首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 375 毫秒
1.
Polylactic acid (PLA) and thermoplastic starch (TPS) are known as bio‐based and biodegradable thermoplastic polymers that can be used in different applications owing to their inherent physical and mechanical properties. In order to reduce the higher costs of PLA and tuning its physical and mechanical properties suitable for short life packaging applications, blending of PLA with the TPS, more economical biodegradable polymer, has been considered in academic and industrial researches. However, melt blending of PLA with TPS without compatibilization process caused some drawbacks such as coarsening morphology and declining mechanical properties and ductility because of thermodynamic immiscibility, which may restrict its usage in packaging applications. Subsequently, our approach in this research is compatibilization of PLA/TPS blends by utilization of primary well tuning of TPS formulation with a combination of sorbitol and glycerol plasticizers. In this work, the wide composition range of melt mixed PLA/TPS blends was prepared using a laboratory twin screw extruder. The effects of microstructure on the rheological and mechanical properties of PLA/TPS blends were studied using different methods such as scanning electron microscopy (SEM) images, contact angle, oscillatory shear rheological measurements, and tensile and impact strength mechanical tests. The rheological and mechanical properties were interpreted according to the morphological features and considering the possibility of plasticizer migration from TPS to PLA phase during melt blending. Reduction in complex viscosity and storage modulus of PLA matrix samples indicates the improved melt processability of blends. Finally, in comparison with mechanical results reported in literature, our simple approach yielded the blends with elastic modulus and ductility comparable with those of chemically compatibilized PLA/TPS blends.  相似文献   

2.
Blends with varied ratio of polylactic acid (PLA) and thermoplastic polyurethane (TPU) were prepared by melt blending. The PLA content in blends was 20, 40, 60 and 80 wt%. Samples of pure PLA and TPU that underwent the same thermal treatment were also prepared. Biodegradation was examined by respirometry. Pure TPU started to degrade immediately due to degradation of the low molecular weight plasticizer in the polymer. Pure PLA, on the other hand, exhibited an incubation period after which degradation progressed rapidly and was almost complete after 70 days. The degradation profile of the blends can be correlated to their morphology. Samples with a co-continuous morphology initially degrade at a higher rate than the rest of the samples due to the higher exposure of the TPU phase in these blends.  相似文献   

3.
Poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable aliphatic polyesters, which being semicrystalline and thermoplastic can be processed by conventional methods. Their blends give interesting materials for industrial packaging applications, due to their increased ductility as PBAT content increases. However, like many aliphatic polyesters, the PLA matrix degrades upon melt processing thus affecting the thermo-mechanical features of the blended material. In this work, we studied the effect of processing at high temperature on the molecular weight distribution, morphology, and thermo-mechanical properties of both homopolymers, as well as the PLA/PBAT 75/25 blend. Notably, different processing conditions were adopted in terms of temperature (range 150-200 °C) and other relevant processing parameters (moisture removal and nitrogen atmosphere). Analysis of PLA/PBAT blends indicated that intermolecular chain reactions took place under strong degradative conditions of PLA, yielding PLA/PBAT mixed chains (copolymers). Increasing amounts of copolymers resulted in improved phase dispersion and increased ductility, as SEM and mechanical tests indicated. Conversely, reduced PLA degradation with less copolymer formation, afforded higher modulus materials, owing to poorer dispersion of the soft phase (PBAT) into the PLA matrix.  相似文献   

4.
Polylactide (PLA) being a very brittle biopolymer could be toughened by blending with thermoplastic elastomers such as thermoplastic polyurethane elastomer (TPU) and thermoplastic polyester elastomer (TPE); unfortunately, these blends are immiscible forming round domains in the PLA matrix. Therefore, the purpose of this study was to investigate the effects of using maleic anhydride (MA) compatibilization on the toughness and other properties of PLA blended with TPU and TPE. MA grafting on the PLA backbone (PLA‐g‐MA) was prepared separately by reactive extrusion and added during melt blending of PLA/thermoplastic elastomers. IR spectroscopy revealed that MA graft might interact with the functional groups present in the hard segments of TPU and TPE domains via primary chemical reactions, so that higher level of compatibilization could be obtained. SEM studies indicated that PLA‐g‐MA compatibilization also decreased the size of elastomeric domains leading to higher level of surface area for more interfacial interactions. Toughness tests revealed that Charpy impact toughness and fracture toughness (KIC and GIC) of inherently brittle PLA increased enormously when the blends were compatibilized with PLA‐g‐MA. For instance, GIC fracture toughness of PLA increased as much as 166%. It was also observed that PLA‐g‐MA compatibilization resulted in no detrimental effects on the other mechanical and thermal properties of PLA blends. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

