The role of pyridine derivatives in living carbocationic polymerization: Lewis base or nucleophile?

The living cationic polymerization of isobutylene induced by the 2-chloro-2,4,4-trimethylpentane/TiCl₄/hexane:methyl chloride (60:40, v:v)/-80°C system was studied in the presence of pyridine derivatives. Protic initiation, substantial in the absence of these additives, was virtually eliminated in their presence, and polyisobutylenes with controlled molecular weight and narrow molecular weight distribution were obtained. With some additives, however, proton elimination occurs, resulting in the exclusive formation of the exo olefin. The rate of elimination is independent of monomer concentration, i.e., it occurs during and after the polymerization. Results suggest that the proton elimination is due to the presence of an uncomplexed base, especially when complex formation with TiCl₄ is hindered by steric compression, but its approach of the polymer cation is not fully blocked.     

Living Carbocationic Polymerization of Styrene in the Presence of Proton Trap

Abstract

The living polymerization of styrene was achieved with the 2,4,4-trimethyl-2-pentyl chloride/TiCl₄/MeCl:methylcyclohexane 40:60 v:v/?80°C polymerization system in the presence of di-tert-butylpyridine in concentrations comparable to the concentration of protic impurities. It was determined that the living nature of the polymerization is not due to carbocation stabilization. The polymerization is second order in TiCl₄. Side reactions, namely polymerization by direct initiation and intermolecular alkylation, are operational, and a careful selection of experimental conditions is necessary to minimize their effect and obtain apparently living behavior. Polymerization by direct initiation can be minimized by increasing the initiator concentration, and intermolecular alkylation can be reduced by quenching the polymerization system when the conversion reaches close to 100%.     

Comparison of the Mechanism and Kinetics of Living Carbocationic Isobutylene and Styrene Polymerizations Based on Real-Time FTIR Monitoring

This paper will compare the mechanism and kinetics of living carbocationic polymerization of isobutylene (IB) and styrene (St), initiated by the 2-chloro-2,4,4-trimethyl-pentane (TMPCl) / TiCl₄) system in 60/40 (v/v) methylcyclohexane / methyl chloride mixed solvent at −80 and −75 °C. The rate of initiation was found to be first order in TiCl₄ in both systems. While initiation is instantaneous in IB polymerization at [TiCl₄]₀ ⩾ [TMPCl]₀, it is slow in St polymerization. Kinetic derivation showed that initiating efficiency is dependent on [M] in this latter system, which was also demonstrated experimentally. The apparent initiation rate constant was determined from initiator consumption rate data and was found to be k_i,app = 1.39 l²/mol²sec. The rate of St consumption measured using a real time fibre-optic mid-FTIR monitoring technique compared well with gravimetric data and was found to be closer to first order in TiCl₄ at [TiCl₄]₀ < [TMPCl]₀. However, the rate followed a close to second order in TiCl₄ at [TiCl₄]₀ ⩾ [TMPCl]₀. The mechanistic model proposed earlier for living carbocationic IB polymerization, which yielded good agreement with experimental data, seems to apply to carbocationic St polymerization as well. This model reconciles the discrepancy between rate constants published for carbocationic IB and St polymerizations, and accounts for shifting TiCl₄ orders. However, independent investigations are necessary to verify the proposed mechanistic model. Optimized conditions led to living carbocationic St polymerization producing high molecular weight PS with 100% initiating efficiency.     

Living carbocationic copolymerization of isobutylene with styrene

The carbocationic copolymerization of isobutylene (IB) and styrene (St), initiated by 2‐chloro‐2,4,4‐trimethylpentane/TiCl₄ in 60/40 (v/v) methyl chloride/hexane at ?90 °C, was investigated. At a low total concentration (0.5 mol/L), slow initiation and rapid monomer conversion were observed. At a high total comonomer concentration (3 mol/L), living conditions (a linear semilogarithmic rate and M_n–conversion plots) were found, provided that the St concentration was above a critical value ([St]₀ ～ 0.6 mol/L). The breadth of the molecular weight distribution decreased with increasing IB concentration in the feed, reaching M_w/M_n ～ 1.1. St homopolymerization was also living at a high total concentration, yielding polystyrene with M_n = 82,000 g/mol, the highest molecular weight ever achieved in carbocationic St polymerization. An analysis of this system by both the traditional gravimetric–NMR copolymer composition method and FTIR demonstrated penultimate effects. IB enrichment was found in the copolymers at all feed compositions, with very little drift at a high total concentration and above the critical St concentration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1778–1787, 2007     

