Identification and correction of spectral contamination in 2H/1H and 18O/16O measured in leaf, stem, and soil water

Plant water extracts typically contain organic materials that may cause spectral interference when using isotope ratio infrared spectroscopy (IRIS), resulting in errors in the measured isotope ratios. Manufacturers of IRIS instruments have developed post-processing software to identify the degree of contamination in water samples, and potentially correct the isotope ratios of water with known contaminants. Here, the correction method proposed by an IRIS manufacturer, Los Gatos Research, Inc., was employed and the results were compared with those obtained from isotope ratio mass spectrometry (IRMS). Deionized water was spiked with methanol and ethanol to create correction curves for δ(18)O and δ(2)H. The contamination effects of different sample types (leaf, stem, soil) and different species from agricultural fields, grasslands, and forests were compared. The average corrections in leaf samples ranged from 0.35 to 15.73‰ for δ(2)H and 0.28 to 9.27‰ for δ(18)O. The average corrections in stem samples ranged from 1.17 to 13.70‰ for δ(2)H and 0.47 to 7.97‰ for δ(18)O. There was no contamination observed in soil water. Cleaning plant samples with activated charcoal had minimal effects on the degree of spectral contamination, reducing the corrections, by on average, 0.44‰ for δ(2)H and 0.25‰ for δ(18)O. The correction method eliminated the discrepancies between IRMS and IRIS for δ(18)O, and greatly reduced the discrepancies for δ(2)H. The mean differences in isotope ratios between IRMS and the corrected IRIS method were 0.18‰ for δ(18)O, and -3.39‰ for δ(2)H. The inability to create an ethanol correction curve for δ(2)H probably caused the larger discrepancies. We conclude that ethanol and methanol are the primary compounds causing interference in IRIS analyzers, and that each individual analyzer will probably require customized correction curves.     

Continuous analysis of δ18O and δD values of water by diffusion sampling cavity ring‐down spectrometry: a novel sampling device for unattended field monitoring of precipitation,ground and surface waters

A novel sampling device suitable for continuous, unattended field monitoring of rapid isotopic changes in environmental waters is described. The device utilises diffusion through porous PTFE tubing to deliver water vapour continuously from a liquid water source for analysis of δ¹⁸O and δD values by Cavity Ring‐Down Spectrometry (CRDS). Separation of the analysed water vapour from non‐volatile dissolved and particulate contaminants in the liquid sample minimises spectral interferences associated with CRDS analyses of many aqueous samples. Comparison of isotopic data for a range of water samples analysed by Diffusion Sampling‐CRDS (DS‐CRDS) and Isotope Ratio Mass Spectrometry (IRMS) shows significant linear correlations between the two methods allowing for accurate standardisation of DS‐CRDS data. The internal precision for an integration period of 3 min (standard deviation (SD) = 0.1 ‰ and 0.3 ‰ for δ¹⁸O and δD values, respectively) is similar to analysis of water by CRDS using an autosampler to inject and evaporate discrete water samples. The isotopic effects of variable air temperature, water vapour concentration, water pumping rate and dissolved organic content were found to be either negligible or correctable by analysis of water standards. The DS‐CRDS system was used to analyse the O and H isotope composition in short‐lived rain events. Other applications where finely time resolved water isotope data may be of benefit include recharge/discharge in groundwater/river systems and infiltration‐related changes in cave drip water. Copyright © 2011 John Wiley & Sons, Ltd.     

