Preparation and characterization of TiO<Subscript>2</Subscript> sol–gel modified nanocomposite films

In this study, the role of TiO₂ MT-150A loading in the polymeric sol was investigated for the synthesis of immobilized TiO₂ nanocomposite films on glass substrate using the MT-150A nanoparticles-modified sol–gel method. The nanocomposite film properties were examined using different material characterization techniques including X-ray diffraction, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, UV–Vis spectrophotometer, Scotch tape test and pencil hardness test. The hydrophilicity of films during UV/Vis irradiation and storage in a dark place were evaluated by a contact angle analyzer. The MT-150A loading had a significant effect on the amount of crystallite phases in the films. However, increasing the MT-150A loading in the sol resulted in an increase in rutile phase content. In addition, increasing MT-150A loading in the sol yielded films with higher hydrophilicity but a concentration of 10–30 g/L MT-150A in the sol was found as the maximum for obtaining films with good adherence on the glass substrate.     

Synthesis and characterization of novel InVO<Subscript>4</Subscript>–TiO<Subscript>2</Subscript> thin films using the low temperature sol

The InVO₄ sol was obtained by a mild hydrothermal treatment (the precursor precipitation solution at 423 K, for 4 h). Novel visible-light activated photocatalytic InVO₄–TiO₂ thin films were synthesized through a sol–gel dipping method from the composite sol, which was obtained by mixing the low temperature InVO₄ sol and TiO₂ sol. The photocatalytic activities of the new InVO₄–TiO₂ thin films under visible light irradiation were investigated by the photocatalytic discoloration of methyl orange aqueous solution. The thin films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and UV–Vis absorption spectroscopy (UV–Vis). The results revealed that the InVO₄ doped thin films enhanced the methyl orange degradation rate under visible light irradiation, 3.0 wt% InVO₄–TiO₂ thin films reaching 80.1% after irradiated for 15 h.     

PMMA-SiO<Subscript>2</Subscript> organic–inorganic hybrid films: determination of dielectric characteristics

Organic–inorganic hybrid thin films have been prepared by a modified sol–gel route using tetraethyl orthosilicate as the inorganic (silica) source, methyl methacrylate (MMA) as the organic source, and 3-trimetoxysilylpropyl methacrylate as the coupling agent. The films were prepared by spin coating on Si (100) p-type substrates and subsequently heat-treated at 90 °C. Fourier transform infrared results reveal a set of absorption bands associated with the formation of both PMMA and SiO₂ phases in the hybrid films. Capacitance–voltage (C–V) characterization was carried out on metal-insulator-metal (MIM) and metal-insulator-semiconductor (MIS) structures, with the hybrid films as the insulator layer to evaluate the electrical properties. We present a detailed comparative analysis of the dielectric constant obtained from C–V characterization in the frequency range of 1 kHz–1 MHz. For the PMMA-SiO₂ hybrid material the dielectric constant values obtained were around 9.5 at 1 MHz which is superior to the values reported for thermally grown SiO₂ and pure PMMA materials. The interface state density for PMMA-SiO₂ on Si was approximately 10¹⁰ cm⁻², which is comparable to the standard SiO₂/Si structures. Due to the electrical behavior and low processing temperatures this hybrid dielectric is a very promising candidate for flexible electronic devices and its subsequent implementation does not require complex equipment.     

Preparation and characterization of In<Subscript>2</Subscript>S<Subscript>3</Subscript> semiconductor thin films using the sol–gel method

This study describes the In₂S₃ semiconductor thin film coating on glass substrate by sol–gel method. The In₂S₃ thin film samples were prepared and examined by the X-ray diffraction (XRD), the UV–visible optical absorption and transmission study, and the Scanning Electron Microscope (SEM) image analyses. The XRD analysis results show that the In₂S₃ semiconductor thin films prepared by sol–gel method is formed at T~360–520 °C temperature interval. Band gap energy and optical absorption spectrum analysis of the In₂S₃ thin films reveal that Eg~2.51 eV for the In₂S₃ thin films. According to the EDX result the film was In-rich with the In/S = 1.42 ratio. The thickness of prepared In₂S₃ layer is about 400 nm.     

