Free convection heat transfer from a horizontal fin attached cylinder between confined nearly adiabatic walls

Steady state two-dimensional free convection heat transfer from a horizontal, isothermal fin attached cylinder, located between nearly two adiabatic walls is studied experimentally using a Mach–Zehnder interferometer. Effects of the walls inclination angel (θ) on heat transfer from the cylinder is investigated for Rayleigh number ranging from 1000 to 15,500. Two cylinders with different diameters of D = 10 and 20 mm are used to cover wide Rayleigh range. Results indicate that, heat transfer phenomena differ for different Rayleigh number. For Rayleigh numbers lower than 5500, heat transfer rate from cylinder surface is lower than the heat transfer from a single cylinder. In this range by the use of walls, heat transfer from the cylinder decreases slightly and walls’ inclination does not change heat transfer rate from the cylinder surface. For Rayleigh number ranging from 5500 to 15,500, amount of heat transfer from the cylinder surface is less than that of a single cylinder. However, by adding nearly adiabatic walls to experimental model heat transfer mechanism differs and chimney effect between fin and walls increases the heat transfer rate from the cylinder surface. By increasing the walls inclination angel from 0° to 20°, the chimney effect between walls and fin diminishes and heat transfer rate from the cylinder surface is approaching to the heat transfer rate of fin attached cylinder without adiabatic walls.     

Experimental investigation of natural convection in a vertical rib-roughened channel with asymmetric heating

An experimental study in an open-ended vertical channel is carried out in order to describe the fluid dynamics and heat transfer of transient free convection inside a vertical rib-roughened channel asymmetrically heated at various uniform heat fluxes (650, 700, and 780 W/m²) corresponding to various modified Rayleigh numbers (3.65 × 10⁶, 3.93 × 10⁶ and 4.4 × 10⁶). Two ribs are symmetrically located on each wall. The investigations focused more specifically on the influence of the ribs positions inside the channel and the modified Rayleigh number (Ra^*) both in steady-state regime and during the transitional phase occurring just after the start of the heating on the flow structure and the heat transfer performance. The results showed the appearance of large-scale flow instabilities which will develop and propagate until the development of the pocket-like vortex (reversed flow). Also, the formation and breakup of recirculation eddies, vortex banishment, besides that a separation and shifting of the boundary layer from one wall to another are identified. The best position of the ribs for heat extraction depends on the magnitude of the Rayleigh number. In that case, the top position is the optimal position for the small and the moderate modified Rayleigh numbers.     

Thermal study of an array of inline horizontal cylinders below a nearly adiabatic ceiling

Steady state two-dimensional free convection heat transfer from a horizontal, isothermal cylinder in a horizontal array of cylinders consists of three isothermal cylinders, located underneath a nearly adiabatic ceiling is studied experimentally. A Mach–Zehnder interferometer is used to determine thermal field and smoke test is made to visualize flow field. Effects of the cylinders spacing to its diameter (S/D), and cylinder distance from ceiling to its diameter (L/D) on heat transfer from the centered cylinder are investigated for Rayleigh numbers from 1500 to 6000. Experiments are performed for an inline array configuration of horizontal cylinders of diameters D = 13 mm. Results indicate that due to the nearly adiabatic ceiling and neighboring cylinders, thermal plume resulted from the centered cylinder separates from cylinder surface even for high L/D values and forming recirculation regions. By decreasing the space ratio S/D, the recirculation flow strength increases. Also, by decreasing S/D, boundary layers of neighboring cylinders combine and form a developing flow between cylinders. The strength of developing flow depends on the cylinders Rayleigh number and S/D ratio. Due to the developing flow between cylinders, the vortex flow on the top of the centered cylinder appears for all L/D ratios and this vortex influences the value of local Nusselt number distribution around the cylinder.Variation of average Nusselt number of the centered cylinder depends highly on L/D and the trend with S/D depends on the value of Rayleigh number.     

