线偏振高斯光束通过复合型衍射光栅的传输特性

提出一种集合浮雕和折射率周期分布调制的复合型衍射光栅,并利用角谱表示和严格的模式理论研究了线偏振高斯光束通过这种复合型衍射光栅的传输特性.数值计算结果表明,在光栅的同一透射深度处复合型衍射光栅光强的起伏频率要比浮雕型光栅光强的起伏频率小.最后使用复合型衍射光栅模型,研究了亚波长体积相位全息光栅的表面起伏和入射光束的束腰宽度对衍射效率的影响. 关键词： 复合型衍射光栅 亚波长体积相位全息光栅 高斯光束 严格模式理论     

Direct Fabrication Methods of Surface Relief Electro-Optic Gratings in Azo-Polymer Films

Two fabrication methods of surface relief electro-optic (EO) gratings in azo-polymer films are described: surface deformation by a continuous wave laser and laser ablation by a pulse laser. In the fabrication process, the periodic intensity modulation of laser beams is formed by an interference fringe or a phase mask. The surface relief EO grating is fabricated by poling the surface relief grating (SRG) after the SRG fabrication process. The linear dependence of an applied voltage in the modulation efficiency of the first-order diffraction beam is observed. The proposed methods are effective for highly-efficient surface relief EO grating fabrication.     

Spontaneous nano pattern formation under pulsed exposure: relaxation kinetics study

Formation of spontaneous surface relief grating under pulsed exposure on the surface of an azo polymer film has been investigated. We did experiments in different repetition rates and pulse widths by use an electro mechanical chopper and a diode-pumped solid-state laser with wavelength of 532?nm as pump beam. Incidence of pump beam, has been set normal to the surface of azo-polymer film. Spontaneous surface relief grating with grating pitch of ~1,250?nm was formed. For low repetition rate, relaxation due to cis-trans isomerization becomes dominant and growth rate becomes slower. A threshold for spontaneous pattern formation was found. In addition to an increase in the diffraction intensity during illumination, anomalous variation of diffraction intensity by switching on and off the laser was observed. By switching off the recording beam sharp enhancement occurred. By switching on the recording beam, after a sharp decrease in the intensity of diffracted beam, it increased further under illumination. Anomalous variations, strongly depends on polarization of the probe beam and the irradiation time for the formation of spontaneous SRG. Sharp enhancement has been attributed to cis-trans thermal isomerization and sharp decrease has been attributed to isomeration in whole surface under illumination.     

Multistate polarization addressing using a single beam in an azo polymer film

Peculiar light-matter interactions can break the rule that a single beam polarization can address only two states in an optical memory device. Multistate storage of a single beam polarization is achieved using self-induced surface diffraction gratings in a photoactive polymer material. The grating orientation follows the incident light beam's polarization direction. The permanent self-induced surface relief grating can be read out in real time using the same laser beam.     

Temperature and orientation dependence of surface relief gratings based on dye-doped polymer film with the interface of nematic liquid crystals

The formation of surface relief grating on dye-doped polymer film with the interface of nematic liquid crystals has been investigated by means of the holographic technique. The first-order diffraction efficiency of surface relief grating depends on the temperature and the orientation of molecular director in the interface of nematic liquid crystals. The diffraction efficiency is roughly independent of thermal fluctuations of molecular director in the most part of nematic temperature range and apparently drops near the transition temperature. The morphology of surface relief grating demonstrates that the surface modulation is larger for molecular director parallel to the groove direction. The experimental result also shows that the first-order diffraction efficiency is dependent on the surface modulation of surface relief grating.     

Polarization holographic and surface-relief gratings at 257 nm in an amorphous azobenzene polyester

Polarization holographic and surface-relief gratings have been recorded in an amorphous azobenzene polyester by use of a frequency-doubled argon-ion laser beam at 257 nm. Higher excited states of azobenzene in the trans and cis configurations contribute to the formation of a diffraction grating in this experiment. A combination of right and left circularly polarized writing beams has been found to give the highest diffraction efficiency. The contributions to the total phase difference that arise from anisotropy and surface relief have been separated experimentally, and it is shown that the surface-relief grating contributes a larger phase difference than that which is due to anisotropy.     