Concentration effects on laser-based δ18 O and δ2 H measurements and implications for the calibration of vapour measurements with liquid standards

Recently available isotope ratio infrared spectroscopy can directly measure the isotopic composition of atmospheric water vapour (δ¹⁸O, δ²H), overcoming one of the main limitations of isotope ratio mass spectrometry (IRMS) methods. Calibrating these gas‐phase instruments requires the vapourisation of liquid standards since primary standards in principle are liquids. Here we test the viability of calibrating a wavelength‐scanned cavity ring‐down spectroscopy (CRDS) instrument with vapourised liquid standards. We also quantify the dependency of the measured isotope values on the water concentration for a range of isotopic compositions. In both liquid and vapour samples, we found an increase in δ¹⁸O and δ²H with water vapour concentration. For δ¹⁸O, the slope of this increase was similar for liquid and vapour, with a slight positive relationship with sample δ‐value. For δ²H, we found diverging patterns for liquid and vapour samples, with no dependence on δ‐value for vapour, but a decreasing slope for liquid samples. We also quantified tubing memory effects to step changes in isotopic composition, avoiding concurrent changes in the water vapour concentration. Dekabon tubing exhibited much stronger, concentration‐dependent, memory effects for δ²H than stainless steel or perfluoroalkoxy (PFA) tubing. Direct vapour measurements with CRDS in a controlled experimental chamber agreed well with results obtained from vapour simultaneously collected in cold traps analysed by CRDS and IRMS. We conclude that vapour measurements can be calibrated reliably with liquid standards. We demonstrate how to take the concentration dependencies of the δ‐values into account. Copyright © 2010 John Wiley & Sons, Ltd.     

Detailed assessment of isotope ratio infrared spectroscopy and isotope ratio mass spectrometry for the stable isotope analysis of plant and soil waters

As an alternative to isotope ratio mass spectrometry (IRMS), the isotope ratio infrared spectroscopy (IRIS) approach has the advantage of low cost, continuous measurement and the capacity for field‐based application for the analysis of the stable isotopes of water. Recent studies have indicated that there are potential issues of organic contamination of the spectral signal in the IRIS method, resulting in incorrect results for leaf samples. To gain a more thorough understanding of the effects of sample type (e.g., leaf, root, stem and soil), sample species, sampling time and climatic condition (dry vs. wet) on water isotope estimates using IRIS, we collected soil samples and plant components from a number of major species at a fine temporal resolution (every 2 h for 24–48 h) across three locations with different climatic conditions in the Heihe River Basin, China. The hydrogen and oxygen isotopic compositions of the extracted water from these samples were measured using both an IRMS and an IRIS instrument. The results show that the mean discrepancies between the IRMS and IRIS approaches for δ¹⁸O and δD, respectively, were: –5.6‰ and ?75.7‰ for leaf water; –4.0‰ and ?23.3‰ for stem water; –3.4‰ and ?28.2‰ for root water; ?0.5‰ and –6.7‰ for xylem water; –0.06‰ and ?0.3‰ for xylem flow; and ?0.1‰ and 0.3‰ for soil water. The order of the discrepancy was: leaf > stem ≈ root > xylem > xylem flow ≈ soil. In general, species of the same functional types (e.g., woody vs. herbaceous) within similar habitats showed similar deviations. For different functional types, the differences were large. Sampling at nighttime did not remove the observed deviations. Copyright © 2011 John Wiley & Sons, Ltd.     

Geographical traceability of wheat and its products using multielement light stable isotopes coupled with chemometrics

The present study was aimed to investigate the variation of stable isotopic ratios of carbon, nitrogen, hydrogen, and oxygen in wheat kernel along with different processed fractions from three geographical origins across 5 years using isotope ratio mass spectrometry (IRMS). Multiway ANOVA revealed significant differences among region, harvest year, processing, and their interactions for all isotopes. The region contributed the major variability in the δ¹³C ‰, δ²H ‰, δ¹⁵N ‰, and δ¹⁸O‰ values of wheat. Variation of δ¹³C ‰, δ¹⁵N ‰, and δ¹⁸O ‰ between wheat whole kernel and its products (break, reduction, noodles, and cooked noodles) were ?0.7‰, and no significant difference was observed, suggesting the reliability of these isotope fingerprints in geographical traceability of wheat‐processed fractions and foods. A significant influence of wheat processing was observed for δ²H values. By applying linear discriminant analysis (LDA) to the whole dataset, the generated model correctly classified over 91% of the samples according to the geographical origin. The application of these parameters will assist in the development of an analytical control procedure that can be utilized to control the mislabeling regarding geographical origin of wheat kernel and its products.     

