Graft Copolymerization of Methyl Methacrylate onto Poly(Ethylene Terephthalate) Fibers Using Benzoyl Peroxide

Abstract

The graft copolymerization of methyl methacrylate onto poly(ethylene terephthalate) fibers has been studied using benzoyl peroxide as initiator. The grafting reactions were carried out within the 70 to 90°C temperature range, and the variations of graft yield with monomer and initiator concentrations were also investigated. The overall activation energy for grafting was calculated as 34.1 kcal/mol. The results of dyeability with the disperse dye suggested that diffusion into the fiber structure was moderately difficult when the graft yield reached 14?15%. The maximum graft yield was obtained at a benzoyl peroxide concentration of 4.00 × 10^?3 M. The decomposition temperature values obtained from thermogravimetric analysis show that the thermal stability of poly(ethylene terephthalate) fibers decreased as a result of grafting. Further, such change in the properties of methyl methacrylate grafted fibers as density, diameter, and moisture regain were also determined.     

Grafting of Acrylamide On 1, 1, 2, 2-Tetra-Chloroethane Preswelled Polyethylene Terephthalate) Films Using Azobisisobutyronitrile Initiator

Abstract

Graft polymerization of acrylamide (AAm) on 1, 1, 2, 2 tetrachloro-ethane (TCE) preswelled poly(ethylene terephthalate) (PET) films were performed with chemical initiation method using asobisiso-butyronitrile (AIBN) initiator. Temperature was found to have a greater effect on the swelling then the swelling time. Variation of the graft yield with polymerization temperature, time, AIBN concentration, AAm concentration, AIBN and AAm inclusion times were investigated. The optimum temperature for grafting was found to be 70°CC. The graft yield was observed to increase with polymerization time, AAm concentration, initiator and monomer diffusion time up to a saturation graft yield and then leveled off. An increase in AIBN concentration first enhanced the percent grafting then showed a decrease. The addition of some salts (Ni²⁺, Cr³⁺, Co²⁺, Cu²⁺) on the rate of grafting was also investigated. From the temperature dependence of the initial rate of grafting, the overall activation energy was found to be 4. 1 kcal/mol and relevant rate equation have been derived. The effect of grafting on film propities, such as water absorption capacity, intrinsic viscosity were determined. Grafted films were characterized by FTIR spectros-copy and scanning electron microscopy (SEM).     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Graft Copolymerization of Methyl Methacrylate onto Nylon 6 Using Thallium(III) Ions as Initiator

Abstract

Graft copolymerization of methyl methacrylate onto nylon 6 was investigated in aqueous perchloric acid medium using thallium(III) ions as initiator. The rate of grafting was evaluated by varying the concentrations of monomer, initiator, acid, and temperature. The rate of grafting was found to increase with an increase of both monomer and initiator concentrations. The graft yield was found to increase with an increase in the acid concentration up to 0.49 mL^?1, and beyond this concentration of perchloric acid the graft yield was found to decrease. It also increased with an increase of temperature. From the Arrhenius plot the overall activation energy was found to be 3.9 kcal/mol. The effects of inhibitors, various solvents, inorganic salts, and swelling agents on graft yield were studied. A suitable kinetic scheme has been proposed and a rate equation has been derived.     

Analysis and Characterization of Microwave Irradiation–Induced Graft Copolymerization of Methyl Methacrylate onto Delignified Grewia Optiva Fiber

Grafting of methyl methacrylate (MMA) onto delignified Grewia optiva fiber using ascorbic acid/H₂O₂ as an initiator was carried out under microwave irradiation. The effects of varying the microwave power, exposure time, and concentration of initiator and monomer of graft polymerization were studied to obtain maximum grafting percentage (26.54%). The experimental results showed that the optimal conditions for grafting were: exposure time, 10min; microwave power, 110 W; ascorbic acid concentration, 3.74mol/L × 10^?2; H₂O₂ concentration, 0.97mol/L × 10^?1; monomer concentration, 1.87mol/L × 10^?1. The graft copolymers were characterized by Fourier transform-infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA).     