Photo-controlled/living radical polymerization mediated by 2,2,6,6-tetramethylpiperidine-1-oxyl in inert atmospheres

The photo-controlled/living radical polymerization of methyl methacrylate using a nitroxide mediator was established in an inert atmosphere. The bulk polymerization was performed at room temperature using 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl as the mediator and (2RS,2′RS)-azobis(4-methoxy-2,4-dimethylvaleronitrile) as the initiator in the presence of (4-tert-butylphenyl)diphenylsulfonium triflate as the accelerator by irradiation with a high-pressure mercury lamp. The photopolymerization in a N₂ atmosphere produced a polymer with a comparatively narrow molecular weight distribution; however, the experimental molecular weight was slightly different from the theoretical molecular weight. The Ar atmospheric polymerization also provided a polymer with the molecular weight distribution similar to that of the polymer obtained by the N₂ atmospheric polymerization. These inert atmospheric polymerizations more rapidly proceeded to produce polymers with narrower molecular weight distributions than the vacuum polymerization. The livingness of the Ar atmospheric polymerization was confirmed on the basis of the first-order time–conversion plots and conversion–molecular weight plots.     

Sulfonation of tert-alkyl chlorides: Application to the tert-chloride-terminated polyisobutylene system

The direct sulfonation of tert-chloride-terminated polyisobutylene was carried out using acetyl sulfate in methylene chloride/hexanes diluent to produce low molecular weight model ionomer systems with narrow molecular weight distribution. The room temperature sulfonation of 2-chloro-2,4,4-trimethylpentane, which serves as a model for the polyisobutylene chain end obtained in the controlled cationic polymerization of isobutylene, was found to be quantitative after 3 h reaction. The two major products, isomeric β,γ-unsaturated sulfonic acids differing only in the location of the double bond, were the same products obtained from the sulfonation of 2,4,4-trimethyl-1-pentene, which serves as a model for the polyisobutylene chain end after quantitative dehydrochlorination. Near-monodisperse, tert-chloride-terminated, three-arm star polyisobutylene was synthesized under living cationic polymerization conditions using the tricumychloride/TiCl₄/pyridine initiation system in hexanes/methyl chloride consolvents. Sulfonation was carried out directly upon the obtained polymer, and the sulfonated product was purified using ion-exchange chromatography. Structural elucidation was performed using NMR. Titration and molecular weight characterization revealed that sulfonation produced exactly one sulfonic acid group per polyisobutylene chain end.     

Photo-living radical polymerization of methyl methacrylate by a nitroxide mediator

The novel photo-living radical polymerization was determined using 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl (MTEMPO) and bis(alkylphenyl)iodonium hexafluorophosphate (BAI) as the photo-acid generator. The polymerization of methyl methacrylate was performed using azobisisobutylonitrile as an initiator in the presence of MTEMPO and BAI at room temperature by irradiation with a high-pressure mercury lamp to produce poly(methyl methacrylate) with a comparatively narrow molecular weight distribution (M _w/M _n?=?1.3–1.7). The polymerization proceeded by a living mechanism based on the fact that the first-order time-conversion plots linearly increased. A linear increase in the plots of the molecular weight versus the conversion also supported the living nature of the polymerization. It was found that MTEMPO had an interaction with the propagation chain end to control the molecular weight, while BAI weakened the interaction of MTEMPO with the propagation chain end to reduce the molecular weight distribution and polymerization time.     

Cationic polymerization of isobutylene with H2O/TiCl4 initiating system in the presence of electron pair donors

Cationic polymerization of isobutylene (IB) in a mixture of methylene dichloride (CH₂Cl₂) and n-hexane (n-Hex) was conducted by using H₂O as initiator, TiCl₄ as co-initiator in the presence of strong external electron pair donor (ED), such as pyridine (Py), dimethylacetamide (DMA) or triethylamine (TEA). The effects of ED concentration, TiCl₄ concentration, solvent polarity, polymerization temperature (T) and time on IB polymerization, molecular weight (MW) and molecular weight distribution (MWD, M_w/M_n) of polyisobutylene (PIB) products were investigated. The relative amount of polymer formed via uncontrolled initiation by conventional active species (I) decreased with increasing the solvent polarity, TiCl₄ concentration and ED concentration in the polymerization. The desirable polymerization of IB with apparent absence of chain transfer reactions could be obtained by H₂O/TiCl₄ initiating system in the presence of ED under the appropriate reaction conditions. The external electron pair donors and TiCl₄ did specially play important and effective roles on polymerization.     

