of hydrated cations on the lateral friction force was demonstrated at high electrolyte concentrations. This was attributed to more hydrated cations being present in the solution. The friction behavior was closely related to the short-range repulsive forces between the alpha-alumina surfaces at pH 11.  相似文献   

7.
孙静  高濂 《化学学报》2001,59(5):780-783
利用原子显微镜研究NaCl介质浓度及体pH值对氧化铝表面作用力的影响规律。发现较低的盐浓度下,相互作用表示为长程排斥力,双电层厚度的实际值与理论值较好地吻合,随NaCl介质浓度的提高,双电层压缩长程斥力减弱,测定了pHMH4.0变化到9.67的作用力曲线,发现当pH等于7/90时,两表面的相互作用表现为吸引力,通过恒电荷、恒电位拟合,发现氧化铝的等电点在pH8.2处,与Zeta电位的测定结果相一致。  相似文献   

8.
We have investigated the DLVO surface forces of oxidized tungsten and cobalt surfaces using the atomic force microscope (AFM) colloidal probe technique. It was shown by X-ray photoelectron spectroscopy (XPS) and electrokinetic measurements that this model system is representative of industrial tungsten carbide (WC) and cobalt powders used in the production of hard metals. We found that the attractive van der Waals forces are well described by Hamaker constants, calculated from optical data for WO(3) and CoOOH. The repulsive electrostatic double layer forces between WO(3) surfaces increase with increasing pH due to an increasingly negative surface potential. This surface potential decreases with increasing ionic strength at pH 7.5. The electrostatic interaction between WO(3) and CoOOH is attractive at pH 10, suggesting a positively charged CoOOH surface.  相似文献   

9.
The dispersion and gelation of clay suspensions have major impact on a number of industries, such as ceramic and composite materials processing, paper making, cement production, and consumer product formulation. To fundamentally understand controlling mechanisms of clay dispersion and gelation, it is necessary to study anisotropic surface charge properties and colloidal interactions of clay particles. In this study, a colloidal probe technique was employed to study the interaction forces between a silica probe and clay basal plane/edge surfaces. A muscovite mica was used as a representative of 2:1 phyllosilicate clay minerals. The muscovite basal plane was prepared by cleavage, while the edge surface was obtained by a microtome cutting technique. Direct force measurements demonstrated the anisotropic surface charge properties of the basal plane and edge surface. For the basal plane, the long-range forces were monotonically repulsive within pH 6-10 and the measured forces were pH-independent, thereby confirming that clay basal planes have permanent surface charge from isomorphic substitution of lattice elements. The measured interaction forces were fitted well with the classical DLVO theory. The surface potentials of muscovite basal plane derived from the measured force profiles were in good agreement with those reported in the literature. In the case of edge surfaces, the measured forces were monotonically repulsive at pH 10, decreasing with pH, and changed to be attractive at pH 5.6, strongly suggesting that the charge on the clay edge surfaces is pH-dependent. The measured force profiles could not be reasonably fitted with the classical DLVO theory, even with very small surface potential values, unless the surface roughness was considered. The surface element integration (SEI) method was used to calculate the DLVO forces to account for the surface roughness. The surface potentials of the muscovite edges were derived by fitting the measured force profiles with the surface element integrated DLVO model. The point of zero charge of the muscovite edge surface was estimated to be pH 7-8.  相似文献   

10.
Colloidal forces between bitumen surfaces in aqueous solutions were measured with an atomic force microscope (AFM). The results showed a significant impact of solution pH, salinity, calcium and montmorillonite clay addition on both long-range (non-contact) and adhesion (pull-off) forces. Weaker long-range repulsive forces were observed under conditions of lower solution pH, higher salinity and higher calcium concentration. Lower solution pH, salinity and calcium concentration resulted in a stronger adhesion forces. The addition of montmorillonite clays increased long-range repulsive forces and decreased adhesion forces, particularly when co-added with calcium ions. The measured force profiles were fitted with extended DLVO theory to show the repulsive electrostatic double layer and attractive hydrophobic forces being the dominant components in the long-range forces between the bitumen surfaces. At a very short separation distance (less than 4–6 nm), a strong repulsion of steric origin was observed. The findings provide a fundamental understanding of bitumen emulsion stability and a mechanism of bitumen “aeration” in bitumen recovery processes from oil sands.  相似文献   

