Flow boiling heat transfer study of R-134a/R-290/R-600a mixture in 9.52 and 12.7 mm smooth horizontal tubes: Experimental investigation

A detailed experimental investigation is carried out to study the flow boiling heat transfer behavior of R-134a/R-290/R-600a (91%/4.068%/4.932% by mass) refrigerant mixture in smooth horizontal tubes of diameter 9.52 and 12.7 mm. The heat transfer coefficients of the mixture are experimentally measured under varied heat flux conditions for stratified flow patterns using a coaxial counter-current heat exchanger test section. The tests are conducted for refrigerant inlet temperatures between ?9 and 5 °C and mass flow rates ranging from 3 to 5 g s^?1. Kattan–Thome–Favrat maps are used to confirm the flow patterns for the tested conditions. The magnitude of the heat transfer coefficient with respect to flow patterns and different mechanisms of boiling are discussed. The heat transfer coefficient of the refrigerant mixture is also compared with that of R-134a for selected working conditions. The significance of nucleate boiling in the overall heat transfer process under these testing conditions is highlighted.     

Thermohydraulics of turbulent flow through rectangular and square ducts with axial corrugation roughness and twisted-tapes with and without oblique teeth

The heat transfer and the pressure drop characteristics of turbulent flow of air (10,000 < Re < 100,000) through rectangular and square ducts with combined internal axial corrugations on all the surfaces of the ducts and with twisted-tape inserts with and without oblique teeth have been studied experimentally. The axial corrugations in combination with twisted-tapes of all types with oblique teeth have been found to perform better than those without oblique teeth in combination with axial corrugations. The heat transfer and the pressure drop measurements have been taken in separate test sections. Heat transfer tests were carried out in electrically heated stainless steel ducts incorporating uniform wall heat flux boundary conditions. Pressure drop tests were carried out in acrylic ducts. The flow friction and thermal characteristics are governed by duct aspect ratio, corrugation angle, corrugation pitch, twist ratio, space ratio, length, tooth horizontal length and tooth angle of the twisted-tape, Reynolds number and Prandtl number. Correlations developed for friction factor and Nusselt number have predicted the experimental data satisfactorily. The performance of the geometry under investigation has been evaluated. It has been found that on the basis of constant pumping power, up to 55% heat duty increase occurs for the combined axial corrugation and regularly spaced twisted-tape elements inserts with oblique teeth case compared to without oblique teeth twisted-tape inserts cases in the measured experimental parameters space. On the constant heat duty basis, the pumping power has been reduced up to 47% for the combined enhancement geometry than the individual enhancement geometries. However, full-length and short-length twisted-tapes with oblique teeth in combination with axial corrugations show only marginal improvements over the twisted-tapes without oblique teeth.     

Thermal and friction characteristics of laminar flow through rectangular and square ducts with transverse ribs and wire coil inserts

The heat transfer and the pressure drop characteristics of laminar flow of viscous oil (195 < Pr < 525) through rectangular and square ducts with internal transverse rib turbulators on two opposite surfaces of the ducts and with wire coil inserts have been studied experimentally. Circular duct has also been used. The transverse ribs in combination with wire coil inserts have been found to perform better than either ribs or wire coil inserts acting alone. The heat transfer and the pressure drop measurements have been taken in separate test sections. Heat transfer tests were carried out in electrically heated stainless steel ducts incorporating uniform wall heat flux boundary conditions. Pressure drop tests were carried out in acrylic ducts. The flow friction and thermal characteristics are governed by duct aspect ratio, coil helix angle and wire diameter of the coil, rib height and rib spacing, Reynolds number and Prandtl number. Correlations developed for friction factor and Nusselt number have predicted the experimental data satisfactorily. The performance of the geometry under investigation has been evaluated. It has been found that on the basis of constant pumping power, up to fifty per cent heat duty increase occurs for the combined ribs and wire coil inserts case compared to the individual ribs and wire coil inserts cases in the measured experimental parameters space. On the constant heat duty basis, the pumping power has been reduced up to forty per cent for the combined enhancement geometry than the individual enhancement geometries.     