Characterization of TiO<Subscript>2</Subscript> powders and thin films prepared by non-aqueous sol–gel techniques

Stable TiO₂ sols were prepared using two non-aqueous sol–gel processes with titanium n-butoxide and titanium isopropoxide, respectively. Crystallization and phase transitions of powders and thin films were studied by ex situ and in situ X-ray diffraction. For both methods, TiO₂ began to crystallize around 320 °C in air. Using helium instead of air during heat treatment slowed down the crystallization and substoichiometric powders were formed. TiO₂ thin films were obtained by spin coating. The morphology of the films was evaluated using scanning electron microscopy. The films were homogeneous and transparent in the visible range. The effect of the heating atmosphere and the type of substrate was investigated.     

Preparation of Ga<Subscript>2</Subscript>Se<Subscript>3</Subscript> thin films by sol–gel technique

In this study we describe the preparation of Ga₂Se₃ semiconductor compound thin films by sol–gel method for different crystal formation temperatures. The films were characterized by X-ray diffraction analyses (XRD), UV–visible spectrometer, and scanning electron microscope (SEM). The XRD spectrum showed that the formation of Ga₂Se₃ crystals were between 743 and 823 K. The thin film crystals that were formed at 773 K corresponded to the β phase and the preferred crystal structure was monoclinic. The value of band gap from optical absorption spectra for the Ga₂Se₃ thin films was estimated to be about E _g ~ 2.56 eV. The thickness of the one-coat Ga₂Se₃ thin films, which was measured by a Spectroscopic Ellipsometer, was about ~200 nm. The average grain sizes of scattered particles were within the limits between 200 and 500 nm.     

Preparation of highly stable TiO<Subscript>2</Subscript> sols and nanocrystalline TiO<Subscript>2</Subscript> films via a low temperature sol–gel route

Highly stable TiO₂ sols were prepared by adjusting the water-to-titanium molar ratio to ~4 in the process of hydrolysis and condensation of titanium isopropoxide in ethanol with HNO₃. Particularly, long-term stable TiO₂ sols were prepared without adding any chemical additives. Anatase TiO₂ nanocrystallites with sizes of 3–5 nm in diameter were uniformly dispersed in the stable sol. Crystallized TiO₂ films were successfully deposited on Si (100) using the stable sol via a dip-coating process with low temperature curing at as low as 100 °C. The synthesized TiO₂ sols and films are promising for use in flexible or dye-sensitized solar cells.     

Synthesis,characterization and performance of nanosized Bi<Subscript>0.1</Subscript>Sn<Subscript>0.9</Subscript>O<Subscript>2</Subscript>–WPU organic–inorganic hybrid coatings

A series of organic–inorganic hybrid coatings consisting of organic waterborne polyurethane (WPU) and inorganic nanosized bismuth-doped tin dioxide were successfully synthesized by the in situ polymerization approach. Bi_0.1Sn_0.9O₂ nano-powders were prepared via a new route of sol–gel combustion hybrid method using acetylene black as the fuel. The formed nano-powders were characterized by transmission electron microscopy and X-ray diffraction (XRD). Bi_0.1Sn_0.9O₂–WPU was then fabricated with isophorone diisocyanate, 2,2-bis(hydroxymethyl) propionic acid and nano-Bi_0.1Sn_0.9O₂-poly(ε-caprolactone) (PCL) as the starting materials. Organic–inorganic hybrid coatings are always achieved with adjustable contents of Bi_0.1Sn_0.9O₂. The hybrid coatings with Bi_0.1Sn_0.9O₂ loading on the glass substrate exhibited good heat insulation efficiency. The tensile strength and breaking extensibility of nanocomposite film containing 1.0% of the nano-Bi_0.1Sn_0.9O₂ were measured as 9.35 MPa and 248%, respectively. The transmittance of visible light was above 80%. The heat insulation of glass coated with nano-Bi_0.1Sn_0.9O₂–WPU hybrid was over 60 °C in contrast to the commercial blank glass.     