Photo-controlled/living radical polymerization of 2-(dimethylamino)ethyl methacrylate using 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl as a mediator

The photo-controlled/living radical polymerization of 2-(dimethylamino)ethyl methacrylate (DMAEMA) was attained using 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl as the mediator and (2RS,2′RS)-azobis(4-methoxy-2,4-dimethylvaleronitrile) (r-AMDV) as the initiator. The bulk polymerization of DMAEMA produced a polymer with a comparatively narrow molecular weight distribution below 1.6. The first-order time conversion plots showed a linear increase. The molecular weight of the resulting polymer also increased with an increase in the monomer conversion. The molecular weights of the resulting polymers were in good agreement with the theoretical molecular weights. A linear correlation was also obtained for the plots of the molecular weight vs. the reciprocal of the initial concentration of r-AMDV. The GPC analysis demonstrated the living nature of the polymerization based on the fact that the curves were shifted to the higher molecular weight side without deactivation as the conversion increased.     

Novel Epoxide Initiators for the Carbocationic Polymerization of Isobutylene

Summary: We recently reported the synthesis of polyisobutylene (PIB) via direct initiation by epoxycyclohexyl isobutyl polyhedral oligomeric silsesquioxane (POSS®) (Figure 1 ) in conjunction with titanium tetrachloride (TiCl₄). This system successfully initiated the living carbocationic polymerization of isobutylene (IB) in hexane/methyl chloride (Hx/MeCl -60/40, v/v) at T = −80 °C, yielding an asymmetric telechelic PIB with one POSS® cage head group and one tert-Cl end group. 1 This paper will discuss IB polymerizations initiated by 1,2-epoxycyclohexane and bis[3,4-(epoxycyclohexyl)ethyl]-tetramethyl-disiloxane, in conjunction with TiCl₄.     

(CH3)3SiCl/TiCl4 INITIATING SYSTEM FOR CATIONIC POLYMERIZATION OF 1,3-PENTADIENE

Cationic polymerizations of 1,3-pentadiene (PD) initiated by trimethylsilyl chloride (TMSCl) incombination with TiCl_4 were carried out in n-hexane at 30℃. The yield of polymer was greatly increased bythe addition of TMSCl, indicating that the TMSCl/TiCl_4 combination is an efficient initiating system for PDcationic polymerization. However, the introduction of TMSCl gave rise to a drop in the molecular weight ofthe polymer. Kinetic results demonstrated that the polymerization initiated by TMSCl/TiCl_4 is 4.5 times fasterthan that induced by TiCl_4 alone. Various ethers were used to mediate the TMSCl/TiCl_4 initiating system.Adding diphenyl ether could increase both the yield and molecular weight of the polymer. Structural evidenceillustrates that the polymerization is indeed initiated by TiCl_4 in combination with HCl resulting fromhydrolysis by adventitious water.     

Photo-controlled/living radical polymerization of tert-butyl methacrylate in the presence of a photo-acid generator using a nitroxide mediator

The photo-controlled/living radical polymerization of tert-butyl methacrylate was performed using a (2RS,2′RS)-azobis(4-methoxy-2,4-dimethylvaleronitrile) initiator and a 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl (MTEMPO) mediator in the presence of a (4-tert-butylphenyl)diphenylsulfonium triflate photo-acid generator. The bulk polymerization was carried out at 25 °C by irradiation with a high-pressure mercury lamp. Whereas the polymerization in the absence of MTEMPO produced a broad molecular weight distribution, the MTEMPO-mediated polymerization provided a polymer with a comparatively narrow molecular weight distribution around 1.4 without elimination of the tert-butyl groups. The living nature of the polymerization was confirmed on the basis of the linear correlations for the first-order time–conversion plots and conversion–molecular weight plots in the range below 50% conversion. The block copolymerization with methyl methacrylate also supported the livingness of the polymerization based on no deactivation of the prepolymer.     

Quasiliving Carbocationic Polymerization. XVII. Synthesis Of Poly (Styrene-β-Isobutylene-β-Styrene)

Poly(styrene-b-isobutylene-b-styrene) has been synthesized by sequential carbocationic polymerization under quasiliving conditions at -90°C. The quasiliving synthesis was effected by first continuously and slowly condensing gaseous isobutylene (IB) to a bifunctional initiating system (p-dicumyl chloride/TiCl₄) dissolved in a hexane-methylene chloride (60:40 v/v) mixture. After the quasiliving polyisobutylene (PIB) sequence had reached a desired molecular weight, styrene (St) was continuously and slowly added to produce the polystyrene (PSt) sequence. The products consisted of the target triblock. However, due to initiation by impurities and possibly to chain transfer to both IB and St, it also contained diblocks and small amounts of homopolymers. While the latter could be removed by selective fractionation, the triblocks and diblocks could not be separated. The mechanism of quasiliving polymerization leading to PIB/PSt blocks is discussed.     

