Charge storage and screening of the internal field in GaN/AlGaN quantum wells

The optical spectra of a set of high quality quantum wells, with well characterized structural parameters, are presented here. We propose a quantitative calculation for the measured emission energies which takes into account the spontaneous and piezoelectric polarization fields and the field-screening effect due to electron-hole photogenerated pairs; such an effect is especially effective in wide QW samples which in fact behave like mesoscopic capacitors.     

Influence of AlGaN/GaN/InGaN superlattice on the characteristics of LEDs grown by metalorganic chemical vapor deposition

This study examined the influence of strain-compensated triple AlGaN/GaN/InGaN superlattice structures (SLs) in n-GaN on the structural, electrical and optical characteristics of LEDs by analyzing the etch pits density (EPD), stress measurement, high-resolution X-ray diffraction (HRXRD), sheet resistance, photoluminescence (PL) and light–current–voltage (L–I–V). EPD, stress measurement and HRXRD studies showed that the insertion of AlGaN/GaN/InGaN SLs during the growth of n-GaN effectively distributed and compensated for the strong compressive stress, and decreased the dislocation density in n-GaN. The operating voltage at 20 mA for the LEDs grown with SLs decreased to 3.18 V from 3.4 V for the LEDs grown without SLs. In addition, a decrease in the spectral blue shift compared to the LEDs grown without SLs was observed in the LEDs grown with the SLs.     

Characterization of polycrystalline GaN grown on silica glass substrates

The structural, optical, and electrical properties of GaN films grown on silica glass substrate by metalorganic chemical vapor deposition were studied. X-ray diffraction showed that the films were grown in hexagonal structure with a predominant (0 0 0 2) peak. A broad and strong band-edge emission and very weak yellow luminescence in photoluminescence (PL) spectra were observed. And the temperature dependence of the PL spectra was extensively studied. The thermal quenching activation energy was found to be very close to the donor activation energy determined from the temperature dependence of the carrier concentration. Longitudinal optical phonons were found to be responsible for the PL broadening above 100 K.     

GaP:Mg layers grown on GaN by MOCVD

We have investigated the growth of magnesium-doped GaP (GaP:Mg) layers on GaN by metalorganic chemical vapor deposition. The hole carrier concentration increased linearly from 0.8×10¹⁸ to 4.2×10¹⁸ cm⁻³ as the Bis(cyclopentadienyl) magnesium (Cp₂Mg) mole flow rate increased from 1.2×10⁻⁷ to 3.6×10⁻⁷ mol/min. However, the hole carrier concentration decreased when the CP₂Mg mole flow rate was further increased. The double crystal X-ray diffraction (DCXRD) rocking curves showed that the GaP:Mg layers were single crystalline at low CP₂Mg molar flow. However, the GaP:Mg layers became polycrystalline if the CP₂Mg molar flow was too high. The decrease in hole carrier concentration at high CP₂Mg molar flow was due to crystal quality deterioration of the GaP layer, which also resulted in the low hole mobility of the GaP:Mg layer.     

Polarization induced 2D hole gas in GaN/AlGaN heterostructures

The generation of high density 2D hole gases is crucial for further progress in the electronic and optoelectronic nitride devices. In this paper, we present systematic theoretical studies of Mg-doped GaN/AlGaN gated heterostructures and superlattices. Our calculations are based on a self-consistent solution of the multiband k.p Schrödinger and Poisson equation and reveal that the hole 2D sheet density is mainly determined by the polarization induced interface charges. For an aluminium concentration of 30%, the induced hole density in the heterostructure can reach values up to 1.5×10¹³ cm⁻². In the GaN/AlGaN superlattices, the hole sheet density increases with the superlattice period and saturates for a period of 40 nm at a value of 1.5×10¹³ cm⁻².     

High-resolution X-ray diffraction analysis of the Bragg peak integrated intensity in highly mismatched III-N epilayers

A new method of measuring the thickness of GaN epilayers on sapphire (0 0 0 1) substrates by using double crystal X-ray diffraction was proposed. The ratio of the integrated intensity between the GaN epilayer and the sapphire substrate showed a linear relationship with the GaN epilayer thickness up to 2.12 μm. It is practical and convenient to measure the GaN epilayer thickness using this ratio, and can mostly eliminate the effect of the reabsorption, the extinction and other scattering factors of the GaN epilayers.     