Ceric Ion-Initiated Grafting of Poly(Methyl Acrylate) onto Chitin

Abstract

Poly(methy1 acrylate) was grafted onto chitin in an aqueous medium by using the ceric ion as a redox initiator in the presence of 10^?4 M nitric acid and oxygen from the atmosphere. The grafting percentage turned out to be dependent on reaction temperature, time, and initiator concentration, but it was found to be independent of monomer concentration. In the course of the grafting reaction, homopolymerization of methyl acrylate occurs. The percentage of homopolymer was found to depend only on the reaction temperature. The apparent activation energy for the grafting reaction was estimated to be 11 kcal/mol. The grafted chitin is insoluble in solvents for chitin but shows enhanced swelling in some organic solvents.     

Synthesis of Acid Dyeable Acrylonitrile Copolymer

In this paper, a unique and updated technique was applied to obtain an acid dyeable copolymer of acrylonitrile by solution polymerization of acrylonitrile, and a kind of alkaline monomer F (N,N‐dialkylaminoethylacrylate). Azodiisobutyronitrile (AIBN) was used as initiator to prepare the copolymer in sodium sulfocyanate aqueous solution. The effect of initiator concentration on the polymer's molecular weight and conversion during polymerization was studied. The relation between concentration of the alkaline monomer F and the polymer conversion, as well as the relation between concentration of the alkaline monomer F and the % dye‐uptake of the copolymer are discussed. The influence of pH was also researched. The structure of the copolymer was characterized by IR and NMR. The copolymer has excellent acid dyeable characteristics.     

GRAFT COPOLYMERIZATION OF METHYL ACRYLATE ONTO CHITOSAN INITIATED BY POTASSIUM DIPERIODATONICKELATE (IV)

ABSTRACT

A novel redox system, potassium diperiodatonickelate [Ni (IV)]‐chitosan, was employed to initiate the graft copolymerization of methyl acrylate (MA) onto chitosan in alkali aqueous solution. The effects of reaction variables such as monomer concentration, initiator concentration, reaction time, pH and temperature were determined. By means of a series of copolymerization, the grafting conditions were optimized. The maximum grafting percentage obtained was 404.1% when 0.3 g chitosan was copolymerized with 1.8 mL monomer at 35°C for 5 hours with [Ni (IV)]=9.4×10^?4 M and the total volume was 20 mL. Ni (IV)-chitosan system is found to be an efficient redox initiator for this graft copolymerization. A single electron transfer mechanism is proposed to explain the formation of radicals and the initiation. The grafted copolymers were characterized by IR and X-ray diffraction diagrams. The thermal stability of chitosan and chitosan-g-PMA was studied by thermogravimetric analysis (TGA).     

Synthesis and Characterization of Chitosan‐graft‐Poly(3‐(trimethoxysilyl)propyl methacrylate) Initiated by Ceric (IV) Ion

The grafting of 3‐(trimethoxysilyl)propyl methacrylate (TMSPM) onto chitosan by ceric ion initiation was studied under homogeneous conditions in 2% acetic acid solution. The grafted polymer was characterized by FT‐IR, ¹H‐NMR, TGA and XRD and swelling studies. TGA results showed that the incorporation of TMSPM to the chitosan chains decreased the thermal stability of the grafted chitosan. Due to the grafting of TMSPM, the crystallinity of chitosan derivatives was found to be destroyed. The solubility of the grafted chitosan in water was improved. The effects of reaction conditions such as initiator concentration, monomer concentration, reaction temperature and reaction time were studied by determining the grafting parameters such as grafting and grafting efficiency. Under optimum conditions, the grafting parameters were achieved as 1440 and 97%, respectively.     

Grafting Vinyl Monomers onto Silk Fibers: Graft Copolymerization of Vinyl Monomers onto Silk Using the Vanadyl Acetylacetonate Complex

Abstract

The graft copolymerization of methyl methacrylate (MMA) onto mulberry silk fibers was studied in aqueous solution using the acetylacetonate oxovanadium (IV) complex. The rate of grafting was investigated by varying the concentration of the monomer and the complex, the acidity of the medium, the solvent composition of the reaction medium, the surfactants, and the inhibitors. The graft yield increases with increasing concentration of the initiator up to 8.75 × 10^?5 mol/L, of the monomer up to 0.5634 mol/L, and thereafter it decreases. Among the various vinyl monomers studied, MMA was found to be most suitable for grafting. Grafting increases with increasing concentration of HCIO₄ and with increasing temperature. Inhibitors like picryl chloride and hydroquinone significantly decrease the extent of grafting. Alcoholic solvents at a solvents/water ration of 10:90 seem to constitute the most favorable medium for grafting. A suitable reaction scheme has been proposed, and the activation energy calculated from the Arrhenius plots.     