Conjugate turbulent heat transfer in a square cavity with a solar control coating deposited to a vertical semitransparent wall

This paper presents a numerical study of the conjugate heat transfer (natural convection, surface thermal radiation and conduction) in a square cavity with turbulent flow. The cavity has one vertical isothermal wall, two horizontal adiabatic walls and one vertical semitransparent wall with a selective coating applied to the inner side to control the solar radiation transmission. Later on the semitransparent wall is replaced with another one without the selective coating. The mathematical model for the turbulent flow in the cavity was solved using the finite volume method. The system had the following conditions: the uniform temperature in the isothermal wall was 21 °C, the external ambient temperature was fixed at 35 °C and on the semitransparent wall the direct normal solar irradiation of 750 W/m² was considered constant. The Rayleigh number was varied in the range of 10⁹ ? Ra ? 10¹² by changing the lengths of the cavity from 0.70 m to 6.98 m, respectively. The results show that, even though the air temperature of the cavity with the solar control film coating semitransparent wall (case A) is higher compared with the one without solar film coating (case B), the total amount of heat going through the cavity is lower compared to the one going through the cavity without solar control film. The total amount of energy transferred to the air in cavity for the case A was 41.98% less than for the case B. A set of correlations for the Nusselt number was obtained for both cases considering the conjugate heat transfer.     

Influence of aspect ratio on the flow above the free end of a surface-mounted finite cylinder

The flow above the free end of a surface-mounted finite-height cylinder was studied in a low-speed wind tunnel using particle image velocimetry (PIV). Velocity measurements were made in vertical and horizontal measurement planes above the free end of finite cylinders of aspect ratios AR = 9, 7, 5 and 3, at a Reynolds number of Re = 4.2 × 10⁴. The relative thickness of the boundary layer on the ground plane was δ/D = 1.7. Flow separating from the leading edge formed a prominent recirculation zone on the free-end surface. The legs of the mean arch vortex contained within the recirculation zone terminate on the free-end surface on either side of the centreline. Separated flow from the leading edge attaches onto the upper surface of the cylinder along a prominent attachment line. Local separation downstream of the leading edge is also induced by the reverse flow and arch vortex circulation within the recirculation zone. As the cylinder aspect ratio is lowered from AR = 9 to AR = 3, the thickness of the recirculation zone increases, the arch vortex centre moves downstream and higher above the free-end surface, the attachment position moves downstream, and the termination points of the arch vortex move upstream. A lowering of the aspect ratio therefore results in accentuated curvature of the arch vortex line. Changes in aspect ratio also influence the vorticity generation in the near-wake region and the shape of the attachment line.     

Lattice Boltzmann simulation of the convective heat transfer from a stream-wise oscillating circular cylinder

In this paper, we studied the convective heat transfer from a stream-wise oscillating circular cylinder. Two dimensional numerical simulations are conducted at Re = 100–200, A = 0.1–0.4 and F = f_o/f_s = 0.2–3.0 with the aid of the lattice Boltzmann method. In particular, detailed attentions are paid on the extensive numerical results elucidating the influence of oscillation frequency, oscillation amplitude and Reynolds number on the time-average and RMS value of the Nusselt number. Over the ranges of conditions considered herein, the heat transfer characteristics are observed to be influenced in an intricate manner by the value of the oscillation frequency (F), oscillation amplitude (A) and Reynolds number (Re). Firstly, the heat transfer is enhanced when the cylinder oscillates stream-wise with small amplitude and low frequency, while it will be reduced by large amplitude and high frequency. Secondly, the average Nusselt number (Nu (ave)) decreases against the increasing value of oscillation frequency, while the RMS value of the Nusselt number, Nu (RMS), displays an opposite trend. Third, we obtained a similar frequency effect on the heat transfer over the range of Reynolds numbers investigated in this paper. In addition, detailed analyses on phase portraits, energy spectrum are also made.     

The effect of corona discharge on free convection heat transfer from a horizontal cylinder

Free convection heat transfer from an isothermal horizontal cylinder in the presence of DC positive corona discharge with a blade edge emitter electrode has been studied experimentally and numerically. A Mach–Zehnder interferometer was used to determine the local Nusselt numbers. The effect of corona discharge on heat transfer from the cylinder was investigated at Rayleigh numbers in the range between 1500 and 5000. To find the details of the flow patterns and to further verify the experimental results, numerical simulations were also performed. It was found that the numerical results are in good agreement with experimental data. By increasing the applied voltage up to 15.5 kV, the corona discharge generates a recirculation zone around the blade and below the lower stagnation point of the cylinder. The effect of the recirculation zone becomes stronger near the breakdown voltage (17 kV) and it is responsible for a local decrease in the cooling of the cylinder around the lower stagnation point. The results indicate that corona discharge has a significant effect on the average Nusselt number at lower Rayleigh numbers whereas it has smaller effect at higher Rayleigh numbers.     