Thermal stability of thin InGaN films on GaN

The thermal stability of ∼200-nm-thick InGaN thin films on GaN was investigated using isothermal and isochronal post-growth anneals. The In_xGa_1−xN films (x=0.08–0.18) were annealed in N₂ at 600–1000 °C for 15–60 min, and the resulting film degradation was monitored using X-ray diffraction (XRD) and photoluminescence (PL) measurements. As expected, films with higher indium concentration showed more evidence for decomposition than the samples with lower indium concentration. Also for each alloy composition, decreases in the PL intensity were observed starting at much lower temperatures compared to decreases in the XRD intensity. This difference in sensitivity of the PL and XRD techniques to the InGaN decomposition suggest that defects that quench luminescence are generated prior to the onset of structural decomposition. For the higher indium concentration films, the bulk decomposition proceeds by forming metallic indium and gallium regions as observed by XRD. For the 18% indium concentration film, measurement of the temperature-dependent InGaN decomposition yields an activation energy, E_A, of 0.87±0.07 eV, which is similar to the E_A for bulk InN decomposition. The InGaN integrated XRD signal of the 18% film displays an exponential decrease vs. time, implying InGaN decomposition proceeds via a first-order reaction mechanism.     

The influence of the Al pre-deposition on the properties of AlN buffer layer and GaN layer grown on Si (1 1 1) substrate

The influence of Al pre-deposition on the properties of AlN buffer layer and GaN layer grown on Si (1 1 1) substrate by metalorganic chemical vapor deposition (MOCVD) has been systematically studied. Compared with the sample without Al pre-deposition, optimum Al pre-deposition time could improve the AlN buffer layer crystal quality and reduce the root mean square (RMS) roughness. Whereas, overlong Al-deposition time deteriorated the AlN crystal quality and Al-deposition patterns could be found. Cracks and melt-back etching patterns appeared in the GaN layer grown without Al pre-deposition. With suitable Al-deposition time, crack-free 2.0 μm GaN was obtained and the full-width at half-maximum (FWHM) of (0 0 2) plane measured by double crystal X-ray diffraction (DCXRD) was as low as 482 arcsec. However, overlong Al-deposition time would result in a great deal of cracks, and the crystal quality of GaN layer deteriorated. The surface of GaN layer became rough in the region where the Al-deposition patterns were formed due to overlong Al-deposition time.     

Experimental and theoretical investigations of the electrical properties of undoped and magnesium-doped GaN layers

The ac characteristics of GaN : Mg and undoped GaN layers, grown by MOVPE on sapphire substrates, are measured for a wide range of temperature and bias conditions, in order to investigate the effect of the magnesium-related level on the transport properties. Two peaks, whose height and position depend on the measurement temperature, are observed in the admittance curves (G/ω versus frequency) of the Mg-doped samples, whereas only one peak appears in undoped samples. The study of the frequency dependence of the impedance, with a model including the two metallic Au/GaN junctions, the GaN layer itself, shows that, besides the effect of the differential resistance of the layer which plays a role in both sample types, the presence of a Mg-related deep level contributes to the observed variations of the peaks in the admittance curves of the p-doped samples. Results of a theoretical steady-state and small-signal analysis based on numerical modelling of the Au/GaN/Au heterostructure complete our analysis.     

Method for HVPE growth of thick crack-free GaN layers

Twenty-five micrometer thick GaN was grown with hydride vapor phase epitaxy (HVPE) on metal-organic chemical vapor deposition (MOCVD) grown templates on sapphire substrates with the gallium treatment step (GTS) technique with varying buffer layer thickness. The samples are studied with atomic force microscopy (AFM), etching and scanning electron microscopy (SEM), photo-luminescence (PL), X-ray diffraction (XRD) and optical microscopy. The results show that the thickness of the buffer layer is not important for the layer quality once the growth in MOCVD starts to make the transition from 3D growth to 2D growth and HVPE continues in the same growth mode. We show that the MOCVD templates with GTS technique make excellent templates for HVPE growth, allowing growth of GaN without cracks in either sapphire or GaN.     

