锰氧化物负载碳氮三维网络结构复合材料的制备及锂电性能

通过硝酸锰和乙醇的水热反应在三聚氰胺泡棉（MF）上生成三氧化二锰颗粒,氮气下高温处理后形成锰氧化物负载碳氮三维网络结构的复合物。碳氮网络结构提高了充放电过程中材料结构的稳定性及导电性,且烧结过程中产生的孔道结构有利于锂离子传输,使得该复合材料作为负极在锂离子电池中表现出优异的充放电性能和循环稳定性。材料的比容量和循环稳定性大大提高,经500℃处理后的MnO/CNnws-500材料在160次循环后仍然保留590 mAh·g^-1的比容量,达到氧化亚锰理论容量755 mAh·g^-1的78%。     

锰氧化物/碳氮三维网络结构复合材料的制备及锂电性能

通过硝酸锰和乙醇的水热反应在三聚氰胺泡棉(MF)上生成三氧化二锰颗粒,氮气下高温处理后形成锰氧化物负载碳氮三维网络结构的复合物。碳氮网络结构提高了充放电过程中材料结构的稳定性及导电性,且烧结过程中产生的孔道结构有利于锂离子传输,使得该复合材料作为负极在锂离子电池中表现出优异的充放电性能和循环稳定性。材料的比容量和循环稳定性大大提高,经500℃处理后的MnO/CNnws-500材料在160次循环后仍然保留590 m Ah·g~(-1)的比容量,达到氧化亚锰理论容量755 m Ah·g~(-1)的78%。     

静电纺丝法制备Mn2O3纳米纤维及其磁性研究

采用溶胶-凝胶过程和静电纺丝技术相结合方法, 以聚丙烯腈和醋酸锰为前驱物, 制得了PAN/Mn(CH₃COO)₂复合纳米纤维. 将该复合纤维高温煅烧, 获得了Mn₂O₃纳米纤维. 采用扫描电镜(SEM)、红外光谱(FTIR)、差热-热重(TG-DTA)和X射线衍射(XRD)分析等对样品进行了表征. 结果表明, Mn₂O₃纳米纤维为规则的一维结构, 直径分布均匀, 具有铁磁性-反铁磁性-顺磁性相互转化的特性.     

长寿命高镍无钴锂离子正极材料的制备

通过调整不同配锂量、不同焙烧温度以及包覆改性对高镍无钴二元材料性能的影响因素进行了研究。对不同原样和其改性后的材料进行了X射线粉末衍射(XRD)分析和首次充放电性能和倍率性能、循环性能等电化学性能测试。其中过锂量(质量分数)为5%,焙烧温度为820℃的材料性能优异,其首次放电比容量为171.6 mAh·g^-1,1C和3C的放电比容量分别为147.8、129.8 mAh·g^-1。对材料进行锰化合物(质量分数1.0%)包覆处理后,材料的残碱量下降明显,加工性能优异,倍率性能得到明显改善,1C和3C的放电比容量分别提升为156.5、141.8 mAh·g^-1。2Ah软包电池常温循环830周容量保持率为80%,高温循环345周容量保持率为80%。     

Preparation of Mn2O3 and Mn3O4 nanofibers via an electrospinning technique

Thin PVA/manganese acetate composite fibers were prepared by using sol-gel processing and electrospinning technique. After calcinations of the above precursor fibers, Mn₂O₃ and Mn₃O₄ nanofibers with a diameter of 50-200 nm could be successfully obtained. The fibers were characterized by TG-DTA, Scanning electron microscopy, FT-IR, WAXD, respectively. The results showed that the crystalline phase and morphology of nanofibers were largely influenced by the calcination temperature.     

