壳聚糖铜(Ⅱ)配位与氧化控制降解寡糖的GFC色谱研究

在壳聚糖溶液中加入铜离子使形成壳聚糖铜配合物,通过IR,UV,元素分析及热重分析等对壳聚糖铜配合物进行表征。用H₂O₂对形成的壳聚糖Cu(Ⅱ)配合物进行氧化降解,测定了降解产物寡糖的平均数均分子量和分子量分布。结果表明壳聚糖铜配合物在升高温度时,在过氧化氢的存在下降解迅速,降解从大分子量范围开始,降解寡糖分子量分布在温度和降解时间相同条件下大大窄于目前常用的盐酸和纯过氧化氢氧化降解方法。分子量分布指数与降解寡糖的平均数均分子量有关,当高于10个寡聚糖数(DP)时,DP越小,分子量分布指数越小。     

Liposome destruction by hydrodynamic cavitation in comparison to chemical,physical and mechanical treatments

Liposomes are widely applied in research, diagnostics, medicine and in industry. In this study we show for the first time the effect of hydrodynamic cavitation on liposome stability and compare it to the effect of well described chemical, physical and mechanical treatments. Fluorescein loaded giant 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) lipid vesicles were treated with hydrodynamic cavitation as promising method in inactivation of biological samples. Hydrodynamic treatment was compared to various chemical, physical and mechanical stressors such as ionic strength and osmolarity agents (glucose, Na⁺, Ca²⁺, and Fe³⁺), free radicals, shear stresses (pipetting, vortex mixing, rotational shear stress), high pressure, electroporation, centrifugation, surface active agents (Triton X-100, ethanol), microwave irradiation, heating, freezing-thawing, ultrasound (ultrasonic bath, sonotrode). The fluorescence intensity of individual fluorescein loaded lipid vesicles was measured with confocal laser microscopy. The distribution of lipid vesicle size, vesicle fluorescence intensity, and the number of fluorescein loaded vesicles was determined before and after treatment with different stressors. The different environmental stressors were ranked in order of their relative effect on liposome fluorescein release. Of all tested chemical, physical and mechanical treatments for stability of lipid vesicles, the most detrimental effect on vesicles stability had hydrodynamic cavitation, vortex mixing with glass beads and ultrasound. Here we showed, for the first time that hydrodynamic cavitation was among the most effective physico-chemical treatments in destroying lipid vesicles. This work provides a benchmark for lipid vesicle robustness to a variety of different physico-chemical and mechanical parameters important in lipid vesicle preparation and application.     

Depolymerization using sonochemical reactors: A critical review

Ultrasonic irradiation has been proposed as a novel approach for degradation of polymer compounds, especially considering the fact that the reduction in the molecular weight (also the intrinsic viscosity) is simply by splitting the most susceptible chemical bond without causing any changes in the chemical nature. An overview of the application of ultrasound for the polymer degradation has been presented in this work, discussing the mechanism of degradation, kinetic modeling, effect of operating parameters and the type of reactors generally used for depolymerization. The effect of important operating parameters such as initial polymer concentration, presence of functional groups in the polymer chain, reaction volume, initial molecular weight, temperature, operating frequency, power dissipation and use of process intensifying additives have been discussed also giving guidelines about selection of the optimum parameters. It has been observed that the low concentrations and higher power dissipation (till an optimum) are favorable resulting in higher extents of degradation. Typically low frequency is recommended but for the case of water soluble polymers, higher frequencies would also give similar results due to the dominant action of chemical effects of cavitation. It has been demonstrated that the alkyl group substituent also affects the degradation rate of polymer. An overview of degradation using combined approach based on ultrasound and additives with comparison with individual approach has also been presented. It has been observed that the main contributing factor for the synergy of the combined approach is the selection of optimum loading of additives. Overall, it has been observed that efficient polymer degradation can be achieved using combined process based on the use of ultrasound.     

Radiation Degradation of Polypropylene-Molecular Weight and Melt Viscosity Change

Isotactic polypropylene is widely used for production of disposable syringes and for some other single use medical products. Under irradiation the yield of scission is significantly greater than the yield of crosslinking, resulting in a deterioration of mechanical properties. In addition a slow process of chain autooxidative degradation, following irradiation, usually takes place.

