Poly(enamine-ketones) from hydrogen-terminated aromatic dipropynones and aromatic diamines

Poly(enamine-ketones) were prepared by the nucleophilic (Michael-type) addition of various aromatic diamines to 1,1′-(1,3- or 1,4-phenylene)bis(2-propyn-1-one)(1,3 or 1,4-PPO) in m-cresol at 5–23°C. The low molecular weight polymers (inherent viscosity of 0.25 dL/g) exhibited limited solubility in organic solvents. Glass transition temperatures were generally undetectable by differential scanning calorimetry while polymer decomposition temperatures (10% weight loss), as measured by thermogravimetric analysis, were observed from 355 to 419°C. Polymers prepared from 1,4-PPO were semi-crystalline as shown by wide-angle X-ray diffraction. The poly(enamine-ketone) structure was confirmed by matching infrared spectral characteristics of the polymers with those of well-characterized model enamine ketones.     

Synthesis and Characterization of Polymers Derived from the Copolymerization of 1,1′-Dihydroxyethyl-2,2′-Biimidazole and the Diglycidyl Ether of Bisphenol A

Abstract

1,1′-Dihydroxyethyl-2,2′-biimidazole has been used as a copolymerizing monomer with the diglycidyl ether of bisphenol A in the preparation of biimidazole-containing epoxy polymers. Polymerization reactions were studied in bulk, with and without catalyst, and in N,N-dimethylforma-mide and anisole solvents, with and without catalyst. FT-IR and NMR spectra, molecular weight, thermal and solubility characteristics were obtained. Polymers isolated as amorphous light brown solids were found to be only sparingly soluble in THF or in highly polar nitrogen-containing solvents (DMF, NMP, pyridine). These materials exhibited molecular weights up to 37 000 for SnC1₄-catalyzed polymerization carried out in DMF. A glass-transition temperature of 391°C was observed for polymers obtained under uncatalyzed solventless conditions. The glass transition temperature was 373°C for product obtained under SnC1₄-catalyzed, solventless conditions. Thermogravimetric analysis in air of polymers obtained under varying solvent and catalyst conditions showed less than 25% weight loss below 330°C and greater than 75% weight loss above 400°C.     

Ring-opening polymerization of 1,5-dioxepan-2-one initiated by a cyclic tin–alkoxide initiator in different solvents

Ring-opening polymerization of 1,5-dioxepan-2-one initiated by 1,1,6,6-tetra-n-butyl-1,6-distanna-2,5,7,10-tetraoxacyclodecane was carried out in chloroform, dichloromethane, or 1,2-dichloroethane. Effects of reaction temperature, solvent, and monomer-to-initiator ratio were investigated. Polymerization kinetics showed a first-order dependence on the monomer for polymerization in chloroform and dichloromethane at 40°C. The kinetic order with respect to the initiator were a first order when dichloromethane was used as the solvent, the order in initiator changed, depending on the initiator concentration when chloroform was used. A maximum in molecular weight was observed at 40°C when chloroform was used as the solvent. The change of solvent did not markedly alter the polymerization rate or the molecular weight of the polymers prepared, as expected from the coordination insertion mechanism. Depolymerization of the polymers formed was observed when the reaction was allowed to continue after complete monomer conversion in chloroform as reaction medium at 40°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3407–3417, 1999     

Cationic Polymerization of 1,5-Dioxepan-2-one with Lewis Acids in Bulk and Solution

Abstract

1,5-Dioxepane-2-one (DXO) was coordinatively ring-opening polymerized with different Lewis acids in bulk and solution. The reactivities of a series of initiators (SnCl₄, FeCl₃, AlCl₃, BCl₃, and BF₃OEt₂) at different temperatures and reaction times were analyzed. Polymerization of DXO in bulk with SnCl₄, FeCl₃, AlCl₃, and BCl₃ gave only oligomers or low molecular weight polymers irrespective of temperature and/or reaction time. Polymerization of DXO with BF₃OEt₂ at 70°C gave yields of nearly 100% and molecular weights up to M _w = 10,000. The polymerization temperature was increased to 100°C and the reaction time prolonged, which resulted in nearly equal molecular weights as at 70°C but with lower yields, higher polydispersity, and generally not full conversion. In addition, side reactions, such as backbiting, transesterification and thermal degradation, occurred to a larger extent at higher reaction temperatures. Solution polymerization using the same initiators and THF, dioxane, or nitrobenzene as the solvent gave polymers of low molecular weights and of low yields, except with FeCl₃ and BF₃OEt₂. The rates of polymerization were significantly higher in nitrobenzene than in dioxane and THF due to polarity and coordination of these solvents to the growing chain. Comparison of the initiators BF₃OEt₂ and SnCl₄ in solution polymerization showed equal reactivity in nitrobenzene for both of them. The BF₃OEt₂-initiated systems give polymers with lower molecular weights than SnCl₄-initiated systems, but with narrower polydispersity.     

