Optimising uniformity of InAs/(InGaAs)/GaAs quantum dots grown by metal organic vapor phase epitaxy

A route towards optimisation of uniformity and density of InAs/(InGaAs)/GaAs quantum dots grown by metal organic vapor phase epitaxy (MOVPE) through successive variations of the growth parameters is reported. It is demonstrated that a key parameter in obtaining a high density of quantum dots is the V/III ratio, a fact which was shown to be valid when either AsH₃ (arsine) or tertiary-butyl-arsine (TBA) were used as group V precursors. Once the optimum V/III ratio was found, the size distribution was further improved by adjusting the nominal thickness of deposited InAs material, resulting in an optimum thickness of 1.8 monolayers of InAs in our case. The number of coalesced dots was minimised by adjusting the growth interruption time to approximately 30 s. Further, the uniformity was improved by increasing the growth temperature from 485 °C to 520 °C. By combining these optimised parameters, i.e. a growth temperature of 520 °C, 1.8 monolayers InAs thickness, 30 s growth stop time and TBA as group V precursor, a full-width-half-maximum (FWHM) of the low temperature luminescence band of 40 meV was achieved, indicating a narrow dot size distribution.     

Sb-mediated growth of high-density InAs quantum dots and GaAsSb embedding growth by MBE

Self-assembled InAs quantum dots (QDs) with high-density were grown on GaAs(0 0 1) substrates by antimony (Sb)-mediated molecular beam epitaxy technique using GaAsSb/GaAs buffer layer and InAsSb wetting layer (WL). In this Sb-mediated growth, many two-dimensional (2D) small islands were formed on those WL surfaces. These 2D islands provide high step density and suppress surface migration. As the results, high-density InAs QDs were achieved, and photoluminescence (PL) intensity increased. Furthermore, by introducing GaAsSb capping layer (CL), higher PL intensity at room temperature was obtained as compared with that InGaAs CL.     

Optimization of Metamorphic InGaAs Quantum Wells on GaAs Grown by Molecular Beam Epitaxy

We investigate the molecular beam epitaxy growth of metamorphic InxGal-xAs materials （x up to 0.5） on GaAs substrates systematically. Optimization of structure design and growth parameters is aimed at obtaining smooth surface and high optical qualdty. The optimized structures have an average surface roughness of 0.9-1.8 nm. It is also proven by PL measurements that the optical properties of high indium content （55%） InGaAs quantum wells are improved apparently by defect reduction technique and by introducing Sb as a surfactant. These provide us new ways for growing device quality metamorphic structures on GaAs substrates with long-wavelength emissions.     

Low Density Self-Assembled InAs/GaAs Quantum Dots Grown by Metal Organic Chemical Vapour Deposition

The self-assembled InAs quantum dots （QDs） on GaAs substrates with low density （5×10^8 cm^-2） are achieved using relatively higher growth temperature and low InAs coverage by low-pressure metal-organic chemical vapour deposition. The macro-PL spectra exhibit three emission peaks at 1361, 1280 and 1204nm, corresponding to the ground level （GS）, the first excited state （ES1） and the second excited state （ES2） of the QDs, respectively, which are obtained when the GaAs capping layer is grown using triethylgallium and tertiallybutylarsine. As a result of micro-PL, only a few peaks from individual dots have been observed. The exciton-biexciton behaviour was clearly observed at low temperature.     

Effect of GaAs/GaSb Combination Strain-Reducing Layer on Self-Assembled InAs Quantum Dots

Self-assembled quantum dots capping with a GaAs/Gasb combined strain-reduced layer （CSRL） are grown by MBE. Their structural and optical properties are investigated by AFM and photoluminescence （PL）. PL measurements have shown that stronger emission about 1.3μm can be obtained by Sb irradiation and capping QDs with 3 ML GaAs/2 ML GaSh CSRL at room temperature. The full width at half maximum （FWHM） of the PL spectrum is about 20.2 meV （19.9 meV） at room temperature （2OK）, indicating that the QDs have high uniform, The result of FWHM is much better than the recently reported result, which is due to the fact that lower QD growth rate and growth interruption after the QDs deposition are adopted in our experiments.     

Reaction kinetic model of height selection in heteroepitaxial growth of quantum dots

A reaction kinetic model is proposed for height selection of heteroepitaxially growing nanometer-thick quantum dots. The model describes the growth by a set of rate equations for the combined size and height distributions of the dots. In addition to nucleation and growth, the model includes a coarse-grained conversion rate incorporating kinetics of height changes. With suitably chosen rate coefficients the model reproduces qualitatively the experimentally observed height-selected size distributions and their evolution. The results support the view that the height selection and the form of the size distribution both result from the oscillating energy barrier for the transformation of dots of different heights, and this transformation barrier is considerably larger in magnitude than oscillations in the electronic energy due to quantum well states in the dot.     

