C-Nb共掺杂SnO_2电子结构的第一性原理研究

本文利用第一性原理研究了C-Nb共掺杂的SnO_2稳定性、能带结构与态密度,从自旋向上和自旋向下的能带结构以及态密度分析了掺杂体系磁性产生的机理.研究结果表明,C-Nb共掺杂SnO_2体系的稳定性强于C,Nb单掺杂SnO_2体系;C,Nb单掺杂、C-Nb共掺杂的SnO_2体系的总磁矩分别为0μB、0.922μB、1.0μB;Nb掺杂SnO_2体系产生磁性在于Nb的d轨道引入,C-Nb共掺杂SnO_2体系产生磁性在于Nb的s轨道和C的p轨道相互作用.     

Mg2Si:Fe 电子结构及磁性的理论研究

采用基于密度泛函理论的第一性原理赝势平面波方法研究了Mg_2Si:Fe体系的电子能带结构、态密度和磁性.结果表明:掺入的Fe原子优先占据晶格中的空隙位,也可能代替晶格中的Mg位.从能带结构和态密度可以看出,当Fe原子位于晶格中空隙位时,系统显示出金属性;当Fe占据Mg位置时,对于自旋向上电子态,体系有一带隙存在,系统呈现明显的半导体特性;对于自旋向下电子态,Fe的替位掺杂在该体系内引入新的杂质能级,杂质能级与导带价带分离,且100%自旋极化.两种位置的杂质,上自旋电子和下自旋电子的态密度均明显不对称,诱导出铁磁性,且铁磁性主要由于Fe的3d态电子诱导产生.Fe位于空隙位时,Fe原子的磁矩为1.69μB;Fe占据Mg位时,Fe原子的磁矩为1.38μB,说明原子磁矩与其所占位置和配位情况有关.     

第一主族元素(Li,Na,K)和第二主族元素(Be,Mg,Ca)掺杂二维六方氮化硼单层的第一性原理计算研究

采用基于密度泛函理论的第一性原理计算方法研究了第一、第二主族元素取代六方BN单层中的B的几何结构、磁性性质和电子结构.研究发现,掺杂的BN单层出现明显的自旋极化特性.对Li,Na,K而言,掺杂后超胞的总磁矩为2μB,对Mg,Ca而言,超胞的总磁矩为1μB,磁矩主要局域在与杂质原子最近邻的N原子上.而对于Be,超胞的总磁矩为0.705μB,磁矩分散在所有的N原子上.对于6种掺杂情况,给出了相应的自旋密度图.掺杂体系产生明显的杂质能级,给出了总态密度和局域投影态密度等结果,分析了杂质能级的产生.发现Mg和Ca掺杂体系的态密度具有明显的半金属特性.     

非金属N和过渡金属(Mo, Ru, Rh, Pd)掺杂SnO2磁性的第一性原理研究

本文基于第一性原理方法,对非金属元素(N)与过渡金属元素(Mo, Ru, Rh, Pd)掺杂SnO₂的电子结构和磁学性质进行计算分析.结果表明：形成能与过渡金属原子半径密切相关,随着过渡金属原子半径的增加,形成能在降低,其中N-Mo掺杂体系形成能最低,故该体系最容易掺杂形成;能带结构分析表明,由于掺杂体系自旋向上/向下杂质能级的数量和分布均不对称,掺杂体系均有磁性产生;进一步探究态密度可知,体系产生磁性的原因是过渡金属原子和N原子之间产生p-d轨道杂化,最外层电子轨道上的空位及单电子相互耦合所导致.结果表明,由于掺杂原子的引入,SnO₂体系产生磁性,并且掺杂体系呈现亚铁磁性,其中N-Rh掺杂体系的磁性最好,其磁矩为1.88μB,有望成为良好的稀磁半导体材料.     

过渡金属 X（ X=Cr、Mn、Fe、Tc、Re ）掺杂Janus Ga2SSe 的第一性原理研究

利用密度泛函理论的第一性原理赝势平面波方法,研究过渡金属X(X=Cr、Mn、Fe、Tc、Re)原子掺杂Janus Ga₂SSe的磁性、电子性质及光学性质.研究表明：过渡金属掺杂Janus Ga₂SSe体系在Chalcogen-rich条件下有着比Ga-rich条件下更好的稳定性.其中Mn掺杂体系形成能在两种条件下皆为最低.本征Ga₂SSe是具有2.02 eV带隙的间接带隙半导体,在紫外区域有着很好的光伏吸收能力.与本征Ga₂SSe相比,Cr掺杂体系自旋向上通道出现杂质能级,自旋向上与向下通道不对称,呈磁矩为2.797μ_B铁磁性半金属. Mn掺杂体系在其自旋向上通道产生的杂质能级,呈磁矩为3.645μ_B的磁性P型半导体. Fe掺杂体系自旋向下通道产生的杂质能级,呈磁矩为3.748μ_B磁性P型半导体.在Tc与Re掺杂后,带隙皆由间接变直接带隙,呈无磁性的P型半导体.从光学性质来看,各掺杂体系与未掺杂Ga₂SSe在介电...     