Association of polyacrylonitrile prepared by low-temperature,solution polymerization with an organometallic catalyst

The weight-average molecular weights of polymers of acrylonitrile prepared by a free-radical initiator and an organometallic catalyst have been determined by lightscattering measurements in N,N-dimethylformamide, dimethyl sulfoxide, and dimethylacetamide at 25°C. and in dimethyl sulfoxide at 140°C. The apparent molecular weights of the polymers prepared with the NaAlEt₃S(i-Pr) catalyst in DMF at ?78°C. (referred to as high-melting polymers) changed from 54,800, 82,700, and 480,000 when measured in DMF at 25°C. to 36,000, 41,600, and 225,000 when measured in DMSO at 140°C., whereas the molecular weights of the free-radical polymers remained unchanged. Furthermore, from results obtained in DMSO at 140°C., The intrinsic viscosity–molecular-weight relationships were found to be identical for the high-melting and the free-radical polymer and in substantial agreement with an equation reported by Cleland and Stockmayer. The apparent decrease in molecular weight of the high-melting polymer from 25 to 140°C. indicates rather clearly that the high-melting polymers are associated in DMF at 25°C. The “aggregates,” even though present only at low concentrations, raised the weight-average molecular weight markedly but affected the number-average molecular weight only slightly, thus giving a high M?_w/M?_n ratio. It appears likely that when temperature and solvent are such that association does not occur, linear PAN's will have approximately the same intrinsic viscosity–molecular weight relationship (subject of course to slight change by polydispersity). The often reported abnormal molecular weight of samples prepared by solution polymerization especially at low temperatures, may be attributed to branching, or to an association, as reported here. The nature of association of PAN in dilute solution is also discussed.     

Linear and Hyperbranched Poly(arylene ether)s from a New Semifluorinated AB Monomer

A new trifluoromethyl-activated AB monomer has been successfully synthesized by Pd-initiated coupling of 4-bromo anisole with 4-fluoro-3-trifluoromethylphenylboronic acid followed by demethylation. The monomer leads to a semifluorinated poly(arylene ether) by nucleophilic displacement polymerization reaction. The AB monomer has been further copolymerized with a corresponding AB ₂ monomer to form the corresponding semifluorinated hyperbranched (hb) poly(arylene ether). The resulting linear and hb poly(arylene ether)s exhibited weight average molecular weight of 75700 and 144100 g/mol, respectively. The hb copolymer exhibited better solubility in different organic solvents compared to the linear poly(arylene ether). The polymers showed excellent thermal stability up to 522°C at 10% wt loss in air and glass transition temperatures as high as 187°C. The mechanical properties of the linear poly(arylene ether) film 1a exhibited tensile strength at break of 89 MPa, elongation at break of up to 3% and a Young’s modulus value of 2.66 GPa. The films of the polymers were hydrophobic in nature and showed water contact angle as high as 93.6°.     

Living cationic polymerization of 2-vinyloxyethyl phthalimide: Synthesis of poly(vinyl ether) with pendant primary amino functions

Cationic polymerization of 2-vinyloxyethyl phthalimide ( 1 ) in CH₂Cl₂ at ?15°C with hydrogen iodide/iodine (HI/I₂) as initiator led to living polymers of a narrow molecular weight distribution (M?_w/M?_n = 1.1–1.25). The number-average molecular weight of the polymers was in direct proportion to monomer conversion and could be controlled in the range of 1000–6000 by regulating the 1 /HI feed ratio. However, when a fresh monomer was supplied to the completely polymerized reaction mixture, the molecular weight of the polymers was not directly proportional to monomer conversion. The polymerization of 1 by boron trifluoride etherate (BF₃OEt₂) in CH₂Cl₂ at ?78°C gave polymers with relatively high molecular weight (M?_w > 20,000) and broad molecular weight distribution (M?_w/M?_n ～ 2). The HI/I₂-initiated polymerization of 1 was an order of magnitude slower than that of ethyl vinyl ether, probably because of the electron-withdrawing phthalimide pendant. Hydrazinolysis of the imide functions in poly( 1 ) gave a water-soluble poly(vinyl ether) ( 3 ) with aliphatic primary amino pendants.     