用于超级电容器的锰钴氧化物/碳纤维材料

The development of high-performance supercapacitor electrode materials is imperative to alleviate the ongoing energy crisis. Numerous transition metals (oxides) have been studied as electrode materials for supercapacitors owing to their low cost, environmental-friendliness, and excellent electrochemical performance. Among the developed binary transition metal oxides, manganese cobalt oxides typically show high theoretical capacitance and stable electrochemical performance, and are widely used in the electrode materials of supercapacitors. However, the poor conductivity and active material utilization of manganese cobalt oxide-based electrode materials limit their potential capacitance application. Cotton is mainly composed of organic carbon-containing materials, which can be transformed to carbon fibers after calcination. The resultant carbonaceous material exhibits a large specific surface area and good conductivity. Such advantages could potentially suppress the negative effects caused by the poor conductivity and small specific surface area of manganese cobalt oxides, thereby improving the electrochemical performance. Herein, we firstly deposited manganese cobalt oxides on cotton by a simple hydrothermal method, yielding a composite of manganese cobalt oxides and carbon fibers via subsequent calcination, to improve the electrochemical performance of the electrode material. X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), thermogravimetric analysis (TGA), and electrochemical characterizations were used to investigate the physical, chemical, and electrochemical properties of the prepared samples. The fabricated manganese cobalt oxides in the composite were uniformly dispersed on the carbon fiber surface, which increased the contact between the interface of the electrode material and electrolyte, and enhanced electrode material utilization. The electrode material was confirmed to have well contacted with the electrolyte during a contact angle test. Hence, a pseudo-capacitance reaction completely occurred on the manganese cobalt oxide material. Moreover, the addition of carbon fibers reduced the resistance of the material, resulting in excellent capacitive performance. The capacitance of the prepared composite was 854 F∙g^-1 at a current density of 2 A∙g^-1. The capacitance was maintained at 72.3% after 2000 cycles at a current density of 2 A∙g^-1. These results indicate that the manganese cobalt oxide and carbon fiber composite is a promising electrode material for high-performance supercapacitors. The findings presented herein provide a strategy for coupling with carbon materials to enhance the performance of supercapacitor electrode materials based on manganese cobalt oxides. Thus, novel insights into the design of high-performance supercapacitors for energy management are provided.     

Lithium storage mechanisms and effect of partial cobalt substitution in manganese carbonate electrodes

A promising group of inorganic salts recently emerged for the negative electrode of advanced lithium-ion batteries. Manganese carbonate combines low weight and significant lithium storage properties. Electron paramagnetic resonance (EPR) and magnetic measurements are used to study the environment of manganese ions during cycling in lithium test cells. To observe reversible lithium storage into manganese carbonate, preparation by a reverse micelles method is used. The resulting nanostructuration favors a capacitive lithium storage mechanism in manganese carbonate with good rate performance. Partial substitution of cobalt by manganese improves cycling efficiency at high rates.     

Formation of Ultrafine Apatite Fibers by Sol-gel/Electrospinning

Ultrafine apatite fibers were prepared by electrospinning of sol-gel precursor/poly（ vinyl pyrrolidone） （PVP） solutions followed by subsequent calcination. The as-electrospun and calcinated fibers were observed under a scanning electron microscope and an optical polarizing microscope. Results show that the morphology and the diameter of as-electrospun fibers strongly depend on the viscosity and the surface tension of sol-gel precursor/PVP solutions. After calcination, the smooth as-electrospun fibers shrink and the fiber diameter decreases because of the removal of the polymer. The chemical evolution upon the transformation of the precursor from a gel to the final apatite fibers was investigated by thermogravimetric-differenfial thermal analysis, X-ray diffraction, and Fourier transform infrared spectroscopy. It is thus suggested that the crystalline structure of the calcined fibers is largely influenced by the calcination temperature. After being calcined at 600 ℃, the apatite fibers with a diameter of about 280 nm containing β-tricalcium phosphate were obtained.     

掺钛尖晶石锂锰氧化物的合成、结构及电化学性能研究

以掺钛电解二氧化锰为锰源合成了一系列掺钛尖晶石锂锰氧化物样品.实验结果表明,无论是在新制样品40次循环的充放电实验中,还是在经过40次循环充放电并在放电状态下贮藏3个月的再次充放电实验中,掺钛样品均具有极好的电化学性能.600℃掺钛样品在第一循环中的放电容量达到206mA·h/g.在放电态贮藏3个月后,再次充放电实验中,第一循环的放电容量达到144mA·h/g.XRD分析表明,掺钛样品仍然具有立方结构.还用红外和拉曼光谱技术研究了钛对尖晶石锂锰氧化物的电化学性能的改善作用.     

Effects of Metal Ion Sources on Synthesis and Electrochemical Performance of Spinel LiMn2O4 Using Tartaric Acid Gel Process

The effect of lithium and manganese ions on the synthesis, phase purity, and electrochemical properties of tartaric acid gel processed lithium manganese oxide spinel were investigated. The poor bonding between both lithium and manganese ions with tartaric acid was shown by the FT-IR analysis when lithium nitrate and/or manganese nitrate were used as sources. Li₂MnO₃ and Mn₂O₃ impurities formed in addition to lithium manganese oxides when nitrate salts were used as the sources. When acetate salts were used as sources for the lithium and manganese ions, single-phase LiMn₂O₄ was obtained. These results indicate that homogeneous bonding between acetate salt and tartaric acid was formed. The capacity of single-phase LiMn₂O₄ calcined at 500°C was 117 mAh/g which was much higher than those containing Mn₂O₃ and Li₂MnO₃ impurity compounds. Thus, sources of lithium and manganese ions play an important role in the synthesis and electrochemical behaviors of lithium manganese oxide spinel.     