Enhanced growth rates and reduced parasitic deposition by the substitution of Cl2 for HCl in GaN HVPE

The main limitation in the application of hydride vapor phase epitaxy for the large scale production of thick free-standing GaN substrates is the so-called parasitic deposition, which limits the growth time and wafer thickness by blocking the gallium precursor inlet. By utilizing Cl₂ instead of the usual HCl gas for the production of the gallium chlorine precursor, we found a rapid increase in growth rate from ∼80 to ∼400 μm/h for an equally large flow of 25 sccm. This allowed us to grow, without any additional optimization, 1.2 mm thick high quality GaN wafers, which spontaneously lifted off from their 0.3° mis-oriented GaN on sapphire HCl-based HVPE templates. These layers exhibited clear transparencies, indicating a high purity, dislocation densities in the order of 10⁶ cm⁻², and narrow rocking curve XRD FWHMs of 54 and 166 arcsec in for the 0002 and 101−5 directions, respectively.     

Electrical characterisation of AlGaN/GaN heterostructure wafers for high-power HFETs

Undoped 28 nm AlGaN on 1 μm GaN was grown by MOVPE for high power microwave HFETs. Non-destructive methods for rapid characterisation of the layers are described. Double contact mercury probe capacitance voltage measurements gave valuable information on AlGaN layer leakage, thickness and quality, but only gave an estimate of the carrier concentration and pinch-off voltage due to the absence of an ohmic contact to the 2DEG layer. A non-contact resistivity mapping system gave accurate average sheet resistance, but underestimated the cross-wafer variation.     

Study on optimal growth conditions of a-plane GaN grown on r-plane sapphire by metal-organic chemical vapor deposition

Non-polar a-plane GaN thin films were grown on r-plane sapphire substrates by metal-organic chemical vapor deposition. In order to obtain a-plane GaN films with better crystal quality and surface morphology, detailed comparisons between different growth conditions were investigated. The results showed that high-temperature and low-pressure conditions facilitating two-dimensional growth could lead to a fully coalesced a-plane GaN layer with a very smooth surface. The best mean roughness of the surface morphology was 10.5 Å. Various thickness values of AlN nucleation layers and the V/III ratios for growth of the a-plane GaN bulk were also studied to determine the best condition for obtaining a smooth surface morphology of the a-plane GaN layer.     

Growth of high quality a-plane GaN epi-layer on r-plane sapphire substrates with optimization of multi-buffer layer

Nonpolar (1 1–2 0) a-plane GaN films have been grown using the multi-buffer layer technique on (1–1 0 2) r-plane sapphire substrates. In order to obtain epitaxial a-plane GaN films, optimized growth condition of the multi-buffer layer was investigated using atomic force microscopy, high resolution X-ray diffraction, and transmission electron microscopy measurements. The experimental results showed that the growth conditions of nucleation layer and three-dimensional growth layer significantly affect the crystal quality of subsequently grown a-plane GaN films. At the optimized growth conditions, omega full-width at half maximum values of (11–20) X-ray rocking curve along c- and m-axes were 430 and 530 arcsec, respectively. From the results of transmission electron microscopy, it was suggested that the high crystal quality of the a-plane GaN film can be obtained from dislocation bending and annihilation by controlling of the island growth mode.     

Differences in nucleation and properties of InN islands formed using two different deposition procedures

The initial stages of metalorganic chemical vapor deposition of InN have been investigated using two different growth procedures: growth of InN over a GaN buffer layer in one continuous run and growth of InN on a pre-deposited GaN template. While the growth conditions and material quality of the GaN underlying layers are nominally the same, characterization by AFM, X-ray diffraction and PL spectroscopy reveals significantly different material properties of InN islands formed using the two procedures and suggests a different path of evolution during the initial stages of growth. In particular, InN islands grown on a pre-deposited GaN template seem to nucleate directly on the GaN template and are 5 times larger in volume and 2 times lower in surface density as compared with InN growth in one continuous run with the GaN underlying layer. Our studies suggest that the Ga incorporation into the InN during the growth on a GaN buffer layer in one continuous run plays a significant role in altering InN growth mechanisms and material properties.     