11.
A combined theoretical and experimental study of the adhesion of alumina particles and polystyrene latex spheres to silicon dioxide surfaces was performed. A boundary element technique was used to model electrostatic interactions between micron-scale particles and planar surfaces when the particles and surfaces were in contact. This method allows quantitative evaluation of the effects of particle geometry and surface roughness on the electrostatic interaction. The electrostatic interactions are combined with a previously developed model for van der Waals forces in particle adhesion. The combined model accounts for the effects of particle and substrate geometry, surface roughness and asperity deformation on the adhesion force. Predictions from the combined model are compared with experimental measurements made with an atomic force microscope. Measurements are made in aqueous solutions of varying ionic strength and solution pH. While van der Waals forces are generally dominant when particles are in contact with surfaces, results obtained here indicate that electrostatic interactions contribute to the overall adhesion force in certain cases. Specifically, alumina particles with complex geometries were found to adhere to surfaces due to both electrostatic and van der Waals interactions, while polystyrene latex spheres were not affected by electrostatic forces when in contact with various surfaces.  相似文献   

12.
Silica is a very interesting system that has been thoroughly studied in the last decades. One of the most outstanding characteristics of silica suspensions is their stability in solutions at high salt concentrations. In addition to that, measurements of direct-interaction forces between silica surfaces, obtained by different authors by means of surface force apparatus or atomic force microscope (AFM), reveal the existence of a strong repulsive interaction at short distances (below 2 nm) that decays exponentially. These results cannot be explained in terms of the classical Derjaguin, Landau, Verwey, and Overbeek (DLVO) theory, which only considers two types of forces: the electrical double-layer repulsion and the London-van der Waals attraction. Although there is a controversy about the origin of the short-range repulsive force, the existence of a structured layer of water molecules at the silica surface is the most accepted explanation for it. The overlap of structured water layers of different surfaces leads to repulsive forces, which are known as hydration forces. This assumption is based on the very hydrophilic nature of silica. Different theories have been developed in order to reproduce the exponentially decaying behavior (as a function of the separation distance) of the hydration forces. Different mechanisms for the formation of the structured water layer around the silica surfaces are considered by each theory. By the aid of an AFM and the colloid probe technique, the interaction forces between silica surfaces have been measured directly at different pH values and salt concentrations. The results confirm the presence of the short-range repulsion at any experimental condition (even at high salt concentration). A comparison between the experimental data and theoretical fits obtained from different theories has been performed in order to elucidate the nature of this non-DLVO repulsive force.  相似文献   

13.
Polyelectrolyte multilayer films containing nanocrystalline cellulose (NCC) and poly(allylamine hydrochloride) (PAH) make up a new class of nanostructured composite with applications ranging from coatings to biomedical devices. Moreover, these materials are amenable to surface force studies using colloid-probe atomic force microscopy (CP-AFM). For electrostatically assembled films with either NCC or PAH as the outermost layer, surface morphology was investigated by AFM and wettability was examined by contact angle measurements. By varying the surrounding ionic strength and pH, the relative contributions from electrostatic, van der Waals, steric, and polymer bridging interactions were evaluated. The ionic cross-linking in these films rendered them stable under all solution conditions studied although swelling at low pH and high ionic strength was inferred. The underlying polymer layer in the multilayered film was found to dictate the dominant surface forces when polymer migration and chain extension were facilitated. The precontact normal forces between a silica probe and an NCC-capped multilayer film were monotonically repulsive at pH values where the material surfaces were similarly and fully charged. In contrast, at pH 3.5, the anionic surfaces were weakly charged but the underlying layer of cationic PAH was fully charged and attractive forces dominated due to polymer bridging from extended PAH chains. The interaction with an anionic carboxylic acid probe showed similar behavior to the silica probe; however, for a cationic amine probe with an anionic NCC-capped film, electrostatic double-layer attraction at low pH, and electrostatic double-layer repulsion at high pH, were observed. Finally, the effect of the capping layer was studied with an anionic probe, which indicated that NCC-capped films exhibited purely repulsive forces which were larger in magnitude than the combination of electrostatic double-layer attraction and steric repulsion, measured for PAH-capped films. Wherever possible, DLVO theory was used to fit the measured surface forces and apparent surface potentials and surface charge densities were calculated.  相似文献   