Effect of side ratio on fluid flow and heat transfer from rectangular cylinders using the PANS method

A computational study of heat transfer from rectangular cylinders is carried out. Rectangular cylinders are distinguished based on the ratio of the length of streamwise face to the height of the cross-stream face (side ratio, R). The simulations were performed to understand the heat transfer in a flow field comprising separation, reattachment, vortex shedding and stagnation. The Partially-Averaged Navier–Stokes (PANS) modeling approach is used to solve the turbulent flow physics associated and the wall resolve approach is used for the near wall treatment because of the flow separation involved. The simulations were performed using a finite volume based opensource software, OpenFOAM, at Reynolds number (Re) = 22,000 for rectangular cylinder at constant temperature kept in an air stream. Two critical side ratios were obtained, R = 0.62 and 3.0. At R = 0.62, the maximum value of the drag coefficient (C_d) = 2.681 was observed which gradually reduced by 54% at R = 4.0. The base pressure coefficient and global Nusselt number also attained the maximum value at R = 0.62 and from R = 2.5 to 3.0 a sharp discontinuous increase by 140% in the Strouhal number was observed. At R = 0.62, it was observed that the separated flow reattaches at the trailing edge after rolling over the side face and therefore increases the overall Nusselt number. The phase averaging was also performed to analyze the unsteady behavior of heat transfer.     

Instantaneous flow field above the free end of finite-height cylinders and prisms

The flow above the free ends of surface-mounted finite-height circular cylinders and square prisms was studied experimentally using particle image velocimetry (PIV). Cylinders and prisms with aspect ratios of AR = 9, 7, 5, and 3 were tested at a Reynolds number of Re = 4.2 × 10⁴. The bodies were mounted normal to a ground plane and were partially immersed in a turbulent zero-pressure-gradient boundary layer, where the boundary layer thickness relative to the body width was δ/D = 1.6. PIV measurements were made above the free ends of the bodies in a vertical plane aligned with the flow centreline. The present PIV results provide insight into the effects of aspect ratio and body shape on the instantaneous flow field. The recirculation zone under the separated shear layer is larger for the square prism of AR = 3 compared to the more slender prism of AR = 9. Also, for a square prism with low aspect ratio (AR = 3), the influence of the reverse flow over the free end surface becomes more significant compared to that for a higher aspect ratio (AR = 9). For the circular cylinder, a cross-stream vortex forms within the recirculation zone. As the aspect ratio of the cylinder decreases, the reattachment point of the separated flow on the free end surface moves closer to the trailing edge. For both the square prism and circular cylinder cases, the instantaneous velocity vector field and associated in-plane vorticity field revealed small-scale structures mostly generated by the separated shear layer.     

Separated flow structures around a cylindrical obstacle in a narrow channel

A detailed experimental study is performed on the separated flow structures around a low aspect-ratio circular cylinder (pin-fin) in a practical configuration of liquid cooling channel. Distinctive features of the present arrangement are the confinement of the cylinder at both ends, water flow at low Reynolds numbers (Re = 800, 1800, 2800), very high core flow turbulence and undeveloped boundary layers at the position of the obstacle. The horseshoe vortex system at the junctions between the cylinder and the confining walls and the near wake region behind the obstacle are deeply investigated by means of Particle Image Velocimetry (PIV). Upstream of the cylinder, the horseshoe vortex system turns out to be perturbed by vorticity bursts from the incoming boundary layers, leading to aperiodical vortex oscillations at Re = 800 or to break-away and secondary vorticity eruptions at the higher Reynolds numbers. The flow structures in the near wake show a complex three-dimensional behaviour associated with a peculiar mechanism of spanwise mass transport. High levels of free-stream turbulence trigger an early instabilization of the shear layers and strong Bloor–Gerrard vortices are observed even at Re = 800. Coalescence of these vortices and intense spanwise flow inhibit the alternate primary vortex shedding for time periods whose length and frequency increase as the Reynolds number is reduced. The inhibition of alternate vortex shedding for long time periods is finally related to the very large wake characteristic lengths and to the low velocity fluctuations observed especially at the lowest Reynolds number.     