Discrepancies between isotope ratio infrared spectroscopy and isotope ratio mass spectrometry for the stable isotope analysis of plant and soil waters

The use of isotope ratio infrared spectroscopy (IRIS) for the stable hydrogen and oxygen isotope analysis of water is increasing. While IRIS has many advantages over traditional isotope ratio mass spectrometry (IRMS), it may also be prone to errors that do not impact upon IRMS analyses. Of particular concern is the potential for contaminants in the water sample to interfere with the spectroscopy, thus leading to erroneous stable isotope data. Water extracted from plant and soil samples may often contain organic contaminants. The extent to which contaminants may interfere with IRIS and thus impact upon data quality is presently unknown. We tested the performance of IRIS relative to IRMS for water extracted from 11 plant species and one organic soil horizon. IRIS deviated considerably from IRMS for over half of the samples tested, with deviations as large as 46‰ (δ²H) and 15.4‰ (δ¹⁸O) being measured. This effect was reduced somewhat by using activated charcoal to remove organics from the water; however, deviations as large as 35‰ (δ²H) and 11.8‰ (δ¹⁸O) were still measured for these cleaned samples. Interestingly, the use of activated charcoal to clean water samples had less effect than previously thought for IRMS analyses. Our data show that extreme caution is required when using IRIS to analyse water samples that may contain organic contaminants. We suggest that the development of new cleaning techniques for removing organic contaminants together with instrument‐based software to flag potentially problematic samples are necessary to ensure accurate plant and soil water analyses using IRIS. Copyright © 2010 John Wiley & Sons, Ltd.     

Measurements of water vapor isotope ratios with wavelength-scanned cavity ring-down spectroscopy technology: new insights and important caveats for deuterium excess measurements in tropical areas in comparison with isotope-ratio mass spectrometry

The new infrared laser spectroscopic techniques enable us to measure the isotopic composition (δ(18)O and δ(2)H) of atmospheric water vapor. With the objective of monitoring the isotopic composition of tropical water vapor (West Africa, South America), and to discuss deuterium excess variability (d=δ(2)H - 8δ(18)O) with an accuracy similar to measurements arising from isotope-ratio mass spectrometry (IRMS), we have conducted a number of tests and calibrations using a wavelength-scanned cavity ring-down spectroscopy (WS-CRDS) technique. We focus in this paper on four main aspects regarding (1) the tubing material, (2) the humidity calibration of the instrument, (3) the water vapor concentration effects on δ, and (4) the isotopic calibration of the instrument. First, we show that Synflex tubing strongly affects δ(2)H measurements and thus leads to unusable d values. Second, we show that the mixing ratio as measured by WS-CRDS has to be calibrated versus atmospheric mixing ratio measurements and we also suggest possible non-linear effects over the whole mixing ratio range (~2 to 20 g/kg). Third, we show that significant non-linear effects are induced by water vapor concentration variations on δ measurements, especially for mixing ratios lower than ~5 g/kg. This effect induces a 5 to 10‰ error in deuterium excess and is instrument-dependent. Finally, we show that an isotopic calibration (comparison between measured and true values of isotopic water standards) is needed to avoid errors on deuterium excess that can attain ~10‰.     