5.
Abstract

The aim of this review is to show the relationships between the structure, the process, and the properties of biodegradable multiphase systems based on plasticized starch (PLS), the so‐called “thermoplastic starch.” These mutiphase materials are obtained when associating association between plasticized starches and other biodegradable materials, such as biodegradable polyesters [polycaprolactone (PCL), polyhydroxyalkanoates (PHAs), polylactic acid (PLA), polyesteramide (PEA), aliphatic, and aromatic copolyesters], or agro‐materials (ligno‐cellulosic fiber, lignin etc.). Depending on materials (soft, rigid) and the plastic processing system used, various structures (blends, composites, multilayers) can be obtained. The compatibility problematic between these hetero‐materials is analyzed. These starchy products show some interesting properties and have some applications in different fields: packaging, sports, catering, agriculture and gardening, or hygiene.  相似文献   

6.
Biopolymers represent an interesting class of polymers whose potential is not yet been fully realised. However, more recently, biopolymers are gaining impetus in the market. Among the biopolymers, polylactic acid (PLA) is being used successfully and is widely accepted because it is produced from natural raw material and is degradable. Furthermore, it has comparable properties to standard thermoplastic polymers and can also be processed using similar process channels as conventional thermoplastic synthetic materials. Biopolymer applications are manifold and range from foils, fruit and vegetable packaging to hygiene and medical products. It can be expected that in future the application spectrum of biopolymers will increase even further.  相似文献   

7.
Plasticized polylactide (PLA) – layered silicate nanocomposites were obtained by melt blending PLA with polyethylene glycol as plasticizer (20 wt %) and with different montmorillonite fillers: Cloisite® 20A, Cloisite® 25A, and Cloisite® 30B (from 1 to 10 wt %). Comparative samples of melt‐blended polylactide (without filler) and plasticized PLA with 20 wt % PEG were considered as well. Samples have been aged for 1 and 4 years and their chemical and physical characteristics were compared with not aged reference ones. It was found that molecular weight of the PLA decreased upon melt‐processing and aging, particularly when the Cloisite content increased, without a clear relation to the nature of the organo‐modifier. On the contrary, the PEG plasticizer was practically undegraded upon melt processing and aging. Structural studies revealed that plasticized PLA and plasticized PLA‐based nanocomposites are unstable in time of aging and undergo deplasticization. They showed, after aging, the presence of a thin PEG crystalline layer at the surface of the samples and improved the order in the PLA matrix to a higher extent in plasticized polylactide than in plasticized nanocomposite (due to clay stabilization effect). The amount of PEG diffusing toward sample surface was correlated with aging time, molecular weight of PLA matrix, and Cloisite® type, in clear relation to the extent of intercalation with PLA and PEG. Some modifications of the viscoelastic properties of PLA matrix, induced by the presence of both the nanoparticlate filler and the plasticizer, as well as a deterioration of the mechanical properties upon aging were observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 312–325, 2006  相似文献   

8.
张会良 《高分子科学》2015,33(12):1702-1712
Poly(propylene carbonate)(PPC) was blended with polylactide(PLA) and poly(1,2-propylene glycol adipate)(PPA) using a twin screw extruder. Then the PPC/PLA/PPA films were prepared using the blown film technique. DMA results showed that PPA could act as a plasticizer and improve the miscibility between PPC and PLA. Crystal morphology displayed that blending PLA with the amorphous PPC led to a decrease of the spherulite size of PLA. The results of mechanical tests indicated that PPC-rich films showed high elongation at break and PLA-rich films showed high tear strength and good optical properties. The content of PPC and PLA significantly affected the physical properties of the films. With increasing PPC content, the melt strengths of the PPC/PLA/PPA films were enhanced. These findings contributed to the biodegradable materials application for designing and manufacturing polymer packaging.  相似文献   

