Electrodeposition of Co–W coatings from boron gluconate electrolyte with a soluble tungsten anode

Conditions were determined in which an active anodic dissolution of tungsten is observed in a borongluconate electrolyte used to obtain Co–W coatings (pH ~6.5) and the nature of critical currents of transition to the passivation was found, which makes it possible to use the tungsten anode as a soluble electrode. The anodic dissolution of tungsten occurs under these conditions with a current efficiency of 90–100%, which, in contrast to the case of a graphite anode, does not lead to an additional oxidation of the electrolyte components and polymerization in solution; in combination with the decrease in the concentration of tungstate ions, this reduces the electrolyte performance. It was shown that the use of a soluble tungsten anode in obtaining nanocrystalline cobalt–tungsten coating can improve the electrolyte performance due to the rise in the current efficiency of electrodeposition and to the increase in the microhardness of the coatings in comparison with the case of an insoluble graphite anode.     

Activation and Photoinduced Release of Alkynes on a Biomimetic Tungsten Center: The Photochemical Behavior of the W−S-Phoz System

The synthesis and structural determination of four tungsten alkyne complexes coordinated by the bio-inspired S,N-donor ligand 2-(4′,4′-dimethyloxazoline-2′-yl)thiophenolate (S-Phoz) is presented. A previously established protocol that involved the reaction of the respective alkyne with the bis-carbonyl precursor [W(CO)₂(S-Phoz)₂] was used for the complexes [W(CO)(C₂R₂)(S-Phoz)₂] (R=H, 1 a ; Me, 1 b ; Ph, 1 c ). Oxidation with pyridine-N-oxide gave the corresponding W-oxo species [WO(C₂R₂)(S-Phoz)₂] (R=H, 2 a ; Me, 2 b ; Ph, 2 c ). All W-oxo-alkyne complexes ( 2 a , b , c ) were found to be capable of alkyne release upon light irradiation to afford five-coordinate [WO(S-Phoz)₂] ( 3 ). The photoinduced release of the alkyne ligand was studied in detail by in situ ¹H NMR measurements, which revealed correlation of the photodissociation rate constant ( 2 b>2 a>2 c ) with the elongation of the alkyne C≡C bond in the molecular structures. Oxidation of [WO(S-Phoz)₂] ( 3 ) with pyridine-N-oxide yielded [WO₂(S-Phoz)₂] ( 4 ), which shows highly fluxional behavior in solution. Variable-temperature ¹H NMR spectroscopy revealed three isomeric forms with respect to the ligand arrangement versus each other. Furthermore, compound 4 rearranges to tetranuclear oxo compound [W₄O₄(μ-O)₆(S-Phoz)₄] ( 5 ) and dinuclear [{WO(μ-O)(S-Phoz)}₂] ( 6 ) over time. The latter two were identified by single-crystal X-ray diffraction analyses.     

Synthesis,Structure and Photophysical Properties of a New Class of Inherently Chiral Boron(III) Chelates—The tert-Leucine Complexes

A new family of boron(III) chelates is introduced whereby molecular chirality, confirmed by circular dichroism, is imported during synthesis such that isolation of the diastereoisomers does not require separation procedures. The photophysical properties of two members of the family have been examined: the N,O,O-salicylaldehyde-based derivative shows pronounced intramolecular charge-transfer character in fluid solution and is weakly fluorescent, with a large Stokes shift. The corresponding 2-methylamino-benzaldehyde-derived N,N,O-chelate absorbs and fluoresces in the visible region with a much smaller Stokes shift. Orange fluorescence is also observed for this compound as a cast film. Temperature-dependence studies show that decay of the fluorescent state is weakly activated but emission is less than quantitative at 77 K. Quite rare for boron(III)-based chelates, this derivative undergoes intersystem crossing to form a meta-stable triplet-excited state. X-ray crystal structures are reported for both compounds, along with simulated ECD spectra.     