Poly(Aryl Ether)s from a Novel Biphenol Monomer Containing a Dicyanoarylene Group

Abstract

The preparation of a novel biphenol, 1,4-bis(4-hydroxyphenyl)-2,3-dicyanonaphthalene, from phenolphthalein is described. This biphenol was prepared in high yield in a four-step reaction sequence. The biphenol can be polymerized with activated dihalides such as 1,2-bis-(4-fluorobenzoyl)-3,4,5,6-tetraphenylbenzene, bis(4-fluorophenyl) sulfone, and 4,4′-dichlorobenzophenone to give high molecular weight amorphous poly(aryl ether)s. The polymers have glass transition temperatures ranging from 284 to 319°C and are easily cast into flexible, colorless, and transparent films. The 5% weight loss temperatures of these polymers, by thermogravimetric analysis in air and nitrogen, are all above 500°C.     

Synthesis of norbornenes containing cationic mono‐ and di(cyclopentadienyliron)arene complexes and their ring‐opening metathesis polymerization

A number of classes of polynorbornenes containing cationic iron moieties within their side chains were prepared via ring‐opening metathesis polymerization with a ruthenium‐based catalyst. The iron‐containing polymers displayed excellent solubility in polar organic solvents. The weight‐average molecular weights of these polymeric materials were estimated to be in the range of 18,000–48,000. Thermogravimetric analysis of these polymers showed two distinct weight losses. The first weight loss was in the range of 204–260 °C and was due to the loss of the metallic moieties, whereas the second weight loss was observed at 368–512 °C and was due to the degradation of the polymer backbone. Cyclic voltammetry studies of the iron‐containing polymers showed that the 18 e^? cationic iron centers underwent a reduction to give the neutral 19 e^? complexes at half‐wave potential (E_1/2) = ?1.105 V. Photolysis of the metallated polymers led to the isolation of the norbornene polymers in very good yields. Differential scanning calorimetry studies showed a sharp increase in the glass‐transition temperatures up to 91 °C when rigid aromatic side chains were incorporated into the norbornene polymers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3053–3070, 2006     

Characterization of Branched Poly (vinyl Acetate) by GPC and Low Angle Laser Light Scattering Photometry

Abstract

Poly (vinyl acetate), PVAC, synthesized by bulk polymerization over a range of initiator concentrations ([AIBN] = 10^?5 to 4 × 10^?3 g-mole/1), temperatures (50°C, 60°C, 70°C, and 80°C) and conversion levels (3 to > 90%) were characterized using low angle laser light scattering (LALLS) photometry to measure M_w of the whole polymers. A number of these samples were characterized using GPC with a differential refractive index (DRI) and LALLS detector to measure the molecular weight distribution (weight fraction versus M_w). M_w for PVAC samples synthesized at suitably low initiator levels at various conversions were found to agree with classical light scattering measurements after Graessley.

An electronic device and a technique which optimizes the sensitivity and the signal-to-noise ratio of the LALLS photometer throughout the molecular weight distribution (MWD) of the GPC chromatogram were devised. These considerably simplify the operation of the LALLS for both offline and online operation with GPC.

Most importantly it was unambiguously shown that the commonly used universal calibration parameter (UCP) with GPC, [n]M_w, is incorrect for polymers with molecules having the same hydrodynamic volume but different molecular weights, i. e., those with only chain branching (LCB), copolymers with compositional drift, and polymer blends. The correct UCP was found to     

Molecular weight distribution and stereoregularity of polypropylenes produced with VCl4–AlEt2Cl catalyst

Dependences of the molecular weight distribution and stereochemical regulation of the polypropylenes produced with VCl₄–AlEt₂Cl catalyst on the polymerization temperature were examined. The molecular weight distributions of the polymers obtained at temperatures below ?40°C were unimodal and narrow (M _w/M _n ≤ 2). The molecular weight distributions obtained at higher temperatures (above ?21°C) were bimodal with one narrow distribution and one wide one (M _w/M _n > 2), and the polymer fraction of the wide distribution increased with the polymerization temperature. The fractional amount of ? (CH₂)₂? groups in the polymers, which corresponds to tail-to-tail linkage of two propylene units, increased to a maximum at ?21°C followed by a gradual decrease with the polymerization temperature. The production of isotactic polymers was confirmed at temperatures above ?21°C. From these data, it is concluded that only the homogeneous form of the catalyst system is responsible for the polymerization at temperatures below about ?21°C while the heterogeneous form appears and catalyzes the polymerization together with the homogeneous one at temperatures above ?21°C.     