Hydrogen and oxygen isotope values in hydrogen peroxide

Hydrogen peroxide (H(2)O(2)) is a widely used oxidizer with many commercial applications; unfortunately, it also has terrorist-related uses. We analyzed 97 hydrogen peroxide solutions representing four grades purchased across the United States and in Mexico. As expected, the range of hydrogen (δ(2)H, 230‰) and oxygen (δ(18)O, 24‰) isotope values of the H(2)O(2) solutions was large, reflecting the broad isotopic range of dilution waters. This resulted in predictable linear relationships of δ(2)H and δ(18)O values of H(2)O(2) solutions that were near parallel to the Meteoric Water Line (MWL), offset by the concentration of H(2)O(2) in the solution. By grade, dilute (3 to 35%) H(2)O(2) solutions were not statistically different in slope. Although the δ(2)H values of manufactured H(2)O(2) could be different from those of water, rapid H(2)O(2)-H(2)O exchange of H atoms eliminated any distinct isotope signal. We developed a method to measure the δ(18)O value of H(2)O(2) independent of dilution water by directly measuring O(2) gas generated from a catalase-induced disproportionation reaction. We predicted that the δ(18)O values of H(2)O(2) would be similar to that of atmospheric oxygen (+23.5‰), the predominant source of oxygen in the most common H(2)O(2) manufacturing process (median disproportionated δ(18)O=23.8‰). The predictable H-O relationships in H(2)O(2) solutions make it possible to distinguish commercial dilutions from clandestine concentration practices. Future applications of this work include synthesis studies that investigate the chemical link between H(2)O(2) reagents and peroxide-based explosive products, which may assist law enforcement in criminal investigations.     

Adaptation of continuous‐flow cavity ring‐down spectroscopy for batch analysis of δ13C of CO2 and comparison with isotope ratio mass spectrometry

Measurements of δ¹³C in CO₂ have traditionally relied on samples stored in sealed vessels and subsequently analyzed using magnetic sector isotope ratio mass spectrometry (IRMS), an accurate but expensive and high‐maintenance analytical method. Recent developments in optical spectroscopy have yielded instruments that can measure δ¹³CO₂ in continuous streams of air with precision and accuracy approaching those of IRMS, but at a fraction of the cost. However, continuous sampling is unsuited for certain applications, creating a need for conversion of these instruments for batch operation. Here, we present a flask (syringe) adaptor that allows the collection and storage of small aliquots (20–30 mL air) for injection into the cavity ring‐down spectroscopy (CRDS) instrument. We demonstrate that the adaptor's precision is similar to that of traditional IRMS (standard deviation of 0.3‰ for 385 ppm CO₂ standard gas). In addition, the concentration precision (±0.3% of sample concentration) was higher for CRDS than for IRMS (±7% of sample concentration). Using the adaptor in conjunction with CRDS, we sampled soil chambers and found that soil‐respired δ¹³C varied between two different locations in a piñon‐juniper woodland. In a second experiment, we found no significant discrimination between the respiration of a small beetle (~5 mm) and its diet. Our work shows that the CRDS system is flexible enough to be used for the analysis of batch samples as well as for continuous sampling. This flexibility broadens the range of applications for which CRDS has the potential to replace magnetic sector IRMS. Copyright © 2011 John Wiley & Sons, Ltd.     

δ18O anchoring to VPDB: calcite digestion with 18O-adjusted ortho-phosphoric acid

