Highly Active Nickel Nanoparticles Supported on TiO2 Nanotube Electrodes for Methanol Electrooxidation

Nickel nanoparticles/TiO₂ nanotubes/Ti electrodes were prepared by galvanic deposition of nickel nanoparticles on the TiO₂ nanotubes layer on titanium substrates. Titanium oxide nanotubes were fabricated by anodizing titanium foil in a DMSO fluoride‐containing electrolyte. The morphology and surface characteristics of titanium dioxide nanotubes and Ni/TiO₂/Ti electrodes were investigated using scanning electron microscopy and energy‐dispersive X‐ray spectroscopy, respectively. The results indicated that nickel nanoparticles were homogeneously deposited on the surface of TiO₂ nanotubes. The electrocatalytic behaviour of nickel nanoparticles/TiO₂/Ti electrodes for the methanol electrooxidation was studied by electrochemical impedance spectroscopy, cyclic voltammetry, differential pulse voltammetry and chronoamperometry methods. The results showed that Ni/TiO₂/Ti electrodes exhibit a considerably higher electrocatalytic activity toward the oxidation of methanol.     

Cobalt Single-Atom Reverse Hydrogen Spillover for Efficient Electrochemical Water Dissociation and Dechlorination

Efficient water dissociation to atomic hydrogen (H*) with restrained recombination of H* is crucial for improving the H* utilization for electrochemical dechlorination, but is currently limited by the lack of feasible electrodes. Herein, we developed a monolithic single-atom electrode with Co single atoms anchored on the inherent oxide layer of titanium foam (Co₁−TiO_x/Ti), which can efficiently dissociate water into H* and simultaneously inhibit the recombination of H*, by taking advantage of the single-atom reverse hydrogen spillover effect. Experimental and theoretical calculations demonstrated that H* could be rapidly generated on the oxide layer of titanium foam, and then overflowed to the adjacent Co single atom for the reductive dechlorination. Using chloramphenicol as a proof-of-concept verification, the resulting Co₁−TiO_x/Ti monolithic electrode exhibited an unprecedented performance with almost 100 % dechlorination at −1.0 V, far superior to that of traditional indirect reduction-driven commercial Pd/C (52 %) and direct reduction-driven Co₁−N−C (44 %). Moreover, its dechlorination rate constant of 1.64 h⁻¹ was 4.3 and 8.6 times more active than those of Pd/C (0.38 h⁻¹) and Co₁−N−C (0.19 h⁻¹), respectively. Our research sheds light on the rational design of hydrogen spillover-related electrocatalysts to simultaneously improve the H* generation, transfer, and utilization for environmental and energy applications.     

Electrochemical and XPS measurements on thin oxide films on zirconium

The potentiodynamic growth of thin oxide films on zirconium electrodes was investigated by coulometric and simultaneous impedance measurements, as a function of the electrode potential (0 V ⩽ E ⩽ 9 V), the pH (0 ⩽ pH ⩽ 14) and the surface preparation (electropolishing, etching and mechanical polishing). The initial film thickness d₀ is at least 4–6 nm; with increasing potential, the oxide grows irreversibly by 2.6 nm/V (pH 0.3) up to 3.2 nm/V (pH 14). In Cl⁻- and ClO⁻₄-containing solutions the oxide growth is limited by localized corrosion. The oxide behaves like a typical insulator with a donor concentration N_D < 10¹⁹ cm⁻³ and a dielectric constant D = 31. Below −0.5 V (vs. SHE) only, th film behaves like an n-type semiconductor with N_D ≈ 3 × 10¹⁹ cm⁻³. From photoelectrochemical measurements a direct and an indirect transition with band gap energies of E_g = 5 eV and E_g = 2.8 eV could be derived. Anodic electron-transfer reactions (ETRs) are blocked at the homogeneous oxide surface, but cathodic ETRs are possible at larger overvoltages. Near the flatband potential E_fb ≈ −1.3 ± 0.2 V (vs. SHE) hydrogen evolution takes place with a simultaneous increase of the capacity which may be attributed to hydrogen incorporation. With XPS measurements the stoichiometry of the oxide film was determined as ZrO₂ at all the pH values examined, but a thin outer layer contained some hydroxide. Components of the forming electrolyte could not be detected (sulphate, borate and perchlorate < 1%), but etching in HF caused accumulation of F⁻ at the inner boundary.     

