Graft Copolymerization of Acrylamide on Swollen poly (Ethylene Terephthalate) Fibers Using Cerium Ammonium Nitrate Initiator

Abstract

In this study the graft copolymerization of acrylamide (AAm) on swollen poly(ethylene terephthalate) (PET) fibers using cerium ammonium nitrate (CeAN) initiator was investigated. Five organic solvents, dimethylsulfoxide (DMSO), morpholine, acetic acid (HAc), n-butanol, and 1,2-dichloroethane (DCE), were used as swelling agents. DMSO was found to be the most suitable swelling agent. Solvent diffusion into the fibers was observed to increase with treatment time and temperature. The optimum graft yield was obtained when fibers were grafted after having been swollen in DMSO for a period of 1 hour at 140°C. Variation of graft yield with polymerization time and temperature, and monomer, initiator, and acid concentrations were investigated. Graft yields were observed to increase initially with polymerization time, then to level off, and were found to increase up to a certain monomer and Ce⁴⁺ concentration, then to decrease slightly. The effect of grafting on such fiber properties as diameter, viscosity, and moisture gain were also investigated.     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Graft polymerization of vinyl monomers inside macroporous polyacrylamide gel,cryogel, in aqueous and aqueous‐organic media initiated by diperiodatocuprate(III) complexes

Graft polymerization initiated by diperiodatocuprate(III) complex (Cu(III)) initiator was found to be an effective and convenient method for graft polymerization of vinyl monomers onto macroporous polyacrylamide gels, the so‐called cryogels (pAAm‐cryogels). The effect of time, temperature, monomer and initiator concentration during the graft polymerization in aqueous and aqueous‐organic media was studied. The graft polymerization of water‐soluble monomers as [2‐(methacryloyloxy)ethyl]‐trimethylammonium chloride, 2‐hydroxyethyl methacrylate, N‐isopropylacrylamide, and N,N‐dimethylacrylamide proceeds with higher grafting yield in aqueous medium, as compared with that in aqueous‐organic media. Graft polymerization in aqueous‐organic media such as water–DMSO solutions allows grafting of water‐insoluble monomers such as glycidyl methacrylate and N‐tert‐butylacrylamide with high grafting degrees of 100 and 410%, respectively. It was found that the deposition of initiator on the pore surface of cryogels promoted graft polymerization by facilitating the formation of the redox couple Cu(III)‐acrylamide group. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1952–1963, 2006     

Characterization and Studies on Grafting of Methyl Methacrylate onto PAN Fibers

The graft copolymerization of methyl methacrylate (MMA) onto commercial acrylic fibers (PAN) has been studied using Azobis(isobutyro)nitrile (AIBN) as an initiator. MMA grafting initiated by radicals formed from thermal decomposition of AIBN. In this study, the effects of monomer and initiator concentration, time and temperature reaction on the grafting yield have been investigated.

The optimum conditions for this grafting reaction were obtained with an MMA concentration of 0.7 M, an AIBN concentration of 0.0073 M, a reaction temperature of T=85°C and with a 60 min reaction time.

The fiber structure has been investigated by different experimental techniques of characterization such as Fourier transform infrared spectroscopy (FT‐IR), calorimetric analysis (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), water absorption and the physical and mechanical properties has also been investigated in this study. The thermal analysis data showed that by increasing grafting yield, little changes have occurred in fibers samples up to 13.5% of grafting yield and the thermal transitions of grafted fibers have approximately the same behavior compared with the raw fibers sample. Grafting also slightly affected the fiber morphology. The experimental data of mechanical properties clearly show that by increasing grafting yield, max extension will decrease but this change up to 13.5% grafting yield is barely noticeable. Grafting of poly MMA improved water absorption.     

Dimethylaniline (DMA)–Cu2+ ion system-induced graft polymerization of methyl methacrylate on viscose

Graft polymerization of methyl methacrylate on viscose fibers induced by the DMA–Cu²⁺ ion system was investigated under different conditions. Variables studied include concentration of DMA, Cu²⁺ ion, and MMA, reaction time, and temperature. There are optimal concentrations of DMA and Cu²⁺; below or above these concentrations lower grafting occured. Within 4 hr reaction time, the grafting reaction showed an initial fast rate followed by a slower one at 80°C. At 70°C, on the other hand, the graft yield increased in proportion to the increase in reaction time. Increasing the monomer concentration did not have a significant effect on the graft yield during the first 45 min of reaction. Beyond this, the effect of monomer concentration was marked.     

