再生纤维素／聚乙烯醇共混膜的研究

由纤维素铜氨溶液与不同体积比（１－１０％）的聚乙烯醇（ＰＶＡ）水溶液共混制备了一系列再生纤维素共混膜．扫描电镜结果表明ＰＶＡ含量大于８％时，该共混膜产生明显相分离．当ＰＶＡ低于５％时，共混膜相容性较好．膜的结晶度，抗张强度，直角撕裂强度，断裂伸长及耐热性均优于单独用钢氨液制备的再生纤维素膜．此外，用流动速率法和超滤法测定了膜的孔径，渗透性及纯水通量，结果表明共混膜的孔性没有明显变化．本文得出：再生纤维素与５％ＰＶＡ共混能改善力学性能，并且能保持其生物降解性．     

Design and fabrication of electrospun polyethersulfone nanofibrous scaffold for high‐flux nanofiltration membranes

A novel class of high‐flux and low‐fouling thin‐film nanofibrous composite (TFNC) membranes, containing a thin hydrophilic top‐layer coating, a nanofibrous mid‐layer scaffold and a non‐woven microfibrous support, has been demonstrated for nanofiltration (NF) applications. In this study, the issues related to the design and fabrication of a polyethersulfone (PES) electrospun nanofibrous scaffold for TFNC NF membranes were investigated. These issues included the influence of solvent mixture ratio, solute concentration, additives, relative humidity (RH), and solution flow rate on the morphology of an electrospun PES nanofibrous scaffold, the distribution of fiber diameter, the adhesion between the PES scaffold and a typical poly(ethylene terephthalate) (PET) non‐woven support, as well as the tensile properties of the nanofibrous PES/non‐woven PET composite substrates. Uniform and thin nanofibrous PES scaffolds with strong adhesion to the nanofiber‐PET non‐woven are several of the key parameters to optimize the NF performance of TFNC membranes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2288–2300, 2009     

Nanoscale Distribution of Sulfonic Acid Groups Determines Structure and Binding of Water in Nafion Membranes

The connection between the nanoscale structure of two chemically equivalent, yet morphologically distinct Nafion fuel‐cell membranes and their macroscopic chemical properties is demonstrated. Quantification of the chemical interactions between water and Nafion reveals that extruded membranes have smaller water channels with a reduced sulfonic acid head group density compared to dispersion‐cast membranes. As a result, a disproportionally large amount of non‐bulk water molecules exists in extruded membranes, which also exhibit larger proton conductivity and larger water mobility compared to cast membranes. The differences in the physicochemical properties of the membranes, that is, the chemical constitution of the water channels and the local water structure, and the accompanying differences in macroscopic water and proton transport suggest that the chemistry of nanoscale channels is an important, yet largely overlooked parameter that influences the functionality of fuel‐cell membranes.     

Side chain crosslinking of aromatic polyethers for high temperature polymer electrolyte membrane fuel cell applications

Novel aromatic polymers bearing polar pyridine units in the main chain and side chain crosslinkable hydroxyl and propargyl groups have been successfully synthesized. The polymers have been investigated in terms of their critical properties related to their application in high temperature polymer electrolyte membrane fuel cells, such as doping ability, mechanical properties, and thermal stability. Crosslinked membranes were prepared by direct crosslinking of hydroxyl side chain groups with decafluorobiphenyl used for the first time as a crosslinking agent. However, further functionalization of hydroxyl groups to the propargyl derivative has also led to crosslinked polymers after thermal curing. Both types of crosslinked membranes exhibited higher glass transition temperatures as well as lower doping levels when doped in phosphoric acid compared with the non crosslinked analogs, confirming the formation of a successfully crosslinked network. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Development of Poor Cell Adhesive Immersion Precipitation Membranes Based on Supramolecular Bis‐Urea Polymers

A variety of biomedical applications requires tailored membranes; fabrication through a mix‐and‐match approach is simple and desired. Polymers based on supramolecular bis‐urea (BU) moieties are capable of modular integration through directed non‐covalent stacking. Here, it is proposed that non‐cell adhesive properties can be introduced in polycaprolactone‐BU‐based membranes by the addition of poly(ethylene glycol) (PEG)‐BU during immersion precipitation membrane fabrication, while unmodified PEG is not retained in the membrane. PEG‐BU addition results in denser membranes with a similar pore size compared to pristine membranes, while PEG addition induces defect formation. Infrared spectroscopy and surface hydrophobicity measurements indicate that PEG‐BU is retained during membrane processing. Additionally, PEG‐BU incorporation successfully leads to poor cell adhesive surfaces. No evidence is observed to indicate PEG retention. The results obtained indicate that the BU system enables intimate mixing of BU‐modified polymers after processing. Collectively, the results provide the first steps toward BU‐based immersion precipitated supramolecular membranes for biomedical applications.     