NMR and FT-IR Investigation of Spinel LiMn2O4 Cathode Prepared by the Tartaric Acid Gel Process

The structure of the lithium manganese tartrate precursor and the synthesis mechanism of LiMn₂O₄ were investigated by FT-IR, NMR, TG/DSC, and XRD in this study. The results of FT-IR and ⁷Li and ¹³C NMR measurements revealed that lithium ions bond with carboxylic acid ligands and the O–H stretching modes of tartaric acid. Manganese ion bonds only with carboxylic acid. Lithium and manganese ions were trapped homogeneously on an atomic scale throughout the precursor. Such a structure eliminates the need for long-range diffusion during the formation of lithium manganese oxides. Therefore, spinel LiMn₂O₄ was synthesized at temperatures as low as 300°C. In this work, the electrochemical properties of Li/Li_xMn₂O₄ were studied. It is clear that the discharge curves exhibit two pseudo plateaus as the LiMn₂O₄ is fired to higher temperatures. The discharge capacity of LiMn₂O₄ increases from 84 to 117 mAh/g as the calcination temperature increases from 300 to 500°C. The LiMn₂O₄ powders calcined at low temperatures with a high specific surface area and an average valence of manganese exhibit a better cycle life.     

锂离子电池锂锰氧化物高压嵌锂材料的结构和电化学性能研究

利 用 Ｘ Ｒ Ｄ、 Ｉ Ｃ Ｐ、 Ｔ Ｇ Ａ 、 Ｄ Ｔ Ａ 及 恒 流 充 放 电 等 方 法 研 究 分 析 了 一 种 特 殊 天 然 结 构 Ｍｎ Ｏ２（ Ｎ Ｍ Ｄ） 材料的结 构、组成 以及电 化学嵌锂 特性． Ｘ Ｒ Ｄ 分析 表明,该样 品材料 是由钠水 锰矿以及水羟 锰矿复 合结构组 成的 Ｍｎ Ｏ２ 纳米 纤 维． 充放 电 循环 结果 显 示,其 前 期循 环容 量 可高 达 １５０ｍ Ａｈ／ ｇ 左 右,但性 能尚不够 稳定． 本文采 用一种 水热法高 压嵌锂处 理,可将 Ｎ Ｍ Ｄ 样品 转变为 具有３ ×３ 大隧道结 构的钡 镁锰矿（ Ｔｏｄｏｒｏｋｉｔｅ） 型锂 锰氧 化 物,既 增 强了 Ｌｉ ＋ 嵌 入 隧道 或 层间 结 构 的循环稳定 性． 并 显著提 高锂锰氧 化物电 极材料性 能的 稳定 性,以 充放 电电 流密 度 为０ ．８ ｍ Ａ／ｃ ｍ ２ ,经过１８０ 次 循环后 其比容量 仍具有 １１０ ｍ Ａｈ／ ｇ ． 该类 大隧道结 构锂锰 氧化物可 作为一 种３ Ｖ 的锂离子电极 材料．     

Titania-Doped Silica Fibers Prepared by Electrospinning and Sol-Gel Process

Titania-doped silica fibers were prepared by electrospinning of the sol of silica containing titania. The electrospun fibers had ribbon type morphology. The fibers had significant quantities of hydroxyl groups of Si—OH and Ti—OH. The fibers did not have crystalline structure. Diameters of the fibers were reduced by solvent evaporation and calcination. The hydroxyl groups on the fibers disappeared by calcination. The hydroxyl groups, M—OH (MSi, Ti) were changed to M—O—M by intermolecular and intramolecular condensation reactions.     

Birnessite和Cryptomelane型氧化锰的可控合成及其催化性能

以葡萄糖和高锰酸钾为原料,采用溶胶-凝胶法合成了birnessite(K_(1.35)MnO_2,简写为Bir)和cryptomelane(K_(0.27)MnO_2,简写为Cry)型氧化锰;采用X射线衍射、原子吸收光谱等考察了凝胶处理方法、反应物浓度比、焙烧温度和反应时间等对氧化锰晶型的影响.结果表明,采用不同方法处理凝胶可实现对Bir和Cry型氧化锰的可控合成.以不同的处理方法,葡萄糖和高锰酸钾的浓度比为O.74,反应20s制成凝胶,并在400℃焙烧2h,可分别制取高结晶度和高纯度的Bir和Cry型氧化锰.Bir和Cry型氧化锰在二甲醚燃烧反应中表现出优异的催化性能,且Cry型氧化锰的催化活性更高.     