Graft Copolymerization of Methyl Methacrylate onto Nylon 6 Using Thallium(III) Ions as Initiator

Abstract

Graft copolymerization of methyl methacrylate onto nylon 6 was investigated in aqueous perchloric acid medium using thallium(III) ions as initiator. The rate of grafting was evaluated by varying the concentrations of monomer, initiator, acid, and temperature. The rate of grafting was found to increase with an increase of both monomer and initiator concentrations. The graft yield was found to increase with an increase in the acid concentration up to 0.49 mL^?1, and beyond this concentration of perchloric acid the graft yield was found to decrease. It also increased with an increase of temperature. From the Arrhenius plot the overall activation energy was found to be 3.9 kcal/mol. The effects of inhibitors, various solvents, inorganic salts, and swelling agents on graft yield were studied. A suitable kinetic scheme has been proposed and a rate equation has been derived.     

Solvent “Goodness” in Polymer Separation by Flow

The graft copolymerization of methyl methacrylate onto silk fibers was investigated in aqueous solution using the V⁵⁺?thiourea redox system. The rate of grafting was determined by varying monomer, thiourea, acidity of the medium, temperature, initiator concentration, and reaction medium. The percentage of graft yield increases significantly by increasing the initiator concentration up to 0.01 M and thereafter decreases with a further increase of initiator concentration. The graft yield increases with an increase of thiourea concentration up to 10.0 × 10^?4 and then decreases with a further increase of thiourea concentration. The effect of increasing the monomer concentration brings about a significant enhancement in the graft yield. A suitable kinetic scheme has been proposed and the rate equation has been evaluated.     

Grafting Vinyl Monomers onto Silk Fibers. XIII. Graft Copolymerization of Methyl Methacrylate onto Silk Using Fe3+−Cysteine Redox System

The graft copolymerization of methyl methacrylate onto silk fibers initiated by the ferric chloride-eysteine redox system has been investigated in aqueous medium. The rate of grafting was calculated by varying the concentrations of monomer, initiator, acidity of the medium, cysteine, and temperature. The percentage of grafting increases with an increase of Fe³⁺ concentration up to 2,5 × 10^?3 mol/L and thereafter it decreases. The graft yield increases steadily upon increasing the monomer concentration. The graft yield also increases with increasing cysteine concentration up to 0.5 × 10^?3 mol/L and then decreases. The effect of the perchloric acid concentration, temperature, solvents, and certain neutral salts on graft yield has also been investigated and a suitable reaction scheme has been proposed.     

Grafting vinyl monomers onto silk fibers. IX. Graft copolymerization of methyl methacrylate onto silk using peroxydiphosphate-thiourea redox system

The graft copolymerization of methyl methacrylate (MMA) onto silk in aqueous media initiated by the potassium peroxydiphosphate-thiourea redox system was studied at 50°C. The rate of grafting was determined by changing [monomerl], [thiourea], [initiator], acidity of the medium, reaction medium, and temperature. A significant increase percent of grafting was noticed with increasing monomer concentration to 84.49 × 10^?2 mole/liter and the further increase is associated with the decrease of graft yield. The graft yield increases with an increase of thiourea (Tu) concentration to 25 × 10^?5 mole/liter; then it decreases. A measurable increase in graft yield was observed with an increase in acidity of the medium. Graft yield increases to a certain temperature, i.e., 50°C, and then it decreases. The graft yield increases with an increase of initiator concentration to 60 × 10^?4 mole/liter; then it decreases. The graft yield is medium dependent. A suitable kinetic path has been proposed and the rate equation has been derived.     

A study of the graft copolymerization of methacrylic acid onto starch using the H2O2/Fe++ redox system

Graft copolymerization of methacrylic acid (MetAc) onto potato starch using H₂O₂/Fe⁺⁺ redox system was investigated. The best conditions of the grafting reaction were determined and several variables were studied: initiator and monomer concentrations, time, and temperature. Percent grafting efficiency, percent grafting, percent grafted monomer conversion, and total conversion were obtained. The optimum graft yield was obtained at 7.3 × 10^?3M H₂O₂ concentration and it was favored by increasing the methacrylic acid concentration and reaction time.     