Solvent‐free fabrication of proton‐conducting membranes based on commercial elastomers

Five different types of elastomers were examined as the matrix materials in the preparation of non‐fluorinated proton exchange membranes utilizing a solvent‐free route via the in situ reaction of sodium 4‐styrenesulfonate (NaSS). The morphology of the elastomer/NaSS vulcanizates was studied to evaluate the effect of polarity, viscosity and saturation degree of the elastomer matrixes. Much better dispersion of NaSS was found in chlorosulfonated polyethylene rubber (CSM) and hydrogenated nitrile butadiene rubber (HNBR) matrixes than in the other three types of elastomer matrixes. For CSM/NaSS and HNBR/NaSS proton exchange membranes, distinctive membrane properties were observed and correlated with their different structure and morphologies. The CSM/NaSS membranes exhibited the proton conductivity as high as ~0.03 S cm^?1 and the selectivity (the ratio of proton conductivity to methanol permeability) higher than that of Nafion. Copyright © 2015 John Wiley & Sons, Ltd.     

Novel nanocomposite membranes from cellulose acetate and clay‐silica nanowires

In this study, a new class of heterogeneous membranes based on cellulose acetate (CA) polymer and a complex filler clay‐silica nanowires (SiO₂NWs) was investigated for potential biomedical applications. SiO₂NWs were synthesized using natural clay through a facile sol–gel method and were dispersed in the polymer solution by sonication in the 1.25, 2.5, and 5% weight ratio to the CA acetate polymer. Membranes were subsequently prepared via phase inversion by precipitation of the CA polymer in water. The pristine CA membrane and SiO₂NWs based nanocomposites membranes were characterized using different characterization techniques. The presence of the SiO₂NWs in the CA membrane was found to significantly enhance the protein retention, water wettability and thermal as well as mechanical properties in comparison to the pristine CA membrane. Water flows studies at different temperatures and the retention of bovine serum albumin have been studied and the nanocomposite membranes were found to exhibit superior performances compared with the pristine CA membranes. SiO₂NWs‐CA membranes showed a much higher stability to the water temperature change during separation than CA membranes. Morphological changes clearly revealed that the composite membrane were much more compact than the pristine CA membranes. The rabbit dermal fibroblasts cell viability in cultures after 72 hr of incubation was found to be greater than 80%. These newly synthesized composite membranes exhibit a high potential to be used for various medical applications because of their non‐cytotoxic characteristics. Copyright © 2016 John Wiley & Sons, Ltd.     

Microporous polyethersulfone membranes prepared under the combined precipitation conditions with non‐solvent additives

Using diethylene glycol (DegOH) as non‐solvent additive (NSA) and N, N‐dimethylacetamide (DMAc) as solvent (S), polyethersulfone (PES) flat sheet membranes were prepared via immersion precipitation combined with the vapor induced phase separation (VIPS) process. Light transmittance was used to follow the precipitation rate during the immersion process as well as during the VIPS stage. As the addition of the NSA, the viscosity of casting solutions increased, which led to a slow precipitation rate. Though the precipitation rate decreased, the instantaneous demixing type was maintained. High flux membranes were obtained only at a high mass ratio of NSA/S; producing membranes had cellular pores on the top surface and sponge‐like structure on cross section. The VIPS process prior to immersion precipitation was important for the formation of cellular pore on the surface. With the increase in exposure time, the liquid–liquid phase separation took place on the surface of casting solution; nucleation and growth induced the formation of cellular pore on the top surface. Coagulation bath temperature also had large effect on the precipitation rate; high temperature on coagulation bath mainly accelerated the transfer of solvent and non‐solvent. Higher flux membrane with a porous skin layer could be obtained at a high coagulation bath temperature, but at the same time the mechanism properties were weakened. Copyright © 2007 John Wiley & Sons, Ltd.     