Two commercial resins and an additive-free isotactic polypropylene were used for studies in this work. The molecular weight distribution has been measured by high pressure, high temperature liquid chromatography, in order to determine the immediate effect of radiation degradation. This was accompanied by the melt viscosity measurements.

These data may be useful to predict the short and long term mechanical properties of polypropylene made products, sterilized by ionizing radiation.     

Polymerization and depolymerization by ultrasound

Ultrasound has been reported to cause both initiation of polymerization and depolymerization. The effects of the rate of flow of argon gas through styrene during exposure to ultrasound on the polymerization rate and the molecular weight distribution of the polymer formed were investigated. The results indicate that initiation of polymerization occurs primarily only when there is sufficient gas present to form a field of bubbles undergoing stable cavitation. With no gas present, transient cavitation occurs, resulting in depolymerization and the formation of coloured compounds similar to pyrolysis reaction products. These observations explain discrepancies in the sonochemistry literature.     

优化条件下过氧化氢降解壳聚糖的光谱学研究

在最佳反应条件下制备过氧化氢对壳聚糖的降解产物,通过测定原料及降解产物(Mw=1 500～166.53 kDa)的氮、碳含量,分析它们的红外光谱、核磁共振碳谱、X射线衍射谱及圆二色谱,考察各产物是否保持其天然结构。结果表明：各降解产物与原料的碳含量,氮含量及脱乙酰度的最大相对偏差分别为2.4%,2.3%与6.9%,且后两者随着反应时间的延长而减小;各降解样品的红外光谱及核磁共振碳谱与原料壳聚糖的相似,说明降解过程几乎不改变原料的化学结构;经相同方法处理过的原料及降解产物在2θ=10.4°和19.8°处均存在X射线衍射峰,在210 nm处均存在一个负的圆二吸收峰,表明产物的固态结构与其在溶液中的构象均没有发生变化。说明在优化的降解条件下过氧化氢氧化降解没有改变壳聚糖的天然结构。     

Ultrasonic depolymerization of aqueous polyvinyl alcohol.

Ultrasonication has proved to be a highly advantageous method for depolymerizing macromolecules because it reduces their molecular weight simply by splitting the most susceptible chemical bond without causing any changes in the chemical nature of the polymer. Most of the effects involved in controlling molecular weight can be attributed to the large shear gradients and shock waves generated around collapsing cavitation bubbles. In general, for any polymer degradation process to become acceptable to industry, it is necessary to be able to specify the sonication conditions which lead to a particular relative molar mass distribution. This necessitates the identification of the appropriate irradiation power, temperature, concentration and irradiation time. According to the results of this study the reactors constructed worked well in depolymerization and it was possible to degrade aqueous polyvinyl alcohol (PVA) polymer with ultrasound. The most extensive degradation took place at the lowest frequency used in this study, i.e. 23 kHz, when the input power was above the cavitation threshold and at the lowest test concentration of PVA, i.e. 1% (w/w). Thus this study confirms the general assumption that the shear forces generated by the rapid motion of the solvent following cavitational collapse are responsible for the breakage of the chemical bonds within the polymer. The effect of polymer concentration can be interpreted in terms of the increase in viscosity with concentration, causing the molecules to become less mobile in solution and the velocity gradients around the collapsing bubbles to therefore become smaller.     

Decolourization of Rhodamine B: A swirling jet-induced cavitation combined with NaOCl

A hydrodynamic cavitation reactor (Ecowirl) based on swirling jet-induced cavitation has been used in order to allow the degradation of a waste dye aqueous solution (Rhodamine B, RhB). Cavitation generated by Ecowirl reactor was directly compared with cavitation generated by using multiple hole orifice plates. The effects of operating conditions and parameters such as pressure, pH of dye solution, initial concentration of RhB and geometry of the cavitating devices on the degradation rate of RhB were discussed. In similar operative conditions, higher extents of degradation (ED) were obtained using Ecowirl reactor rather than orifice plate. An increase in the ED from 8.6% to 14.7% was observed moving from hole orifice plates to Ecowirl reactor. Intensification in ED of RhB by using hydrodynamic cavitation in presence of NaOCl as additive has been studied. It was found that the decolourization was most efficient for the combination of hydrodynamic cavitation and chemical oxidation as compared to chemical oxidation and hydrodynamic cavitation alone. The value of ED of 83.4% was reached in 37 min using Ecowirl combined with NaOCl (4.0 mg L⁻¹) as compared to the 100 min needed by only mixing NaOCl at the same concentration. At last, the energetic consumptions of the cavitation devices have been evaluated. Increasing the ED and reducing the treatment time, Ecowirl reactor resulted to be more energy efficient as compared to hole orifice plates, Venturi and other swirling jet-induced cavitation devices, as reported in literature.     