Preparation of LiCoPO<Subscript>4</Subscript> powders and films via sol–gel

Lithium intercalation materials are of special interest as cathodes in rechargeable batteries. An uncomplicated sol–gel process has been used for the synthesis of Li–Co phosphates powders and, for the first time, of LiCoPO₄ films. The powders were prepared from aqueous solutions, containing Li, Co and phosphate precursors to which acid citric and ethylene glycol was added, during the drying process at 75 °C. The X-ray diffraction patterns of the prepared powders confirmed the presence of LiCoPO₄ with an olivine-like structure as main phase. The morphological investigations of the powder showed a platelet-like structure with an average grain size of 0.75 μm. The films of LiCoPO₄ were deposited onto ITO glass substrates with the combination of the dip-coating process under the same conditions. Finally, the films were annealed in inert atmosphere at 300 °C. The morphological investigations reveal a smooth and homogeneous surface of the prepared Li–Co phosphate films. The preliminary electrical investigation on the prepared LiCoPO₄ films showed lithium ions electrochemical activity in the range 3.0–4.5 V.     

Preparation of CuAlO<Subscript>2</Subscript> thin films with high transparency and low resistivity using sol–gel method

CuAlO₂ thin films were deposited on quartz substrates by sol–gel process using copper acetate monohydrate and aluminum nitrate nanohydrate as starting materials and isopropyl alcohol as solvent. The influence of annealing temperature on the film structure and the phase evolution of CuAlO₂ films were investigated, so as to obtain CuAlO₂ films with superior performance. The phase compositions of the films were dependent on the annealing temperature. The films annealed at temperatures below 400 °C were amorphous while those annealed above 400 °C were polycrystalline. The phases of CuO and CuAl₂O₄ appeared gradually with the increase of annealing temperature. When the heat treatment temperature was elevated to 900 °C, the uniform and dense films with single phase of CuAlO₂ were obtained, with a resistivity of 15 Ωcm. The transmittance of the 310 nm-thick CuAlO₂ film is 79% at 780 nm and the direct optical band gap is 3.43 eV.     

Bandgap modification of TiO<Subscript>2</Subscript> sol–gel films by Fe and Ni doping

Nickle and iron doped TiO₂ thin films were prepared on glass substrates by sol–gel dip coating process. Indirect and direct optical energy gaps were calculated with the incorporation of different concentrations of both the ions. Indirect bandgap was found to be a strong function of the dopant concentration, whereas direct energy gap has negligible dependence on the nature of dopant and its concentration. Direct energy gap has always been found to retain a value higher than the indirect energy gap. Variation of observed energy gap properties shows a trend similar to that reported on the basis of numerical calculations or the samples obtained by other techniques. Increase in refractive index and corresponding density of the film sample does not support the change in turn over frequency. The influence of crystalline phase change is also ruled out by XRD investigations. It is concluded that red shift of band edge absorption takes place by incorporation of dopant and sol–gel dip coating technique offers an effective low cost route to the production of these coatings.     

Photoelectrochemical performance of bilayered Fe–TiO<Subscript>2</Subscript>/Zn–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> thin films for solar generation of hydrogen

A visible-light sensitive bilayered photoanode of Fe–TiO₂/Zn–Fe₂O₃ has been developed by spray pyrolytically depositing Zn–Fe₂O₃ layers onto predeposited Fe–TiO₂ thin film on ITO substrate. Fe–TiO₂/Zn–Fe₂O₃ photoelectrodes were characterized by XRD, Raman, AFM, UV-vis absorption spectroscopy. Photoelectrochemical properties of bilayered Fe–TiO₂/Zn–Fe₂O₃ photoelectrode were studied by Mott–Schottky curves and I–V characteristics. Bilayered Fe–TiO₂/Zn–Fe₂O₃ photoelectrode was observed to possess much higher separation efficiency of photogenerated charge carriers and could generate nine times better photocurrent density than pure Fe–TiO₂. Solar to hydrogen conversion efficiency exhibited by this electrode was 0.77%.     