9.
Preparing a polylactide (PLA)/plasticizer system has been regarded as an effective solution to improve the ductility of brittle PLA. In this reach, a novel type of alkyl phosphine oxides consisting of three aliphatic ester substituents was prepared from PH3 tail gas, and its potential to be employed as a PLA plasticizer was studied. Differential scanning calorimeter tests confirmed that the newly-prepared plasticizer decreased the Tg of PLA (28 wt% plasticizer) from 52°C (neat PLA) to 11°C, and increased the elongation at break from 11% (neat PLA) to 271% (plasticized PLA). X-ray diffraction results showed that the crystallization degree of PLA (28 wt% plasticizer) increased from 0.12% of neat PLA to 14.04%, while Young's modulus of PLA remained as high as 121.3 MPa, which was much higher than that of the PLA/citrate ester systems with same plasticizer content. These novel phosphorus-containing plasticizers exhibited excellent thermal stability and a weight-loss of the system no more than 2.5% at 180°C; therefore, no unpleasant volatiles were released during processing. In contrast, the weight loss of the PLA/citrate system was as high as 10.8% at 180°C, forming heavy fog with an unpleasant smell during thermal mixing. Scanning electron microscopy was employed to observe the microstructure of the PLA/plasticizer systems, which indicated that the carboxylic butyl ester-containing phosphine oxides was compatible with PLA matrix.  相似文献   

10.
Starting from calcium sulfate (gypsum) as fermentation by‐product of lactic acid production process, high performance composites have been produced by melt‐blending polylactide (PLA, L/D isomer ratio of 96:4) and β‐anhydrite II (AII) filler, that is, calcium sulfate hemihydrate previously dehydrated at 500 °C. Characterized by attractive mechanical and thermal properties due to good filler dispersion throughout the polyester matrix, these composites are interesting for potential use as biodegradable rigid packaging. Physical characterization of selected composites filled with 20 and 40 wt % AII has been performed and compared to processed unfilled PLA with similar amorphous structure. State of dispersion of the filler particles and interphase characteristic features have been investigated using light microscopy (LM) and scanning electron microscopy (SEM). Addition of AII did not decrease PLA thermal stability as revealed by thermogravimetry analyses (TGA) and allowed reaching a slight increase of PLA crystallizability during melt crystallization and upon heating from the glassy, amorphous state (DSC). It was found by thermomechanical measurements (DMTA) that the AII filler increased pronouncedly storage modulus (E′) of the composites in comparison with PLA in a broad temperature range. The X‐ray investigations showed stable/unchanged crystallographic structure of AII during processing with molten PLA and in the composite system. The notable thermal and mechanical properties of PLA–AII composites are accounted for by the good filler dispersion throughout the polyester matrix confirmed by morphological studies, system stability, and favorable interactions between components. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2770–2780, 2007  相似文献   