Degradation of diclofenac sodium using combined processes based on hydrodynamic cavitation and heterogeneous photocatalysis

Diclofenac sodium, a widely detected pharmaceutical drug in wastewater samples, has been selected as a model pollutant for degradation using novel combined approach of hydrodynamic cavitation and heterogeneous photocatalysis. A slit venturi has been used as cavitating device in the hydrodynamic cavitation reactor. The effect of various operating parameters such as inlet fluid pressure (2–4 bar) and initial pH of the solution (4–7.5) on the extent of degradation have been studied. The maximum extent of degradation of diclofenac sodium was obtained at inlet fluid pressure of 3 bar and initial pH as 4 using hydrodynamic cavitation alone. The loadings of TiO₂ and H₂O₂ have been optimised to maximise the extent of degradation of diclofenac sodium. Kinetic study revealed that the degradation of diclofenac sodium fitted first order kinetics over the selected range of operating protocols. It has been observed that combination of hydrodynamic cavitation with UV, UV/TiO₂ and UV/TiO₂/H₂O₂ results in enhanced extents of degradation as compared to the individual schemes. The maximum extent of degradation as 95% with 76% reduction in TOC has been observed using hydrodynamic cavitation in conjunction with UV/TiO₂/H₂O₂ under the optimised operating conditions. The diclofenac sodium degradation byproducts have been identified using LC/MS analysis.     

Use of hydrodynamic cavitation in (waste)water treatment

The use of acoustic cavitation for water and wastewater treatment (cleaning) is a well known procedure. Yet, the use of hydrodynamic cavitation as a sole technique or in combination with other techniques such as ultrasound has only recently been suggested and employed.In the first part of this paper a general overview of techniques that employ hydrodynamic cavitation for cleaning of water and wastewater is presented.In the second part of the paper the focus is on our own most recent work using hydrodynamic cavitation for removal of pharmaceuticals (clofibric acid, ibuprofen, ketoprofen, naproxen, diclofenac, carbamazepine), toxic cyanobacteria (Microcystis aeruginosa), green microalgae (Chlorella vulgaris), bacteria (Legionella pneumophila) and viruses (Rotavirus) from water and wastewater.As will be shown, hydrodynamic cavitation, like acoustic, can manifest itself in many different forms each having its own distinctive properties and mechanisms. This was until now neglected, which eventually led to poor performance of the technique. We will show that a different type of hydrodynamic cavitation (different removal mechanism) is required for successful removal of different pollutants.The path to use hydrodynamic cavitation as a routine water cleaning method is still long, but recent results have already shown great potential for optimisation, which could lead to a low energy tool for water and wastewater cleaning.     

Wastewater treatment: a novel energy efficient hydrodynamic cavitational technique

A novel method of treating a dye solution has been studied by hydrodynamic cavitation using multiple hole orifice plates. The present work deals with the effect of geometry of the multiple hole orifice plates on the degradation of a cationic dye rhodamine B (rhB) solution. The efficiency of this technique has been compared with the cavitation generated by ultrasound and it has been found that there is substantial enhancement in the extent of degradation of this dye solution using hydrodynamic cavitation. Large-scale operation coupled with better energy efficiency makes this technique a viable alternative for conventional cavitational reactors.     