Preparation and characterization of ZnTiO<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>/pillared montmorillonite composite catalyst for enhanced photocatalytic activity

ZnTiO₃–TiO₂/organic pillared montmorillonite (pMt) composite catalyst was successfully prepared in this paper by immobilizing ZnTiO₃–TiO₂ onto pMt. The composition and texture of the prepared composite catalyst were characterized by X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, transmission electron microscopy, energy dispersive spectrometry, ultraviolet–visible light (UV–Vis) diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The photocatalytic activity was tested via photocatalytic degradation of methyl blue (MB) under both visible irradiation and UV light. The results indicated that the ZnTiO₃–TiO₂/pMt composite catalyst had an apparent absorption at the area of visible irradiation, and exhibited a higher efficiency of photocatalytic degredation of MB under visible irradiation. This was due to the heterostructure of ZnTiO₃–TiO₂, and the mesoporous structure and specific surface area of the ZnTiO₃–TiO₂/pMt composite. In addition, the results of the radical scavenging experiments showed that the holes and superoxide radicals are responsible for the degradation of MB under visible irradiation.     

Correlation between structural and optical properties of TiO<Subscript>2</Subscript>:ZnO thin films prepared by sol–gel method

We have studied structural and optical properties of thin films of TiO₂, doped with 5% ZnO and deposited on glass substrate (by the sol–gel method). Dip-coated thin films have been examined at different annealing temperatures (350–450 °C) and for various layer thicknesses (89–289 nm). Refractive index, porosity and energy band gap were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range of 1.97–2.44, the porosity is in the range of 0.07–0.46 and the energy band gap is in the range of 3.32–3.43. The coefficient of transmission varies from 50 to 90%. In the case of the powder of TiO₂, doped with 5% ZnO, and aged for 3 months in ambient temperature, we have noticed the formation of the anatase phase (tetragonal structure with 20.23 nm grains). However, the undoped TiO₂ exhibits an amorphous phase. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 350 °C. The obtained structures are anatase and brookite. The calculated grain size, depending on the annealing temperature and the layer thickness, is in the range of 8.61–29.48 nm.     

Particulate sol–gel synthesis and optical and electrical properties of CeO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> nanocomposite

CeO₂/TiO₂ nanocomposite was synthesized by particulate sol–gel method. The X-ray diffractogram shows the presence of cubic CeO₂ and anatase TiO₂ in the composite. The high resolution scanning electron micrographs reveal the nanoparticulate nature of the prepared composite. The composite absorbs UV light and exhibits near-band gap emission corresponding to TiO₂ and deep level emission due to crystal defects. The Nyquist plot displays two semicircular arcs indicating the material heterogeneity. The physicochemical characteristics of the synthesized nanocomposite are in favour of its application as an ingredient of sunscreen formulations; under UV light the photocatalytic activity of CeO₂/TiO₂ composite, tested through the degradation of rhodamine B, is very much less than that by pristine anatase TiO₂. Reduced adsorption of moisture by the nanocomposite is a possible reason for the observed very low photocatalytic activity.     

Novel sol–gel synthesis of transparent and electrically bistable LiNbO<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> nanocomposites thin films

The morphological and electrical characterization of transparent nanostructured LiNbO₃–SiO₂ thin films synthesized by a novel sol–gel route is reported. Films annealed at different temperatures exhibit different size of the nanocrystals, as demonstrated by Atomic Force Microscopy and Glancing Incidence X-ray diffraction. The dc electrical measurements performed on planar devices reveal electrical bistability. A clear relationship between the electrical bistability and the size of LiNbO₃ nanocrystals embedded in the matrix is observed.     