Bow shocks formed by plasma collisions in laser irradiated semi-cylindrical cavities

The formation of shocks in plasmas created by short pulse laser irradiation (λ = 800 nm, I ≈ 1 × 10¹² W cm^?2) of semi-cylindrical cavities of different materials was studied combining visible and soft X-ray laser interferometry with simulations. The plasma rapidly converges near the axis to form a dense bright plasma focus. Later in time a long lasting bow shock is observed to develop outside the cavity, that is shown to arise from the collision of plasmas originating from within the cavity and the surrounding flat walls of the target. The shock is sustained for tens of nanoseconds by the continuous arrival of plasma ablated from the target walls. The plasmas created from the heavier target materials evolve more slowly, resulting in increased shock lifetimes.     

Influence of single rectangular groove on the flow past a circular cylinder

In the present study, flow control mechanism of single groove on a circular cylinder surface is presented experimentally using Particle image velocimetry (PIV). A square shaped groove is patterned longitudinally on the surface of the cylinder with a diameter of 50 mm. The flow characteristics are studied as a function of angular position of the groove from the forward stagnation point of the cylinder within 0° ≤ θ ≤ 150°. In the current work, instantaneous and time-averaged flow data such as vorticity, ω streamline, Ψ streamwise, u/U_o and transverse, v/U_o velocity components, turbulent kinetic energy, TKE and RMS of streamwise, u_rms and transverse, v_rms velocity components are utilized in order to present the results of quantitative analyses. Furthermore, Strouhal numbers are calculated using Karman vortex shedding frequency, f_k obtained from single point spectral analysis. It is concluded that a critical angular position of the groove, θ = 80° is observed. The flow separation is controlled within 0° ≤ θ < 80°. At θ = 80°, the flow separation starts to occur in the upstream direction. The instability within the shear layer is also induced on grooved side of the cylinder with frequencies different than Karman vortex shedding frequency, f_k.     

Periodic boiling in parallel micro-channels at low vapor quality

Based on experimental investigations the present study evaluates instability and heat transfer phenomenon under condition of periodic flow boiling of water and ethanol in parallel triangular micro-channels. Tests were performed in the range of hydraulic diameter 100–220 μm, mass flux 32–200 kg/m² s, heat flux 120–270 kW/m², vapor quality x = 0.01–0.08. The period between successive events depends on the boiling number and decreases with an increase in the boiling number. The initial film thickness decreases with increasing heat flux. When the liquid film reached the minimum initial film thickness CHF regime occurred. Temporal variations of pressure drop, fluid and heater temperatures were periodic. Oscillation frequency is the same for the pressure drop, for the fluid temperature at the outlet manifold, and for the mean and maximum heater temperature fluctuations. All these fluctuations are in phase. The CHF phenomenon is different from that observed in a single channel of conventional size. A key difference between micro-channel heat sink and single conventional channel is amplification of parallel-channel instability prior to CHF. The dimensionless experimental values of the heat transfer coefficient are presented as the Nusselt number dependence on the Eotvos number and the boiling number.     

CFD simulation of a gas–solid fluidized bed with two vertical jets

A computational fluid dynamics (CFD) model is used to investigate the hydrodynamics of a gas–solid fluidized bed with two vertical jets. Sand particles with a density of 2660 kg/m³ and a diameter of 5.0 × 10^?4 m are employed as the solid phase. Numerical computation is carried out in a 0.57 m × 1.00 m two-dimensional bed using a commercial CFD code, CFX 4.4, together with user-defined Fortran subroutines. The applicability of the CFD model is validated by predicting the bed pressure drop in a bubbling fluidized bed, and the jet detachment time and equivalent bubble diameter in a fluidized bed with a single jet. Subsequently, the model is used to explore the hydrodynamics of two vertical jets in a fluidized bed. The computational results reveal three flow patterns, isolated, merged and transitional jets, depending on the nozzle separation distance and jet gas velocity and influencing significantly the solid circulation pattern. The jet penetration depth is found to increase with increasing jet gas velocity, and can be predicted reasonably well by the correlations of Hong et al. (2003) for isolated jets and of Yang and Keairns (1979) for interacting jets.     