Synthesis and Characterization of PS-PIB-PS Triblock Copolymers

Abstract

Poly(styrene-isobutylene-styrene) (PS-PIB-PS) block copolymers synthesized via living carbocationic polymerization using a di- or tricumyl chloride/TiCl₄/pyridine initiating system in 60/40 (v/v) hexane/methyl chloride cosolvents. The kinetics of formation of the PIB block at ? 80°C were found to be first order in isobutylene (IB) concentration, first order in the concentration of initiating sites, second order in TaiCl₄ concentration, and a negative fractional order with respect to the pyridine concentration. The rate of polymerization was found to decrease with increasing temperature, indicating an equilibrium between dormant, covalent and active, ionized chain ends, and chain-end concentration studies suggested that there was no contribution by free ions to the rate of propagation. Diagnosis of the livingness of the IB polymerization indicated that at high (≥90%) monomer conversion, β-proton elimination becomes important, causing the timing of addition of styrene to be critical. Addition of styrene at an IB reaction time significantly exceeding the time necessary for complete IB consumption resulted in contamination of the product with a substantial amount of homo-PS; conversely, addition at intermediate IB conversion resulted in slow copolymerization between IB and styrene and the formation of a tapered block copolymer. Addition of styrene at an IB conversion of about 90% resulted in well-defined block copolymers which displayed ordered, phase-separated morphologies consisting of cylinders of PS in a continuous phase of PIB. The block copolymers possessed properties consistent with those of physically crosslinked rubbers. Dynamic mechanical spectroscopy revealed two glass transitions with a broad rubbery plateau extending from about 0 to 100°C, and tensile strengths of up to 25 MPa and elongations to 1000% were observed for some samples.     

Kinetic study of the living cationic polymerization of isobutylene using t-Bu-m-DCC/TICL4/2,4-dimethylpyridine initiating system

Kinetics of the living cationic polymerization of isobutylene, initiated by the system t-bu-m-DCC/TiCl₄/2,4-dimethylpyridine (2,4-DMP), were studied as a function of concentration of the various components of the initiation system, solvent polarity, and presence of the protic acid scavenger, 2,6-di-tert-butylpyridine (DTBP). Under a variety of conditions, the effective number of growing chains in a given polymerization remained constant and Mn increased linearly with monomer conversion. The system was found to yield an essentially homogeneous reaction mixture in hexanes/methyl chloride cosolvents, with only a small amount of precipitate, probably 2,4-dimethylpyridinium salts resulting from proton scavenging by the tertiary amine. It was found that increasing [TiCl₄] strongly increased the rate while increasing [2,4-DMP] weakly decreased the rate. Evidence of a retardation of the polymerization rate by the soluble TiCl₄:2,4-DMP complex was observed. The addition of DTBP as a protic acid scavenger, with or without 2,4-DMP, very weakly decreased the rate of polymerization. Increasing the fraction of methyl chloride in the solvent mixture caused an increase in the rate of polymerization. All of the results were consistent with a propagation mechanism in which an equilibrium exists between dormant and ionized, active chain ends.     

Living Carbocationic Polymerization. XLIX. Two-Stage Living Polymerization of Isobutylene to Di-tert-chlorine Telechelic Polyisobutylene

Abstract

A two-stage process was developed for the living polymerization of isobutylene (IB) employing di-tert-alcohol initiators in conjunction with BCl₃ coinitiator in the first or initiation stage, followed by TiCl₄ coinitiator in the second or propagation stage; the process was shown to yield high molecular weight (up to M ⁿ 20,000), narrow molecular weight distribution (MWD) M ^w/M ⁿ = 1.1–1.2) di-tert-chlorine telechelic polyisobutylenes (^tCl-PIB-Cl^t). The initiation stage involves the homogeneous solution living polymerization of IB induced by the di-tert-alcohol/BCl₃ combination in the presence of an electron donor such as N,N-dimethylacetamide in CH₃Cl solvent at ?80°C and proceeds up to M ⁿ < 5000; this is followed by the propagation stage in which TiCl₄ and the bulk of IB plus a sufficient amount of n-C₆H₁₄ are added to the charge to bring the solvent composition to CH₃Cl/n-C₆H₁₄ 60/40 v/v and the living polymerization is continued until high M ⁿ product is obtained. This two-stage process was developed because 1) it employs very inexpensive chemicals; 2) di-tert-alcohol/BCl₃ combinations initiate living IB polymerization in CH₃Cl but the product after reaching M ⁿ ≤ 5000 precipitates out of the CH₃Cl solution, and di-tert-alcohol/BCl₄ combinations do not initiate IB polymerization; and 3) di-tert-alcohol/BCl₃ systems do not initiate (or only very slowly) the living polymerization of IB in CH₃Cl/n-C₆H₁₄ mixtures, whereas similar TiCl₄-based systems do. The polymerization remains living during both stages although the propagating species and solvent polarity are profoundly altered. The livingness of the system has been analyzed by kinetic experiments and the structure of the ^tCl-PIB-Cl^t product by routine spectroscopic means.     