Chemical and biology aging of novel green membranes made of PVA and wood flour fibers reinforced with nanosilica manufactured by compression molding process

The purpose of this work was to improve the biodegradable properties of polyvinyl alcohol (PVA)/nanowood flour membranes consisting of nanosilica which were manufactured by compression molding process. Cross-linking of PVA was used to improve the mechanical properties and prevent high solubility of the obtained transient membranes. Plasticizer used to increase the plasticity of transient membranes. The biodegradability of transient membranes was evaluated under UV accelerated weathering as well as soil burial test. The transient membranes were characterized by Fourier transform infrared spectra and X-ray diffraction to study the chemical structure. Mechanical strength was appointed to characterize and reveal the mechanical, thermal analysis and the structural properties of such transient membranes. Scanning electron microscope was used to characterize the morphology of transient membranes. Swelling test and weight loss due to biodegradation were also evaluated. The results showed that the developed transient membranes can be used as food packaging bags due to biodegradability (weight loss) under irradiation and during burial soil which making them environmentally friendly.     

聚全氟乙丙烯中空纤维膜研究

以聚全氟乙丙烯(FEP)为成膜聚合物,复合无机粒子为成孔剂,邻苯二甲酸二辛酯(DOP)为稀释剂,采用熔融纺丝工艺制备得到FEP中空纤维膜.分析和讨论了不同成膜体系对FEP中空纤维膜热性能、动态力学性能和力学性能的影响,并对膜的纯水通量和孔径分布进行表征.用扫描电子显微镜(SEM)观察了膜的横断面和表面形貌.结果表明,所得FEP中空纤维膜为由溶出微孔和界面微孔组成的海绵状孔结构.随着成孔剂含量的增加,成孔剂在成膜体系中分散程度变差,容易发生团聚,最终导致膜孔径变大,孔径分布变宽.成孔剂和稀释剂对FEP中空纤维膜的热性能和动态力学性能影响较小.当FEP含量增加到70 wt％时,膜表面容易形成一层致密层,降低了膜的通透性.     

Preparation and properties of A-B-A tri-block copolymer membranes consisting of N-hydroxypropyl-l-glutamine as the A component and l-alanine as the B component

A-B-A type tri-block copolymer consisting of N-hydroxypropyl-l-glutamine as the A component and l-alanine as the B component as well as the corresponding random copolymers and homopolymers were prepared by carrying out an aminoalcoholysis reaction with 3-amino-1-propanol, together with a crosslinking reaction with 1,8-octamethylenediamine on membranes of the starting polymer membranes including γ-methyl-l-glutamate residue. It was shown that the effective crosslink density was proportional to the percent crosslinker in the reaction mixture. The relation between their bulk structure and membrane properties were investigated, such as the swelling ratio in water (q), tensile properties, and enzymatic degradation behavior of the membranes in a pseudo-extracellular fluid (PECF). The tensile properties of the hydrophilic membranes were highly dependent on q in PECF, and on the hydrophobic portions in molecular chains, whose behavior was typical of an elastomer. Biodegradation of the membranes in vitro by bromelain indicated that the degradation took place in bulk rather than on the surface, and that the rate of degradation was also highly dependent on q in the samples as well as on the hydrophobic portion of the membranes in PECF.     

Preparation and characterization of asymmetric polyethersulfone (PES) membranes

Flat‐sheet asymmetric polyethersulfone (PES) membranes were prepared from polyethersulfone (PES)/ polyethylene glycol (PEG)/ N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion induced by immersion precipitation in water coagulation bath. Effects of propionic acid (PA) as a non‐solvent additive (NSA) on morphology and performance of the membranes prepared from PES/PEG 6000/NMP system in water coagulation bath were investigated. The cross section morphology of the membranes was studied by scanning electron microscopy (SEM). In addition, performance of the membranes was studied by water content measurements and separation experiments using pure water and human serum albumin (HSA) protein solution as feeds. According to SEM analysis, it was found out that the NSA has a significant influence on the structure of the skin layer and the sublayer. The obtained results indicated that addition of PA to the casting solution decreases permeation flux of the prepared membranes. Copyright © 2009 John Wiley & Sons, Ltd.     