Antimony Doped Tin Oxide Nanoparticles Deposited onto Nb−TiO2 Nanotubes for Electrochemical Degradation of Bio‐refractory Pollutions

To improve the service life of SnO₂?Sb electrodes in degradation of refractory wastewater, we report anodic information of tin oxide antimony on top of Nb?TiO₂ nanotubes (Nb?Ti/Nb?TiO₂?NTs/ATONPs) prepared through screen‐printing. It was found that the Nb?Ti/Nb?TiO₂?NTs/ATONPs anodes presented a significantly enhanced in electro‐catalytic oxidation performance (in Acid Red 73) compared to titanium‐based tin antimony electrodes (Ti/ATONPs). Additionally, the electrochemical properties and the stability were further studied by the electrochemical impedance spectroscopy (EIS), linear sweep voltammetry (LSV), cyclic voltammetry (CV), chronoamperometry (CA) measurements and accelerated life test, respectively. These results indicated that Nb?TiO₂?NTs/ATONPs anode possessed Nb?TiO₂ nanotubes which exhibited a higher oxygen evolution potential (2.24 V vs. Ag/AgCl), as well as a better wettability, a larger current at constant potential and 2.1 times longer lifetime than the conventional Ti/ATONPs anode.     

Gold particles supported on self-organized nanotubular TiO2 matrix as highly active catalysts for electrochemical oxidation of glucose

Au/TiO₂/Ti electrode was prepared by a two-step process of anodic oxidation of titanium followed by cathodic electrodeposition of gold on resulted TiO₂. The morphology and surface analysis of Au/TiO₂/Ti electrodes was investigated using scanning electron microscopy and EDAX, respectively. The results indicated that gold particles were homogeneously deposited on the surface of TiO₂ nanotubes. The nanotubular TiO₂ layers consist of individual tubes of about 60–90 nm in diameter, and the electrode surface was covered by gold particles with a diameter of about 100–200 nm which are distributed evenly on the titanium dioxide nanotubes. This nanotubular TiO₂ support provides a high surface area and therefore enhances the electrocatalytic activity of Au/TiO₂/Ti electrode. The electrocatalytic behavior of Au/TiO₂/Ti electrodes in the glucose electro-oxidation was studied by cyclic voltammetry. The results showed that Au/TiO₂/Ti electrodes exhibit a considerably higher electrocatalytic activity toward the glucose oxidation than that of gold electrode.     

Interlaced polyaniline/carbon nanotube nanocomposite co-electrodeposited on TiO<Subscript>2</Subscript> nanotubes/Ti for high-performance supercapacitors

A series of PANI-CNTs/TiO₂ nanotubes/Ti electrodes were fabricated via pulse current co-electrodeposition of polyaniline and functionalized carbon nanotubes onto TiO₂ nanotubes/Ti electrodes. FT-IR spectrometry, X-ray photoelectron spectroscopy, and scanning electron microscopy were applied in order to characterize the modified TiO₂ nanotubes/Ti electrodes. The morphology studies showed that the PANI-CNTs/TiO₂ nanotubes/Ti nanocomposite electrode has many interlaced PANI-CNTs nanorods on the surface of TiO₂ nanotubes. The electrochemical measurements of the modified electrodes confirmed that the CNTs in the composite can significantly improve the capacitive behavior as well which have been compared with that of PANI/TiO₂ nanotubes/Ti electrodes. The modified electrode exhibited much higher specific capacitance (190 mF cm^?2 with 90% retention after 1000 cycles) compared to the PANI/TiO₂ nanotubes/Ti (70 mF cm^?2 with 77% retention after 1000 cycles) at a current density of 0.85 mA cm^?2, indicating its great potential for supercapacitor applications.

Open image in new window

Graphical abstract Interlaced polyaniline/carbon nanotube nanocomposite electrodeposited on TiO₂ nanotubes/Ti

     

TiO<Subscript>2</Subscript> nanotube arrays based DSA electrode and application in treating dye wastewater

Dimensionally stable anode (DSA) of antimony-doped tin dioxide electrode based on TiO₂-nanotube arrays (NTs) has been successfully fabricated through thermal decomposition. The surface morphology and composition of the electrodes were characterized by using scanning electron microscopy and X-ray diffraction. Methyl orange (MO) was used as a model pollutant to investigate the electrochemical properties of these two electrodes. The optimized anodic oxidation voltage and time for TiO₂-nanotubes array based DSA electrode is 60 V and 10 min, respectively. The results show that Ti/TiO₂–NTs/Sb–SnO2 electrode has an increase of 100 mV in oxygen evolution overpotential and the service life is 56% longer than that of the traditional DSA electrode. Under the optimum conditions, MO solution decolorization rate and TOC removal rate reached approximately 100 and 80%, respectively. Study suggested that the as-prepared Ti/TiO₂–NTs/Sb–SnO2 DSA electrode exhibits high activity for degradation of organic pollutant with high concentration.     