Reactions of a Silylyne Complex with Aldehydes: Formation of W−Si−O−C Four-Membered Metallacycles and Their Metathesis-Like Fragmentation

A tungsten silylyne complex having a W≡Si triple bond reacted with two molecules of aldehydes at room temperature to give W−Si−O−C four-membered metallacycles by [2+2] cycloaddition and subsequent formyl hydrogen transfer from one aldehyde molecule to another. Upon heating to 70 °C, the four-membered metallacycles underwent metathesis-like fragmentation cleanly to afford carbyne complexes and “silanoic esters,” in a manner similar to that of metallacyclobutadiene, an intermediate of alkyne metathesis reactions, and dimerization of the latter products gave 1,3-cyclodisiloxanes. The “silanoic ester” was also trapped by pivalaldehyde to give a [2+2] cycloaddition product in high yield.     

The “off-template” problem: synthesis and alkylation of a fused-butyrolactone from d-glucose

The synthesis of a fused-butyrolactone from D-glucose and its stereospecific alkylation in an off-template position is described, together with an unusual silyl protecting group migration.     

Impact of Intermolecular Non-Covalent Interactions in a CuI8PdII1 Discrete Assembly: Conformers’ Geometries and Stimuli-Sensitive Luminescence Properties

A new highly solid-state luminescent phase of a previously reported weakly luminescent Cu^I₈Pd^II₁ dicationic assembly is reported revealing the high geometrical versatility of this moiety that importantly alters its luminescent properties. This very minor new species B_c is based on a different conformer scaffold than the one encountered in the previously reported B_o form and, essentially differs from B_o by displaying shorter Cu^I-Cu^I intermetallic distances. DFT calculations allow concluding that the predominance in the solid-state of the weakly luminescent and less stable B_o phase is due to the extra stability induced by a larger number of intermolecular non-covalent π-CH interactions in its crystalline packing and not by the intrinsic stability of the Cu^I₈Pd^II₁ dicationic moiety. Calculations also revealed that a more stable conformation B_calc is expected in vacuum, which bears a different distribution of Cu^I-Cu^I intermetallic distances than the dications in B_o and B_c phases. Taking into account that the geometrical alterations are associated to drastic changes of luminescence properties, this confer to the Cu^I₈Pd^II₁ assembly high potentiality as stimuli-sensitive luminescent materials. Indeed, by applying mechanical or thermal stress to samples of B_o phase, new phases B_g and B_m , respectively, were obtained. Alterations of the solid-state photophysical properties of these new species compared to those recorded for B_o are reported together with a combined experimental and computed study of the structures/properties relationships observed in these phases.     

Carbonylation. 9. Alkoxycarbonylation of pent-3-ene nitrile with homogeneous Co−Ru catalysts: The respective roles of cobalt and ruthenium

Addition of ruthenium compounds (Ru(acac)₃, Ru₃(CO)₁₂) to cobalt catalysts for pent-3-ene nitrile alkoxycarbonylation increases both activity and selectivity in the production of cyanoesters by (i) reducing the amount of Co(II) and facilitating the generation of the active carbonylation species, HCo(CO)_n, and (ii) improving the isomerisation of pentene nitriles, providing significant amounts of pent-4-ene nitrile for the formation of the ω-ester.     

Isolation and Characterization of Naphthenic Acids from a Metal Naphthenate Deposit: Molecular Properties at Oil‐Water and Air‐Water Interfaces

Naphthenic acids from a West African metal naphthenate deposit have been isolated and characterized by infrared (IR), nuclear magnetic resonance (NMR), and Fourier transform ion cyclotron resonance mass spectrometry (FT‐ICR MS). The sample has been shown to comprise a narrow group of 4‐protic naphthenic acids of molecular weight ～1230 Da. The determined mass of 1230.0627 Da suggests a compound with the elemental composition C₈₀H₁₄₂O₈. The NMR data show no sign of carbon‐carbon multiple bonds. Hence, the elemental composition indicates the presence of six saturated hydrocarbon rings. The naphthenic acids have proved to be highly oil‐water (o/w) interfacially active. On elevation of the pH from 5.6 to 9.0, interfacial activity increases gradually due to a higher degree of dissociation of the carboxylic groups. At pH 9.0, the interfacial tension (IFT) between water and toluene‐hexadecane (1–9 vol.) is lowered by ～40 mN/m at concentrations of only 0.0050–0.010 mM naphthenic acid. The time rate of decrease of the IFT (dγ/dt) is also concentration‐dependent, and a well‐defined IFT is attained at long observation periods.