Preparation,dielectric and ferroelectric properties of (Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>)<Subscript>0.94</Subscript>Ba<Subscript>0.06</Subscript>TiO<Subscript>3</Subscript> thin films by a sol–gel process

(BiFeO₃)_1−x –(BaTiO₃) _x solid solution thin films are grown on Pt/Ti/SiO₂/Si substrates by chemical solution deposition method. Films with x = 0.00, 0.05 and 0.10 were prepared by annealing at 500°C. X-ray diffraction patterns indicate that the pure BiFeO₃ film adopts random orientation while the solid solution films are highly (100) preferentially oriented. Improved electric property at room temperature was observed in the BaTiO₃ incorporated BiFeO₃ films. The remanent polarization of the film with x = 0.0, 0.05 and 0.10 are 76.6, 51.9 and 19.7 μC/cm² respectively under a measuring electric field of 0.94 MV/cm. The BaTiO₃ incorporated BiFeO₃ films show improved fatigue endurance. By the solid solution with BaTiO₃, the leakage current density is reduced effectively.     

TiO<Subscript>2</Subscript> thin films on soda-lime and borosilicate glass prepared by sol–gel processing: influence of the substrates

TiO₂ films were deposited on soda-lime and borosilicate glass substrates, their optical and microstructural properties were investigated. X-ray diffraction showed significant differences between the sample series. Films deposited on the upper surface of soda-lime glass substrates showed higher indices of refraction than those prepared on the lower surface that had been in contact with the tin bath during float glass production. Results indicate that these differences not only result from different optical properties of the TiO₂ backbone material due to alkali contamination but that also different film porosities can measured by ellipsometric porosimetry.     

Growth and characterization of (K<Subscript>0.5</Subscript> Na<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript> thin films by a sol–gel method

(K_0.5 Na_0.5)NbO₃ (KNN) perovskite materials have been developed as a promising lead-free piezoelectric material for environmentally benign piezoelectric devices. KNN films with about 320 nm thickness were fabricated on Pt(111)/SiO₂/Si(100) substrates by a sol–gel method from stoichiometric and A-site ion excess precursor solutions. Two different annealing methods were also used to investigate the crystallographic evolution of the films. A layer-by-layer annealing process results in highly (001) oriented KNN from the annealing temperature of 550 °C, while the final annealing method leads to weaker crystalline peaks with a random orientation. The KNN films from the K and Na excess precursor solutions show similar crystallization behavior. However, the ferroelectric hysteresis loops of the films were greatly improved by compensating for an A-site vacancy. In particular, the KNN films from K-excess precursor solutions show better ferroelectric properties compared to the films prepared from Na excess solutions.     

Preparation and activity evaluation of relative p–n junction photocatalyst Co-TiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript>

Co-TiO₂ photocatalyst was prepared by a sol–gel method using Co(NO₃)₂ · 6H₂O and tetrabutyl titanate [Ti(OC₄H₉)₄] as raw materials, and Co-TiO₂/TiO₂ photocatalyst was synthesized by mixing the Co-TiO₂ sol with TiO₂ sol. The Co-TiO₂/TiO₂ was characterized by X-ray powder diffraction, UV–Vis diffuse reflection spectrum, scanning electron microscopy, transmission electron microscopy, fluorescence spectra and X-ray photoelectron spectroscopy. The photocatalytic activity of the photocatalyst was evaluated by photocatalytic reduction of Cr₂O₇ ²⁻ and photocatalytic oxidation of methyl orange under UV irradiation. The results showed that, for the photocatalytic reduction of Cr₂O₇ ²⁻, the optimum percentage of Co-doped for the Co-TiO₂ was 0.5% (mole ratio of Co/Ti), and the optimum percentage of Co-TiO₂ for the Co-TiO₂/TiO₂ was 2.0% (mole ratio of Co-TiO₂/TiO₂). The photocatalytic reduction activities of the Co-TiO₂/TiO₂ and Co-TiO₂ are much higher than that of TiO₂. However, the photocatalytic oxidation activities of the Co-TiO₂/TiO₂ and Co-TiO₂ are much lower than that of TiO₂. Effects of heat treatment on the photocatalytic activities of the Co-TiO₂/TiO₂ and Co-TiO₂ were investigated. The mechanisms of influence on the photocatalytic activity were also discussed.