The effects of freestream turbulence on the drag coefficient of a sphere

The effects of freestream turbulence intensity and integral length scale as freestream turbulent parameters on the drag coefficient of a sphere were experimentally investigated in a closed circuit wind tunnel. The Reynolds number, Re = Ud/ν, was varied from 2.2 × 10⁴ to 8 × 10⁴ by using spheres with diameter d of 20, 51 and 102 mm in addition to altering the freestream velocity, U. The freestream turbulence intensity Tu and flow integral length scale Λ were manipulated by the utilization of orifice perforated plates. The proper combination of orifice perforated plate hole diameter, sphere size, and sphere location along the center line of the wind tunnel enabled the independent alterations of turbulence intensity and relative integral length scale (Λ/d) from 1.8% to 10.7% and from 0.1 to 2.6, respectively, at each studied Reynolds number. Results show that over the range of conditions studied, the drag always decreases with increasing Tu and, the critical Reynolds number at which the drag coefficient is dramatically reduced is decreased by increasing Tu. Most interestingly, the drag at any particular Re and Tu may be significantly lowered by reducing Λ/d; this is particularly the case at high Re and Tu.     

Augmentation of heat transfer from heat source placed downstream a guide fence: An experimental study

The present study investigated experimentally the heat transfer from a heat source simulating an electronic chip mounted on a printed circuit board placed downstream of a guide fence on the lower wall of the flow passage with two different aspect ratios (H/W = 0.3 and 1). The channel height to the heat source height ratios (H/B) are of 10 and 3. The effect of the guide fence height (b) and the spacing between the guide fence and the heat source (S) were investigated. The guide fence was orientated such that guide fence extension point was varied from the midpoint of the front face of the heat source to the endpoint of the side face at 5000 ? Re_L ? 30,000. The results for the heat source without guide fence displayed noticeable difference when compared with the flow over smooth plate placed on the lower wall of the flow passage. An enhancement in the convective heat transfer coefficient up to 20% is obtained when decreasing the flow passage height to the heat source height ratio from 10 to 3. Also, higher Nusselt number is located at the front face and the vertical sides of the heat source compared with that of the top surface. Nusselt number increases with the increase in both Reynolds number and the guide fence height while the effect of spacing between the guide fence and the heat source depending on the guide fence height. Correlations for the average Nusselt number were obtained utilizing the present measurements within the investigated range of the different parameters.     

A numerical study of steady and unsteady viscoelastic flow past bounded cylinders

We consider two-dimensional, inertia-free, flow of a constant-viscosity viscoelastic fluid obeying the FENE-CR equation past a cylinder placed symmetrically in a channel, with a blockage ratio of 0.5. Through numerical simulations we show that the flow becomes unsteady when the Deborah number (using the usual definition) is greater than De ≈ 1.3, for an extensibility parameter of the model of L² = 144. The transition from steady to unsteady flow is characterised by a small pulsating recirculation zone of size approximately equal to 0.15 cylinder radius attached to the downstream face of the cylinder. There is also a rise in drag coefficient, which shows a sinusoidal variation with time. The results suggest a possible triggering mechanism leading to the steady three-dimensional Gortler-type vortical structures, which have been observed in experiments of the flow of a viscoelastic fluid around cylinders. The results reveal that the reason for failure of the search for steady numerical solutions at relatively high Deborah numbers is that the two-dimensional flow separates and eventually becomes unsteady. For a lower extensibility parameter, L² = 100, a similar recirculation is formed given rise to a small standing eddy behind the cylinder which becomes unsteady and pulsates in time for Deborah numbers larger than De ≈ 4.0–4.5.     

Evaluation of subgrid-scale models in large-eddy simulation of flow past a two-dimensional block

