Biological UV dosimeters in the assessment of the biological hazard from environmental radiation

To determine the impact of environmental UV radiation, biological dosimeters that weight directly the incident UV components of sunlight have been developed, improved and evaluated in the frame of the BIODOS project. Four DNA-based biological dosimeters ((i) phage T7, (ii) uracil thin layer, (iii) spore dosimeter and (iv) DLR-biofilm) have been assessed from the viewpoint of their biological relevance, spectral response and quantification of their biological effectiveness. The biological dosimeters have been validated by comparing their readings with weighted spectroradiometer data, by comparison with other biological doses, as well as with the determined amounts of DNA UV photoproducts. The data presented here demonstrate that the biological dosimeters are potentially reliable field dosimeters for measuring the integrated biologically effective irradiance for DNA damage.     

UV dosimeters based on neotetrazolium chloride

A novel UV dosimeter is described comprising a tetrazolium dye, neotetrazolium chloride (NTC), dissolved in a film of polymer, polyvinyl alcohol (PVA). The dosimeter is pale yellow/colourless in the absence of UV light, and turns red upon exposure to UV light. The spectral characteristics of a typical UV dosimeter film and the mechanism through which the colour change occurs are detailed. The NTC UV dosimeter films exhibit a response to UV light that is related to the intensity and duration of UV exposure, the level of dye present in the films and the thickness of the films themselves. The response of the dosimeter is temperature independent over the range 20–40 °C and, like most UV dosimeters, exhibits a cosine-like response dependence upon irradiance angle. The introduction of a layer of a UV-screening compound which slows the rate at which the dosimeter responds to UVR enables the dosimeter response to be tailored to different UV doses. The possible use of these novel dosimeters to measure solar UV exposure dose is discussed.     

A critical assessment of two types of personal UV dosimeters

Doses of erythemally weighted irradiances derived from polysulphone (PS) and electronic ultraviolet (EUV) dosimeters have been compared with measurements obtained using a reference spectroradiometer. PS dosimeters showed mean absolute deviations of 26% with a maximum deviation of 44%, the calibrated EUV dosimeters showed mean absolute deviations of 15% (maximum 33%) around noon during several test days in the northern hemisphere autumn. In the case of EUV dosimeters, measurements with various cut-off filters showed that part of the deviation from the CIE erythema action spectrum was due to a small, but significant sensitivity to visible radiation that varies between devices and which may be avoided by careful preselection. Usually the method of calibrating UV sensors by direct comparison to a reference instrument leads to reliable results. However, in some circumstances the quality of measurements made with simple sensors may be over-estimated. In the extreme case, a simple pyranometer can be used as a UV instrument, providing acceptable results for cloudless skies, but very poor results under cloudy conditions. It is concluded that while UV dosimeters are useful for their design purpose, namely to estimate personal UV exposures, they should not be regarded as an inexpensive replacement for meteorological grade instruments.     

Investigation of some commercial TLD chips/discs as UV dosimeters

Using a deuterium UV source, we have investigated the response of a number of commercially available thermoluminescence (TL) dosimeters (TLDs) to UV radiation (UVR), including LiF : Mg, Cu, P (TLD-100 H), CaF₂ : Dy (TLD-200), CaF₂ : Mn (TLD-400), Al₂O₃ (TLD-500), ⁷LiF : Mg, Cu, P (TLD-700 H) and CaSO₄ : Dy (TLD-900). The intrinsic method was used to detect UVR, while trap depth and frequency factors were estimated using the initial rise method. We have studied TL intensity as a function of exposure time, observing high sensitivity of TLD-500 to UVR. Conversely, TLD-400 displays weak sensitivity to these same radiations. Although TLD-900 and TLD-200 are both less sensitive to UVR than TLD-500, they each provide a linear response to UVR. The possible use of these phosphors as UV dosimeters has been further appraised, examining thermal fading effects and fading due to light exposure.     