Low-GWP refrigerants flow boiling heat transfer in a 5 PPI copper foam

This paper reports an experimental investigation of the heat transfer performance of the new low-GWP refrigerants, R1234yf and R1234ze(E), during flow boiling heat transfer inside a horizontal high porosity copper foam with 5 Pores Per Inch (PPI). Metal foams are a class of cellular structured materials consisting of a stochastic distribution of interconnected pores; these materials have been proposed as effective solutions for heat transfer enhancement during both single and two-phase heat transfer. R1234yf and R1234ze(E) refrigerants are appealing alternatives of the more traditional R134a by virtue of their negligible values of GWP and normal boiling temperatures close to that of R134a, which make them suitable solution in several different applications, such as: refrigeration and air conditioning and electronic thermal management. This work compares the two-phase heat transfer behaviour of these new HFO refrigerants, studying the boiling process inside a porous medium and permitting to understand their effective heat transfer capabilities. The experimental measurements were carried out by imposing three different heat fluxes: 50, 75, and 100 kW m⁻², at a constant saturation temperature of 30 °C; the refrigerant mass velocity was varied between 50 and 200 kg m⁻² s⁻¹, whilst the mean vapour quality varied from 0.2 to 0.95. The two-phase heat transfer and pressure drop performance of the two new HFO refrigerants is compared against that of the more traditional R134a.     

Flow pattern characterization for R-245fa in minichannels: Optical measurement technique and experimental results

An optical measurement method using image processing for two-phase flow pattern characterization in minichannel is developed. The bubble frequency, the percentage of small bubbles as well as their velocity are measured. A high-speed high-definition video camera is used to measure these parameters and to identify the flow regimes and their transitions. The tests are performed in a 3.0 mm glass channel using saturated R-245fa at 60 °C (4.6 bar). The mass velocity is ranging from 100 to 1500 kg/m² s, the heat flux is varying from 10 to 90 kW/m² and the inlet vapor quality from 0 to 1. Four flow patterns (bubbly flow, bubbly–slug flow, slug flow and annular flow) are recognized. The comparison between the present experimental intermittent/annular transition lines and five transition lines from macroscale and microscale flow pattern maps available in the literature is presented. Finally, the influence of the flow pattern on the heat transfer coefficient is highlighted.     

Heterogeneous nucleation on ultra smooth surfaces

An experimental investigation is presented with heterogeneous nucleate boiling on ultra smooth metallic surfaces (30-365 nm RMS roughness), including brass, unpolished stainless steel, and electropolished stainless steel. The fluids used for the investigation are highly wetting pentane and butane. It is observed that the incipient superheat is low for all cases considered, despite the fact that no vapor trapping cavities are available for incipience at low superheat. These data provide further evidence that in addition to vapor trapping, another mechanism must be available for heterogeneous nucleation in boiling systems. The boiling curves are presented for the different surface/fluid combinations. It is found that the heat transfer rate on the brass surface is considerably better than that on the stainless steel surfaces due to the ease with which nucleation sites are formed. In contrast, nucleation site formation on stainless steel is considerably more sparse than that on brass.     

Saturated nucleate boiling to binary and ternary mixtures on horizontal cylinder

In this investigation, a large number of experiments have been performed to determine saturated nucleate pool boiling heat transfer coefficients of MEA/water and DEA/water binary mixtures and that of water/MEA/DEA ternary mixtures. These heat transfer coefficients have been measured at atmospheric pressure and over a wide range of heat fluxes and solution concentrations. The heat flux has been varied in 14 different levels from 7 to about 230 kW/m² and amines concentration has been changed in 10 different levels from zero to 84 wt%. Results show that strong reduction of heat transfer coefficient occurs as a result of mass transfer interference in this phenomenon. Furthermore, in this study, all the correlations proposed during the last years for the prediction of nucleate boiling heat transfer coefficient of mixtures have been categorized in three groups. Some experimental results have been compared with the most accurate representatives of these three groups and the corresponding RMS errors have been calculated. Also, impacts of important existing parameters in these correlations like ideal heat transfer coefficient (h_id.) on the prediction have been discussed.     

Interfacial measurements in stratified types of flow. Part II: Measurements for R-22 and R-410A

A new optical void fraction measurement system has been coupled to a flow boiling test facility to obtain dynamic and time-averaged void fractions in a horizontal tube. A series of evaporation tests have been run for two refrigerants. R-22 was tested under mass velocity conditions of 70, 100, 150 and 200 kg/m² s and R-410A for 70, 150, 200 and 300 kg/m² s in a 13.6 mm diameter glass tube. Using our newly developed image processing system, about 227 000 images have been analyzed in this study to provide the same number of dynamic void fraction measurements. From these images, 238 time-averaged void fraction values have been obtained for vapor qualities from 0.01 to 0.95. These experimental points show very good agreement with the horizontal version of the Rouhani–Axelsson drift flux void fraction model.     