第一性原理研究In,N共掺杂SnO2材料的光电性质

采用全电势线性缀加平面波(FP-LAPW)的方法,基于密度泛函理论第一性原理结合广义梯度近似(GGA),运用Wien2k软件计算了In, N两种元素共掺杂SnO₂材料的电子态密度和光学性质. 研究表明,共掺杂结构在自旋向下和向上两方向上都出现细的局域能级,两者态密度分布不对称;带隙内自旋向下方向上产生局域能级,共掺化合物表现出半金属性;能带结构显示两种共掺杂化合物仍为直接禁带半导体,价带顶随着N浓度的增加发生向低能方向移动,带隙明显增宽;共掺下的介电函数虚部主介电峰只在8.58 eV 关键词： 电子结构 态密度 能带结构 光学性质     

Y,Zr,Nb掺杂SnO_2电子结构的第一性原理研究

本文基于第一性原理方法研究了Y,Zr,Nb在Sn位掺杂SnO_2的键长变化、稳定性、能带结构以及态密度.结果表明:Y,Zr,Nb在Sn位掺杂SnO_2使附近的键长发生改变,改变量最大是Y掺杂SnO_2体系;掺杂体系的杂质替换能都为负值,表明体系为稳定结构;掺杂使SnO_2能级增多,能较好的调节带隙值;而Y掺杂SnO_2体系价带顶端有一条能级越过了费米线表明该体系呈现出半导体的特征;同时,Y,Zr,Nb掺杂SnO_2使导带底端的能级出现分离;在低能区的态密度仍主要由Sn、O的s轨道贡献;在高能区态密度的掺杂体系出现sp杂化的现象; Zr掺杂SnO_2的态密度能量向低能区移动.     

碱土金属X（X=Be，Mg，Ca和Sr）掺杂二维SnS2材料的第一性原理研究

基于密度泛函理论的第一性原理研究赝势平面波方法,计算了碱土金属X(X=Be, Mg, Ca和Sr)掺杂二维单层SnS₂的电子结构、磁学性质和光学性质.结果表明：S-rich条件下的体系相较于Sn-rich更稳定,能带结构表明：在Be掺杂后,SnS₂体系从自旋向上通道和自旋向下通道完全对称的非磁性半导体转变为具有1.999μ_B磁矩的磁性半导体.在Mg掺杂后,体系转变为非磁性P型半导体;Ca和Sr两种掺杂体系由于极化程度的不同,导致在下自旋通道的能带穿过费米能级,而在上自旋通道的能带并未穿过费米能级,呈现出磁矩分别为1.973、2.000μ_B的半金属特性.同时发现X(X=Be, Mg, Ca和Sr)掺杂后,掺杂体系实部静态介电常数大幅度增加,掺杂后的SnS₂体系的极化能力增强,虚部数值在低能区明显变大,更适用于长波长光电器. Be, Mg, Ca和Sr掺杂不仅导致吸收边红移,而且提高了红外光区域的有效利用率.     

Half-Heusler合金NiFeSb和NiMnSb的磁性及电子结构的第一性原理研究

用基于密度泛函理论的第一性原理方法,计算了half-Heusler合金NiFeSb和NiMnSb的晶体结构、磁性及电子结构。计算结果表明,磁性原子Fe和Mn在两种合金的总磁矩中贡献最大,在NiFeSb总磁矩中,Ni原子贡献比例接近在NiMnSb中的2倍,而Sb原子的贡献比例是在NiMnSb中的1/5;两种合金的自旋向上能带都具有明显的金属特征,而自旋向下能带有明显的差别;两种合金费米能级以下的总态密度(DOS)主要由Ni-3d 和Fe-3d（Mn-3d）态决定,费米能级以上主要由Fe-3d（Mn-3d）自旋向下部分决定。     

过渡金属原子X(X=Mn,Tc,Re)掺杂二维WS2第一性原理研究

二维材料由于具有独特的电子结构和量子效应、丰富的可调控特性而受到凝聚态物理和材料科学的广泛关注,其中通过过渡金属掺杂二维WS2形成的半金属铁磁性材料在自旋电子学领域中发挥着重要的作用.采用基于密度泛函理论的第一性原理赝势平面波方法计算了过渡金属原子X (X=Mn, Tc, Re)掺杂二维WS~2的电子结构、磁性和光学性质.研究表明:被过渡金属原子X掺杂的WS~2体系在S-rich条件下比在W-rich条件下更稳定.在Mn掺杂后,自旋向上通道中出现杂质能级,导致WS~2体系从自旋向上和自旋向下态密度完全对称的非磁性半导体转变为磁矩1.001μB的铁磁性半金属.在Tc, Re掺杂后,体系均转变为非磁性N型半导体.所有掺杂体系杂质态均发生自旋劈裂现象,且自旋劈裂程度逐渐减小.同时发现Mn, Tc, Re掺杂后,表现出优异的光学性质,它们的介电常数和折射系数与未掺杂WS~2的体系相比明显增强,吸收系数在低能量区域(0—2.0 eV)均出现红移现象.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.