Trends in UV irradiance of tanning devices in Norway: 1983-2005

Abstract Indoor tanning increases skin cancer risk, but the importance of different parts of the UV spectrum is unclear. We assessed irradiance of tanning devices in Norway for the period 1983-2005. Since 1983, all tanning models needed approval before being sold or used. UV Type 3 limits were valid from late 1992 (<0.15 W m(-2) for CIE-weighted, i.e. erythemally weighted, short and long wave irradiances). We analyzed data from 90% of the approved tanning models (n = 446 models) and two large inspection surveys in 1998/1999 and 2003 (n = 1341 tanning devices). Mean CIE-weighted short wave irradiance of approved models increased from 0.050 W m(-2) (95% confidence interval [CI] 0.045-0.055) in 1983-1992 to 0.101 W m(-2) (95% CI 0.098-0.105) in 1993-2005, and mean long wave from 0.091 W m(-2) (95% CI 0.088-0.095) to 0.112 W m(-2) (95% CI 0.109-0.115), respectively. Inspection surveys revealed short wave irradiances much higher than that approved. In 1998-1999, only 28% (293/1034) of the devices were equipped with correct sunlamps and only 1 out of 130 inspected establishments fulfilled all requirements. In 2003, corresponding numbers were 59% (180/307) of devices and 2 out of 52 establishments. Mean short and long wave irradiances of the inspected tanning devices in 2003 were 1.5 and 3.5 times, respectively, higher than the irradiance of natural summer sun in Oslo. In conclusion, the short wave irradiance has increased in indoor tanning devices in Norway over the last 20 years. Due to the high long wave irradiance throughout this period, the percentage of short wave irradiance was much lower than for natural sun.     

Retinal phototoxicity induced by hydrochlorothiazide after exposure to a UV tanning device

Abstract UV radiation is known to cause acute and chronic eye and skin damage. The present case report describes the occurrence of hydrochlorothiazide-induced retinal phototoxicity immediately after exposure to UV light emanated from a sunbed in a 40-year-old myopic woman. During the tanning session she had always worn UV protective eyewear, except for a few minutes when she took the protective goggles off to put her spectacles on to locate and turn the timer switch off. At baseline her visual acuity was 10/25 in OD and 10/80 in OS. Fundus examination revealed the presence of retinal lesions in both eyes. More specific tests confirmed the presence of a phototoxic macular damage. Hydrochlorothiazide was discontinued, and she was recommended to wear UV filtering glasses. Over the follow-up period (12 months), a slow and progressive visual acuity recovery in both eyes occurred. At the last check the visual acuity improvement was of about 60% from baseline in both eyes. Fundus examination showed only a juxtafoveal flat pigmented scar of the retinal pigment epithelium in both eyes, milder in OD. The constant rise in the number of sunbed users makes the knowledge of UV-related side effects a problem that cannot be postponed further. Awareness of the general public about the harmful effects of UV exposure must represent one of the leading preventive health strategies. Therefore, a careful analysis of the medical history before the admission to a sunbed session throughout a questionnaire could represent an economic and effective measure to avoid further cases of a phototoxic macular damage in patients taking photosensitizing compounds.     

Estimation of biologically damaging UV levels in marine surface waters with DNA and viral dosimeters

We have surveyed the biologically harmful radiation penetrating the water column along a transect in the western Gulf of Mexico using dosimeters consisting of intact viruses or naked calf-thymus DNA (ctDNA). The indigenous marine bacteriophage PWH3a-P1, which lytically infects the heterotrophic bacterium Vibrio natriegens (strain PWH3a), displayed decay rates for infectivity approaching 1.0 h(-1) in surface waters when deployed in a seawater-based dosimeter. The accumulation of pyrimidine dimers in ctDNA dosimeters provided a strong correlation to these results, with pyrimidine dimers representing more than 0.3% (up to ca 3800 dimers Mb(-1) DNA) of the total DNA in dosimeters exposed to sea surface levels of solar radiation. The results demonstrate a strong correlation between the dimer formation in the DNA dosimeters, the decay rates of viral infectivity and the penetration of UVB radiation into the water column. The decay of viral infectivity attenuated with depth in a manner similar to the decay of solar radiation and was still significant at 10 m in offshore oligotrophic water and at dimer frequencies less than 0.1% (ca 200-300 dimers Mb(-1) DNA).     

Biological and radiochemical quality control of indigenous99mTc-radiopharmaceutical kits

Biological and radiochemical quality control of indigenous (Pinscan) diagnostic cold kits of Methylene Diphosphonate (MDP), Tin-colloid and Diethylene Triamine Pentaacetic Acid (DTPA) was performed in parallel with imported Amersham's kits (Amerscan). The results of radiochemical purity, sterility, apyrogenicity and biodistribution of indigenous (Pinscan) kits were good and quantitatively and qualitatively comparable to those obtained with Amersham's (Amerscan) imported kits.     