The C₈₀ naphthenic acids form relatively unstable Langmuir monolayers. The stability decreases further with increasing pH as more monomers become dissociated and dissolve into the aqueous phase. The stability is altered upon addition of calcium ions into the subphase due to formation of calcium naphthenate at the surface. In the undissociated state, the acids have a molecular area of ～160 Å²/molecule in the noninteracting region. The high area reflects an extended molecular structure comprising four carboxylic head groups, which are likely to be separated by hydrocarbon chains.     

Synthesis,crystal structures and magnetic properties of a series of new cyano-bridged complexes derived from templates [Ni(CN)4]2− and [Co(III)(CN)6]3−

Three new cyano-bridged complexes 1 [Ni(tn)₂Ni(CN)₄] (tn?=?1,3-diaminopropane), 2 [Cu^II(dipn)Ni^II(CN)₄], and 3 [Cu(dipn)]₆[Co(CN)₆]₄?·?4H₂O (dipn?=?dipropylenetriamine) have been assembled by the templates [Ni(CN)₄]^2? and [Co(CN)₆]^3?. 1 consists of a one-dimensional linear chain–Ni(tn)₂–NC–Ni(CN)₂–CN–Ni(tn)_2? in which the Ni(II) centers are linked by two CN groups. One 1-D zigzag chain of 2 is formed with–Ni(2)–C–N–Cu(1)–N–C–linkages. A 2D structure of 3 is formed by an alternate array of [Co(CN)₆]^3? and [Co][Cu₆] units. For 1, there is an overall weak antiferromagnetic interaction between Ni(II) ions through the–NC–Ni–CN–bridges of the diamagnetic [Ni(CN)₄]^2? anions. 2 exhibits a weak antiferromagnetic exchange interaction between copper(II) ions mediated by [Ni(CN)₄]^2? diamagnetic bridges. Complex 3 exhibits a weak ferromagnetic interaction between nearest Cu^II and Cu^II atoms through–NC–Co–CN–bridges.     

Preparation of trans Diequatorial 2,3-Pyruvate Acetals in a Di- and a Trisaccharide Related to the K-Antigen from E. Coli 0101:K103:H−

Abstract

Using methyl 2,2-bis(ethylthio)propionate as acetalating agent and triflic acid-sulfuryl chloride as catalyst, synthesis of 2,3-trans diequatorial pyruvate ketal was achieved. Starting from D-galactose and L-rhamnose derivatives, methyl 2,3,4,6-tetra-O-benzyl-α-D-galactopyranosyl-(1→4)-6-O-benzyl-2,3-O-(1-methoxycarbonyl)ethylidene- α-D-galactopyranosyl-(1→3)-2,4-di-O-benzyl-α-L-rhamnopyranoside and methyl 4,6-di-O-benzyl-2,3-O-(1-methoxy-carbonyl)ethylidene-α-D-galactopyranosyl-(1→3)-2,4-di-O-benzyl-α-L-rhamnopyranoside were synthesized. Removal of the protecting groups from the former, afforded the trisaccharide repeating unit of the K-antigen from E.coli O101:K103:H^? in the form of its methyl glycoside methyl ester.     

Endohedral Plumbaspherenes of the Group 9 Metals: Synthesis,Structure and Properties of the [M@Pb12]3− (M=Co,Rh, Ir) Ions