Abnormal temperature dependence of photoluminescence from self-assembled InAs quantum dots covered by an InAlAs/InGaAs combination layer

In this report we have investigated the temperature dependence of photoluminescence (PL) from self-assembled InAs quantum dots (QDs) covered by an InAlAs/InGaAs combination layer. The ground state experiences an abnormal variation of PL linewidth from 15 K up to room temperature. Meanwhile, the PL integrated intensity ratio of the first excited state to the ground state for InAs QDs unexpectedly decreases with increasing temperature, which we attribute to the phonon bottleneck effect. We believe that these experimental results are closely related to the partially coupled quantum dots system and the large energy separation between the ground and the first excited states.     

Size selected growth of nanodots: effects of growth kinetics and energetics on the formation of stationary size distributions

The size selection of nanodots during the growth is studied by using a reaction kinetic model, where reaction rates depend on the dot size. The characteristic feature of the reaction rates is the energetics, where the free energy of dots has a minimum at the certain dot size. The model equations are solved by using a particle coalescence simulation method. We find phenomenologically three distinct stages of growth. First, during the initial deposition stage, distributions with high density of small dots occur. Second, there is an intermediate and short-lived stationary state, which is controlled by kinetics of growth. Third, a long-lived stationary state is obtained, with nearly Gaussian size distributions, mostly determined by the energetics of the growth but also significantly affected by the kinetics. In the final stage, size selection and narrowing of the distributions occur. It is also shown that in the final stage of growth the Fokker-Planck type continuum model describes well the evolution of the distributions and the size selection.     

Energy levels of a spherical quantum dot in a confining potential

Using an exact analytical method, we obtain the ground state and the excited states wave functions as well as the corresponding eigenvalues of a spherical quantum dot in the presence of a confining potential which is a combination of linear, Coulomb and quadratic terms. Next, we investigate the quantum dot energy as the potential coefficients are changed. Our study reveals that considering such a confining potential leads to results which are in good agreement with experimental results.     

Excitonic absorption of spherical PbS nanoparticles in zeolite A

We report the optical and structural properties of PbS nanoparticles in zeolite A. The samples were obtained by sulfidation of the Pb²⁺ ion-exchanged zeolite in a thiourea solution at 50 °C. The optical properties of the samples were studied by diffuse reflectance spectroscopy. Their crystalline structure and morphology were studied by electron diffraction and by transmission and scanning electron microscopy. The results show that the nanoparticles are not inside the zeolite cages but outside, embedded in the zeolite matrix. Exciton absorption peaks at much higher energy than the fundamental absorption edge of bulk PbS indicate quantum confinement effects in the spherical shape nanoparticles as a consequence of their small size.     

Low temperature formation of multi-layered structures of ferromagnetic silicide Fe3Si and Ge

Low-temperature (<300 °C) molecular beam epitaxy of Fe₃Si/Ge was investigated. By optimizing growth conditions, Fe₃Si layers with a flat interface and good crystallinity were epitaxially grown on Ge(1 1 1) substrates. In addition, double heteroepitaxial growth of Fe₃Si/Ge on high quality Fe₃Si/Ge substrates was investigated. Reflective high-energy electron diffraction measurements suggested Fe₃Si and Ge layers were epitaxially grown on Fe₃Si/Ge substrates. However, transmission electron microscopy measurements indicated stacking faults formed in the intermediate Ge and top Fe₃Si layers. Improved crystallinity of the intermediate Ge layer is essential to realize high quality [Fe₃Si/Ge]₂ multi-layered structures.     

Electrically Driven InAs Quantum-Dot Single-Photon Sources

Electrically driven single photon source based on single InAs quantum dot （QDs） is demonstrated. The device contains InAs QDs within a planar cavity formed between a bottom AlCaAs/CaAs distributed Bragg reflector （DBR） and a surface CaAs-air interface. The device is characterized by I-V curve and electroluminescence, and a single sharp exciton emission line at 966nm is observed. Hanbury Brown and Twiss （HBT） correlation measurements demonstrate single photon emission with suppression of multiphoton emission to below 45% at 80 K     

InSb quantum dots and quantum rings on InAs-rich surface

We report a study of InSb nanoobjects (quantum dots and quantum rings) grown on InAs-rich surface by liquid phase epitaxy. Characterization of the sample surface was performed using atomic force microscopy (AFM). The bimodal formation of the uncapped InSb quantum dots (QDs) was observed for the growing on a binary InAs substrate. Uniform high-density (1 × 10¹⁰ cm⁻²) quantum dots with a height of 3 nm were obtained at T = 420-430 °C, whereas low-density (5 × 10⁸ cm⁻²) big quantum dots were 9 nm in height. As a buffer layer, lattice-matched InAsSb_0.12P_0.25 solid solution was deposed on InAs substrate using metal-organic vapour phase epitaxy. Deposition from the InSb melt on the buffer layer resulted in the formation of InSb nanoobjects with density as high as 3 × 10¹⁰ cm⁻².     