14.
Polyelectrolyte brushes were built on mica by anchoring polystyrene-poly(acrylic acid) (PS-b-PAA) diblock copolymers at a controlled surface density in a polystyrene monolayer covalently attached to OH-activated mica surfaces. Compared to physisorbed polymer brushes, these irreversibly attached charged brushes allow the polymer grafting density to remain constant upon changes in environmental conditions (e.g., pH, salt concentration, compression, and shear). The normal interaction and friction forces as a function of surface separation distance and at different concentrations of added salt (NaCl) were investigated using a surface forces apparatus. The interaction force profiles were completely reversible both on loading and receding and were purely repulsive. For a constant polymer grafting density, the influence of the polyelectrolyte charges and the Debye screening effect on the overall interaction forces was investigated. The experimental interaction force profiles agree very well with scaling models developed for neutral and charged polymer brushes. The variation of the friction force between two PAA brushes in motion with respect to each other as a function of surface separation distance appeared to be similar to that observed with neutral brushes. This similarity suggests that the increase in friction is associated with an increase in mutual interpenetration upon compression as observed with neutral polymers. The effect of the PAA charges and added ions was more significant on the repulsive normal forces than on the friction forces. The reversible characteristics of the normal force profiles and friction measurements confirmed the strong attachment of the PAA brushes to the mica substrate. High friction coefficients (ca 0.3) were measured at relatively high pressures (40 atm) with no surface damage or polymer removal.  相似文献   

15.
Nanoscale repulsive forces between mineral surfaces in aqueous solutions were measured for the asymmetric mica-silica system. The force measured with an atomic force microscope (AFM) has universal character in the short range, less than ~1 nm or about 3-4 water molecules, independent of solution conditions, that is, electrolyte ion (Na, Ca, Al), concentration (10(-6)-10(-2)M), and pH (3.9-8.2). Notably, the force is essentially the same as for the glass-silica system. Single force curves for a mica-silica system in a 10(-4)M aqueous NaCl solution at pH ~ 5.1 show oscillations with a period of about 0.25 nm, roughly the diameter of a water molecule, a consequence of a layer-by-layer dehydration of the surfaces when pushed together. This result provides additional support to the idea that nanoscale repulsive forces between mineral surfaces in aqueous solutions arise from a surface-induced water effect; the water between two mineral plates that are pushed together becomes structured and increasingly anchored to the surface of the plates by the creation of a hydrogen-bonding network that prevents dehydration of the surfaces.  相似文献   

16.
A novel thermo- and pH-sensitive nanogel particle, which is a core-shell structured particle with a poly(N-isopropylacrylamide) (p(NIPAAm)) hydrogel core and a poly(ethylene glycol) monomethacrylate grafted poly(methacrylic acid) (p(MMA-g-EG)) shell, is of interest as a vehicle for the controlled release of peptide drugs. The interactions between such nanogel particles and artificial mucin layers during both approach and separation were successfully measured by using colloid probe atomic force microscopy (AFM) under various compression forces, scan velocities, and pH values. While the magnitudes of the compression forces and scan velocities did not affect the interactions during the approach process, the adhesive force during the separation process increased with these parameters. The pH values significantly influenced the interactions between the nanogel particles and a mucin layer. A large steric repulsive force and a long-range adhesive force were measured at neutral pH due to the swollen p(MMA-g-EG) shell. On the other hand, at low pH values, the steric repulsive force disappeared and a short-range adhesive force was detected, which resulted from the collapse of the shell layer. The nanogel particles possessed a pH response that was sufficient to protect the incorporated peptide drug under the harsh acidic conditions in the stomach and to effectively adhere to the mucin layer of the small intestine, where the pH is neutral. The relationships among the nanogel particle-mucin layer interactions, pH conditions, scan velocities, and compression forces were systemically investigated and discussed.  相似文献   

17.
We propose a force measurement method for evaluating the binding force between microscale flat surfaces in an aqueous solution. Using force-sensing piezoresistive cantilevers with sub-nanonewton force resolution, we have directly measured binding forces between SiO2-SiO2 microcontacts, which were created by gravity-driven random collision between microfabricated SiO2 cylindrical particles and a planar SiO2 substrate in a HCl solution. First, to examine our method we measured the pH dependence of the binding force. The binding forces were 12 and 5.8 nN at pH 1.0 and 2.0, respectively. As the pH increased, the binding force decreased and became zero at pH greater than 3.0. We confirmed that the bindings were based on the van der Waals' (VDW) force at pH 2.0 or less whereas a repulsive double-layer force acted between the surfaces at pH 3.0 or more. Second, the binding forces were categorized into a friction force or an adhesion force between the particles and the substrate. In the measurement, the friction force between the particle and the substrate was measured in the case when the particle slid on the substrate. On the contrary, the adhesion force was measured when the particle came off the substrate. Whether the particle slid or came off depended on the aspect ratio of the particle. We fabricated cylindrical particles with an aspect ratio of 0.03-2.0 and distinguished the friction force from the adhesion force by changing the aspect ratio of the particles. As a result, the friction force per unit contact area between SiO2-SiO2 flat surfaces was found to be 330 pN/microm2 +/- 20% when we used particles with a low aspect ratio (<0.1), and the adhesion force per unit contact area was 90 pN/microm2 +/- 20% for particles with a high aspect ratio (>0.4). For fluidic self-assembly that utilizes microscale surface contact in a liquid, our measurement method is an effective tool for studying and developing systems.  相似文献   