Influence of adverse pressure gradient on rough-wall turbulent flows

This paper presents an experimental investigation of adverse pressure gradient turbulent flow over two rough surfaces and a reference smooth surface. The adverse pressure gradient was produced in an asymmetric diffuser whose opening angle was 3°. The rough surfaces comprised sand grains and gravels of nominal mean diameters of 1.55 mm and 4.22 mm, respectively. The tests were conducted at an approach flow velocity of 0.5 m/s and the momentum thickness Reynolds number varied from 900 to 3000. A particle image velocimetry technique was used for the velocity measurements. Profiles of the mean velocity, turbulent intensities, Reynolds stress ratios, mixing length, eddy viscosity and the production terms were then obtained to document the effects of adverse pressure gradient (APG) on low Reynolds number rough-wall turbulent boundary layers. The results indicate that APG thickens the boundary layer and roughness sublayer. The APG and surface roughness also enhanced the production of turbulence as well as the turbulence level when compared with the smooth-wall data.     

Two-phase pressure drop and flow visualization of FC-72 in a silicon microchannel heat sink

The rapid development of two-phase microfluidic devices has triggered the demand for a detailed understanding of the flow characteristics inside microchannel heat sinks to advance the cooling process of micro-electronics. The present study focuses on the experimental investigation of pressure drop characteristics and flow visualization of a two-phase flow in a silicon microchannel heat sink. The microchannel heat sink consists of a rectangular silicon chip in which 45 rectangular microchannels were chemically etched with a depth of 276 μm, width of 225 μm, and a length of 16 mm. Experiments are carried out for mass fluxes ranging from 341 to 531 kg/m² s and heat fluxes from 60.4 to 130.6 kW/m² using FC-72 as the working fluid. Bubble growth and flow regimes are observed using high speed visualization. Three major flow regimes are identified: bubbly, slug, and annular. The frictional two-phase pressure drop increases with exit quality for a constant mass flux. An assessment of various pressure drop correlations reported in the literature is conducted for validation. A new general correlation is developed to predict the two-phase pressure drop in microchannel heat sinks for five different refrigerants. The experimental pressure drops for laminar-liquid laminar-vapor and laminar-liquid turbulent-vapor flow conditions are predicted by the new correlation with mean absolute errors of 10.4% and 14.5%, respectively.     

Experimental pool boiling investigations of FC-72 on silicon with artificial cavities and integrated temperature microsensors

In this experimental study, fluorinert FC-72 is boiled on a silicon chip with artificial cavities and integrated microsensors. The horizontal silicon chip with dimensions of 39.5 × 19 × 0.38 mm is completely immersed in FC-72. The integrated nickel–titanium temperature microsensors on the back of the chip are calibrated individually and exhibit a near-linear increase of electrical resistance with temperature. The applied heat fluxes and the resulting wall superheat at the boiling surface are varied by means of an integral thin-film resistance heater (95% Al, 4% Cu and 1% Si), also on the back of the silicon chip. Artificial cylindrical cavities with a mouth diameter of 10 μm and depths of 40, 80 or 100 μm situated above the microthermometers serve as artificial nucleation sites, due to trapped vapour. Bubble growth rates, frequencies, departure diameters of bubbles and waiting times between bubbles from an isolated cavity for different wall superheats and pressures were obtained by analysing high-speed video images and the simultaneously measured temperature below the artificial cavity.     

An experimental and numerical study of the localization behavior of tantalum and stainless steel

In general, the shear localization process involves initiation and growth. Initiation is expected to be a stochastic process in material space where anisotropy in the elastic–plastic behavior of single crystals and inter-crystalline interactions serve to form natural perturbations to the material’s local stability. A hat-shaped sample geometry was used to study shear localization growth. It is an axi-symmetric sample with an upper “hat” portion and a lower “brim” portion with the shear zone located between the hat and brim. The shear zone length is 870–890 μm with deformation imposed through a split-Hopkinson pressure bar system at maximum top-to-bottom velocity in the range of 8–25 m/s. We present experimental results of the deformation response of tantalum and 316L stainless steel samples. The tantalum samples did not form shear bands but the stainless steel sample formed a late stage shear band. We have also modeled these experiments using both conductive and adiabatic continuum models. An anisotropic elasto-viscoplastic constitutive model with damage evolution was used within the finite element code EPIC. A Mie-Gruneisen equation of state and the rate and temperature sensitive MTS flow stress model together with a Gurson flow surface were employed. The models performed well in predicting the experimental data. The numerical results for tantalum suggested a maximum equivalent strain rate on the order of 7 × 10⁴ s⁻¹ in the gage section for an imposed top surface displacement rate of 17.5 m/s. The models also suggested that for an initial temperature of 298 K a temperature in the neighborhood of 900 K was reached within the shear section. The numerical results for stainless steel suggest that melting temperature was reached throughout the shear band shortly after peak load. Due to sample geometry, the stress state in the shear zone was not pure shear; a significant normal stress relative to the shear zone basis line was developed.     