In situ optical monitoring of AlGaN thickness and composition during MOVPE growth of AlGaN/GaN microwave HFETs

Real-time spectral reflectometry has been implemented to monitor the MOVPE growth of AlGaN/GaN microwave HFET structures. The aim is to monitor and control the thickness and composition of the thin AlGaN layer during growth. In order to extract useful information from the in situ spectra the optical constants of AlGaN as a function of alloy composition are required at the growth temperature (1050°C). As the first step to obtaining the high temperature optical constants, a room temperature spectroscopic ellipsometry study (energy range 1.65–4.95 eV) has been carried out on thin AlGaN films of various thickness (30 and 100 nm) and aluminium content (0.15 and 0.25). The multilayer model of each sample from the ellipsometry study is used to generate a reflectance spectrum which is compared with the in situ spectral reflectometry spectrum of the same sample acquired at room temperature to verify the technique. Further work is in progress to model the bandgap and optical constants of GaN and AlGaN at growth temperature.     

Growth of height-controlled InGaN quantum dots on GaN

InGaN height-controlled quantum dots (HCQDs) were grown by alternately depositing In_0.4Ga_0.6N QD and In_0.1Ga_0.9N spacer layers on a seed In_0.4Ga_0.6N QD layer. Structural and optical studies showed that the height of the InGaN QDs was controlled by the deposition cycle of In_0.4Ga_0.6N/In_0.1Ga_0.9N layers. Photoluminescence studies showed that the In_0.4Ga_0.6N HCQDs provided deep potential wells and the piezoelectric field-induced quantum-confined Stark effect was negligibly small. These phenomena are attributed to variation in quantum confinement energy in the electronically coupled InGaN HCQDs providing deep potential wells.     

Ab initio study of the effect of doping on stacking faults in GaN

The influence of impurities on the basal plane stacking fault energy in GaN is investigated using density functional theory. It is found that silicon, indium, magnesium and carbon impurities each reduce the stacking fault energy by introducing changes to the bonding properties of the material. These bonding properties are analysed in terms of Mulliken charges and bond populations. It is found that the reduction in stacking fault energy correlates both with a reduction in the average anion charge and with an increase in the overlap population.     

MOCVD growth of GaN on Si(1 1 1) substrates using an ALD-grown Al2O3 interlayer

GaN thin films have been grown on Si(1 1 1) substrates using an atomic layer deposition (ALD)-grown Al₂O₃ interlayer. This thin Al₂O₃ layer reduces strain in the subsequent GaN layer, leading to lower defect densities and improved material quality compared to GaN thin films grown by the same process on bare Si. XRD ω-scans showed a full width at half maximum (FWHM) of 549 arcsec for GaN grown on bare Si and a FWHM as low as 378 arcsec for GaN grown on Si using the ALD-grown Al₂O₃ interlayer. Raman spectroscopy was used to study the strain in these films in more detail, with the shift of the E₂(high) mode showing a clear dependence of strain on Al₂O₃ interlayer thickness. This dependence of strain on Al₂O₃ thickness was also observed via the redshift of the near bandedge emission in room temperature photoluminescence (RT-PL) spectroscopy. The reduction in strain results in a significant reduction in both crack density and screw dislocation density compared to similar films grown on bare Si. Screw dislocation density of the films grown on Al₂O₃/Si substrates approaches that of typical GaN layers on sapphire. This work shows great promise for the use of oxide interlayers for growth of GaN-based LEDs on Si.     

High-quality a-plane GaN grown with flow-rate modulation epitaxy on r-plane sapphire substrate

We use the flow-rate modulation epitaxy (FME) technique to improve the crystal quality of a pit-free a-plane GaN (1 1 2¯ 0) film grown on r-plane sapphire (1 1¯ 0 2) substrate. With the FME technique, the width of the rocking curve in X-ray diffraction measurement is significantly reduced. Also, the surface roughness in either atomic-force-microscopy scanning or -step profiling is decreased. Here, the FME technique means to alternatively turn on and off the supply of Ga atoms, while N atoms are continuously supplied without changing the flow rate. Under the used growth conditions, the optimized FME parameters include the on/off periods at 10/10 s. During the period of closing the flow of trimethylgallium (TMGa), the continuous supply of nitrogen can lead to the formation of stoichiometry structure under the high-Ga growth condition, which is required for pit-free growth. Also, during this period, Ga atoms can further migrate to result in a flatter surface. Therefore, the crystal quality of the a-plane GaN sample can be improved.