Polymerization of Acrylamide in Aqueous Solution of Poly(N‐isopropylacrylamide) at Lower Critical Solution Temperature

Acrylamide (AAm) was found to polymerize in a solution of poly(N‐isopropylacrylamide) (PNIPAAm) in water at around its lower critical solution temperature (LCST) (32°C) without any initiators. This phenomenon was specifically observed in aqueous solutions of the polymers having LCST such as PNIPAAm and poly(methylvinylether) (PMVE). AAm polymerized only when PNIPAAm and AAm were dissolved in water below LCST of PNIPAAm and then the solution was warmed up to the polymerization temperature (40°C). On the other hand, the polymerization of AAm did not proceed when AAm was added into aqueous PNIPAAm solution during and after the phase separation above 32°C. Furthermore the polymerizability of AAm was remarkably affected by the concentration and molecular weight of the PNIPAAm additives. Under the condition of lower PNIPAAm concentration (0.30 mol/L), the increase in the molecular weight of PNIPAAm considerably increased the molecular weight of the resulting PAAm but decreased the yield of PAAm. Under the condition of higher PNIPAAm concentration (0.60 mol/L) the polymerizability was not so affected by the molecular weight of PNIPAAm, while the molecular weight of PAAm formed by using higher molecular weight PNIPAAm was higher than those of PAAm formed by using lower molecular weight PNIPAAm. Moreover, the molecular weight of PAAm formed by the PNIPAAm induced polymerization of AAm was much higher than that of the polymer obtained by the radical polymerization using AIBN in THF or VA‐ 061 in water.     

Unusual effect of molecular weight and concentration on thermoresponsive behaviors of well‐defined water‐soluble semirigid polymers

A series of water‐soluble semirigid thermoresponsive polymers with well‐defined molecular weights based on mesogen‐jacketed liquid crystal polymers (MJLCPs), poly[bis(N‐hydroxyisopropyl pyrrolidone) 2‐vinylterephthalate] (PHIPPVTA) have been synthesized via reversible addition fragmentation chain transfer (RAFT) polymerization. Dynamic light scattering (DLS) revealed that the novel monomer and polymers have thermoresponsive properties with cloud point in the range between 10 and 90 °C. The cloud point was increased by 56.2 °C when the polymer molecular weight increased from 0.47 × 10⁴ g mol^?1 to 3.69 × 10⁴ g mol^?1. In addition, the cloud point of PHIPPVTA was decreased by 18.8 °C with the increase of polymer concentration from 5 to 10 mg mL^?1. A slight increase (0.1–3.5 °C) of cloud point has been observed after knocking off the end‐groups of PHIPPVTA. Moreover, the cloud point of polymer increased with increasing of its molecular weight with or without the trithiocarbonate end‐groups, which showed the opposite trend comparing with other thermoresponsive polymers with flexible backbones. These polymers show a dramatic solvent isotopic effect that the cloud point in D₂O was lower than in H₂O. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Poly(enamine-ketones) from aromatic diacetylenic diketones and aromatic diamines

Novel poly(enamine-ketones) were prepared with inherent viscosities as high as 1.99 dL/g using the Michael-type addition of various diamines to 1,1′-(1,3 or 1,4-phenylene)bis(3-phenyl-2-propyn-1-one) in m-cresol at 60–130°C. Tough, clear, amber films with tensile strengths of 12, 400 psi and tensile moduli of 397, 000 psi were cast from solutions of the polymers in chloroform. The polymers exhibited T_gs as high as 235°C and weight losses of 14% after aging at 232°C in circulating air for 60 h. The synthesis and characterization of several poly(enamine-ketones) are discussed.     

Reversible addition‐fragmentation chain transfer polymerization of methacrylates containing hole‐ or electron‐transporting groups

The controlled/living radical polymerization of 2‐(N‐carbazolyl)ethyl methacrylate (CzEMA) and 4‐(5‐(4‐tert‐butylphenyl‐1,3,4‐oxadiazol‐2‐yl)phenyl) methacrylate (t‐Bu‐OxaMA) via reversible addition‐fragmentation chain transfer polymerization has been studied. Functional polymers with hole‐ or electron‐transfer ability were synthesized with cumyl dithiobenzoate as a chain transfer agent (CTA) and AIBN as an initiator in a benzene solution. Good control of the polymerization was confirmed by the linear increase in the molecular weight (MW) with the conversion. The dependence of MW and polydispersity index (PDI) of the resulting polymers on the molar ratio of monomer to CTA, monomer concentration, and molar ratio of CTA to initiator has also been investigated. The MW and PDI of the resulting polymers were well controlled as being revealed by GPC measurements. The resulting polymers were further characterized by NMR, UV‐vis spectroscopy, and cyclic voltammetry. The polymers functionalized with carbazole group or 1,3,4‐oxadiazole group exhibited good thermal stability, with an onset decomposition temperature of about 305 and 323 °C, respectively, as determined by thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 242–252, 2007     

