Preparation of SiO2–wood composites by an ultrasonic-assisted sol–gel technique

The vacuum impregnation assisted sol–gel technique is a promising and environmentally-friendly method for the inorganic modification of wood by the formation of wood-inorganic composites. However, vacuum impregnation is relatively cumbersome and time-consuming. In this study, SiO₂–wood composites were prepared by an ultrasonic-assisted sol–gel method, which is an innovative and simple method. Using this method, we found an increase in the degree of silicon incorporation into the cell walls of the wood. The impregnation of silica inside the cell walls were verified by Fourier-transform infrared spectra, X-ray diffraction, scanning electron microscopy and energy dispersive spectrometry. Leaching test proved that the internal cross-linking silica is stably bonded to the wood cell walls. This modified method significantly reduced the hygroscopicity of the wood and consequently improved the mechanical performance of the modified wood. Thermogravimetric and differential thermal analyses showed that the incorporation of silicon retards thermal decomposition and the complete combustion of the wood matrix and it enhances the thermal stability of wood.     

Synthesis and characterization of nanocrystalline tin oxide by sol–gel method

Nanocrystalline SnO₂ particles have been synthesized by a sol–gel method from the very simple starting material granulated tin. The synthesis leads a sol–gel process when citric acid is introduced in the solution obtained by dissolving granulated tin in HNO₃. Citric acid has a great effect on stabilizing the precursor solution, and slows down the hydrolysis and condensation processes. The obtained SnO₂ particles range from 2.8 to 5.1 nm in size and 289–143 m² g⁻¹ in specific surface area when the gel is heat treated at different temperatures. The particles show a lattice expansion with the reduction in particle size. With the absence of citric acid, the precursor hydrolyzes and condenses in an uncontrollable manner and the obtained SnO₂ nanocrystallites are comparatively larger in size and broader in size distribution. The nanocrystallites have been characterized by means of TG-DSC, FT-IR, XRD, BET and TEM.     

Synthesis and characterization of nanostructured aluminum borate by sol–gel method

Nanostructured aluminum borate was synthesized using sol?Cgel technique. X-ray diffraction study revealed that the synthesized aluminum borate was single crystal. These nanorods have very uniform diameter. High-resolution transmission electron microscope images indicate that aluminum borate is well crystallized. The alternating current (AC) conductivity of the aluminum borate was studied as a function of temperature and frequency. The AC conductivity mechanism of the aluminum borate was found to be proportional to ??^s. The exponent s is almost independent with temperature. This suggests that AC conductivity mechanism of the aluminum borate can be interpreted by localized hopping model.     

Synthesis and characterization of lead oxide nano-powders by sol–gel method

Our goal in this research was to obtain lead oxide nano-powders by sol–gel method. In this method, lead oxide nano-powders were synthesized through the reaction of citric acid (C₆H₇O₈·H₂O) solution and lead acetate [Pb(C₂H₃O₂)₂] solution as stabilizer and precursor, respectively. The effect of different parameters including calcination temperature, (molar ratio of citric acid to lead acetate) and drying conditions were investigated. The prepared lead oxide nano-powders were characterized by FT-IR spectroscopy, X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. The prepared PbO samples consist of the particles in the range of 50–120 nm or the thick plate like structures with thickness of 53 nm depending on the drying conditions.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Synthesis of polyferromethylsiloxane sorbents using a sol–gel method

Trivalent iron complexes which could be easily converted into materials are formed by the reaction of FeCl₃ with K₃[O₃SiMe] in a highly concentrated aqueous alkaline solution. The presence of the liquid glass as an additive and decreasing the pH results in solutions that give rise to homogeneous gels. Polycondensation proceeds very rapidly in the higher pH range (viz. pH 9–10) and substantially slower in an acidic medium (pH 2–3). Xerogels were obtained having microporous structure after treatment of polyferromethylsiloxane gels obtained from acidic medium or mesoporous structure when obtained from alkaline medium.     

Synthesis and characterization of tellurium-doped CdO nanoparticles thin films by sol–gel method

In this work, tellurium (Te) doped CdO nanoparticles thin films with different Te concentrations (1, 3, 5, 7 and 10 %) were prepared by sol–gel method. The effects of Te doping on the structural, morphological and optical properties of the CdO thin films were systematically studied. From X-ray diffraction spectra, it has seen that all of thin films were formed polycrystalline and cubic structure having (111), (200) and (311) orientations. The structure of CdO thin films with Te-dopant was formed the unstable CdTeO₃ monoclinic structure crystal plane ( $ {\bar{\text{1}}\text{22}} $ 1 ¯ 22 ), however, the intensity of this unstable peak of the crystalline phase decreased with the increase of Te-doping ratio. The strain in the structure is also studied by using Williamson-Hall method. From FE-SEM images, it has seen that particles have homogeneously distributed and well hold onto the substrate surface. Additionally, grain size increases from 27 to 121 nm with the increase of Te-doping ratio. Optical results indicate that 1 % Te-doped CdO thin film has the maximum transmittance of about 87 %, and the values of optical energy band gap increases from 2.50 to 2.64 eV with the increase of Te-doping ratio. These results make Te-doped CdO thin films an attractive candidate for thin film material applications.     

Review of mullite synthesis routes by sol–gel method

The sol–gel method for the mullite synthesis is reviewed, with particular emphasis on the characterization of monophasic and diphasic gels at low, intermediate and high temperatures and the factors that influence the hydrolysis and condensation rate of the sol–gel process, which in turn determine the properties of the final material. A wide range of studies about mullite precursors synthesized via sol–gel is discussed here.     