一氯二乙基铝／氯苄／吡啶引发体系引发的异丁烯阳离子聚合

活性聚合是控制聚合物的分子量、分子量分布、结构和端基的最有效和简单的方法之一。就异丁烯单体(IB)而言,自Kennedy首次报道其活性阳离子聚合以来,陆续报道了一些新的活性引发聚合体系,这些体系主要有两类:一类是叔丁基的酯、醚、醇与路易斯酸构成的引发体系;另一类是特丁基氯与路易斯酸加电子给予体(如DMSO、DMA等),其中以     

Nitroxide-mediated photo-living radical polymerization of methyl methacrylate in solution

The photoradical polymerization of methyl methacrylate (MMA) was performed in an acetonitrile solution at room temperature using (2RS,2′RS)-azobis(4-methoxy-2,4-dimethylvaleronitrile) as the initiator, 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl as the mediator, and (4-tert-butylphenyl)diphenylsulfonium triflate as the photo-acid generator. This solution polymerization showed a non-steady-state during the very early stage followed by a steady-state. The polymerization produced oligomers with several thousand molecular weights at a very low conversion under the non-steady-state. It was confirmed that the polymerization proceeded in accordance with a living mechanism under the steady-state based on the linear correlations for both the first-order time-conversion plots and the conversion–molecular weight plots. The molecular weight distributions of the polymers obtained in the steady-state were approximately 1.8. The block copolymerization with isopropyl methacrylate ( ⁱ PMA) demonstrated that the growing polymer chain ends of the MMA prepolymer were stabilized even at a high conversion and efficiently initiated the ⁱ PMA polymerization.     

Polyisobutylene-Based Thermoplastic Elastomers. I. Synthesis and Characterization of Polystyrene-Polyisobutylene-Polystyrene Triblock Copolymers

Abstract

Polystyrene-polyisobutylene-polystyrene triblock copolymer thermoplastic elastomers have been synthesized by living carbocationic sequential copolymerization using the tert-butyl dicumyl chloride/TiCl₄/methylcyclohexane:methyl chloride (60:40 v:v)/ ?80°C system in the presence of the proton trap 2,6-di-tert-butylpyridine. Structure-property relationships have been examined by varying the M_n of the PIB middle block (39,000 to 156,000) and that of the PSt end-segment (1,000 to 19,000). The tensile strength is controlled by the molecular weight of the PSt segment and independent of the PIB middle block length in the studied range. Phase separation starts when the M_n of the PSt segment reaches ～ 5,000, and it is complete when the M_n reaches ～ 15,000. These triblocks exhibited 23-25 MPa tensile strength, similar to that of styrenic thermoplastic elastomers obtained by anionic polymerization.     

SET‐LRP of methyl methacrylate initiated with sulfonyl halides

Single electron transfer‐living radical polymerization (SET‐LRP) represents a robust and versatile method for the rapid synthesis of macromolecules with defined architecture. The present article describes the polymerization of methyl methacrylate by SET‐LRP in protic solvent mixtures. Herein, the polymerization process was catalyzed by a straightforward Cu(0)wire/Me₆‐TREN catalyst while initiation was obtained by toluenesulfonyl chloride. All experiments were conducted at 50 °C and the living polymerization was demonstrated by kinetic evaluation of the SET‐LRP. The process follows first order kinetic until all monomer is consumed which was typically achieved within 4 h. The molecular weight increased linearly with conversion and the molecular weight distributions were very narrow with M_w/M_n ～ 1.1. Detailed investigations of the polymer samples by MALDI‐TOF confirmed that no termination took place and that the chain end functionality is retained throughout the polymerization process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2236–2242, 2010