Formation of positive and negative anisotropic holographic gratings depending on recording energy in photoreactive liquid crystalline copolymer films

Anisotropic diffractive gratings formed by birefringent molecular alignment are fabricated by a holographic technique using a photo-cross-linkable liquid crystalline copolymer (PLCCP). Depending on the exposure energy used for holographic recording, bright or dark regions of the interference fringe can be chosen for the molecular-aligned region, analogous to positive- and negative-type photoresist processing in photolithography. In conjunction with simultaneously generated surface relief gratings, the anisotropic refractive index modulation inherent in the PLCCP film exhibits different diffraction properties depending on the incident beam polarization. The anisotropic refractive index grating profiles are quantitatively presented for two cases determined by the exposure energy, based on the Fourier analysis of diffractive optics. The selection of different grating formations selected by varying only the exposure energy could provide a strategy for the fabrication of functionalized diffractive optical elements.     

Total internal reflection diffraction grating in conical mounting

The main conditions and parameters for obtaining surface relief total internal reflection diffraction gratings in conical mounting are presented. Calculated and experimental investigations reveal that there are ranges of grating periods, incidence angles, diffraction angles and gratings depths for which such gratings could be obtained, both for TE and TM polarizations. With optimized grating parameters the diffraction efficiency of the total internal reflection diffraction gratings can be greater than 90%.     

宽光谱高衍射效率脉宽压缩光栅设计和性能分析

基于飞秒激光对脉宽压缩光栅宽光谱和高衍射效率的要求,提出了一种金属介质膜结构的宽光谱高衍射效率脉宽压缩光栅,该光栅由基底、金属介质膜和表面浮雕结构组成.为获得宽光谱高衍射效率的脉宽压缩光栅,采用严格耦合波理论对金属介质膜光栅的结构参数进行优化设计.数值分析表明当金属介质光栅的槽深、剩余厚度、占空比和入射角分别为272 ...     

线偏振高斯光束通过条形浮雕光栅的传输

使用角谱表示和严格的模式理论研究了线偏振高斯光束通过特征尺寸与波长可比拟的条形浮雕光栅的传输，系统参数误差对浮雕层中光强最大值的影响.研究表明，光束在条形浮雕光栅各层中有不同的光强分布，浮雕层的介质填充部分中的光强明显高于展空部分的光强.光栅周期误差对浮雕层中最大光强的影响起主要作用.并利用模拟退火优化算法优化系统参数以控制出射光束的光强分布.     

Five-port beam splitter of a single-groove grating

A single-groove grating for five-port TE-polarization beam splitting under normal incidence at the wavelength of 1550 nm is presented. The transmitted diffraction efficiency of the gratings is over 94.5% with uniformity better than 2%. A physical view of diffraction inside the grating is presented by the simplified modal method(SMM).Initial parameters of the grating profiles are obtained by use of SMM and then optimized by employing rigorous coupled-wave analysis and the simulated annealing algorithm.     

The use of a diffraction grating as a beam expander in a dye laser cavity

The use of a diffraction grating as a dispersive one-dimensional beam expander with variable expansion ratio is described. The idea is applied to intracavity beam expansion in a dye laser cavity containing two gratings in a tandem configuration. By varying the beam expansion ratio up to 60 the laser linewidth may be reduced continously down to 0.1 cm^-1. Linewidth calculations based on single pass estimates are presented and found to agree with experimental results.     

Interferometric testing of the spacing error of a plane diffraction grating

Two measuring methods of the plane diffraction grating spacing error are presented in this work. The first one resembles real- time holographic interferometry. The hologram is exposed when an object beam is the nth diffraction order, and is then illuminated by the -nth diffraction order wave. The second method makes use of double-exposure holographic interferometry. The first exposure is performed when the nth diffraction order is an object beam. During the second exposure the -nth diffraction order is an object beam. Both methods allow to measure the spacing error separately, not only from the grating surface error but also from the aberrations introduced by the other optical elements of the set-up.     

Sudan IV dye based poly(alkyloxymethacrylate) films for optical data storage

The polymer poly{1-[2′-methyl-4′-(2″-methylphenylazo) phenylazo]-2-(m-methacryloyloxyoctyloxy}naphthalene, where m = 6, 8, 10, is synthesized by free radical addition polymerization method for holographic optical data storage. Characterization of the polymers is done by formation of the holographic grating. A study of the dependence of diffraction efficiency of the grating formed on various parameters is presented. Surface relief gratings on these polymer films are created upon exposure to argon ion laser beams at 514.5 nm without any subsequent processing steps. The surface structure of the relief gratings has been investigated by atomic force microscopy. The depth of surface relief in a typical case is found to be around 40 nm.     