The icosahedral [M@Pb₁₂]³⁻ (M=Co( 1 ), Rh( 2 ), Ir( 3 )) cluster ions were prepared from K₄Pb₉ and Co(dppe)Cl₂ (dppe=1,2-bis(diphenylphosphino)ethane)/[Rh(PPh₃)₃Cl]/[Ir(cod)Cl]₂ (cod=1,5-cyclooctadiene), respectively, in the presence of 18-crown-6/ 2,2,2-cryptand in ethylenediamine/toluene solvent mixtures. The [K(2,2,2-cryptand)]⁺ salt of 1 and the [K(18-crown-6)]⁺ salt of 3 were characterized via X-ray crystallography; the ions 1 and 3 are isostructural and isoelectronic to the [Rh@Pb₁₂]³⁻ ( 2 ) ion as well as to the group 10 clusters [M′@Pb₁₂]²⁻ (M′=Ni, Pd, Pt). The ions are all 26-electron clusters with near perfect icosahedral I_h point symmetry. Clusters 1 – 3 show record downfield ²⁰⁷Pb NMR chemical shifts due to σ-aromaticity of the cluster framework. Calculated and observed ²⁰⁷Pb NMR chemical shifts and ²⁰⁷Pb–^xM J-couplings (^xM=⁵⁹Co, ¹⁰³Rh, ¹⁹³Ir) are in excellent agreement and DFT analysis shows that the variations of ²⁰⁷Pb NMR chemical shifts for the [M@Pb₁₂]^{2, 3−} ions (M=Co, Rh, Ir, Ni, Pd, Pt) are mainly governed by the perpendicularly oriented σ₁₁ component of the chemical shift anisotropy tensor. The laser desorption ionization time-of-flight (LDI-TOF) mass spectra contain the molecular ions as well as several new gas phase clusters derived from the parents. The DFT-minimized structures of these ions are described.     

Electrodeposition of Zn–Ni–P compositionally modulated multilayer coatings: An attempt to deposit Ni–P and Zn–Ni alloys from a single bath

The effects of bath composition and deposition variables on the electrodeposition of Zn–Ni–P alloys were studied in order to develop a single bath for deposition of Ni–P/Zn–Ni compositionally modulated multilayer coatings (CMMCs). The basis for development of the bath was a large increase in the Ni deposition rate compared to that of Zn at low deposition overpotentials combined with the impossibility of codeposition of Zn with P. EDS analysis demonstrated that the deposits obtained from the Zn–Ni–P bath at low overpotentials were practically all Ni–P, while the alloy deposited at high overpotentials was mainly Zn–Ni with around 3.2 wt% P content.     

Reductive Coupling of (Fluoro)pyridines by Linear 3d-Metal(I) Silylamides of Cr–Co: A Tale of C−C Bond Formation,C−F Bond Cleavage and a Pyridyl Radical Anion

Herein, we disclose the facile reduction of pyridine (and its derivatives) by linear 3d-metal(I) silylamides (M=Cr–Co). This reaction resulted in intermolecular C−C coupling to give dinuclear metal(II) complexes bearing a bridging 4,4′-dihydrobipyridyl ligand. For iron, we demonstrated that the C−C coupling is reversible in solution, either directly or by reaction with substrates, via a presumed monomeric metal(II) complex bearing a pyridyl radical anion. In the course of this investigation, we also observed that the dinuclear metal(II) complex incorporating iron facilitated the isomerisation of 1,4-cyclohexadiene to 1,3-cyclohexadiene as well as equimolar amounts of benzene and cyclohexene. Furthermore, we synthesised and structurally characterised a non-3d-metal-bound pyridyl radical anion. The reactions of the silylamides with perfluoropyridine led to C−F bond cleavage with the formation of metal(II) fluoride complexes of manganese, iron and cobalt along with the homocoupling or reductive degradation of the substrate. In the case of cobalt, the use of lesser fluorinated pyridines led to C−F bond cleavage but no homocoupling. Overall, in this paper we provide insights into the multifaceted behaviour of simple (fluoro)pyridines in the presence of moderately to highly reducing metal complexes.     

Electronic Structures, (d-p)π Conjugation Effects, and Spectroscopic Properties of Polyoxometalates: M6O19 2− (M=Cr, Mo, W)

The electronic structures and bonding of isopoly oxometalates M₆O₁₉ ^2– (M=Cr, Mo, W) have been investigated by using ab initio and relativistic density functional methods. We have discussed the role of the central oxygen atom and the (d-p) conjugation interactions between the metal and bridging oxygen atoms. It is found that there exist 12 three-centered two-electron (d-p-d) bonds for the three M₄(-O)₄ planar rings in M₆O₁₉ ^2– ions and these hexametalates are considered to have quasi-aromaticity. The (d-p) conjugation effects play essential role in stabilizing these cluster compounds, and the reduced (d-p) conjugation effects account for the instability of the isopoly oxochromate ion, Cr₆O₁₉ ^2–. The vibrational spectra and electronic spectra of M₆O₁₉ ^2– ions are evaluated and assigned theoretically and the calculated spectra are in fairly good agreement with the measured experimental results.     