For anchoring CO(2) isotopic measurements on the δ(18)O(VPD-CO2) scale, the primary reference material (NBS 19 calcite) needs to be digested using concentrated ortho-phosphoric acid. During this procedure, great care must be taken to ensure that the isotopic composition of the liberated gas is accurate. Apart from controlling the reaction temperature to ±0.1 °C, the potential for oxygen isotope exchange between the produced CO(2) and water must be kept to a minimum. The water is usually assumed to reside on the walls in the headspace of the reaction vessel. We demonstrate here that a large fraction of the exchange may also occur with water inside the acid. Our results indicate that both exchange reactions have a significant impact on the results and may have largely been responsible for scale inconsistencies between laboratories in the past. The extent of CO(2)/H(2)O oxygen exchange depends on the concentration (amount of free water) in the acid. For acids with a nominal H(3)PO(4) mass fraction of less than 102%, oxygen isotope exchange can create a substantial isotopic bias during high-precision measurements with the degree of the alteration being proportional to the effective isotopic contrast between the acid and the CO(2) released from the calcite. Water evaporating from the acid at 25 °C has a δ(18)O value of -34.5‰ relative to the isotopic composition of the whole acid. This large fractionation is likely to occur in two steps; by exchange with phosphate, water inside the acid is decreased in oxygen-18 relative to the bulk acid by ～ -22‰. This water is then fractionated further during evaporation. Oxygen exchange with both water inside the acid and water condensate in the headspace can contribute to the measured isotopic signature depending on the experimental parameters. The system employed for this study has been specifically designed to minimize oxygen exchange with water. However, the amount of altered CO(2) for a 95% H(3)PO(4) at 25 °C still accounts for about 3% of the total CO(2) produced from a 40 mg calcite sample, resulting in a δ(18) O range of about 0.8‰ when varying the δ(18)O value of the acid by 25‰. Least biased results for NBS19-CO(2) were obtained for an acid with a δ(18)O value close to +23‰ vs. VSMOW. In contrast, commercial acids from several sources had an average δ(18)O value of +13‰, amounting to a 10‰ offset from the optimal value. This observation suggests that the well-known scale incompatibilities between laboratories could arise from this difference with measurements that may have suffered systematically from non-optimal acid-δ(18)O values, thus producing variable offsets, depending on the experimental details. As a remedy, we suggest that the δ(18)O of phosphoric acid reacted with calcites for establishing a δ(18)O scale anchor be adjusted, and this should reduce the variability of the δ(18)O of CO(2) evolved in acid digestion to less than ±0.05‰. The adjustment should be made by taking into account the difference in δ(18)O between the calcite-CO(2) and the acid, with a target difference of 16‰. With this strategy, agreement between δ(18)O scales based on water, atmospheric CO(2) , and carbonates as well as data compatibility between laboratories may be substantially improved.     

Doubly labeled water analysis using cavity ring-down spectroscopy

The doubly labeled water method provides an objective and accurate measure of total energy expenditure in free‐living subjects and is considered the gold‐standard method for this measurement. Its use, however, is limited by the need to employ isotope ratio mass spectrometry (IRMS) to obtain the high‐precision isotopic abundance analyses needed to optimize the dose of expensive ¹⁸O‐labeled water. Recently, cavity‐ring down spectroscopy (CRDS) instruments have become commercially available and may serve as a less expensive alternative to IRMS. We compared the precision and accuracy of CRDS with those of IRMS for the measurement of total energy expenditure from urine specimens in 14 human subjects. The relative accuracy and precision (SD) for total body water was 0.5 ± 1% and for total energy expenditure was 0.5 ± 6%. The CRDS instrument displayed a memory between successive specimens of 5% for ¹⁸O and 9% for ²H. The memory necessitated carefully ordering of specimens to reduce isotopic disparity, performance of several injections of each specimen to condition the analyzer, and use of a mathematical memory correction on subsequent injections. These limited the specimen throughput to about one urine specimen per hour. CRDS provided accuracy and precision for isotope abundance measurements of urine that were comparable with those of IRMS. The memory problems were easily recognized by our experienced laboratory staff, but future efforts should be aimed at reducing the memory of the CRDS so that it would be less likely to result in poor reproducibility in laboratories using doubly labeled water for the first time. Copyright © 2010 John Wiley & Sons, Ltd.     

A new isolation procedure of nitrate from freshwater for nitrogen and oxygen isotope analysis

The nitrogen (δ¹⁵N) and oxygen isotope (δ¹⁸O) analysis of nitrate (NO₃^–) from aqueous samples can be used to determine nitrate sources and to study N transformation processes. For these purposes, several methods have been developed; however, none of them allows an accurate, fast and inexpensive analysis. Here, we present a new simple method for the isolation of nitrate, which is based on the different solubilities of inorganic salts in an acetone/hexane/water mixture. In this solvent, all major nitrate salts are soluble, whereas all other oxygen‐bearing compounds such as most inorganic carbonates, sulfates, and phosphates are not. Nitrate is first concentrated by freeze‐drying, dissolved in the ternary solvent and separated from insoluble compounds by centrifugation. Anhydrous barium nitrate is then precipitated in the supernatant solution by adding barium iodide. For δ¹⁸O analysis, dried Ba(NO₃)₂ samples are directly reduced in a high‐temperature conversion system to CO and measured on‐line using isotope ratio mass spectrometry (IRMS). For δ¹⁵N analysis, samples are combusted in an elemental analyzer (EA) coupled to an IRMS system. The method has been tested down to 20 µmol NO₃^– with a reproducibility (1SD) of 0.1‰ for nitrogen and 0.2–0.4‰ for oxygen isotopes. For nitrogen we observed a small consistent ¹⁵N enrichment of +0.2‰, probably due to an incomplete precipitation process and, for oxygen, a correction for the incorporation of water in the precipitated Ba(NO₃)₂ has to be applied. Apart from being robust, this method is highly efficient and low in cost. Copyright © 2011 John Wiley & Sons, Ltd.     