DABCO‐functionalized polysulfones as anion‐exchange membranes for fuel cell applications: Effect of crosslinking

A series of DABCO‐functionalized polysulfones were synthesized and characterized. The effect that crosslinking has on the membrane properties containing different degrees of functionalization was evaluated. These polymers showed good thermal stability below the fuel cell operation temperature, T < 100 °C, reflected by the T_OD, T_FD, and thermal durability. The water uptake increased as the percentage of DABCO groups increased and the crosslinked membranes showed lower capacity to absorb water than the non‐crosslinked ones favoring thus the dimensional stability of the first ones. Membranes in the chloride form containing low degree of functionalization exhibited the highest tensile strength values. The ionic conductivity of non‐crosslinked membranes varied as a function of the functionalization degree until a value of around 100% achieving a maximum value at 86%. However, the crosslinked ones showed satisfactory ionic conductivities for values higher than 100%. The behavior of these polymeric materials in alkaline solutions revealed a great alkaline stability necessary to be used as solid electrolytes in fuel cells. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1326–1336     

Development of urethane acrylate composite ion-exchange membranes and their electrochemical characterization

With the objective of introducing antifouling characteristics into interpolymer types of cation and anion exchange membranes, the surface of these membranes was coated with a 12-microm-thick urethane acrylate layer and was cured by UV radiation of wavelengths 308 and 172 nm under a complete inert atmosphere. Different urethane acrylate composite ion exchange membranes developed were characterized in NaCl solution by measuring their ion-exchange capacity, volume fraction of water, contact angle with water, membrane conductance, and membrane potential. It was found that the electrochemical transport properties of urethane acrylate composite cation-exchange membranes were increased due to resonance stabilization of the urethane group, which acts as a weak acid and dissociates as a negatively charged urethane ion and a positively charged proton. This contributes toward the net charge density of the membrane matrix responsible for enhanced selectivity and conductivity, while for urethane acrylate composite anion-exchange membranes reduction in net charge density was responsible for reduction in electrochemical transport properties. Counterion transport number, permselectivity, and counterion diffusion coefficient values for these membranes were also estimated. Experiments were also carried out in higher homologs of sodium carboxylate solutions in order to observe the fouling tendencies of these membranes. It was concluded that it is possible to obtain antifouling characteristics of ion-exchange membranes by coating and curing thin hydrophilic layers of urethane acrylate on their surfaces without sacrificing their electrochemical transport properties.     

Selective separation of magnolol using molecularly imprinted membranes

Molecularly imprinted membranes (MIMs) for selective separation of magnolol were prepared by thermal polymerization using magnolol as the template, ethylene glycol dimethacrylate (EGDMA) as the cross‐linker, 2,2‐azobisisobutyronitrile (AIBN) as the initiator, organic solvent as the porogen, methacrylamide (MAM) and acrylic acid (AA) as the functional monomers and cellulose acetate as the agglutinant. Commercial filter paper was used as the supporting material. The effects of different porogens and the ratio of functional monomers on the binding and recognition capacity of MIMs were investigated, and the morphology of the membranes was examined by scanning electron microscopy (SEM). The results showed that the MIMs have the highest selectivity to magnolol when the ratio of MAM/AA was 1:4 and tetrahydrofuran (THF) with dimethyl sulfoxide (DMSO) was used as the porogen. The morphology of the imprinted membranes after template extracting is much rougher with big cavities than that of the non‐imprinted membranes (NIMs) and the imprinted membranes before template extracting. The MIMs can selectively separate the magnolol.     

明胶/聚乳酸复合纤维膜的制备、表征及作为角膜细胞载体的评价

利用静电纺丝技术制备了明胶与聚乳酸的复合纤维膜, 研究了组分配比对复合膜的表面性能、孔隙结构和力学性能的影响, 并以复合膜为组织工程支架进行兔角膜上皮细胞的体外培养. 采用扫描电子显微镜、免疫荧光染色和噻唑蓝四氮唑溴化物(MTT)比色法综合评价了细胞在支架表面的黏附与增殖能力. 结果表明, 纺丝溶液的组分对纤维的直径分布和表面亲水性有显著影响, 不同组分配比的复合纤维膜均具有高孔隙率的通孔结构; 以明胶为基材可维持复合膜的细胞黏附性; 与聚乳酸复合可以明显提高复合膜的力学性能.     