Evaporation heat transfer and flow characteristics of R-134a flowing through internally grooved tubes

This article describes experimental investigations of the heat transfer coefficient and pressure drop of R-134a flowing inside internally grooved tubes. The test tubes are one smooth tube and four grooved tubes. All test tubes are made from type 304 stainless steel, have an inner diameter of 7.1 mm, are 2,000 mm long and are installed horizontally. The test section is uniformly heated by a DC power supply to create evaporation conditions. The groove depth of all grooved tubes is fixed at 0.2 mm. The experimental conditions are conducted at saturation temperatures of 20, 25 and 30°C, heat fluxes of 5, 10 and 15 kW/m², and mass fluxes of 300, 500 and 700 kg/m² s. The effects of groove pitch, mass flux, heat flux, and saturation temperature on heat transfer coefficient and frictional pressure drop are discussed. The results illustrate that the grooved tubes have a significant effect on the heat transfer coefficient and frictional pressure drop augmentations.     

Circumferential temperature distribution during nucleate pool boiling outside smooth and modified horizontal tubes

In the work an approach to avoid a circumferential temperature distribution existing during nucleate pool boiling on a horizontal cylinder within low heat flux densities is presented. The idea of the approach is local heat transfer enhancement by a porous layer application on a part of the heating surface. An experiment on nucleate pool boiling heat transfer from horizontal cylinders to saturated R141b and water under atmospheric pressure is reported. Experiments have been conducted using stainless steel tubes with the outside diameter between 8 mm and 23 mm with the active length of 250 mm. The outside surface of the tubes was smooth or partially coated with a porous metallic layer. In particular, measurements of inside circumferential temperature distribution have been performed.     

Heat transfer and pressure drop studies in a circular tube fitted with straight full twist

Experimental investigation of heat transfer characteristics of circular tube fitted with straight full twist insert has been presented. The heat transfer coefficient increases with Reynolds number and decreasing spacer distance with maximum being 2 in. spacer distance for both the type of twist inserts. Also, there is no appreciable increase in heat transfer enhancement in straight full twist insert with 2 in. spacer distance. Experiments were carried out in turbulent flow using straight full twist insert with 4 in. spacer and similar trend of increasing Nusselt number with Reynolds number was observed. Performance evaluation analysis was made and the maximum performance ratio was obtained for each twist insert corresponding to the Reynolds number of 2550.     

Flow regime visualization and pressure drops of HFO-1234yf,R-134a and R-410A during downward two-phase flow in vertical return bends

This paper provides a qualitative visual observation of the two-phase flow patterns for HFO-1234yf and R-134a during downward flow in a vertical 6.7 mm inner diameter glass return bend. The different flow regimes observed are: slug, intermittent and annular flows. Bubble and vapor slug dynamical behaviors in downward slug flow are reported for HFO-1234yf. In addition, to determine the perturbation lengths up- and downstream of the return bend, the total pressure drop has been measured at different pressure tap location up- and downstream of the singularity. Furthermore, 285 pressure drop data points measured for two-phase flow of HFO-1234yf, R-134a and R-410A in vertical downward flow return bends are presented. The flow behavior in the return bend, which is subjected to the complex combined actions of gravity and centrifugal force was expressed in terms of the vapor Froude number. This experimental pressure drop database, which is included in the appendix, is compared to four well-known prediction methods available in the literature.     