Discrimination between ginseng from Korea and China by light stable isotope analysis

Ginseng is a health food and traditional medicine highly valued in Asia. Ginseng from certain origins is higher valued than from other origins, so that a reliable method for differentiation of geographical origin is important for the economics of ginseng production. To discriminate between ginseng samples from South Korea and PR China, 29 samples have been analyzed for the isotopic composition of the elements H, C and N. The results showed δ(2)H values between -94 and -79‰, for δ(13)C -27.9 to -23.7‰ and for δ(15)N 1.3-5.4‰ for Chinese ginseng. Korean ginseng gave δ(2)H ratios between -91 and -69‰, δ(13)C ratios between -31.2 and -22.4‰ and δ(15)N ratios between -2.4 and +7‰. Despite the overlap between the values for individual isotopes, a combination of the isotope systems gave a reasonable differentiation between the two geographic origins. Especially the statistically significant difference in δ(2)H ratios facilitated the differentiation between Korean and Chinese ginseng samples.     

Hydrogen isotope correction for laser instrument measurement bias at low water vapor concentration using conventional isotope analyses: application to measurements from Mauna Loa Observatory, Hawaii

The hydrogen and oxygen isotope ratios of water vapor can be measured with commercially available laser spectroscopy analyzers in real time. Operation of the laser systems in relatively dry air is difficult because measurements are non-linear as a function of humidity at low water concentrations. Here we use field-based sampling coupled with traditional mass spectrometry techniques for assessing linearity and calibrating laser spectroscopy systems at low water vapor concentrations. Air samples are collected in an evacuated 2 L glass flask and the water is separated from the non-condensable gases cryogenically. Approximately 2 μL of water are reduced to H(2) gas and measured on an isotope ratio mass spectrometer. In a field experiment at the Mauna Loa Observatory (MLO), we ran Picarro and Los Gatos Research (LGR) laser analyzers for a period of 25 days in addition to periodic sample collection in evacuated flasks. When the two laser systems are corrected to the flask data, they are strongly coincident over the entire 25 days. The δ(2)H values were found to change by over 200‰ over 2.5 min as the boundary layer elevation changed relative to MLO. The δ(2)H values ranged from -106 to -332‰, and the δ(18)O values (uncorrected) ranged from -12 to -50‰. Raw data from laser analyzers in environments with low water vapor concentrations can be normalized to the international V-SMOW scale by calibration to the flask data measured conventionally. Bias correction is especially critical for the accurate determination of deuterium excess in dry air.     

An inexpensive, fast, and reliable method for vacuum extraction of soil and plant water for stable isotope analyses by mass spectrometry

The stable isotopes of water (hydrogen and oxygen isotopes) are of utmost interest in ecology and the geosciences. In many cases water has to be extracted directly from a matrix such as soil or plant tissue before isotopes can be analyzed by mass spectrometry. Currently, the most widely used technique for water is cryogenic vacuum extraction. We present a simple and inexpensive modification of this method and document tests conducted with soils of various grain size and tree core replicates taken on four occasions during 2010. The accuracies for sandy soils are between 0.4‰ and 3‰ over a range of 21‰ and 165‰ for δ¹⁸O and δ²H, respectively. Spiking tests with water of known isotope composition were conducted with soil and tree core samples; they indicate reliable precision after an extraction time of 15 min for sandy soils. For clayey soils and tree cores, the deviations were up to 0.63‰ and 4.7‰ for δ¹⁸O and δ²H, respectively. This indicates either that the extraction time should be extended or that mechanisms different from Rayleigh fractionation play a role. The modified protocol allows a fast and reliable extraction of large numbers of water samples from soil and plant material in preparation for stable isotope analyses. Copyright © 2011 John Wiley & Sons, Ltd.     