ESR study on the visible photocatalytic mechanism of nitrogen-doped novel TiO2: Synergistic effect of two kinds of oxygen vacancies

The visible photocatalytic mechanism of nitrogen-doped novel TiO₂ was studied by means of electron spin resonance spectroscopy (ESR). It was found that, under visible light irradiation, the concentration of single-electron-trapped oxygen vacancy (SETOV, V_o^•) of novel TiO₂ remained unchanged, but that of nitrogen-doped novel TiO₂ increased and returned to original state when the light was turned off. This implies that, aside from V_o^• in bulk of nitrogen-doped novel TiO₂, oxygen vacancy without trapped electron (V_o^••) was formed on its surface. V_o^•• as a surface electron trap captured photogenerated electron from the bulk to generate extra V_o^•, carrying out photocatalytic reaction on the surface. At the same time, nitrogen doping product NO was chemically adsorbed on the vicinity of V_o^•• and inhibited the attack of oxygen, allowing V_o^•• to remain stable in air. The synergistic action of the two kinds of active structures, i.e., bulk V_o^•–NO–Ti and surface V_o^••–NO–Ti, accounted for the visible photocatalytic activity of N-doped novel TiO₂.     

Ti/TiO2 indicator electrodes formed by plasma electrolytic oxidation for potentiometric analysis

Ti/TiO₂ indicator electrodes were prepared by plasma electrolytic oxidation (PEO) method in the tetraborate electrolyte and were used for potentiometric indication of chemical reactions of different types and for analysis of surface and industrial wastewaters on the example of potentiometric determination of alkalinity and chloride. The electrodes formed at current densities of 0.05, 0.1, 0.15 and 0.2 A/cm² are different in composition, surface morphology and electroanalytical properties. The electrodes formed at a current density of 0.05 A/cm² exhibit the highest pH-sensitivity and generate the highest analytical signal at the equivalence point in the acid–base and precipitation titrations. The maximum analytical signal at the equivalence point, exceeding in magnitude the analytical signal, obtained by classical Pt electrode in oxidation–reduction and complexometric titrations generates PEO layers formed at a current density of 0.05 A/cm² and a platinum-modified nanoparticles. The results of the potentiometric titration of the surface and technogenic waters using as indicator Ti/TiO₂ electrodes are comparable with the conventionally used glass electrode (to determine alkalinity) and Ag electrode (to the determine chloride) and the results of visual titration. The advantage of the obtained metal oxide systems is the ability to determine two hydrochemical parameters due to their multifunctionality and opportunity to work with a single electrode. In addition, these sensors offer some analytical characteristics such as sensitivity, good reproducibility, high mechanical stability and a simple preparation procedure.     

A Glucose Biosensor Based on Immobilization of Glucose Oxidase into 3D Macroporous TiO2

3D macroporous TiO₂ inverse opals have been derived from a sol‐gel procedure using polystyrene colloidal crystals as templates. EDS and SEM showed a face‐centered cubic (FCC) structure TiO₂ inverse opal was obtained. Glucose oxidase (GOx) was successfully immobilized on the surface of indium‐tin oxide (ITO) electrode modified by TiO₂ inverse opal (TiO_2(IO)). Electrochemical properties of GOx/TiO_2(IO)/ITO electrode were characterized by using the three electrodes system. The result of cyclic voltammetry showed that a couple of stable and well‐defined redox peaks for the direct electron transfer of GOx in absence of glucose, and the redox peak height enhanced in presence of 0.1 μM glucose. Compare with the ordinary structured GOx/TiO₂/ITO electrode, inverse opal structured GOx/TiO_2(IO)/ITO electrode has a better respond to the glucose concentration change. Under optimized experimental conditions of solution pH 6.8 and detection potential at 0.30 V versus saturated calomel electrode (SCE), amperometric measurements were performed. The sensitivity and the detection limit of glucose detection was 151 μA cm^?2 mM^?1 and 0.02 μM at a signal‐to‐noise ratio of 3, respectively. The good response was due to the good biocompatibility of TiO₂ and the large effective surface of the three‐dimensionally ordered macroporous structure.     