Synthesis and physical studies on a new anion exchange material: Zirconium (IV) ethylenediamine and its application to the separation of MoO42− from other anionic species

Zirconium (IV) ethylenediamine has been prepared by interaction of aqueous solutions of zirconium oxychloride and ehtylenediamine at pH 4.4 and 9.6. Its anion exchange capacity, chemical and thermal stabilities, pH titration curve and chemical composition were studied. Infrared spectra using the KBr disc method, TGA and DTA were recorded. A tentative formula was proposed showing zirconium (IV) oxide : ethylenediamine in the ratio 3:1, [ZrO(OH)⁺²]₃ [NH₂ (CH₂) ₂NH₂]. 3 H₂O. Distribution coefficient (Kd) values of a number of anionic species were determined in distilled water, and various concentrations of ammonium nitrate solution. On the basis of the difference in Kd values, the separations such as Cl⁻ - MoO₄²⁻, Br - MoO₄²⁻, I⁻ - MoO₄²⁻, SO₄²⁻ - MoO₄²⁻ and C₂O₄²⁻ - MoO₄²⁻ have been achieved successfully on its column.     

Synthesis,Crystal Structure and Properties of a Chiral 3D Supramolecular Coordination Polymer [Co(HL)·(DMF)]_n from 5-(Imidazol-1-ylmethyl)isophthalic Acid

A chiral supramolecular coordination polymer, [Co(HL)·(DMF)]n(1), with helical chains from a flexible ligand 5-(imidazol-1-ylmethyl)isophthalic acid(H2L) has been obtained under hydrothermal conditions and characterized by elemental analysis, powder X-ray diffraction(PXRD), IR, Uv/vis spectra, thermal gravimetric analyses(TGA) and also by single-crystal X-ray diffraction. It crystallizes in hexagonal, space group P6522 with a = 8.8109(3), b = 8.8109(3), c = 71.771(3) ?, γ = 120°, V = 4825.3(3) ?~3, Z = 6, M_r = 695.55, D_c = 1.436 g/cm~3, Rint = 0.0684, F(000) = 2166, the final R = 0.0923 and w R = 0.2697 for 3056 observed reflections(I 2σ(I)). The title coordination polymer 1 shows a chiral layered structure based on right-handed helix chains. Such layers are associated together through hydrogen-bonding interactions to form a 3D supramolecular framework.     

Mechanical Properties of Dense Zeolitic Imidazolate Frameworks (ZIFs): A High‐Pressure X‐ray Diffraction,Nanoindentation and Computational Study of the Zinc Framework Zn(Im)2, and its Lithium?Boron Analogue,LiB(Im)4

The dense, anhydrous zeolitic imidazolate frameworks (ZIFs), Zn(Im)₂ ( 1 ) and LiB(Im)₄ ( 2 ), adopt the same zni topology and differ only in terms of the inorganic species present in their structures. Their mechanical properties (specifically the Young’s and bulk moduli, along with the hardness) have been elucidated by using high pressure, synchrotron X‐ray diffraction, density functional calculations and nanoindentation studies. Under hydrostatic pressure, framework 2 undergoes a phase transition at 1.69 GPa, which is somewhat higher than the transition previously reported in 1 . The Young’s modulus (E) and hardness (H) of 1 (E≈8.5, H≈1 GPa) is substantially higher than that of 2 (E≈3, H≈0.1 GPa), whilst its bulk modulus is relatively lower (≈14 GPa cf. ≈16.6 GPa). The heavier, zinc‐containing material was also found to be significantly harder than its light analogue. The differential behaviour of the two materials is discussed in terms of the smaller pore volume of 2 and the greater flexibility of the LiN₄ tetrathedron compared with the ZnN₄ and BN₄ units.     