Large-eddy simulations of flow past a two-dimensional (2D) block were performed to evaluate four subgrid-scale (SGS) models: (i) the traditional Smagorinsky model, (ii) the Lagrangian dynamic model, (iii) the Lagrangian scale-dependent dynamic model, and (iv) the modulated gradient model. An immersed boundary method was employed to simulate the 2D block boundaries on a uniform Cartesian grid. The sensitivity of the simulation results to grid refinement was investigated by using four different grid resolutions. The velocity streamlines and the vertical profiles of the mean velocities and variances were compared with experimental results. The modulated gradient model shows the best overall agreement with the experimental results among the four SGS models. In particular, the flow recirculation, the reattachment position and the vertical profiles are accurately reproduced with a relative coarse grid resolution of (N_x × N_y × N_z=) 160 × 40 × 160 (n_x × n_z = 13 × 16 covering the block). Besides the modulated gradient model, the Lagrangian scale-dependent dynamic model is also able to give reasonable prediction of the flow statistics with some discrepancies compared with the experimental results. Relatively poor performance by the Lagrangian dynamic model and the Smagorinsky model is observed, with simulated recirculating patterns that differ from the measured ones. Analysis of the turbulence kinetic energy (TKE) budget in this flow shows evidence of a strong production of TKE in the shear layer that forms as the flow is deflected around the block.     

Turbulent natural convection scaling in a vertical channel

Using direct numerical simulation (DNS) data, this study appraises existing scaling laws in literature for turbulent natural convection of air in a differentially heated vertical channel. The present data is validated using past DNS studies, and covers a range of Rayleigh number, Ra between 5.4 × 10⁵ and 2.0 × 10⁷. We then appraise and compare the various scaling laws proposed by Versteegh and Nieuwstadt, 1999, Hölling and Herwig, 2005, Shiri and George, 2008, George and Capp, 1979 with the profiles of the mean temperature defect, mean streamwise velocity, normal velocity fluctuations, temperature fluctuations and Reynolds shear stress. Based on the arguments of an inner (near-wall) and outer (channel centre) region, the data is found to support a minus one-third power law for the mean temperature in an overlap region. Using the inner and outer temperature profiles, an implicit heat transfer equation is obtained and we show that a correction term is non-negligible for the present Ra range when compared with explicit equations found in literature. In addition, we determined that the mean streamwise velocity and normal velocity fluctuations collapse in the inner region when using the outer velocity scale. We also find that the temperature fluctuations scale in inner coordinates, in contrast to the outer scaling behaviour reported in the past. Lastly, we show evidence of an incipient proportional relationship between friction velocity, u_τ, and the outer velocity scale, u_o, with increasing Ra.     

Drag reduction for liquid flow through micro-apertures

Pressure drops in the flow through micro-orifices and capillaries were measured for silicone oils, aqueous solutions of polyethylene glycol (PEG), and surfactant aqueous solutions. The diameter of micro-orifices ranged from 5 μm to 400 μm. The corresponding length/diameter ratio was from 4 to 0.05 and capillary diameters were 105 μm and 450 μm. The following results were obtained: silicone oils of 10^?6 m²/s and 10^?5 m²/s in kinematic viscosity generated a reduction of pressure drop (RPD), that is, drag reduction, similar to the RPD of water and a glycerol/water mixture reported in the previous paper by the present authors. When RPD occurred, the pressure drop (PD) of silicone oils of 10^?6 m²/s and 10^?5 m²/s had nearly the same magnitude. Namely, the difference in viscosity did not influence RPD. A 10³ ppm aqueous solution of PEG20000 provided almost the same PD as that of PEG8000 for the 400 μm to 15 μm orifices, but a greater PD than that of PEG8000 for the 10 μm to 5 μm orifices. A non-ionic surfactant and a cationic surfactant were highly effective in RPD compared with anionic surfactants: the non-ionic and cationic surfactant solutions had PD one order of magnitude lower than that of water under some flow conditions in the concentration range from 1 ppm to 10⁴ ppm, but the anionic surfactant solutions did not generate RPD except in the case of the smallest orifice of 5 μm in diameter. The PD of the non-ionic surfactant solution showed a steep rise at a Reynolds number (Re_t) for 400 μm to 15 μm orifices. The Re_t provides the relationship Re_t = K/D, where D is the orifice diameter, and K is a constant of 2 × 10^?2 m for the 100–20 μm orifices irrespective of liquid concentration. Capillary flow experiment revealed that the PEG, non-ionic and cationic surfactant solutions generated RPD also in a laminar flow through the capillary of 105 μm in diameter, but not in the flow through the capillary of 450 μm in diameter. In order to clarify the cause of RPD, an additional experiment was carried out by changing the orifice material from metal to acrylic resin. The result gave a different appearance of RPD, suggesting that RPD is related to an interfacial phenomenon between the liquid and wall. The large RPDs found in the present experiment are very interesting from both academic and practical viewpoints.