The role of the spectral sensitivity curve in the selection of relevant biological dosimeters for solar UV monitoring

To estimate the risk of enhanced UV-B radiation due to stratospheric ozone depletion, phage T7 and uracil thin-layer biological dosimeters have been developed, which weight the UV irradiance according to induced DNA damage. To study the molecular basis of the biological effects observed after UV irradiation, the spectral sensitivity curves of the two dosimeters and induction of the two major DNA photoproducts, cyclobutane pyrimidine dimers (CPDs) and 6-4 photoproducts ((6-4)PDs), in phage T7 have been determined for polychromatic UV sources. CPDs and (6-4)PDs are determined by lesion-specific monoclonal antibodies in an immunodotblot assay. Phage T7 and uracil biological dosimeters together with a Robertson-Berger (RB) meter have been used for monitoring environmental radiation from the polar region to the equator. The biologically effective dose (BED) established with the three different dosimeters increases according to the changes in the solar angle and ozone column, but the degree of the change differs significantly. The results can be explained based on the different spectral sensitivities of the dosimeters. A possible method for determining the trend of the increase in the biological risk due to ozone depletion is suggested.     

Biological control of cellulose

The enhancement of bacterial cellulose (BC) productivity using sucrose as a carbon source has been obtained by the co-cultivation of two different types of acetic acid bacteria. BC yields for the given mix ratio of bacteria were larger than that of control. The contents of water-soluble polymer (WSP) in the BC composites (BCCs) are a range of 5–30 wt-%. This will be due to the formation of glucose and fructose through the hydrolysis of sucrose by sucrase secreted from Acetobacter sp. In addition, this preparation method would be applied to synthesize a new type of BC having both high biodegradability and other functions.     

Biological control of fungal pathogens

Biological control of soil-borne plant pathogens is a potential alternative to the use of chemical pesticides, which have already been proved to be harmful to the environment. Several strains of the fungusTrichoderma have been isolated and found to be effective biocontrol agents of various soil-borne plant pathogenic fungi under greenhouse and field conditions. Different application approaches have been used including integration ofTrichoderma with reduced doses of chemical agents. Biochemical and molecular biology studies carried out to explore the mechanisms involved in biological control revealed thatTrichoderma is a rather specific mycoparasite. Lectins were found to be involved in the recognition betweenTrichoderma and its host fungi, whereas chitinase is involved in the degradation of the host cell wall. Genetic engineering techniques were employed in order to increase the effectiveness, stability, and biocontrol capacity ofTrichoderma spp. as well as other biocontrol agents, such asPseudomonass spp. andRhizobium.     

Matrix effect in second-order data: determination of dyes in a tanning process using vegetable tanning agents

The aim of this paper is to determine the concentration of three dyes throughout the tanning process of leather using vegetable tanning agents with a sequential injection analyser with second-order data treatment. As the vegetable tanning agents used are highly absorbent species, we focus on three aspects: (i) difficulties with the resolution (ii) the reduction in the working concentration range; and (iii) matrix effects. Ideally, second-order instruments provide “second-order advantage”; i.e. calibration is possible in the presence of uncalibrated interfering species. However, if the interfering species change the instrumental response of the analyte (in scale or shape), standard additions must be used to ensure the accuracy of the estimated analyte concentration. Here we study the presence of matrix effects for three dyes in several samples in order to significantly improve the accuracy of predictions in the presence of such effects. We found that there were matrix effects in at least 80% of the samples with an alpha risk of 5%. We used this method to study the exhaustion of dyes in the dyeing process.     

TOC versus UV spectrophotometry for wastewater quality monitoring

Total organic carbon (TOC) is one of the most important parameter for the knowledge of water and wastewater quality, because it concerns theoretically all organic compounds. Unfortunately, some restrictions with respect to TOC measurement must be considered, explaining that alternative procedures have been envisaged, among which UV spectrophotometry. Starting from a comparison of results between high temperature digestion and UV photo-oxidation techniques for some specific compounds and real wastewater samples, the work shows the complementary interest of using UV spectrophotometry either directly (with multiwavelength procedures) or after UV photo-oxidation.     

Vegetable tanning substances. Dependence of the tanning properties of extracts on their composition

Information is given on vegetable tanning substances, their classification, distribution in the plant world, and structure, and the dependence of their tanning properties on their composition, and also on methods of enriching tanning extracts. The review of literature sources includes publications from 1950 to 1989.A. S. Sadykov Institute of Bioorganic Chemistry, Uzbek SSR Academy of Sciences, Tashkent. Translated from Khimiya Prirodnykh Soedinenii, No. 3, pp. 293–307, May–June, 1990.     

Vegetable tanning substances. Dependence of the tanning properties of extracts on their composition

Information is given on vegetable tanning substances, their classification, distribution in the plant world, and structure, and the dependence of their tanning properties on their composition, and also on methods of enriching tanning extracts. The review of literature sources includes publications from 1950 to 1989.     