Synthesis and characterization of phase-pure manganese(II) and manganese(III) silicalite-2

Manganese silicalite-2 was synthesized at high pH using the molecular cluster Mn 12O 12(O 2CCH 3) 16 as a Mn source. The silicalite-2 (ZSM-11) materials were synthesized using 3,5-dimethyl- N, N-diethylpiperdinium hydroxide as a structure-directing agent to produce phase-pure ZSM-11 materials. No precipitation of manganese hydroxide was observed, and synthesis resulted in the incorporation of up to 2.5 mol % Mn into the silicalite-2 with direct substitution into the framework verified by the linear relationship between the unit cell volume and loading. The Mn is reduced to Mn (II) during hydrothermal synthesis and incorporated into the silicalite-2 framework during calcination at 500 degrees C. Further calcination at 750 degrees C does not affect the crystallinity but oxidizes essentially all of the Mn (II) to Mn (III) in the framework. The large difference in oxidation temperatures between the II and III oxidation states provides a means of producing relatively pure manganese(II) and manganese(III) silicalite-2 materials for applications such as catalysis.     

Electrospun Nickel Oxide Hollow Nanostructured Fibers

The citric acid/nickel acetate composite hollow fibers were prepared by using sol-gel processing and co-electrospinning technique. The polycrystalline NiO hollow nanostructured fibers were prepared after calcination. The obtained hollow nanostructured fibers made up of 17～25 nm nanocrystals were about 150 nm to several micrometers in outer diameter. The hollow NiO nanostructured fibers have been characterized by TG, DSC, SEM, FTIR, and XRD techniques. The results showed that the morphology of NiO hollow fibers was obviously influenced by the calcination temperature.     

尖晶石LiMn2O4纳米粉的合成 及其交流阻抗性能研究

以LiOH和电解二氧化锰(EMD)为原料,葡萄糖为还原剂,制备了粒径为200nm左右的球状尖晶石LiMn2O4纳米粒子,并用X射线衍射(XRD)和扫描电镜(SEM)对样品进行了结构和形貌的表征.在循环伏安测试(CV)峰电位下研究了该材料嵌脱锂相变过程中的交流阻抗(EIS)图谱,并提出一种新的等效电路对EIS图谱进行拟合...     

静电纺丝法制备NiO纳米纤维及其表征

纳米级NiO因具有优良的催化和热敏等性能而被广泛用于催化剂^[1]、电池电极^[2,3]、光电转化材料^[4～6]、电化学电容器^[7～8]等诸多方面.迄今,已成功地制备出N iO的纳米颗粒^[9]、纳米线^[10]及纳米薄膜^[11],但是对于具有准一维结构的NiO纳米纤维的制备及性能研究尚未见报道.     

富锂锂锰氧化物的制备及其在溶液中的抽Li+/吸Li+性能

采用柠檬酸配合法合成了系列尖晶石富锂锂锰氧化物Li2O.nMnO2(n=1.75,2.0,2.25,2.5,3.0)。通过X射线衍射(XRD)和酸浸实验发现,350℃合成的Li2O.2.25MnO2具有纯相尖晶石锂锰氧化物结构,且在弱酸性介质中具有较高的锂溶出率和较低的锰溶损率。Li2O.2.25MnO2在酸浸之后转型为锂离子筛。XRD和扫描电子显微镜(SEM)分析发现锂离子筛能够保持尖晶石锂锰氧化物的结构和形貌。吸附实验表明,该锂离子筛在碱性含锂溶液中对Li+具有吸附性能,且吸附容量随着溶液温度和pH值的升高而增大,最高能达到40.14 mg.g-1。通过傅立叶红外光谱(FTIR)研究了锂离子筛的吸附机理,并用Langmuir模型描述了其在LiCl+LiOH溶液中的吸附行为。     

Catalytic combustion of ethyl acetate over CeMnO_x and CeMnZrO_x compounds synthesized by coprecipitation method

Ce0.6Mn0.4O2 catalysts with different sources of manganese and Ce0.6-xZrxMn0.4O2 mixed oxide catalysts were prepared by coprecipitation method and were characterized by N2 adsorption-desorption,TPR,XRD,and XPS techniques.The activities of the prepared catalysts for ethyl acetate combustion,and the effects of calcination temperature and space velocity on catalytic activity were investigated.The results showed that partial replacement of Mn(NO3)2 with KMnO4 as sources of manganese could improve activities of catalysts.Ce0.45Zr0.15Mn0.4O2 catalyst exhibited the best catalytic activity and high thermal stability,e.g.,T90 could be still below 210℃ even if space velocity was up to 20000h-1.