高纯La-Ni-Al合金成分及杂质元素的分析方法研究

叙述了镧－镍－铝（La-Ni-Al)合金分镍、铝及微量杂质元素锌、铁、锰、镁、硅、铜和钙的ICP－AES测定方法。样品以HNO3（1＋1）溶解,稀释后直接测定主量元素镍和铝;用基体匹配法补偿基体效应测定其他杂质元素。各元素回收率在95％－106％,相对标准偏差优于5％。     

ICP—AES法测定锌及其化合物中的杂质元素

采用样品溶解后直接测定及氢氧化钇共沉淀将锌与被测杂质元素分离后测定相结合，研究了锌及其化合物中Ａｇ，Ｃｏ，Ａｌ，Ｎｉ，Ｆｅ，Ｃｕ，Ｃｄ，Ｃｒ，Ｍｎ，Ｉｎ，Ａｓ，Ｐｂ，Ｓｎ，Ｓｂ，Ｂｉ等１５个杂质元素的ＩＣＰ－ＡＥＳ测定方法，相对标准偏差１．６－８．１％。     

ICP—AES法测定高纯二氧化锆中痕量杂质

介绍了高纯二氧化锆中痕量杂质元素Ｆｅ，Ｎａ，Ｓｉ，Ｔｉ的ＩＣＰ－ＡＥＳ测定方法。样品以浓Ｈ２ＳＯ４及（ＮＨ４）２ＳＯ４溶解，采用空白背景校正法消除基体Ｚｒ的光谱干扰，以基体匹配法补偿基体效应。各元素平均回收率为９５％－１０６％，相对标准偏差为１．３％－３．０％。     

基体分离ICP-AES法测定金属锇粉中的杂质元素

本文介绍了用浓硝酸在２００℃下溶解样品,同时把锇氧化成易挥发的氧化物离去并用氢氧化钠吸收,残液用ＩＣＰ－ＡＥＳ测定的方法。方法检测限为０．００５－０．１３４μｇ．ｍＬ＾－１,回收率为９１％－１１２％,精密度小于３％,同时测定１８种杂质元素,具有简单快速和准确度高的优越性。     

ICP-AES法直接测定重晶石中的Ca、Sr、Fe

通过碳酸钠高温熔样，热水浸取过渡除去SO4^2-和Na^2 ，酸化溶解沉淀的方法处理样品，采用ICP－AES法测定重晶石中的杂质元素钙、锶、铁，方法的检出限为3．9－8．4ng／mL，回收率为99．4％－100．3％，精密度为1．1％－1．4％。该方法快速、简便，在重晶石日常检测中具有重要的实际意义。     

原子吸收法同时测定大豆及其乳制品中Zn、Cu、Co、Fe、Mn

本文采用干法灰化和湿法消化溶解样品，原子吸收法测定大豆及其乳制品中Zn、Cu、Co、Fe、Mn等元素。方法快速、简便，回收率为96％－103％。     

ICP-AES测定铜合金中的铜及10种杂质元素

建立了ICP-AES同时测定铜合金中铜及杂质元素磷、硅、锰、铁、镍、钴、锌、铅、铝、锡11种元素的分析方法,通过对样品溶解方法、元素分析谱线的选择和仪器分析参数进行试验比较,确定了实验条件,并对铜合金标准样品进行了精密度和回收率实验.结果表明,相对标准偏差小于3.0％,回收率在90％-110％之间.该方法快速简便,准确度高,可以满足日常检验的分析要求.     

ICP-AES测定铝锭中八种杂质元素

本文研究了名对铁、锰、铜、锌、镁、钛、硅、镓等分析元素的干扰情况,采用了基体匹配法进行基体干扰校正,采用干扰系数法扣除杂质元素间光谱干扰引起的分析偏差,从而确定了铝锭中八种杂质元素同时测定的最佳工作条件,并用实际样品把本方法与化学法的测定进行对比,结果令人满意。方法回收率在９２．９％－１０５％之间,精密度在０．８２％－２．３２％之间,该方法快速、简便、可靠,适用于进出口铝锭的日常检验。     

ICP－AES法测定钒酸钇晶体中的掺杂稀土元素铒和铕的含量

本文用硫酸溶解样品，以ＩＣＰ－ＡＥＳ法对钒酸钇晶体中掺杂稀土元素铒和铕进行测定，取得满意结果，回收率分别是９８％－１０４％和９６％－１０５％；相对标准偏差３％以内。文中选择了相宜的内标元素并研究了硫酸浓度和基体浓度对被测元素的谱线强度的影响。     

ICP-AES法同时测定氯化锂和氢氧化锂中七种杂质元素

本文报导了用ＩＣＰ－ＡＥＳ法同时测定ＬｉＣｌ和ＬｉＯＨ·Ｈ２Ｏ中７种杂质元素Ａｌ、Ｂａ、Ｃａ、Ｆｅ、Ｍｇ、Ｓｉ、Ｚｎ的分析方法。研究了基体元素锂对被测元素的基体效应，采用基体匹配法与背景扣除法进行校正。被测元素的检出限为０．１－９．４ｎｇ／ｍＬ，加标试验回收率为９２％－１０９％，当杂质元素含量为０．０００１％－０．０２８％时，相对标准偏差小于７％。方法简便、快速、准确，用于样品分析，取得了满意的结果。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.