Spectral analysis software improves confidence in plant and soil water stable isotope analyses performed by isotope ratio infrared spectroscopy (IRIS)

Previous studies have demonstrated the potential for large errors to occur when analyzing waters containing organic contaminants using isotope ratio infrared spectroscopy (IRIS). In an attempt to address this problem, IRIS manufacturers now provide post-processing spectral analysis software capable of identifying samples with the types of spectral interference that compromises their stable isotope analysis. Here we report two independent tests of this post-processing spectral analysis software on two IRIS systems, OA-ICOS (Los Gatos Research Inc.) and WS-CRDS (Picarro Inc.). Following a similar methodology to a previous study, we cryogenically extracted plant leaf water and soil water and measured the δ(2)H and δ(18)O values of identical samples by isotope ratio mass spectrometry (IRMS) and IRIS. As an additional test, we analyzed plant stem waters and tap waters by IRMS and IRIS in an independent laboratory. For all tests we assumed that the IRMS value represented the "true" value against which we could compare the stable isotope results from the IRIS methods. Samples showing significant deviations from the IRMS value (>2σ) were considered to be contaminated and representative of spectral interference in the IRIS measurement. Over the two studies, 83% of plant species were considered contaminated on OA-ICOS and 58% on WS-CRDS. Post-analysis, spectra were analyzed using the manufacturer's spectral analysis software, in order to see if the software correctly identified contaminated samples. In our tests the software performed well, identifying all the samples with major errors. However, some false negatives indicate that user evaluation and testing of the software are necessary. Repeat sampling of plants showed considerable variation in the discrepancies between IRIS and IRMS. As such, we recommend that spectral analysis of IRIS data must be incorporated into standard post-processing routines. Furthermore, we suggest that the results from spectral analysis be included when reporting stable isotope data from IRIS.     

反硝化细菌法结合痕量气体分析仪/同位素比质谱仪分析水体硝酸盐氮同位素组成

建立了反硝化细菌法结合疫量气体分析仪(TraceGas)/同位素比质谱仪分析水体硝酸盐氮同位素组成的方法.对反硝化细菌生长、培养条件和方法的精密度及稳定性进行了分析,并利用标准样品USGS34研究了样品反硝化孵育时间、TraceGas捕集N2O气体时间对δ15N测定的影响.结果表明:恰当的氧气量才能培养出有效的反硝化细菌;本方法精密度及稳定性较好,同一制备时间内硝酸盐δ15N的SD在0.09‰～0.14‰之间,6个月内SD为0.12‰;样品反硝化孵育3～24 h可以得到稳定的δ15N; TraceGas捕集时间为500 s时得到的δ15N校正值与真实值最接近.应用本方法对养殖场污水和灌溉井水的硝酸盐δ15N进行了测定.     

A new Chinese national reference material (GBW04481) for calcite oxygen and carbon isotopic microanalysis