The Acetoxyfulvene Synthesis of Prostaglandins: A New,Versatile Synthesis of dl-PGF1δ, dl-PGF2α, dl-PGE1 and dl-PGE2 from a Common Intermediate

Abstract

In the Corey¹ synthesis of prostaglandins and in our recently published modifications^2,3 a synthon containing carbon atoms 14 to 20^θ is first added to a bicyclic intermediate (C-6 to C-13) and completion of the prostaglandin skeleton by addition of a second synthon containing carbon atoms 1 to 5 forms a subsequent step. In a modification^4,5 of the Corey synthesis¹ PGF_1α and PGE₁ were made by reversing the order in which these two synthons were added to the cyclopentane ring (C-6 to C-13). The major limitation of this modified route^4,5 is that it is restricted to the preparation of prostaglandins of the 1-series,^? because hydrogenolysis of the benzyl group of the intermediate ester (1) reduces the C-5, C-6 double bond to form the saturated alcohol (2), which cannot be converted into prostaglandins of the 2-series^?.     

The chemistry of localized singlet 1,3-diradicals (biradicals): from putative intermediates to persistent species and unusual molecules with a π-single bonded character

Localized singlet diradicals (biradicals) are key intermediates in chemical reactions involving homolytic bond-cleavage and formation processes. The molecular structure and electronic structure had been historically elusive due to the short-lived character of the reactive intermediates. In the last 15 years, a significant development of singlet diradical chemistry was achieved after the pioneering findings of long-lived singlet diradicals. In this tutorial review, the recent development of localized singlet diradical chemistry is summarized and discussed. The following subjects are included (a) the mechanism by which the ground state spin-multiplicity of localized 1,3-diradicals is controlled; (b) the substituent and heteroatom effect on the most stable electronic configuration of the singlet 1,3-diradicals, type-1 versus type-2; (c) the molecular design for the long-lived singlet ground state diradicals; (d) the generation and characterization of the singlet diradicals; and (e) the future prospects.     

The atomic structural dynamics of γ-Al2O3 supported Ir-Pt nanocluster catalysts prepared from a bimetallic molecular precursor: a study using aberration-corrected electron microscopy and X-ray absorption spectroscopy

This study describes a prototypical, bimetallic heterogeneous catalyst: compositionally well-defined Ir-Pt nanoclusters with sizes in the range of 1-2 nm supported on γ-Al(2)O(3). Deposition of the molecular bimetallic cluster [Ir(3)Pt(3)(μ-CO)(3)(CO)(3)(η-C(5)Me(5))(3)] on γ-Al(2)O(3), and its subsequent reduction with hydrogen, provides highly dispersed supported bimetallic Ir-Pt nanoparticles. Using spherical aberration-corrected scanning transmission electron microscopy (C(s)-STEM) and theoretical modeling of synchrotron-based X-ray absorption spectroscopy (XAS) measurements, our studies provide unambiguous structural assignments for this model catalytic system. The atomic resolution C(s)-STEM images reveal strong and specific lattice-directed strains in the clusters that follow local bonding configurations of the γ-Al(2)O(3) support. Combined nanobeam diffraction (NBD) and high-resolution transmission electron microscopy (HRTEM) data suggest the polycrystalline γ-Al(2)O(3) support material predominantly exposes (001) and (011) surface planes (ones commensurate with the zone axis orientations frequently exhibited by the bimetallic clusters). The data reveal that the supported bimetallic clusters exhibit complex patterns of structural dynamics, ones evidencing perturbations of an underlying oblate/hemispherical cuboctahedral cluster-core geometry with cores that are enriched in Ir (a result consistent with models based on surface energetics, which favor an ambient cluster termination by Pt) due to the dynamical responses of the M-M bonding to the specifics of the adsorbate and metal-support interactions. Taken together, the data demonstrate that strong temperature-dependent charge-transfer effects occur that are likely mediated variably by the cluster-support, cluster-adsorbate, and intermetallic bonding interactions.