Highly-ordered dye-sensitized TiO2 nanotube arrays film used for improving photoelectrochemical electrodes

Thin titanium oxide nanotube arrays (TNAs) films were synthesized by anodization of titanium foil in an aqueous dimethyl sulfoxide solution using a platinum foil counter electrode.TNAs up to 6.8 μm in length,120 nm in inner pore diameter,and 20 nm in wall thickness were obtained by 40 V potentials anodization for 24 h.Their microstructures and surface morphologies were characterized by XRD,TEM,SAED and UV-vis spectroscopy.The photoelectrochemical properties of as-prepared unsensitized and dye-sensitized TNAs electrodes were examined under simulated solar light (AM 1.5,100 mW/cm2) illumination.The results showed that the photocurrent of the dye-sensitized TNAs electrodes reached 6.9 mA/cm2,which was 6 times more than that of the dye-sensitized TiO2 nanoparticles (TNPs) electrodes.It implied that the electron transport process and the charge recombination suppression within TNAs electrodes were much more favorable in comparison with that in the TNPs electrodes.Electrodes applying such kind of titania nanotubes will have a potential to further enhance the efficiencies of TNAs-based dye-sensitized solar cells.     

表面In掺杂TiO2的N719/TiO2-Inx%/FTO薄膜电极的光电转换效率

采用溶胶-凝胶法制备出In 表面修饰的TiO₂ (TiO₂-Inx%)纳米粒子, x%代表在In 掺杂的TiO₂样品中In³⁺与In³⁺和Ti⁴⁺离子摩尔百分含量. 利用二(四丁基铵)顺式-双(异硫氰基)双(2,2''-联吡啶-4,4''-二羧酸)钌(II)(N719)作为敏化剂, 制备出N719/TiO₂/FTO (氟掺杂锡氧化物)和N719/TiO₂-Inx%/FTO染料敏化薄膜电极. 光电转换效率实验表明, 在薄膜电极+0.5 mol·L^-1 LiI+0.05 mol·L^-1 I₂的三甲氧基丙腈(MPN)溶液+Pt 光电池体系中,N719/TiO₂-Inx%/FTO薄膜电极的光电转换效率均高于N719/TiO₂/FTO, 其中N719/TiO₂-In0.1%/FTO的光电转换效率比N719/TiO₂/FTO提高了20%. 利用X 射线衍射(XRD)、X 射线光电子能谱(XPS)、漫反射吸收光谱(DRS)、荧光(PL)光谱和表面光电流作用谱确定了TiO₂-Inx%样品中In3+离子的存在方式和能带结构; 利用表面光电流作用谱研究了N719/TiO₂-Inx%/FTO薄膜电极的光致界面电荷转移过程. 结果表明, In3+离子在TiO₂表面形成O-In-Cl_n (n=1, 2)物种, 该物种的表面态能级位于导带下0.3 eV处; 在光电流产生过程中, O-In-Cl_n (n=1, 2)表面态能级有效地抑制了光生载流子在TiO₂-Inx%层的复合, 促进了阳极光电流的增加, 从而导致N719/TiO₂-Inx%/FTO薄膜电极的光电转化效率高于N719/TiO₂/FTO, 并进一步讨论了光致界面电荷转移的机理.     

Influence of Zn(II) adsorption on the photocatalytic activity and the production of H2O2 over irradiated TiO2

The photocatalytic activity of semiconductor oxides, in particular TiO₂ powders or colloids, is a complex function of bulk (light absorption and scattering, charge carrier mobility and recombination rate) and surface (structure, defects and reconstruction, charge, presence of adsorbate, surface recombination centers) properties. Among surface modifications, the inner sphere surface complexation of metal cations can change the surface charge of the metal oxide, thus changing the surface activity coefficient of ionic substrates, the band edge positions, as well as the mechanism and kinetic of interfacial electron transfer by blocking surface trapping sites for photogenerated carriers (≡Ti?OH). In this work we show that in anatase/water systems under band-gap irradiation, both the organic substrate (formate) oxidation initiated by photogenerated valence band holes and the formation of hydrogen peroxide from O₂ reduction (by conduction band electrons) is strongly influenced by the presence of Zn²⁺ cations. Depending on the pH, the formate oxidation rate can be enhanced or nearly completely inhibited. The observed result can be rationalized by considering the fraction of ≡Ti?OH surface sites blocked by inner sphere complexation of Zn²⁺ as a function of pH. When this fraction is low, the more positive surface charge favors formate oxidation, whereas when the fraction is high the almost complete blockage of ≡Ti?OH surface sites by Zn²⁺ stops almost entirely formate oxidation. Interestingly, the surface complexation of Zn²⁺ is accompanied by an increasing production of H₂O₂ during formate degradation in the presence of O₂. Zn(II) cations are not complexed by peroxide/superoxide species derived from O₂ reduction. When ≡Ti?OH sites are blocked by Zn²⁺, the complexation on the TiO₂ surface of peroxide/superoxide species is inhibited, hindering their further transformation. The results presented demonstrate that the combined effect of pH and surface complexation of redox inert cations greatly influences both the oxidative and reductive processes during the photocatalytic process over TiO₂.     