Flow boiling heat transfer of R134a,R236fa and R245fa in a horizontal 1.030 mm circular channel

This research focuses on acquiring accurate flow boiling heat transfer data and flow pattern visualization for three refrigerants, R134a, R236fa and R245fa in a 1.030 mm channel. We investigate trends in the data, and their possible mechanisms, for mass fluxes from 200 to 1600 kg/m²s, heat fluxes from 2.3 kW/m² to 250 kW/m² at T_sat = 31 °C and ΔT_sub from 2 to 9 K. The local saturated flow boiling heat transfer coefficients display a heat flux and a mass flux dependency but no residual subcooling influence. The changes in heat transfer trends correspond well with flow regime transitions. These were segregated into the isolated bubble (IB) regime, the coalescing bubble (CB) regime, and the annular (A) regime for the three fluids. The importance of nucleate boiling and forced convection in these small channels is still relatively unclear and requires further research.     

An investigation of a model of the flow pattern transition mechanism in relation to the identification of annular flow of R134a in a vertical tube using various void fraction models and flow regime maps

In the present study, new experimental data are presented for literature on the prediction of film thickness and identification of flow regime during the co-current downward condensation in a vertical smooth copper tube having an inner diameter of 8.1 mm and a length of 500 mm. R134a and water are used as working fluids in the tube side and annular side of a double tube heat exchanger, respectively. Condensation experiments are done at mass fluxes of 300 and 515 kg m^?2 s^?1. The condensing temperatures are between 40 and 50 °C; heat fluxes are between 12.65 and 66.61 kW m^?2. The average experimental heat transfer coefficient of the refrigerant HFC-134a is calculated by applying an energy balance based on the energy transferred from the test section. A mathematical model by Barnea et al. based on the momentum balance of liquid and vapor phases is used to determine the condensation film thickness of R134a. The comparative film thickness values are determined indirectly using relevant measured data together with various void fraction models and correlations reported in the open literature. The effects of heat flux, mass flux, and condensation temperature on the film thickness and condensation heat transfer coefficient are also discussed for the laminar and turbulent flow conditions. There is a good agreement between the film thickness results obtained from the theoretical model and those obtained from six of 35 void fraction models in the high mass flux region of R134a. In spite of their different valid conditions, six well-known flow regime maps from the literature are found to be predictive for the annular flow conditions in the test tube in spite of their different operating conditions.     

Experimental and numerical investigation on air-side performance of fin-and-tube heat exchangers with various fin patterns

Air-side heat transfer and friction characteristics of five kinds of fin-and-tube heat exchangers, with the number of tube rows (N = 12) and the diameter of tubes (D_o = 18 mm), have been experimentally investigated. The test samples consist of five types of fin configurations: crimped spiral fin, plain fin, slit fin, fin with delta-wing longitudinal vortex generators (VGs) and mixed fin with front 6-row vortex-generator fin and rear 6-row slit fin. The heat transfer and friction factor correlations for different types of heat exchangers were obtained with the Reynolds numbers ranging from 4000 to 10000. It was found that crimped spiral fin provides higher heat transfer and pressure drop than the other four fins. The air-side performance of heat exchangers with the above five fins has been evaluated under three sets of criteria and it was shown that the heat exchanger with mixed fin (front vortex-generator fin and rear slit fin) has better performance than that with fin with delta-wing vortex generators, and the slit fin offers best heat transfer performance at high Reynolds numbers. Based on the correlations of numerical data, Genetic Algorithm optimization was carried out, and the optimization results indicated that the increase of VG attack angle or length, or decrease of VG height may enhance the performance of vortex-generator fin. The heat transfer performances for optimized vortex-generator fin and slit fin at hand have been compared with numerical method.     

Experimental study on steam chugging phenomenon in a vertical sparger

Unstable direct contact condensation called ``Chugging'' that occurs in certain conditions in the pressure suppression pool of Primary Containment Vessel of Boiling Water Reactors (BWRs) was studied experimentally. The mechanisms of every phase of the chugging was described, and experimental results useful for the development and validation of more accurate CFD models were provided. The experiment was conducted with a transparent pool and a transparent polycarbonate pipe or a stainless steel pipe with inner diameter of 27 mm under the conditions of the steam mass flux of 5.5–19.5 kg/m²s and the pool temperature of 19–46.5 °C. Pressure pulses were measured and synchronized with a high speed video camera for images acquisition. It was identified that the bubble implosion occurred while the pressure in the bubble quickly decreased. This condition might establish instability in the interfacial area which grew abruptly causing the implosion. Moreover the transparent apparatus allowed to interpret and relate internal condensations, generating pressure spikes of around 1.2 MPa because of the condensation-induced water hammer. Finally, the chugging condensation regime map was created from the experimental data.