11.
This research work reports the potential of maleinized linseed oil (MLO) as biobased compatibilizer in polylactide (PLA) and a thermoplastic elastomer, namely, polystyrene-b-(ethylene-ran-butylene)-b-styrene (SEBS) blends (PLA/SEBS), with improved impact strength for the packaging industry. The effects of MLO are compared with a conventional polystyrene-b-poly(ethylene-ran-butylene)-b-polystyrene-graft-maleic anhydride terpolymer (SEBS-g-MA) since it is widely used in these blends. Uncompatibilized and compatibilized PLA/SEBS blends can be manufactured by extrusion and then shaped into standard samples for further characterization by mechanical, thermal, morphological, dynamical-mechanical, wetting and colour standard tests. The obtained results indicate that the uncompatibilized PLA/SEBS blend containing 20 wt.% SEBS gives improved toughness (4.8 kJ/m2) compared to neat PLA (1.3 kJ/m2). Nevertheless, the same blend compatibilized with MLO leads to an increase in impact strength up to 6.1 kJ/m2, thus giving evidence of the potential of MLO to compete with other petroleum-derived compatibilizers to obtain tough PLA formulations. MLO also provides increased ductile properties, since neat PLA is a brittle polymer with an elongation at break of 7.4%, while its blend with 20 wt.% SEBS and MLO as compatibilizer offers an elongation at break of 50.2%, much higher than that provided by typical SEBS-g-MA compatibilizer (10.1%). MLO provides a slight decrease (about 3 °C lower) in the glass transition temperature (Tg) of the PLA-rich phase, thus showing some plasticization effects. Although MLO addition leads to some yellowing due to its intrinsic yellow colour, this can contribute to serving as a UV light barrier with interesting applications in the packaging industry. Therefore, MLO represents a cost-effective and sustainable solution to the use of conventional petroleum-derived compatibilizers.  相似文献   

12.
Two novel biodegradable copolymers, including poly(ethylene glycol)-succinate copolymer (PES) and poly(ethylene glycol)-succinate-l-lactide copolymer (PESL), have been successfully synthesized via melt polycondensation using SnCl2 as a catalyst. The copolymers were used to toughen PLA by melt blending. The DSC and SEM results indicated that the two copolymers were compatible well with PLA, and the compatibility of PESL was superior to that of PES. The results of tensile testing showed that the extensibility of PLA was largely improved by blending with PES or PESL. At same blending ratios, the elongation at break of PLA/PESL blends was far higher than that of PLA/PES ones. The elongation maintained stable through aging for 3 months. The moisture absorption of the blends enhanced due to the strong moisture absorption of PEG segments in PES or PESL molecules, which did not directly lead to enhance the hydrolytic degradation rate of the PLA. The PLA blends containing 20–30 wt% PES or PESL were high transparent materials with high light scattering. The toughening PLA materials could potentially be used as a soft biodegradable packaging material or a special optical material.  相似文献   

13.
ABSTRACT

The role of di-cumyl peroxide (DCP) as compatibilizer in low density Polyethylene/Polypropylene (LDPE/PP) blends has been explored. Mixtures with varying LDPE/PP ratio were prepared in a Brabender plasticorder and tested for their mechanical properties and calorimetric response. Then peroxide was added at concentrations up to 0.5%, and the mechanical properties of the these new blends were measured. Also, the mixing torque, melt flow index and gel content of the above products were recorded as a function of peroxide concentration. It was found that the incorporation of DCP restricts the thermoplastic characteristics of the melt, which was primarily attributed to branching which occurs in LDPE. This results in an enhancement in the adhesive bonding between the two polymers mainly due to chain entanglements. This was further supported by the fact that mechanical properties of the treated blend were significantly improved.  相似文献   

14.
This work focuses on satisfactorily toughening and reinforcing poly(lactic acid)/thermoplastic polyurethane (PLA/TPU) blend with low TPU content (10 wt%) using appropriate amounts of hydrophobic silica nanoparticles (SiO2) via simple melt mixing. Both thermodynamic prediction and transmission electron microscopy micrographs demonstrate that most SiO2 nanoparticles distribute at interfaces between the PLA and TPU phases. This improves interfacial adhesion between the phases, which is attributed to good bonding strength between the PLA and SiO2 via hydrophobic interaction and formation of hydrogen bonds between the TPU and SiO2. The PLA/TPU (90/10) ternary blend nanocomposite with 2 wt% SiO2 exhibits obviously high impact strength (about 5.0 and 12.6 times that of the corresponding blend and PLA, respectively) and higher tensile strength than the blend and even the PLA. Crazing is the main reason for improved impact toughnesses of the blend nanocomposites. This work provides a simple and effective strategy to endow PLA/elastomer blends with optimum strength–toughness balance by adding appropriate amounts of nanoparticles.  相似文献   