Preparation of Poly(ethylene terephthalate)‐g‐Methacrylamide Copolymers Initiated by Azobisizobutyronitrile: Characterization and Investigation of Some Properties

Poly(ethylene terephthalate)‐g‐methacrylamide (PET‐g‐MAAm) copolymer was prepared by graft copolymerization in organic solvent/water mixtures by using azobisizobutyronitrile (AIBN) as an initiator. The highest graft yield was obtained in 20/80 (v/v) acetonitrile/water mixture as 30.0%. The effect of polymerization parameters such as the ratio of solvent/water mixture, concentrations of initiator and monomer, temperature and time on the graft yield was studied. The moisture regain of the PET fiber increased with grafting from 0.42% to 3.01%. Thermogravimetric data showed that the thermal stability of PET fibers decreased with grafting and 85% of total weight of 29.7% grafted fiber was lost at 500°C. On the other hand, fiber density decreased with increasing graft yield. At SEM micrographs, the layers oriented in the direction of fiber length were observed on the surface of PET fiber as a result of grafting.     

Graft Copolymerization of Methyl Methacrylate on Potato Starch Using Potassium Trioxalatomanganate,K3[Mn(C2O4)3], as Initiator

Graft copolymerization of methyl methacrylate on potato starch was carried out in methanol-water medium at 35°C in the dark using potassium trioxalatomanganate, K₃[Mn(C₂O₄)₃], as initiator. The effect of different methanol-water ratios (v/v), the temperature of polymerization, the initiator concentration, the monomer concentration, the starch content, and the time of polymerization were studied. Percent total conversion, % grafting, and grafting efficiency (%) under different conditions were evaluated and compared. High grafting efficiency (～80%), high % total conversion (～85%), and high % grafting (-95%) were readily obtained. The reaction mechanism for graft copolymer formation is discussed.     

Polymerization of Acrylamide in Aqueous Solution of Poly(N‐isopropylacrylamide) at Lower Critical Solution Temperature

Acrylamide (AAm) was found to polymerize in a solution of poly(N‐isopropylacrylamide) (PNIPAAm) in water at around its lower critical solution temperature (LCST) (32°C) without any initiators. This phenomenon was specifically observed in aqueous solutions of the polymers having LCST such as PNIPAAm and poly(methylvinylether) (PMVE). AAm polymerized only when PNIPAAm and AAm were dissolved in water below LCST of PNIPAAm and then the solution was warmed up to the polymerization temperature (40°C). On the other hand, the polymerization of AAm did not proceed when AAm was added into aqueous PNIPAAm solution during and after the phase separation above 32°C. Furthermore the polymerizability of AAm was remarkably affected by the concentration and molecular weight of the PNIPAAm additives. Under the condition of lower PNIPAAm concentration (0.30 mol/L), the increase in the molecular weight of PNIPAAm considerably increased the molecular weight of the resulting PAAm but decreased the yield of PAAm. Under the condition of higher PNIPAAm concentration (0.60 mol/L) the polymerizability was not so affected by the molecular weight of PNIPAAm, while the molecular weight of PAAm formed by using higher molecular weight PNIPAAm was higher than those of PAAm formed by using lower molecular weight PNIPAAm. Moreover, the molecular weight of PAAm formed by the PNIPAAm induced polymerization of AAm was much higher than that of the polymer obtained by the radical polymerization using AIBN in THF or VA‐ 061 in water.     

Graft copolymerization onto rubber. V. Graft copolymerization of methyl methacrylate onto rubber using potassium peroxydiphosphate as initiator

The graft copolymerization of methyl methacrylate onto natural rubber (NR) is investigated using potassium peroxydiphosphate as the initiator. The rate of grafting is determined by varying monomer concentration, peroxydiphosphate concentration, and temperature. The graft yield increased with an increase in monomer concentration up to 1.4082M/L and thereafter the graft yield decreases. The graft yield increases significantly with an increase of peroxydiphosphate concentration up to 150 X 10^-1M/L and thereafter the graft yield decreases. The grafting reaction is temperature dependent. A suitable kinetic scheme is proposed and the rate equation is evaluated.     