Monolayer V2O5/TiO2–ZrO2 catalysts for selective oxidation of o-xylene: preparation and characterization

A series of TiO₂?CZrO₂ supported V₂O₅ catalysts with vanadia loadings ranging from 4 to 12 wt% were synthesized by a wet impregnation technique and subjected to various thermal treatments at temperatures ranging from 773 to 1,073?K to understand the dispersion and thermal stability of the catalysts. The prepared catalysts were characterized by X-ray powder diffraction (XRD), BET surface area, oxygen uptake, and X-ray photoelectron spectroscopy (XPS) techniques. XRD results of 773?K calcined samples conferred an amorphous nature of the mixed oxide support and a highly dispersed form of vanadium oxide. Oxygen uptake measurements supported the formation of a monolayer of vanadium oxide over the thermally stable TiO₂?CZrO₂ support. The O 1s, Ti 2p, Zr 3d, and V 2p core level photoelectron peaks of TiO₂?CZrO₂ and V₂O₅/TiO₂?CZrO₂ catalysts are sensitive to the calcination temperature. No significant changes in the oxidation states of Ti⁴⁺ and Zr⁴⁺ were noted with increasing thermal treatments. Vanadium oxide stabilized as V⁴⁺ at lower temperatures, and the presence of V⁵⁺ is observed at 1,073?K. The synthesized catalysts were evaluated for selective oxidation of o-xylene under normal atmospheric pressure in the temperature range of 600?C708?K. The TiO₂?CZrO₂ support exhibits very less conversion of o-xylene, while 12 wt% V₂O₅ loaded sample exhibited a good conversion and a high product selectivity towards the desired product, phthalic anhydride.     

Iridium Anodic Oxidation to Ir(III) and Ir(IV) Hydrous Oxides

Iridium oxide films (IROFs) are known to have an enhanced or the so‐called super‐Nernstian (<59 mV/pH) pH‐sensitivity. The intention in the present study was to find out the reasons of such behavior and also to elucidate the nature of iridium anodic oxidation processes. The methods employed were combined cyclic voltammetry and chronopotentiometry. Iridium layers of 0.1 to 0.2 μm thickness, deposited thermally on titanium or gold‐plated titanium substrates, were used for investigations. IROFs on the surface of working electrodes were formed anodically by applying a constant potential in deaerated and oxygen‐containing solutions of 0.5 M H₂SO₄, 0.1 M KOH and 0.5 M H₃PO₄+KOH. Linear pH‐dependences of the stationary open‐circuit potential with the slopes close to 59 mV/pH were found for iridium electrode oxidized at 0.4 V–0.8 V (RHE) in deaerated and at 0.8 V–1.2 V (RHE) in O₂‐containing solutions. They were attributed to reversible Ir/Ir(OH)₃ and Ir/ IrO₂?nH₂O metal‐oxide electrodes, respectively. It has been suggested that the main current peaks seen in the voltammograms of iridium electrode in acid and alkaline solutions are of different nature. The difference between iridium electrode surface states in acid and alkaline solutions has been presumed to be the main reason of super‐Nernstian pH‐sensitivity of the IROFs. On the basis of the results obtained standard potential of Ir/Ir(OH)₃ electrode and the solubility product of Ir(OH)₃ have been evaluated: =0.78±0.02 V and K_sp=3.3×10^?64.     