15.
New plasticization ways based on low molecular plasticizers from citrates family were investigated to improve the ductility of poly(lactide) (PLA). Grafting reactions between anhydride-grafted PLA (MAG-PLA) copolymer with hydroxyl-functionalized citrate plasticizer, i.e. tributyl citrate (TbC), were so-carried out through reactive extrusion. TributylO-acetylcitrate (ATbC) was used as a non-functionalized reference. Both plasticizers drastically decreased the Tg of PLA. However, the grafting reaction of TbC into MAG-PLA revealed a shift of PLA Tg toward higher values. After 6 months of aging, no phase separation was observed. However, plasticizer leaching was noticed in the case of PLA/ATbC materials, leading to the shift of Tg toward lower temperatures. In contrast, no major leaching phenomenon was noticed in PLA/TbC and PLA/MAG-PLA/TbC blends, indicating that the mobility restriction derived from the hydrogen bonding that can occur between PLA and TbC as well as the grafting reaction of TbC into MAG-PLA enabled to reduce leaching phenomena.  相似文献   

16.
《先进技术聚合物》2018,29(7):2121-2133
Polylactide (PLA)/poly(butylene succinate) (PBS) blend films modified with a compatibilizer and a plasticizer were hot‐melted through a twin screw extruder and prepared by hydraulic press. Toluene diisocyanate (TDI) and polylactide‐grafted‐maleic anhydride (PLA‐g‐MA) were used as compatibilizers, while triethyl citrate and tricresyl phosphate acted as plasticizers. The effects of the type and content of compatibilizer and plasticizer on the mechanical characteristics, thermal properties, crystallization behavior, and phase morphology of the PLA/PBS blend films were investigated. Reactive compatibilization at increasing levels of TDI improved the compatibility of the PLA and PBS, affecting the toughness of the films. As evidenced by scanning electron microscope, the addition of TDI enhanced the interfacial adhesion of the blends, leading to the appearance of many elongated fibrils at the fracture surface. Furthermore, PLA/PBS blending with both TDI and PLA‐g‐MA led to an acceleration of the cold crystallization rate and an increment of the degree of crystallinity ( ). Toluene diisocyanate could be a more effective compatibilizer than PLA‐g‐MA for PLA/PBS blend films. The synergistic combination of compatibilizer and plasticizer brought a significant improvement in elongation at break and tensile‐impact toughness of the PLA/PBS blends, compared with neat PLA. Their failure mode changed from brittle to ductile due to the improved compatibility and molecular segment mobility of the PLA and PBS phases. Differential scanning calorimeter results revealed that the plasticizers triethyl citrate and tricresyl phosphate changed the thermal behavior of Tcc and Tm, affecting α′ and α crystal formations. However, these plasticizers only slightly improved the thermal stability of the films.  相似文献   

17.
聚乳酸(PLA)是目前合成生物可降解高分子材料中应用量最大的品种,可望逐渐部分取代聚烯烃而更广泛应用于各个领域。但PLA树脂结构决定的松弛特性导致其加工过程特殊的黏弹特性,使其熔体强度低、成型工艺特性不稳定并进而导致产品尺寸和性能不稳定。此外,PLA极低的结晶速率,使其在挤出和注射成型等较高冷却速率的实际加工条件下呈无定型态,进一步影响了其加工和使用性能。这些问题已成为PLA更大规模商品化应用的瓶颈。本文从通过调控PLA熔体加工过程的黏弹特性而提高其可加工性出发,综述近年来本课题组在PLA成型加工过程中熔体粘弹特性和结晶行为(结晶速率和结晶结构)调控方面的研究进展。  相似文献   