Characterization and Studies on Grafting of Methyl Methacrylate onto PAN Fibers

The graft copolymerization of methyl methacrylate (MMA) onto commercial acrylic fibers (PAN) has been studied using Azobis(isobutyro)nitrile (AIBN) as an initiator. MMA grafting initiated by radicals formed from thermal decomposition of AIBN. In this study, the effects of monomer and initiator concentration, time and temperature reaction on the grafting yield have been investigated.

The optimum conditions for this grafting reaction were obtained with an MMA concentration of 0.7 M, an AIBN concentration of 0.0073 M, a reaction temperature of T=85°C and with a 60 min reaction time.

The fiber structure has been investigated by different experimental techniques of characterization such as Fourier transform infrared spectroscopy (FT‐IR), calorimetric analysis (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), water absorption and the physical and mechanical properties has also been investigated in this study. The thermal analysis data showed that by increasing grafting yield, little changes have occurred in fibers samples up to 13.5% of grafting yield and the thermal transitions of grafted fibers have approximately the same behavior compared with the raw fibers sample. Grafting also slightly affected the fiber morphology. The experimental data of mechanical properties clearly show that by increasing grafting yield, max extension will decrease but this change up to 13.5% grafting yield is barely noticeable. Grafting of poly MMA improved water absorption.     

Graft copolymerization. I. Grafting of hydroxyalkyl methacrylates on poly(vinyl alcohol)

New graft copolymers were synthesized by grafting hydroxyethyl methacrylate and hydroxpropyl methacrylate on poly(vinyl alcohol) in aqueous solution with Ce⁺⁴ions as initiator. The dependence of the percentage of grafting and monomer conversion on the concentration of the monomer, on the concentration of the initiator, on the total concentration of the reactants, and on temperature and duration of the reaction were investigated. Some basic properties of the graft copolymers and some preliminary permeation measurements of water vapors through films, made from these copolymers, are also reported.     

A study of the graft copolymerization of methacrylic acid onto starch using the H2O2/Fe++ redox system

Graft copolymerization of methacrylic acid (MetAc) onto potato starch using H₂O₂/Fe⁺⁺ redox system was investigated. The best conditions of the grafting reaction were determined and several variables were studied: initiator and monomer concentrations, time, and temperature. Percent grafting efficiency, percent grafting, percent grafted monomer conversion, and total conversion were obtained. The optimum graft yield was obtained at 7.3 × 10^?3M H₂O₂ concentration and it was favored by increasing the methacrylic acid concentration and reaction time.     

Graft copolymerization. II. Grafting of benzyloxyethyl methacrylate on poly(vinyl alcohol)

New graft copolymers were produced by grafting benzyloxyethyl methacrylate, the benzyl ether of HEMA, on high-molecular-weight poly(vinyl alcohol) in dimethyl sulfoxide solution with Ce⁴⁺ as initiator. The effects of the concentration of the initiator, the concentration of the monomer, the total concentration of the reactants, the temperature, and the duration of reaction on the percentages of grafting and conversion were investigated. Further, also the relationships between the initiator concentration and the percentages of grafting and of conversion in the reaction with poly(vinyl alcohol)s of lower molecular weight and of different degrees of hydrolysis were studied.     

Solvent “Goodness” in Polymer Separation by Flow

The graft copolymerization of methyl methacrylate onto silk fibers was investigated in aqueous solution using the V⁵⁺?thiourea redox system. The rate of grafting was determined by varying monomer, thiourea, acidity of the medium, temperature, initiator concentration, and reaction medium. The percentage of graft yield increases significantly by increasing the initiator concentration up to 0.01 M and thereafter decreases with a further increase of initiator concentration. The graft yield increases with an increase of thiourea concentration up to 10.0 × 10^?4 and then decreases with a further increase of thiourea concentration. The effect of increasing the monomer concentration brings about a significant enhancement in the graft yield. A suitable kinetic scheme has been proposed and the rate equation has been evaluated.     