18.
A systematic study of the surface forces between a cellulose sphere and cellulose thin films of varying crystallinity has been conducted as a function of ionic strength and pH. Semicrystalline cellulose II surfaces and amorphous cellulose films were prepared by spin-coating of the precursor cellulose solutions onto oxidized silicon wafers before regeneration in water. Crystalline cellulose I surfaces were prepared by spin-coating wafers with aqueous suspensions of sulfate-stabilized cellulose I nanocrystals. These preparation methods produced thin, smooth films suitable for surface forces measurements. The interaction with the cellulose I was monotonically repulsive at pH 3.5, 5.8, and 8.5 and at 0.1, 1, and 10 mM ionic strengths. This was attributed to the presence of strongly ionizable sulfur-containing groups on the cellulose nanocrystal surfaces. The amorphous film typically showed a steric interaction up to 100 nm away from the interface that was independent of the solution conditions. A range of surface forces were successfully measured on the semicrystalline cellulose II films; attractive and repulsive regimes were observed, depending on pH and ionic strength, and were interpreted in terms of van der Waals and electrostatic interactions. Clearly, the forces acting near cellulose surfaces are very dependent on the way the cellulose surface has been prepared.  相似文献   

19.
We have used a surface forces apparatus to measure the normal force between two solid curved surfaces confining a film of nematic liquid crystal (5CB, 4'-n-pentyl-4-cyanobiphenyl) under hybrid planar-homeotropic anchoring conditions. Upon reduction of the surface separation D, we measured an increasingly repulsive force in the range D = 35-80 nm, reaching a plateau in the range D = 10-35 nm, followed by a short-range oscillatory force at D < 5 nm. The oscillation period was comparable to the cross-sectional diameter of the liquid crystal molecule and characteristic of a configuration with the molecules parallel to the surfaces. These results show that the director field underwent a confinement-induced transition from a splay-bend distorted configuration at large D, which produces elastic repulsive forces, to a uniform planar nondegenerate configuration with broken homeotropic anchoring, which does not produce additional elastic forces as D is decreased. These findings, supported by measurements of the birefringence of the confined film at different film thicknesses, provide the first direct observation of an anchoring transition on the nanometer scale.  相似文献   

20.
We present a newly designed electrochemical surface forces apparatus (EC-SFA) that allows control and measurement of surface potentials and interfacial electrochemical reactions with simultaneous measurement of normal interaction forces (with nN resolution), friction forces (with μN resolution), and distances (with ? resolution) between apposing surfaces. We describe three applications of the developed EC-SFA and discuss the wide-range of potential other applications. In particular, we describe measurements of (1) force-distance profiles between smooth and rough gold surfaces and apposing self-assembled monolayer-covered smooth mica surfaces; (2) the effective changing thickness of anodically growing oxide layers with ?-accuracy on rough and smooth surfaces; and (3) friction forces evolving at a metal-ceramic contact, all as a function of the applied electrochemical potential. Interaction forces between atomically smooth surfaces are well-described using DLVO theory and the Hogg-Healy-Fuerstenau approximation for electric double layer interactions between dissimilar surfaces, which unintuitively predicts the possibility of attractive double layer forces between dissimilar surfaces whose surface potentials have similar sign, and repulsive forces between surfaces whose surface potentials have opposite sign. Surface roughness of the gold electrodes leads to an additional exponentially repulsive force in the force-distance profiles that is qualitatively well described by an extended DLVO model that includes repulsive hydration and steric forces. Comparing the measured thickness of the anodic gold oxide layer and the charge consumed for generating this layer allowed the identification of its chemical structure as a hydrated Au(OH)(3) phase formed at the gold surface at high positive potentials. The EC-SFA allows, for the first time, one to look at complex long-term transient effects of dynamic processes (e.g., relaxation times), which are also reflected in friction forces while tuning electrochemical surface potentials.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号