Producing bimodal molecular weight distribution polymers through facile one‐pot/one‐step RAFT polymerization

Well‐defined bimodal molecular weight distribution (MWD) polystyrene and polystyrene‐b‐poly(acrylonitrile) were successfully synthesized using a pair of mono/difunctional trithiocarbonate RAFT agents 1 and 2 via one‐pot RAFT polymerization. The kinetics of RAFT polymerization for styrene in bulk with a molar ratio of [St]₀:[AIBN]₀:[ 1 ]₀:[ 2 ]₀ = 1200:1:2.5:2.5 was studied at 75°C. The results indicated that the system showed excellent controllability and “living” characteristics to both higher and lower molecular weight fractions, providing an efficient and facile way to producing bimodal MWD (co)polymers with both controlled molecular weight (MW) and MWD in molecular level, and the plausible mechanism was discussed in this work. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Anionic Polymerization of α-Methylstyrene. IX. Nature of the Propagating Species

Abstract

The nature of the initiating and propagating species involved in the anionic polymerization of α-methylstyrene has been explored. The earlier hypothesis that multimodal GPC molecular weight distributions in polymers arise solely out of different reaction steps or different ion-pair mechanisms being involved has been modified for poly-α-methylstyrene. Multimodal GPC molecular weight distributions in poly-α-methylstyrene initiated with potassium at 25°C and polymerized at 25°C or higher in THF, p-dioxane, or cyclohexane as solvents have been ascribed to the presence of two different types of tetramers which grow simultaneously but at different rates, each responding to its own well-defined thermodynamic equilibrium and yielding dormant and living polymers. Reaction schemes describing the initiation (at 25°C) and propagation reactions (between -25 and 60°C) in the polymerization (in solution of THF as well as in bulk) of α-methylstyrene initiated with potassium-naphthalene, butyl-lithium, and butyllithium-tetramethylethylenediamine (TMEDA) have been presented. The role of coordinating agents naphthalene and TMEDA in changing irreversible propagations into reversible ones has been emphasized.     

Improved Flexural Strength of N-Vinyl-Pyrrolidone Modified Acrylic Acid Copolymers for Glass-Ionomers

Abstract

The flexural strengths of N-vinylpyrrolidone modified glass-ionomer cements were investigated. The optimal molar ratio of the monomers in copolymers, composed of the three components acrylic acid, itaconic acid and N-vinylpyrrolidone, was determined using a SAS statistical program. The copolymers were prepared using a free-radical polymerization process. The viscosities of aqueous solutions of these polymers were determined. Cements were formed by the reaction of these solutions with glass particles. Flexural strength (FS) was used as the basic screening property to find the optimum molar ratio. Statistical models were applied to predict the optimum molar ratios. All strength values were recorded on the specimens conditioned in distilled water at 37°C for 7 days. The optimal molar ratio for these copolymers was 7:1:3 for poly(acrylic acid-co-itaconic acid-co-N-vinylpyrrolidone), based on flexural strength and viscosity. The effect of molecular weight (MW) on FS was also evaluated. Copolymer with a MW of 10, 800 (M_n) showed 85% higher FS than the Ketac-Molar (KM) system, along with a reasonable working viscosity.     

New thermally stable condensation polymers containing central ketal moieties derived from malonaldehydetetramethyl acetal and dihydroxyaromatic compounds

Abstract

A number of new condensation polymers with acetal units in the main chain and having linear and ladder-form structure and high thermal stability were synthesized by solution polycondensation of dihydroxyaromatic compounds with malonaldehydetetramethyl acetal as a reactive protected 1,3-dicarbonyl compound. Optimal conditions for polycondensation were obtained via study of the model compounds. In order to obtain high molecular weight polymers, general investigations on the influence of reaction conditions, such as monomer concentration and reaction temperature were carried out. All polymers were obtained in high yields and moderate inherent viscosity ranging from 0.25 to 0.41?dL/g. The proposed chemical structures of condensation polymers were confirmed by ¹H-NMR, ¹³C-NMR, FTIR spectroscopies, TGA, and DSC. Thermal analysis indicated that these polymers are stable up to 360?°C, and a 10% weight loss (T₁₀) were recorded on the TG curves in the temperature range of 381–411?°C in nitrogen atmosphere, indicating their good thermal stability.     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008