聚环氧乙烷大单体与丙烯酸乙酯的共聚及其规整接枝共聚物的表征

 本工作研完了末端为甲基丙烯酸酯型的聚环氧乙烷大单体与丙烯酸乙酯的溶液自由基共聚。结果表明,大单体接枝效率和共聚物分子量受单体总浓度、投料比、大单体分子量及引发剂等的影响,接枝效率最高可达90％以上,分子量可在5-15×10⁴范围内变化。丙烯酸乙酯与大单体共聚的竞聚率为0.83。共聚物用萃取法精制后,用IR、¹H-NMR、裂解色谱、GPC和膜渗透压计等进行了表征。证实产物有预期的规整接枝共聚物结构。平均接枝数为2—11。     

Graft copolymerization onto rubber. V. Graft copolymerization of methyl methacrylate onto rubber using potassium peroxydiphosphate as initiator

The graft copolymerization of methyl methacrylate onto natural rubber (NR) is investigated using potassium peroxydiphosphate as the initiator. The rate of grafting is determined by varying monomer concentration, peroxydiphosphate concentration, and temperature. The graft yield increased with an increase in monomer concentration up to 1.4082M/L and thereafter the graft yield decreases. The graft yield increases significantly with an increase of peroxydiphosphate concentration up to 150 X 10^-1M/L and thereafter the graft yield decreases. The grafting reaction is temperature dependent. A suitable kinetic scheme is proposed and the rate equation is evaluated.     

Synthesis and characterization of anhydride-functional polycaprolactone

Polycaprolactone-graft-maleic anhydride (PCL-g-MA) copolymer was prepared by grafting maleic anhydride onto PCL in a batch mixer and in an extruder using dicumyl peroxide as the initiator. The graft content was determined with the volumetric method by converting the anhydride functions to acid groups and then titrating with ethanolic potassium hydroxide. The grafted polymer was extracted with xylene to remove any unreacted monomer before the estimation step. The effect of temperature and the various concentrations of the initiator and monomer used for the grafting reaction were investigated. The presence of residual initiator in the reaction product was checked using thin-layer chromatography. Molecular weight determination was carried out for the pure and grafted polymer using gel permeation chromatography to determine if chain scission was present. Results indicate that maleic anhydride is grafted onto PCL using free radical initiators. The grafting reaction was confirmed by FTIR and NMR techniques. FTIR spectra showed absorption bands around 1785 and 1858 cm⁻¹. NMR spectra gave signals for methine proton at 3.47 ppm. For a given peroxide level, a higher temperature or residence (reaction) time gave higher percentage of grafted MA. There was an optimum temperature and initiator concentration after which the percentage of MA grafted on PCL decreased. The number-average molecular weight, tensile strength, and the percent elongation of PCL-g-MA were comparable to those of PCL before grafting. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1139–1148, 1997     

Grafting Vinyl Monomers onto Silk Fibers. XIII. Graft Copolymerization of Methyl Methacrylate onto Silk Using Fe3+−Cysteine Redox System

The graft copolymerization of methyl methacrylate onto silk fibers initiated by the ferric chloride-eysteine redox system has been investigated in aqueous medium. The rate of grafting was calculated by varying the concentrations of monomer, initiator, acidity of the medium, cysteine, and temperature. The percentage of grafting increases with an increase of Fe³⁺ concentration up to 2,5 × 10^?3 mol/L and thereafter it decreases. The graft yield increases steadily upon increasing the monomer concentration. The graft yield also increases with increasing cysteine concentration up to 0.5 × 10^?3 mol/L and then decreases. The effect of the perchloric acid concentration, temperature, solvents, and certain neutral salts on graft yield has also been investigated and a suitable reaction scheme has been proposed.     

Graft Copolymerization of Acrylamide on Swollen poly (Ethylene Terephthalate) Fibers Using Cerium Ammonium Nitrate Initiator

Abstract

In this study the graft copolymerization of acrylamide (AAm) on swollen poly(ethylene terephthalate) (PET) fibers using cerium ammonium nitrate (CeAN) initiator was investigated. Five organic solvents, dimethylsulfoxide (DMSO), morpholine, acetic acid (HAc), n-butanol, and 1,2-dichloroethane (DCE), were used as swelling agents. DMSO was found to be the most suitable swelling agent. Solvent diffusion into the fibers was observed to increase with treatment time and temperature. The optimum graft yield was obtained when fibers were grafted after having been swollen in DMSO for a period of 1 hour at 140°C. Variation of graft yield with polymerization time and temperature, and monomer, initiator, and acid concentrations were investigated. Graft yields were observed to increase initially with polymerization time, then to level off, and were found to increase up to a certain monomer and Ce⁴⁺ concentration, then to decrease slightly. The effect of grafting on such fiber properties as diameter, viscosity, and moisture gain were also investigated.