Properties of Poly(Vinyl Alcohol)‐Based Composite Membranes for Direct Methanol Fuel Cell Applications

The feasibility of poly(vinyl alcohol)(PVA)/sulfosuccinic acid(SSA)/heteropolyacid (HPA) composite membranes was investigated to apply for direct methanol fuel cells (DMFC). The composite membranes were prepared by the solution casting method and their properties were examined. The FTIR spectra showed that the Keggin unit of HPA was preserved in the composite membranes and that specific interactions were involved between PVA and HPA. The composite membranes showed uniform distribution of PWA particles in the PVA/SSA/PWA composite membranes by FE‐SEM. The HPA bleeding out was observed to decrease with increasing HPA concentration. The proton conductivity of PVA/SSA/HPA composite membranes improved at low HPA concentration (5‐10 wt.%), while those properties decreased as HPA concentration increased over 10 wt.%.     

Membranes obtained by preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene–perfluorovinyl ether)

Some properties of the membranes obtained by preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene-perfluorovinyl ether) copolymer (PFA) films have been investigated. The dimensional change caused by grafting and swelling behavior, water uptake, electrical conductivity, and mechanical properties of the grafted films were found to increase as the grafting proceeds. The influence of the preparation conditions (such as preirradiation dose, monomer concentration, grafting temperature, and film thickness) on those properties was studied. These properties were found to be dependent mainly on the degree of grafting regardless of grafting conditions, except at higher monomer concentration (>40 wt %). The electric conductivity and mechanical properties for the membranes obtained at higher AAc concentrations were lower than those obtained at lower ones. Analysis by x-ray microscopy of the grafted films revealed that the grafting begins at the part close to the film surface and proceeds into the central part with progressive diffusion of monomer to give finally homogeneous distribution of the electrolytes in the whole bulk of the polymer. The membranes show good electrochemical and mechanical properties which make them acceptable for practical use as cation-exchange membranes.     

酸碱型磺化聚芳醚腈酮质子交换膜材料的性能研究

以合成的一系列不同磺化度的碘化聚芳醚腈酮(SPPENKs)为acidic聚合物,以聚芳醚酰亚胺(PEI)为basic聚合物,并将其溶解在N-甲基-2-吡咯烷酮(NMP)中配成质量分数为10%的成膜液,60℃下刮制成膜,制得acid-base型磺化聚芳醚腈酮质子导电了聚合物膜.用红外(FT-IR)谱图表征了acid-base型质子导电聚合物的结构,并测试了acid-base型质子导电聚合物膜的溶胀率、含水率、水解、氧化和热稳定性以及膜材料的离子交换容量IEC(IEC=meqSO3H/gdrymembrane)值等.测试结果初步表明新型质子导电聚合物膜具有良好的物化性能和较高的质子导电性,在80℃下acid-base型质子导电聚合物膜的水解断裂时间除SPPENK-40/PEI外,都超过2000h;SPPENK-60/PEI和SPPENK-80/PEI膜(IEC分别为1·08mmol/g、1·32mmol/g)与Nafion117相比,在具有较高质子交换能力的同时具有较低的溶胀率。     

Correlation Between Structure and Transport Properties of Polymeric Membranes for Immunoisolation

Laboratory-made asymmetric polyurethane membranes designed for immunoisolation were investigated. Two types of EK and ES membranes were prepared in different spinning conditions. The membrane structure was characterised by the skin pore radius measurements using differential scanning calorimetry (DSC). Diffusive transport properties of membranes were determined by in vitro method for albumin and creatinine. The scanning electron microscopy (SEM) was applied to study the morphology of membranes. It has been found that the DSC technique is a useful tool for the evaluation of pore radii in the skin layer for PU membranes. Calculated pore radii were in the range from 1.95 to 2.47 nm for the EK and ES types. A correlation between the skin pore radii and the transport properties was not found in this case of investigated membranes. However, the transport properties data can serve for the estimation of selectivity of membranes. Thus, the selectivity of membranes for solutes of various molecular size was estimated from the D _m/D _w ratio of diffusion coefficients for albumin and creatinine. The SEM micrographs reveal the finger-like internal structure of capillary membranes, as well as various skin thickness. This revised version was published online in July 2006 with corrections to the Cover Date.