18.
The novel film structure of corn-zein coated on polypropylene (PP) synthetic film for packaging industry was developed to examine the feasibility of resulting coated films as an alternative water barrier performance for food packaging. The effects of coating formulation (solvent, corn-zein, plasticizer concentration and plasticizer type) on final properties of films were observed. Corn-zein is the most important protein of corn and has good film forming property. Composites structures of PP films coated with corn-zein were obtained through a simple solvent casting method. Polyethylene glycol (PEG) and glycerol (GLY) were used as plasticizer to increase film flexibility. Statistical analysis based on full factorial design was performed to observe coating formulation effects. The high water vapour barriers were obtained for films coated with coating formulation consisting of higher amounts of corn-zein plasticized by GLY. The lower glass transition temperatures (T g) of films were obtained by plasticization of films and T g decreased by increasing plasticizer content. The statistical analysis defined the key parameters of coating formulation that had major effects on the final properties of coated PP films as corn-zein, plasticizer concentration and plasticizer type. In conclusion, corn-zein coatings could have potential as an alternative to conventional synthetic polymers used in composite multilayer structures for food packaging applications.  相似文献   

19.
The academic and industrial aspects of the preparation, characterization, mechanical and materials properties, crystallization behavior, melt rheology, and foam processing of pure polylactide (PLA) and PLA/layered silicate nanocomposites are described in this feature article. Recently, these materials have attracted considerable interest in polymer science research. PLA is linear aliphatic thermoplastic polyester and is made from agricultural products. Hectorite and montmorillonite are among the most commonly used smectite‐type layered silicates for the preparation of nanocomposites. Smectites are a valuable mineral class for industrial applications because of their high cation exchange capacities, surface area, surface reactivity, adsorptive properties, and, in the case of hectorite, high viscosity, and transparency in solution. In their pristine form, they are hydrophilic in nature, and this property makes them very difficult to disperse into a polymer matrix. The most common way to overcome this difficulty is to replace interlayer cations with quaternized ammonium or phosphonium cations, preferably with long alkyl chains. In general, polymer/layered silicate nanocomposites are of three different types: (1) intercalated nanocomposites, in which insertion of polymer chains into the layered silicate structure occurs in a crystallographically regular fashion, regardless of polymer to layered silicate ratio, with a repeat distance of few nanometer; (2) flocculated nanocomposites, in which intercalated and stacked silicate layers are sometimes flocculated due to the hydroxylated edge–edge interactions between the silicate layers; (3) exfoliated nanocomposites, in which individual silicate layers are uniformly distributed in the polymer matrix by average distances that totally depend on the layered silicate loading. This new family of composite materials frequently exhibits remarkable improvements in its material properties when compared with those of virgin PLA. Improved properties can include a high storage modulus both in the solid and melt states, increased flexural properties, a decrease in gas permeability, increased heat distortion temperature, an increase in the rate of biodegradability of pure PLA, and so forth.

Illustration of the biodegradability of PLA and various nanocomposites.  相似文献   


20.
In this work, the modification process of poly(lactic acid) (PLA) with metal-based nanoparticle (NPs) additives (Ag, ZnO, TiO2) at different loading (0.5, 1.0, and 2.5 wt%) and by melt-mix extrusion method followed by film formation as one of the advantageous techniques for industrial application have been investigated. PLA nanoparticle composite films (PLA-NPs) of PLA-Ag, PLA-ZnO, PLA-TiO2 were fabricated, allowing convenient dispersion of NPs within the PLA matrix to further pursue the challenge of investigating the surface properties of PLA-NPs reinforced plastics (as films) for the final functional properties, such as antimicrobial activity and surface mechanical properties. The main objective was to clarify how the addition of NPs to the PLA during the melt extrusion process affects the chemistry, morphology, and wettability of the surface and its further influence on the antibacterial efficiency and mechanical properties of the PLA-NPs. Therefore, the effect of Ag, ZnO, and TiO2 NPs incorporation on the morphology (SEM), elemental mapping analysis (SEM-EDX), roughness, surface free energy (SFE) of PLA-NPs measured by goniometry and calculated by OWRK (Owens, Wendt, Rabel, and Kaelble) model was evaluated and correlated with the final functional properties such as antimicrobial activity and surface mechanical properties. The developed PLA-metal-based nanocomposites, with improved mechanical and antimicrobial surface properties, could be used as sustainable and biodegradable materials, offering desirable multifunctionalities not only for food packaging but also for cosmetics and hygiene products, as well as for broader plastic products where antimicrobial activity is desirable.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号