[Mn(H_2P_2O_7)_3]~(3-)引发淀粉与丙烯腈接枝聚合反应的动力学研究

以[Mn(H_2P_2O_7)_3]~(3-)为引发剂,研究了丙烯腈与玉米淀粉的接枝共聚反应。由实验结果求出了反应速率与引发剂浓度、单体浓度、淀粉浓度和反应温度的关系,推导并验证了接枝反应动力学模型,探讨了反应机理,求得了接枝反应活化能。     

Radiation initiated grafting onto fluoro polymers for membrane preparation II

A study has been made for the preparation of membranes by the post radiation grafting of acrylamide (AAm) onto poly(tetrafluoroethylene) (PTFE), films. The appropriate reaction conditions were selected under which the graft polymerization was carried out successfully. In this grafting system ammonium ferrous sulphate (Mohr's salt) was used as inhibitor to minimize the homopolymerization of AAm and a suitable concentration of the inhibitor to be added to the reaction medium was found to be 0.05 wt%. The effect of monomer concentration, radiation intensity and temperature on the rate and final degree of grafting was investigated. Increasing grafting temperature rises the initial grafting rate, whereas the final grafting yield increases with temperature up to 45°C, and then declines. This behaviour was described by the influence of glass transition on the rate of termination in the semicrystalline polymer. The overall activation energy for this grafting system was found to be 14.6 and 44.5 kcal/mol above and below 35°C, respectively. Some selected properties of the graft copolymer were studied. It was found that the grafted membranes possess good mechanical and electrical properties and excellent chemical and thermal stability which makes them very promising in practical applications.     

Grafting onto Starch. IV. Graft Copolymerization of Methyl Methacrylate by Use of AIBN as Radical Initiator

Grafting of poly(methyl methacrylate) onto starch has been investigated in aqueous medium by using AIBN as radical initiator. Starch-g-PMMA has been characterized by determination of starch in the graft copolymer. Percentage of grafting has been determined as functions of concentration of monomer, concentration of initiator, reaction time, and temperature. From scanning electron microscopic studies, evidence for grafting of PMMA onto starch has been presented.     

Grafting of methyl methacrylate onto natural rubber in supercritical carbon dioxide

The grafting of the methyl methacrylate (MMA) monomer onto natural rubber (NR) was carried out by supercritical carbon dioxide (scCO₂) swelling polymerization with benzoyl peroxide (BPO) as an initiator. Fourier transform–infrared spectroscopy (FT–IR) was used to confirm the formation of graft copolymers with the characteristic bands of symmetric C?O and C? O? C stretching vibrations at 1728 cm^?1 and 1147 cm^?1, respectively. The effects of the rubber‐to‐monomer ratio, amount of initiator, reaction time, and pressure on the monomer grafting level (GL) and grafting efficiency (GE) were investigated, and the optimum conditions for the preparation of NR‐g‐MMA were found to be 70:30 of the rubber‐to‐monomer ratio, 1.2% of the initiator content, and the reaction pressure of 23 MPa for 6 h. The thermal behavior of the NR and the different NR/MMA molar ratio grafted copolymer samples was studied by differential scanning calorimetry (DSC). The observed glass transition temperature (T_g) was consistent with the GL. The tensile strength, modulus of elasticity, elongation at break, hardness, and oil resistance of graft copolymers were determined and compared with the values of NR and that of polymerization products prepared in traditional toluene solution. The results showed that the tensile strength, modulus of elasticity, hardness and oil resistance were greatly improved after modification in scCO₂. Copyright © 2007 John Wiley & Sons, Ltd.     

含噁唑烷酮基团丙烯酰单体在纤维素纤维表面的接枝反应

饮用水的水质状况与人体健康的关系十分密切,但是当前世界上的清洁水资源越来越紧缺．水的处理和净化成为人类健康的重要保障,研制一种经济、简便、实用的水处理的材料具有巨大社会效益和经济效益．     

Graft copolymerization of itaconic acid-methacrylamide comonomers onto poly(ethylene terephthalate) fibers

The graft copolymerization of itaconic acid-methacrylamide (IA-MAAm) comonomers was carried out using benzoyl peroxide as initiator onto poly(ethylene terephthalate) (PET) fibers in an aqueous medium. The grafted fibers were characterized by FTIR, TGA, DSC and SEM analysis. Effect of various parameters on graft yield such as feed composition, feed and initiator concentration, reaction time and temperature were investigated. The graft yield in the presence of MAAm increased because of the synergistic effect of MAAm comonomer. While, the graft yield alone with the IA onto PET fiber was 2.2%, the use of MAAm as a comonomer increased the amount of IA introduced to the PET fiber up to 13.7%. The reactivity ratios for both monomers were determined by using a Fineman-Ross plot. The grafting rate and saturation graft yield was increased upon increasing the temperature between 65 °C and 85 °C. When the temperature increased further than 85 °C, the saturation graft yield decreased. The graft yield has shown an increase up to an initiator concentration of 1.0 × 10⁻² M and slightly decreased. The grafting increased the dyeability with acidic and basic dyes, and moisture absorption capacity but decreased the thermal stability of the fibers.