Synthesis of sub-micro-sized solid alpha alumina fibers with smooth surfaces by sol–gel method

Alumina sol containing nano-meter sized Al₂O₃ particles were synthesized using aluminum sec-butoxide and nitric acid as precursor and peptizing agent, respectively. Polyvinylpyrrolidone (PVP) was added to prevent particle growth and adjust sol viscosity. PVP/alumina hybrid fibers were drawn from the sol with a viscosity value in the range of 2,500–3,000 mPa.s. By guided through a temperature gradient tube furnace at a rate of 4 m/min, the wet PVP/alumina hybrid fibers were sufficiently dried. Sub-micro-sized pure alpha alumina fibers were obtained by sintering the dry hybrid fibers at 1,000 °C for 3 h. The organic matters were decomposed within a wide temperature range from 150 to 800 °C allowing the nano Al₂O₃ particles to gradually get together and form solid alumina fibers with smooth surfaces.     

Synthesis of HAP coating on galvanostatically treated stainless steel substrates by sol–gel method

Producing bioactive hydroxyapatite coatings on metallic implant materials combines the mechanical advantages of implant materials and biological affinity of the hydroxyapatite surface to the natural tissue. In this work, hydroxyapatite was synthesized on 316L stainless steel substrates via sol–gel method by using Ca(NO₃)₂·4H₂O and C₆H₁₅O₃P. In order to improve adherence of the coatings produced, the surface of the substrate was initially modified by electrodepositing nucleus of calcium phosphate compounds. Effect of aging time for preparation of the sol solution and coating characteristics were investigated. The phase compositions and structures of the coatings were characterized by X-ray diffractometry, and scanning electron microscopy was used to determine morphological characteristics of the coatings. Adhesion between the hydroxyapatite coating and the substrate was investigated by using scanning scratch tester. The coating produced on the modified surface by the sol solution aged for 24 h was found to prove better morphological and adhesion properties.     

Synthesis and characterization of hydroxyapatite obtained from different organic precursors by sol–gel method

The synthesis of four types of hydroxyapatite synthesized from calcium chloride and four different organic phosphites is presented. The method of synthesis chosen is the sol–gel route, which has a number of advantages compared to other methods, like the intimate contact between reactants and the milder synthesis conditions. The samples were thermally treated, the TG/DTG/DTA curves being obtained at four heating rates, namely: 7, 10, 12 and 15 °C min⁻¹. The samples were characterized before and after the thermal treatment using FT-IR analysis. The FT-IR spectra certified that the formed compounds represent hydroxyapatite. Based on the information from the TG curves and IR spectra interpretation, a reaction mechanism was proposed.     

Deposition of silica thin films formed by sol–gel method

Deposition of silica thin films on silicon wafer was investigated by in situ mass measurements with a microbalance configured for dip coating. Mass change was recorded with respect to deposition time when the substrate was fully immersed in the silica sol. Mass gain during deposition was higher than predicted from monolayer coverage of silica nano particles. This implied that deposition was facilitated by gelling of the nanoparticles on the substrate. The rate of deposition was enhanced by increasing the particle concentration in the sol and by decreasing the particle size from 12 to 5 nm. Increasing the salt concentration of the silica sol at constant pH enhanced the deposition of the silica particles. Reducing the pH of the sol from 10 to 6 decreased the deposition rate due to aggregation of the primary silica particles.     

Study of tri-layer antireflection coatings prepared by sol–gel method

Antireflective coatings (ARCs) on tri-layer thin film stacks were studied in this paper. Silica sols have been prepared by acid-catalyzed or base-catalyzed hydrolysis and condensation reactions of tetraethyl orthosilicate. Antireflective nanometric SiO₂/TiO₂ films are formed on both sides of the glass substrates by combining the sol–gel method and the dip-coating technique. Seen from the transmittance spectra of different films, a maximum light transmittance of 99.9% was obtained at the band of 300–800 nm. Scanning electron microscope (SEM) and atomic force microscopy (AFM) confirm the well-covered surface morphology. By the SEM observations we can see that the films are full of coverage on glass surface and containing no voids or cracks. The image root mean square roughness of the two types of ARCs provided by the AFM is 1.21 and 3.04 nm, respectively. Furthermore, a surface profiler was used to determine the thickness of each layer in the obtained multi-layer coating system.     

Synthesis of nanostructural Yttrium fluorosilicate glass ceramic via sol–gel method

Journal of Sol-Gel Science and Technology - The yttrium fluorosilicate glass ceramic pieces were prepared by sol–gel method starting from yttrium acetate, trifluoroacetic acid, and...     

Synthesis of a dysprosium aluminum garnet nanopowder via sol–gel method

A dysprosium aluminum garnet (DAG) nanopowder was synthesized by aqueous sol–gel method using Al powder, HCl and Dy(CH₃COO)₃·4H₂O as raw materials. The dried amorphous gel was heat treated in the range of 800–1,200 °C. The influence of heat treatment on crystallization and phase transformation of the dried gel was investigated using X-ray diffractometery, scanning electron microscopy, thermogravimetry and differential thermal analysis and Fourier transform infrared spectroscopy. It was shown that the gel calcined from 900 to 1,200 °C resulted in the formation of a crystalline DAG nanopowder with particle size distribution ranges from 26 to 98 nm.