Carbonate oxygen (O) and carbon (C) isotopes are widely used as proxies for tracing the processes and physicochemical conditions of many geological events and environmental changes in Earth Science. In particular, O and C isotopic variations at micrometer scales revealed by modern microbeam analytical techniques such as SIMS and NanoSIMS are robust archives for reconstructing palaeoenvironment and paleoclimate changes at annual and seasonal resolution or even higher temporal resolution. Widespread application of carbonate O and C isotopic microanalysis in Earth Sciences, however, has been restricted due to limitation of high-quality carbonate reference materials for O and C isotopic microanalysis. We introduce in this paper a new calcite reference material for calcite O and C isotopic microanalysis. This calcite is collected from a drill-core of the Oka carbonatite complex (Quebec, Canada). We demonstrated that the Oka calcite is fairly homogeneous in O and C isotopic compositions at micrometer scales based on homogeneity test by hundreds of SIMS O and C isotopic analyses. Precise determinations by using conventional gas-source IRMS yield the recommended value of δ¹⁸O_VPDB = −23.12 ± 0.15‰ (1SD) and δ¹³C_VPDB = −5.23 ± 0.06‰ (1SD) for the Oka calcite, which has been certified as the first class of Chinese national certified reference material (GBW04481) for O and C isotopic microanalysis.     

Improved online hydrogen isotope analysis of halite aqueous inclusions

We demonstrate an improved method based on continuous‐flow elemental analyser pyrolysis isotopic ratio mass spectrometry (CF‐EA‐PY‐IRMS) to measure the ²H/¹H ratios of water trapped in halite crystals. Two challenges to overcome are the low hydrogen concentration of samples (10‐50 μmol H₂·g^?1) and the high chloride concentration released when reacting halite in an elemental analyser. We describe an optimization procedure for determining the ²H/¹H ratio of this trapped water with an acceptable accuracy. This technique involves the use of a high‐temperature Cr reactor to quantitatively convert H₂O into H₂. The initial step was performed on halite crystals precipitated from a water reservoir where ²H/¹H ratios were monitored from its initial stage until the end of evaporation. The ²H/¹H isotopic analyses were automated online in continuous‐flow mode. Precision of the method was determined for those “synthetic” samples with hydrogen concentrations ranging from 0.2 to 0.5 wt%. ²H/¹H isotopic ratios of evaporating waters bracket the compositions of water inclusions. The formation of fluid inclusions is not instantaneous and records the isotopic signature of the residual waters across a time range during which the isotopic values of the water still evolve. This property explains why the δ²H_VSMOW standard deviation of ±5‰ (2σ) observed for 10‐mg aliquots of halite exceeds the instrumental error (about ±1.5‰ 2σ) determined on the basis of IAEA‐CH7, NBS 30, and NBS 22 references along with calibrated waters with and without added halite crystals. We also applied this method to Mesoproterozoic (1.4 Ga) and Neoproterozoic (0.8 Ga) halite samples with relatively low hydrogen concentrations (300‐1500 ppm). The measured δ²H_VSMOW values for Precambrian waters range from ?89‰ to ?54‰. We propose that this technique offers a new perspective and great potential for palaeoenvironmental reconstructions based on the ²H/¹H analyses of water trapped in halite.     

D and 18O enrichment measurements in biological fluids in a continuous-flow elemental analyser with an isotope-ratio mass spectrometer using two configurations

In doubly labelled water studies, biological sample enrichments are mainly measured using off-line techniques (equilibration followed by dual-inlet introduction) or high-temperature elemental analysis (HT-EA), coupled with an isotope-ratio mass spectrometer (IRMS). Here another continuous-flow method, (CF-EA/IRMS), initially dedicated to water, is tested for plasma and urine analyses.The elemental analyser configuration is adapted for each stable isotope: chromium tube for deuterium reduction and glassy carbon reactor for 18O pyrolysis. Before on-line conversion of water into gas, each matrix is submitted to a short and easy treatment, which is the same for the analysis of the two isotopes. Plasma is passed through centrifugal filters. Urine is cleaned with black carbon and filtered (0.45 microm diameter).Tested between 150 and 300 ppm in these fluids, the D/H ratio response is linear with good repeatability (SD<0.2 ppm) and reproducibility (SD<0.5 ppm). For 18O/16O ratios (from 2000 to 2200 ppm), the same repeatability is obtained with a between-day precision lower than 1.4 ppm. The accuracy on biological samples is validated by comparison to classical dual-inlet methods: 18O analyses give more accurate results. The data show that enriched physiological fluids can be successfully analysed in CF-EA/IRMS.