Formation of a novel electroactive film by electropolymerization of 5-amino-1-naphthol

The electrooxidation of 5-amino-1-naphthol in acetonitrile solutions led to the formation of a purplish gray, air-stable, polymeric film (poly(5-amino-1-naphthol), poly(5,1-ANT)), which presents a nonfibrillar morphology, on basal-plane pyrolytic graphite and In-Sn oxide conducting glass (ITO) electrodes. The film showed a reversible, well-defined oxidation-reduction response in both aqueous solutions of pH 1–13 and protic non-aqueous solutions, and was semiconducting. The formal redox potential (E^o') was 0.075 V vs. a sodium chloride saturated calomel electrode in 0.2 M NaClO₄ aqueous solution (pH 1.0). The pH dependence of (E^o') suggested that the electrode processes at pH 1-5 and pH 8–13 are 1e⁻ − 1H⁺and 1e^t- − 2 H⁺ reactions, respectively. The poly(5,1-ANT) film-coated ITO electrode displayed an electrochromic character: the oxidized form is purplish gray and the reduced one is pale brownish yellow. In addition, based on the electrochemical and IR absorption spectroscopic characterization of the film, some possible candidates for the structures of electroactive moieties of poly(5,1-ANT) are proposed.     

A High-Performance Asymmetric Supercapacitor Based on Tungsten Oxide Nanoplates and Highly Reduced Graphene Oxide Electrodes

Tungsten oxide/graphene hybrid materials are attractive semiconductors for energy-related applications. Herein, we report an asymmetric supercapacitor (ASC, HRG//m-WO₃ ASC), fabricated from monoclinic tungsten oxide (m-WO₃) nanoplates as a negative electrode and highly reduced graphene oxide (HRG) as a positive electrode material. The supercapacitor performance of the prepared electrodes was evaluated in an aqueous electrolyte (1 m H₂SO₄) using three- and two-electrode systems. The HRG//m-WO₃ ASC exhibits a maximum specific capacitance of 389 F g⁻¹ at a current density of 0.5 A g⁻¹, with an associated high energy density of 93 Wh kg⁻¹ at a power density of 500 W kg⁻¹ in a wide 1.6 V operating potential window. In addition, the HRG//m-WO₃ ASC displays long-term cycling stability, maintaining 92 % of the original specific capacitance after 5000 galvanostatic charge–discharge cycles. The m-WO₃ nanoplates were prepared hydrothermally while HRG was synthesized by a modified Hummers method.     

A study of the photodeposition over Ti/TiO2 electrode for electrochemical detection of heavy metal ions

Here we reported that UV light irradiation can significantly enhance sensitivity of Ti/TiO₂ electrode for determination of trace heavy metal ions (such as Cu^2 +, Pb^2 + and Cd^2 +) owing to the photodeposition of metal ions on the surface of electrodes. The sensitivity of heavy metal ions can be selectively enhanced over the Ti/TiO₂ electrode, which is attributed to matching between potential of heavy metal ions and the position of the conduction band of TiO₂.     

钛基TiO2纳米管阵列电极的光电催化性能

应用电化学阳极氧化法在纯Ti基底上制备高度有序的TiO2纳米管阵列,考察了Ti/TiO2光阳极的光电化学响应.以苯酚溶液为目标污染物,研究Ti/TiO2电极的光电催化性能,并与光催化性能进行比较.结果表明,该电极光电催化性能优于光催化性能.施加0.6 V电压时,光电催化性能最好.电化学阻抗谱分析显示,光电催化和光催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

The effect of ionic and electronic properties of titanium oxide on the electrochemical growth and redox behavior of polyaniline on titanium surfaces

Polyaniline (PANI) was electrodeposited directly from aniline (ANI)-containing sulfuric acid media on Ti|TiO₂ electrodes, which were prepared in ANI-free 0.5 M H₂SO₄ solution by applying suitable anodization conditions in order to control the donor density (N _D) in the oxide layer of a fixed thickness. By using the suggested procedure, reproducible conditions for the cyclic voltammetric growth of PANI on Ti can be achieved, and most importantly, the properties of Ti|TiO₂|PANI electrodes can be modulated to meet the requirements for specific applications. The polymerization rate and the deposited amount of PANI were found to depend strongly on the N _D estimated by Mott-Schottky analysis. The redox behavior of the resulted Ti|TiO₂|PANI electrodes indicated differences in acid solutions as compared with the corresponding behavior of other PANI-modified metal surfaces. Analysis of the anodic and cathodic electrochemical response of the prepared Ti|TiO₂|PANI electrodes discloses the significant role of ionic and electronic properties of the intervening oxide between the metal support and PANI.