Island dissolution during capping layer growth interruption

A possible scenario for the dissolution of partially capped quantum dots was investigated. This model is based on the consideration of the total free energy being a sum of elastic and surface energies as the quantum-dot material redistributes itself as a second wetting layer on top of the capping layer. Quantitative results were obtained for the case of InAs/GaAs quantum dots that are partially capped by GaAs. We compare our results with supporting experimental evidence. Received: 29 January 2001 / Accepted: 30 January 2001 / Published online: 3 April 2001     

Arsenic beam from a MBE source characterized by femtosecond laser spectroscopy

4 are the constituents of a molecular beam. Of importance are parameters such as laser intensity, pulse duration, and laser wavelength for a quantitative characterization and thereby improvement of MBE sources. This would help to optimize the epitaxial growth process. We demonstrate that nonresonant multiphoton ionization (MPI) by fs laser pulses leads to detection of the parent molecule, whereas nonresonant MPI with ns laser pulses leads to strong fragmentation. Received: 8 August 1997/Revised version: 3 December 1997     

Effect of seed layer on the growth of well-aligned ZnO nanowires

We demonstrate that vertical well-aligned crystalline ZnO nanowire arrays were grown on ZnO/glass substrates by a low-temperature solution method. Different thicknesses of ZnO seed layers on glass substrates were prepared by radio-frequency sputtering. In this work it was found that the morphology of ZnO nanowires strongly depends on the thickness of ZnO seed layers. The average diameter of nanowires is increased from 50 to 130 nm and the nanowire density is decreased from 110 to 60 μm⁻² while the seed layer thickness is varied from 20 to 1000 nm. The improved control of the morphology of ZnO nanowire arrays may lead to an enhanced carrier collection of hybrid polymer photovoltaic devices based on ZnO.     

GaAs surface passivation by ultra-thin epitaxial GaP layer and surface As-P exchange

The GaAs surface passivation effects of epitaxially grown ultra-thin GaP layers and surface As-P exchange have been investigated. Optical properties of passivated and unpassivated InGaAs/GaAs near-surface quantum wells (QWs) grown by metal organic vapor phase epitaxy (MOVPE) are studied by low-temperature continuous-wave and time-resolved photoluminescence (PL). By optimizing the growth conditions, smooth surface morphologies and significant improvement of optical properties were observed for both passivation methods. Passivation improved the PL intensity more than two orders of magnitude and notably increased the PL decay time.     

Surface modification of exchange-coupled Co/NiOx magnetic bilayer by bias sputtering

We have investigated the effect of bias voltage on sheet resistance, surface roughness and surface coverage of Co/NiO_x magnetic bilayer. In addition, interface topography and corrosion resistance of the Ta/Co/Cu/Co/NiO_x/Si(1 0 0) system have been studied for Co layers deposited at an optimum bias voltage. Atomic force microscopy (AFM) and four point probe sheet resistance (R_s) measurement have been used to determine surface and electrical properties of the sputtered Co layer at different bias voltages ranging from 0 to −80 V. The Co/NiO_x bilayer exhibits a minimum surface roughness and low sheet resistance value with a maximum surface coverage at V_b=−60 V resulted in a slight increase of magnetic resistance and its sensitivity for the Co/Cu/Co/NiO_x/Si(1 0 0) magnetic multilayers, as compared with the same magnetic multilayers containing unbiased Co layers. The presence of Ta protection layer improves the corrosion resistance of the multilayers by three orders of magnitude in a humid environment.     

pH-dependent aggregation and photoluminescence behavior of thiol-capped CdTe quantum dots in aqueous solutions

pH-dependent aggregation of thiol-capped CdTe quantum dots (QDs) in solutions was observed with a confocal microscope. The average size of the QD aggregates increased from 28 nm to 1.4 μm as the pH decreased from 12 to 3. The basic condition improved the dispersion of QDs while the acidic condition caused the detachment of surface ligands, leading to the aggregation of QDs. A PL lifetime of 80 ns was detected for QDs at pH from 12 to 7, while it was shortened to 57 and 34 ns at pH 5 and 3, respectively, due to the formation of surface defects.     

Self-organized formation of shell-like InAs/GaAs quantum dot ensembles

Formation of a multimodal quantum dot (QD) ensemble by strained layer epitaxy of InAs on GaAs near the critical value for the onset of the 2D-3D transition is studied. Reflection anisotropy spectroscopy is employed to confirm that a smooth surface is maintained during strained layer growth prior to QD formation. Instantaneous capping after deposition leads to InAs quantum wells with some thickness flucuations. Multimodal QD InAs ensembles form after an at least short growth interruption prior to cap layer deposition. The QDs consist of pure InAs with heights varying in steps of complete InAs monolayers. Related exciton energies indicate a simultaneous increase of both height and lateral extension, i.e. a shell-like increase of sizes. The formation of the multimodal QD ensemble is described by a kinetic approach. A growth scenario is presented where QDs having initially shorter base length stop vertical growth at a smaller height, accounting for the experimentally observed shell-like sub-ensemble structure.