Mechanochemical degradation kinetics of high-density polyethylene melt and its mechanism in the presence of ultrasonic irradiation

In this paper, the effect of ultrasonic intensity on the degradation of high-density polyethylene (HDPE) melt, degradation mechanism, ultrasonic degradation kinetics of HDPE melt as well as the development of molecular weight distribution of HDPE melt during ultrasonic degradation were studied. In the initial stage, the ultrasonic degradation of HDPE melt shows a random scission process, and the molecular weight distribution broadens. After that, the ultrasonic degradation of HDPE melt shows a nonrandom scission process, and the molecular weight distribution of HDPE melt narrows with ultrasonic irradiation time. The average molecular weight of HDPE decreases with the increase of ultrasonic intensity and increases and trends forward that of undegraded HDPE with the increase of distance from ultrasonic probe tip, indicating that attenuation of ultrasonic intensity in HDPE melt is very quick. Ultrasonic degradation kinetics of HDPE melt obeys the equation: Mt=M(infinity) + Ae(-kt). The theoretic calculation by this equation accords well with the experimental results. The plausible ultrasonic degradation mechanism of polymer melt based on molecular relaxation was also proposed in this paper.     

Hydrodynamic cavitation for sonochemical effects

A comparative study of hydrodynamic and acoustic cavitation has been made on the basis of numerical solutions of the Rayleigh-Plesset equation. The bubble/cavity behaviour has been studied under both acoustic and hydrodynamic cavitation conditions. The effect of varying pressure fields on the collapse of the cavity (sinusoidal for acoustic and linear for hydrodynamic) and also on the latter's dynamic behaviour has been studied. The variations of parameters such as initial cavity size, intensity of the acoustic field and irradiation frequency in the case of acoustic cavitation, and initial cavity size, final recovery pressure and time for pressure recovery in the case of hydrodynamic cavitation, have been found to have significant effects on cavity/bubble dynamics. The simulations reveal that the bubble/cavity collapsing behaviour in the case of hydrodynamic cavitation is accompanied by a large number of pressure pulses of relatively smaller magnitude, compared with just one or two pulses under acoustic cavitation. It has been shown that hydrodynamic cavitation offers greater control over operating parameters and the resultant cavitation intensity. Finally, a brief summary of the experimental results on the oxidation of aqueous KI solution with a hydrodynamic cavitation set-up is given which supports the conclusion of this numerical study. The methodology presented allows one to manipulate and optimise of specific process, either physical or chemical.     

水中自然超空泡机理及减阻效应的非平衡分子动力学研究

应用非平衡分子动力学方法,对水中超空泡流形成机理及减阻效应进行了模拟研究.计算得到了流体密度分布、局部空化数分布、阻力系数及含气百分比等流场细节数据,结果显示空化数判据在分子层面仍然成立,局部低空化数区域与超空泡形成区域在空间上分离;超空泡形成和稳定主要受物体运动速度影响;空化器构型对空泡内含气率有较大影响;从云雾空化状态过渡到超空泡,物体表面摩擦力可以减小50%—90%.与数值模拟结果的对比表明非平衡分子动力学模拟适用于研究微观超空泡机理,能够经济有效地探讨超高速流体运动的一些自然规律. 关键词： 非平衡分子动力学 超空泡 高速流体 摩擦系数     

Treatment of cyanide containing wastewater using cavitation based approach

Industrial wastewater streams containing high concentrations of biorefractory materials like cyanides should ideally be treated at source. In the present work, degradation of potassium ferrocyanide (K₄F_e(CN)₆) as a model pollutant has been investigated using cavitational reactors with possible intensification studies using different approaches. Effect of different operating parameters such as initial concentration, temperature and pH on the extent of degradation using acoustic cavitation has been investigated. For the case of hydrodynamic cavitation, flow characteristics of cavitating device (venturi) have been established initially followed by the effect of inlet pressure and pH on the extent of degradation. Under the optimized set of operating parameters, the addition of hydrogen peroxide (ratio of K₄F_e(CN)₆:H₂O₂ varied from 1:1 to 1:30 mol basis) as process intensifying approach has been investigated. The present work has conclusively established that under the set of optimized operating parameters, cavitation can be effectively used for degradation of potassium ferrocyanide. The comparative study of hydrodynamic cavitation and acoustic cavitation suggested that hydrodynamic cavitation is more energy efficient and gives higher degradation as compared to acoustic cavitation for equivalent power/energy dissipation. The present work is the first one to report comparison of cavitation based treatment schemes for degradation of cyanide containing wastewaters.     