Selfcalibrated alanine/EPR dosimeters: A new generation of solid state/EPR dosimeters

Alanine/EPR dosimeters are well established as secondary, reference dosimeters for high-energy radiation. However, there are various sources of uncertainty in the evaluation of absorbed dose. This arises primarily from the necessity to calibrate each EPR spectrometer and each batch of dosimeters before their use. In order to overcome this disadvantage, a new generation alanine/EPR dosimeter has been developed, and its possibilities as a radiation detector are reported. Principally, it is a mixture of alanine, some quantity of EPR active substance, and a binding material. The EPR active substance, acting as an internal EPR standard, is chosen to have EPR parameters which are independent of the irradiation dose. The simultaneous recording of the spectra of both the sample and the standard under the same experimental conditions and the estimation of the ratioI _alanine/I _Mn as a function of the absorbed dose strongly reduces the uncertainties. The response of these dosimeters for⁶⁰Co γ-radiation exhibits excellent linearity and reproducibility in the range of absorbed dose, 10²−5·10⁴ Gy.     

Biological responses to the simulated Martian UV radiation of bacteriophages and isolated DNA

Mars is considered as a main target for astrobiologically relevant exploration programmes. In this work the effect of simulated Martian solar UV radiation was examined on bacteriophage T7 and on isolated T7 DNA. A decrease of the biological activity of phages, characteristic changes in the absorption spectrum and in the electrophoretic pattern of isolated DNA/phage and the decrease of the amount of PCR products were detected indicating damage of isolated and intraphage T7 DNA by UV radiation. Further mechanistic insights into the UV-induced formation of intraphage/isolated T7 DNA photoproducts were gained from the application of appropriate enzymatic digestion and neutral/alkaline agarose gel electrophoresis. Our results showed that intraphage DNA was about ten times more sensitive to simulated Martian UV radiation than isolated T7 DNA indicating the role of phage proteins in the DNA damage. Compared to solar UV radiation the total amount of DNA damage determined by QPCR was about ten times larger in isolated DNA and phage T7 as well, and the types of the DNA photoproducts were different, besides cyclobutane pyrimidine dimers (CPD), double-strand breaks (dsb), and single-strand breaks (ssb), DNA-protein cross-links were produced as well. Surprisingly, energy deposition as low as 4-6eV corresponding to 200-400nm range could induce significant amount of ssb and dsb in phage/isolated DNA (in phage the ratio of ssb/dsb was approximately 23%/12% and approximately 32%/19% in isolated DNA). 5-8% of the CPD, 3-5% of the AP (apurinic/apyrimidinic) sites were located in clusters in DNA/phage, suggesting that clustering of damage occur in the form of multiple damaged sites and these can have a high probability to produce strand breaks. The amount of total DNA damage in samples which were irradiated in Tris buffer was reduced by a factor approximately 2, compared to samples in phosphate buffer, suggesting that some of the photoproducts were produced via radicals.     

A proficiency test scheme for the quality control of black tea and development of quality control material for internal quality control

A proficiency test (PT) was organized for quality control analysis of black tea. Test materials for the analyses of total content of powder tea, moisture, total ash, acid-insoluble ash, water-soluble ash, alkalinity of water-soluble ash, water extract, crude fiber and caffeine were sent to the participant laboratories (n:43) in 2009. The assigned value, standard deviation of the parameters and z-scores of the participant laboratories were calculated using the data reported by the participants. The percentage of the reported results for analytes was found to be ranged from 67.5 to 100%. Acceptable z-scores were achieved by 80.5–97.5% of the participant laboratories. More than 15% of unacceptable results were obtained for acid-insoluble ash and caffeine analyses. The quality control material for quality control analysis of black tea was developed from the remaining material.     

Management of quality control in analytical laboratories

The sources of errors in the results of chemical analysis are classified. Methods for the on-line control of the precision and accuracy of analysis are briefly discussed and compared in order to reveal the types of sources of errors in the considered methods. Algorithms to estimate the quality of work of an analytical laboratory based on the statistical analysis of the summarized results of control obtained in a certain period of time are proposed.     

Capillary electrophoresis speciation of chromium in leather tanning liquor

We present a method for the speciation of chromium by capillary electrophoresis. Cr(III) was complexed with diethylenetriaminepentaacetic acid (DTPA) to form a negatively charged complex. Using 20 mM phosphate buffer of pH 8 containing 0.5 mM tetradecyltrimethylammonium hydroxide (TTAOH) at a separation voltage of -15 kV, both forms of chromium CrDTPA(2-) and CrO(4) (2-) were separated in less than 6 min. Direct UV detection at 214 nm was used. The effect of the presence of interfering ions was investigated. The application of the developed method to speciation of chromium in tanning liquor is demonstrated. The obtained results have shown a good correlation with those of flame atomic absorbance spectrometry (FAAS), inductively coupled plasma-mass spectrometry (ICP-MS) and UV/VIS spectrophotometry.