Diffraction efficiency increase by corona discharge in photoinduced surface-relief gratings on an azo polymer film

The diffraction efficiency of a surface-relief grating (SRG) was dramatically increased by corona discharge. We fabricated this SRG by applying surface modulation to azo polymer films, using laser interference fringes. The electric charge was deposited upon the SRG by a corona discharge in an oven. The first-order diffraction efficiency measured before and after corona discharge above the glass-transition temperature increased from ~2% to ~40% in a SRG written with a circularly polarized beam. The relief depth of the SRG as measured with an atomic-force microscope also increased, from ~130 nm to ~450 nm. The increase in diffraction efficiency was independent of the writing polarization.     

Three Gaussian beam heterodyne interferometer for surface profiling

A novel three Gaussian beam interferometric technique for profiling optical smooth surfaces is presented. The technique is based on the heterodinization of three Gaussian beams, two of them with the same temporal frequency. The first beam is used as a probe beam after being focused and reflected from the surface under test. The second beam is reflected from a reference surface. The third beam is obtained from the first diffraction order of a Bragg cell and thus, it is shifted in its temporal frequency. The three beams are coherently added at the sensitive plane of a photodetector that integrates the overall intensity of the beams. We show analytically that the electrical signal at the output of the photodetector consists of a temporal carrier whose amplitude is a sinusoidal function of the local topography. We include the measurement of the topography of a sample consisting in a blazed-reflecting grating calibrated by means of an atomic force microscope.     

Asymmetric dynamic phase holographic grating in nematic liquid crystal

A new scheme for recording a dynamic phase grating with an asymmetric profile in C60-doped homeotropically aligned nematic liquid crystal(NLC) was presented.An oblique incidence beam was used to record the thin asymmetric dynamic phase holographic grating.The diffraction efficiency we achieved is more than 40%,exceeding the theoretical limit for symmetric profile gratings.Both facts can be explained by assuming that a grating with an asymmetric saw-tooth profile is formed in the NLC.Finally,physical mechanism and mathematical model for characterizing the asymmetric phase holographic grating were presented,based on the photo-refractive-like(PR-like) effect.     

Electric field assisted holographic recording of surface relief gratings in an azo-glass

The formation of holographic gratings in an azo-glass is investigated for the simple case of an intensity grating in the s-polarization of the recording beams. A dual grating is formed as a function of time with a refractive index grating and a relief grating. The diffraction efficiency as a function of recording time is discussed in a model of two consecutive processes with a phase shift. A material transport process is involved in the formation of relief patterns. An additional electrical corona field perpendicular to the sample leads to a magnification of the relief pattern. This process also works in case of a homogeneous exposure. PACS 78.66.Qn; 42.40.Eq; 42.70     

Dynamic thermometry of a solid via optical diffraction method at pulsed irradiation

A method for the fast measurement of the temperature of solids under the action of a high-power light pulse is proposed and demonstrated. This method is based on the application of the Fraunhofer diffraction and is implemented for silicon samples heated to melting temperatures T _melt = 1412°C by a high-power light pulse. The current silicon temperature was determined by measuring the varying diffraction angle of the probing laser beam. The diffraction angle was varied over time because the period of the diffraction grating increased as a result of the dynamic thermal expansion of the crystal. An initial grating was formed on the surface of the silicon plate with a period of d = 4 μm. The radiation beam of a He-Ne laser with λ = 0.6328 μm was used as the probing beam; the measured signal was recorded in the pair of symmetric fifth-order diffraction maxima.     

New method of increasing diffraction efficiency of grating transferred in glass substrate by corona-charging treatment

We propose a new method of increasing the diffraction efficiency of a glass substrate onto which a grating structure has been transferred by corona-charging treatment. The first-order diffraction efficiency was successfully increased by at least 100-fold by a simple low-cost process in which an aqueous solution prepared from poly(vinyl alcohol) (PVA) and glucose was spin-coated on the glass substrate. As the solution dried, the spin-coated film formed a periodic surface relief grating with the period corresponding to that of the grating transferred to the glass substrate. The period and depth of the relief structure were 50 and 1.4 μm, respectively. The depth of the relief structure strongly depended on the concentrations of PVA and glucose in the solution. Under our experimental conditions, a high first-order diffraction efficiency was obtained when the PVA concentration was 7.5–8 wt% and the glucose concentration was 30–45 wt %.