Degradation of dichlorvos using hydrodynamic cavitation based treatment strategies

The degradation of an aqueous solution of dichlorvos, a commonly used pesticide in India, has been systematically investigated using hydrodynamic cavitation reactor. All the experiments have been carried out using a 20 ppm solution of commercially available dichlorvos. The effect of important operating parameters such as inlet pressure (over a range 3-6 bar), temperature (31 °C, 36 °C and 39 °C) and pH (natural pH = 5.7 and acidic pH = 3) on the extent of degradation has been investigated initially. It has been observed that an optimum value of pressure gives maximum degradation whereas low temperature and pH of 3 are favorable. Intensification studies have been carried out using different additives such as hydrogen peroxide, carbon tetrachloride, and Fenton’s reagent. Use of hydrogen peroxide and carbon tetrachloride resulted in the enhancement of the extent of degradation at optimized conditions but significant enhancement was obtained with the combined use of hydrodynamic cavitation and Fenton’s chemistry. The maximum extent of degradation as obtained by using a combination of hydrodynamic cavitation and Fenton’s chemistry was 91.5% in 1 h of treatment time. The present work has conclusively established that hydrodynamic cavitation in combination with Fenton’s chemistry can be effectively used for the degradation of dichlorvos.     

Effect of compressive stress on cavitation erosion-corrosion behavior of nickel-aluminum bronze alloy

The effect of compressive stress on cavitation erosion-corrosion behavior of nickel-aluminum bronze alloy was investigated, and the results showed that the alloy exhibited selective phase corrosion of eutectoid “α + κ_iii” and its destruction was aggravated with more cavitation mass loss up to 1.74 times of the specimen without stress. It was mainly owing to the enhanced corrosion-induced erosion caused by compressive stress, which led to lattice distortion of the alloy and the resulting accelerated selective phase corrosion with increasing surface roughness, and then intensified the synergistic effect of electrochemical corrosion and mechanical erosion.     

Cavitation characteristics analysis of a novel rotor-radial groove hydrodynamic cavitation reactor

Hydrodynamic cavitation was widely used in sterilization, emulsion preparation and other industrial fields. Cavitation intensity is the key performance index of hydrodynamic cavitation reactor. In this study, a novel rotor-radial groove (RRG) hydrodynamic cavitation reactor was proposed with good cavitation intensity and energy utilization. The cavitation performances of RRG hydrodynamic cavitation reactor was analyzed by utilizing computational fluid dynamics method. The cavitation intensity and the cavitation energy efficiency were used as evaluation indicators for RRG hydrodynamic cavitation reactor with different internal structures. The amount of generated cavitation for various shapes of the CGU, interaction distances and rotor speed were analyzed. The evolution cycle of cavitation morphology is periodicity (0.46 ms) in the CGU of RRG hydrodynamic cavitation reactor. The main cavitation regions of CGU were the outflow and inflow separation zones. The cavitation performance of rectangular-shaped CGU was better than the cylindrical-shaped CGU. In addition, the cavitation performance could be improved more effectively by increasing the rotor speed and decreasing the interaction distance. The research results could provide theoretical support for the research of cavitation mechanism of cavitation equipment.     

Dependence of cavitation,chemical effect,and mechanical effect thresholds on ultrasonic frequency

Cavitation, chemical effect, and mechanical effect thresholds were investigated in wide frequency ranges from 22 to 4880 kHz. Each threshold was measured in terms of sound pressure at fundamental frequency. Broadband noise emitted from acoustic cavitation bubbles was detected by a hydrophone to determine the cavitation threshold. Potassium iodide oxidation caused by acoustic cavitation was used to quantify the chemical effect threshold. The ultrasonic erosion of aluminum foil was conducted to estimate the mechanical effect threshold. The cavitation, chemical effect, and mechanical effect thresholds increased with increasing frequency. The chemical effect threshold was close to the cavitation threshold for all frequencies. At low frequency below 98 kHz, the mechanical effect threshold was nearly equal to the cavitation threshold. However, the mechanical effect threshold was greatly higher than the cavitation threshold at high frequency. In addition, the thresholds of the second harmonic and the first ultraharmonic signals were measured to detect bubble occurrence. The threshold of the second harmonic approximated to the cavitation threshold below 1000 kHz. On the other hand, the threshold of the first ultraharmonic was higher than the cavitation threshold below 98 kHz and near to the cavitation threshold at high frequency.